Wyszukiwarka
Filtry
wszystkich: 136
Wyniki wyszukiwania dla: modal identification
-
Study on applicability of two modal identification techniques in irrelevant cases
PublikacjaStudy on applicability of two modal identification techniques in irrelevant cases is made in this paper. The following techniques are considered: Peak Picking based on correlation analysis (PP-CA), dedicated for ambient vibrations and Eigensystem Realization Algorithm (ERA), formulated for free decay vibrations investigation. Irrelevant cases are found when analyzed signals are different than recommended to a given technique. The...
-
A dynamic vehicle-bridge model based on the modal identification results of an existing EN57 train and bridge spans with non-ballasted tracks
PublikacjaThis paper addresses the methodology of the bridge-vehicle dynamic model definition based on the free response measurements of an existing train and existing bridge spans. In the case of the railway vehicle, the methodology uses the impulse excitations of a single car by means of the wedge method. In the case of the bridge spans, free responses are collected after the passages of trains. The global modal parameters (frequencies...
-
Modal parameters identification with Particle Swarm Optimization
PublikacjaThe paper presents method of the modal parameters identification based on the Particle Swarm Optimization (PSO) algorithm [1]. The basic PSO algorithm is modified in order to achieve fast convergence and low estimation error of identified parameters values. The procedure of identification as well as algorithm modifications are presented and some simple examples for the SISO systems are provided. Results are compared with the results...
-
Spectrum-based modal parameters identification with Particle Swarm Optimization
PublikacjaThe paper presents the new method of the natural frequencies and damping identification based on the Artificial Intelligence (AI) Particle Swarm Optimization (PSO) algorithm. The identification is performed in the frequency domain. The algorithm performs two PSO-based steps and introduces some modifications in order to achieve quick convergence and low estimation error of the identified parameters’ values for multi-mode systems....
-
SPECTRAL-BASED MODAL PARAMETERS IDENTIFICATION WITH MULTIPLE PARTICLE SWARMS OPTIMIZATION
PublikacjaThe paper presents usage of a Particle Swarm Optimization [1] based algorithm for spectral-based modal parameters identification. The main algorithm consists of two groups of swarms, namely, scouts and helpers. For the first group additional penalizing process is provided to force separation of scouting swarms in frequency space. The swarms have an ability to communicate with each other. At first stage, each swarm focuses on a...
-
Material Parameters Identification of Historic Lighthouse Based on Operational Modal Analysis
PublikacjaIn the present paper, the identification of the material parameters of a masonry lighthouse is discussed. A fully non-invasive method was selected, in which the material properties were determined via numerical model validation applied to the first pair of natural frequencies and their related mode shapes, determined experimentally. The exact structural model was built by means of the finite element method. To obtain experimental...
-
Modal energy identification of large stucture idealised by the finite element method
PublikacjaPrzedstawiono metodę określania energii drgań układów dyskretnych otrzyma-nych w wyniku modelowania metodą elementów skończonych wybranych fragmentów konstrukcji samochodów. W odróżnieniu od poprzednio stosowanych podejść, ro-zważa się całkowite energie mechaniczne odpowiadające poszczególnym posta-ciom drgań własnych. Całkowitą energię mechaniczną oblicza się na podstawie parametrów modelu modalnego. Energię mechaniczną można...
-
Identification of the Vistula Mounting tower model using measured modal data
PublikacjaW pracy przedstawiono problem identyfikacji pięcioparametrowego modelu zabytkowej wieży twierdzy Wisłoujście. Poszukiwane parametry wyznaczono jako rozwiązanie problemu minimalizacji błędu średniokwadratowego pomierzonych dwóch pierwszych częstości i pierwszej postaci drgań własnych. Do tego celu wykorzystano hierarchiczną procedurę minimalizacji przy zastosowaniu analizy wrażliwości. Analiza numeryczna potwierdziła efektywność...
-
Identification of Kinematic Excitation Function by the Modal Coordinates Estimation of the System's Dynamics
PublikacjaThe paper presents a method of the kinematic excitation courses’ identification in excitation points, based on the car road test acceleration at different measurement points. For the purpose of the laboratory fatigue life investigation of contemporary complex structures (e.g. cars bodies) and components of these structures (i.e. cars roofs), only a few first vibration modes are usually taken into account. During real life tests...
-
Modal properties identification of a novel sandwich footbridge – Comparison of measured dynamic response and FEA
PublikacjaA modern sandwich composite footbridge made of high-tech materials, being an example of practical application of laminated composites in civil engineering, is presented. The in situ non-destructive testing of the footbridge, aiming to identify modal properties and pedestrian comfort, is described. The measured eigenmodes and eigenfrequencies are compared with numerically estimated values. Finite element analyses of the footbridge...
-
Uncertainty quantification of modal parameter estimates obtained from subspace identification: An experimental validation on a laboratory test of a large-scale wind turbine blade
PublikacjaThe uncertainty afflicting modal parameter estimates stems from e.g., the finite data length, unknown, or partly measured inputs and the choice of the identification algorithm. Quantification of the related errors with the statistical Delta method is a recent tool, useful in many modern modal analysis applications e.g., damage diagnosis, reliability analysis, model calibration. In this paper, the Delta method-based uncertainty...
-
Uncertainty Quantification in Experimental Structural Dynamics Identification of Composite Material Structures
PublikacjaComposite materials are widely used in manufacture of aerospace and wind energy structural components. These load carrying structures are subjected to dynamic time-varying loading conditions. Robust structural dynamics identification procedure impose tight constraints on the quality of modal models estimates obtained from vibration experiments. Modal testing results are influenced by numerous factors introducing uncertainty to...
-
Identification of plate dynamic parameters for structural health monitoring
PublikacjaPraca przedstawia technikę wyznaczania parametrów modalnych wykorzystywanych w diagnostyce konstrukcji. Modalna masa, sztywność, tłumienie i postacie drgań wyznaczone są dla prostokątnej stalowej płyty na podstawie badań eksperymentalnych. Teoretyczne parametry modalne otrzymaneo z modelu MES. Omówiony został wpływ dodatkowej masy na parametry modalne konstrukcji.This paper presents a technique for modal parameters estimation for...
-
Influence of statistical errors on damage detection based on structuralflexibility and mode shape curvature
PublikacjaDamage detection procedures based on measured natural frequencies and building structure mode shapes are discussed in this paper. Modal curvature and structural flexibility approaches are tested. Attention is paid to the modal identification errors that influence damage detection. This problem is studied using a computer simulation of a simple supported beam. For practical cases, the peak picking methodand its statistical errors...
-
Identification of dynamic parameters in the context of diagnostics of steel tank with different level of liquid.
PublikacjaThe paper presents an experimental study to identify the dynamic parameters of a water-filled tank model. The experimental modal analysis approach involving the excitation at one point of the structure and acquisition of vibra tions at selected points distri buted over the tank surface allowed to determine the resonance frequencies, mode shapes and damping ratios. The main aim of the research was to examine the influence of...
-
An Experimentally Aided Operational Virtual Prototyping to Obtain the Best Spindle Speed during Face Milling of Large-Size Structures
PublikacjaAbstract: The paper presents an original method concerning the problem of vibration reduction in the general case while milling large-size and geometrically complex details with the use of an innovative approach to the selection of spindle speed. A computational model is obtained by applying the so-called operational approach to identify the parameters of the workpiece modal model. Thanks to the experimental modal analysis results,...
-
Optimal spindle speed determination for vibration reduction during ball-end milling of flexible details
PublikacjaIn the paper a method of optimal spindle speed determination for vibration reduction during ball-end milling of flexible details is proposed. In order to reduce vibration level, an original procedure of the spindle speed optimisation, based on the Liao–Young criterion, is suggested. As the result, an optimal, constant spindle speed value is determined. For this purpose, on-stationary computational model of machining process is...
-
A technique of experiment aided virtual prototyping to obtain the best spindle speed during face milling of large-size structures
PublikacjaThe paper presents an original method concerning vibration suppression problem during milling of large-size and geometrically complicated workpieces with the use of novel way of selecting the spindle speed. This consists in repetitive simulations of the cutting process for subsequent values of the spindle speed, until the best vibration state of the workpiece is reached. An appropriate method of obtaining a computational model,...
-
Optimization of the spindle speed during milling of large-sized structures with the use of technique of Experiment-Aided Virtual Prototyping
PublikacjaIn the paper are presented considerations concerning vibration suppression problems during milling of large-sized workpieces with the use of innovative method of matching the spindle speed of cutting tool. It depends on repeatable change of the spindle speed value as soon as the optimal vibration state of the workpiece approaches. The values of dominant “peaks” in the frequency spectra and the Root Mean Square (RMS) values of time...
-
Dynamics of the small-span railway bridge under moving loads
PublikacjaThe paper presents the results of dynamic analysis of the small-span railway bridge, subjected to an action of moving trains. Numerical simulations were performed using three different load models: series of moving forces, series of moving single-mass and double-mass oscillators. The parameters of the vehicle were taken from the existing EN57 train. The parameters of the bridge were taken from the existing steel span of 10,24 m...
-
A method of predicting the best conditions for large-size workpiece clamping to reduce vibration in the face milling process
PublikacjaThe paper presents an innovative method of solving the problem of vibration suppression during milling of large-size details. It consists in searching for the best conditions for clamping the workpiece based on a rapid modal identification of the dominant natural frequencies only and requires repetitive changes in the tightening torque of the clamping screws. Then, by estimating the minimum work of the cutting forces acting in...
-
Identification of Risk Factors for Collisions Involving Cyclists Based on Gdansk Example
PublikacjaThe role of pedestrian and bicycle traffic in Poland has growing trend. The comprehensive traffic study, conducted in Gdansk in 2016, has confirmed the increase in the number of cyclists and their share in the modal split. Therefore, it is particularly important to ensure the safety of this group of unprotected road users. Only in 2015 on the roads of Gdansk occurred 93 accidents (excluding collisions) involving cyclists. As a...
-
Oddziaływania taboru na mosty kolejowe przy zmiennych parametrach ruchu
PublikacjaW pracy poruszono zagadnienia związane z identyfikacją oraz modelowaniem układu dynamicznego most-pojazd ruchomy. Za element szczególnie istotny uznano czynnik obciążający. Opracowano i wdrożono metodykę identyfikacji cech dynamicznych rzeczywistego pojazdu szynowego. Eksperyment badawczy przeprowadzono dla jednostki trakcyjnej EN57, jednak nie ma żadnych ograniczeń w stosowaniu metody dla innego, konwencjonalnego taboru szynowego....
-
Dynamic analysis of the railway bridge span under moving loads
PublikacjaThe first part of this paper provides a review of the state of knowledge of the dynamic behaviour of railway bridges under moving loads. Particular attention is paid to developments in modelling railway bridge loading and dynamic vehicle-span (structure) interaction. The most important aspects determining the advancements in this area of knowledge are identified. The contemporary techniques for defining bridge span finite element...
-
Nondestructive Testing of the Miter Gates Using Various Measurement Methods
PublikacjaWhen any problems related to civil engineering structures appear, identifying the issue through the usage of only one measuring method is difficult. Therefore, comprehensive tests are required to identify the main source. The strains and displacement measurements, as well as modal identification, are widely used in the nondestructive testing of structures. However, measurements are usually carried out at several points and confirm...
-
Experimental and Numerical Study on Dynamics of Two Footbridges with Different Shapes of Girders
PublikacjaThe paper presents the experimental and numerical results of the dynamic system identification and verification of the behavior of two footbridges in Poland. The experimental part of the study involved vibration testing under different scenarios of human-induced load, impulse load, and excitations induced by vibration exciter. Based on the results obtained, the identification of dynamic parameters of the footbridges was performed...
-
Globalized parametric optimization of microwave components by means of response features and inverse metamodels
PublikacjaSimulation-based optimization of geometry parameters is an inherent and important stage of microwave design process. To ensure reliability, the optimization process is normally carried out using full-wave electromagnetic (EM) simulation tools, which entails significant computational overhead. This becomes a serious bottleneck especially if global search is required (e.g., design of miniaturized structures, dimension scaling over...
-
Wpływ sposobu odwzorowania pojazdu szynowego na odpowiedź dynamiczną przęsła mostowego
PublikacjaW pracy przedstawiono rezultaty analiz numerycznych oraz badań eksploatacyjnych dwóch przęseł mostowych wymuszonych ruchomym pojazdem szynowym. Pojazd odwzorowano za pomocą czterech modeli uproszczonych: strumienia sił skupionych, strumienia mas skupionych oraz strumieni oscylatorów jedno- i dwumasowych. Analizy numeryczne wykonano przy wykorzystaniu MES. Potrzebne parametry dynamiczne wyznaczono na podstawie wyników identyfikacji...
-
Modelling and Simulation of a New Variable Stiffness Holder for Milling of Flexible Details
PublikacjaModern industry expectations in terms of milling operations often demand the milling of the flexible details by using slender ball-end tools. This is a difficult task because of possible vibration occurrence. Due to existence of certain conditions (small depths of cutting, regeneration phenomena), cutting process may become unstable and self-excited chatter vibration may appear. Frequency of the chatter vibration is close to dominant...
-
Vibration Surveillance System with Variable Stiffness Holder for Milling Flexible Details
PublikacjaEfficient milling of the flexible details (i.e. rotor blades, thin-walled elements) using slender ball-end tools is a difficult task due to possibility of vibration occurrence. Because of the existence of certain conditions (small depths of cutting, regeneration phenomena), cutting process may lose stability and self-excited chatter vibration may appear. Frequency of the chatter vibration is close to dominant natural frequency...
-
Hybrid Reduced Model of Continuous System
PublikacjaThe paper introduces an alternative method of modelling and modal reduction of continuous systems. Presented method is a hybrid one. It combines the advantages of modal decomposition method and the rigid finite element method. In the proposed method continuous structure is divided into one-dimensional continuous elements. For each 1D element modal decomposition and reduction is applied. Interactions between substructures are...
-
Modelling of pipes conveying flowing liquid
PublikacjaThe paper introduces the method of modal reduction of system which consists of pipe with flowing liquid. The concept of hybrid model is proposed. The system model consists of two parts, the modal model and the finite elements model. The modal model represents linear, self-adjoined part of the system, while simple lumped technique is applied for modelling of Coriolis phenomena.
-
Modal Reduction and Analysis of Gyroscopic Systems
PublikacjaThe paper introduces the method of the modal reduction of systems that experience the Coriolis acceleration or gyroscopic effect component. In such cases corresponding system equations are non-self-adjoined. To solve the problem modal reduced model is built up for the system without Coriolis acceleration or gyroscopic effect terms. These phenomena are included by application of any lumping technique. Hence, the final reduced model...
-
SIMPLIFIED DYNAMIC MODEL OF ROTATING BEAM
PublikacjaIn the paper a hybrid model of rotating beam is presented. It was obtained by using two methods: modal decomposition and spatial discretization. Reduced modal model was built for the system without the load related to inertia forces that occur during beam rotation. This inertia load was next modeled by using the method of simply spatial discretization and combined with reduced modal model. This approach allows to obtain accurate...
-
Modal analysis of railway current collectors using Autodesk Inventor
PublikacjaThe paper presents the results of modal analysis of railway current collector type 160EC. In the first place, the analysis was carried out analytically for a simplified two lumped mass pantograph model. Then numerical analysis was conducted in the Autodesk Inventor (AI) on the prepared multibody model using the AI modal analysis algorithm, which is based on the finite element method (FEM). Model elements which are most relevant...
-
Developing a cycling subsystem as part of a sustainable mobility strategy: the case of Gdansk
PublikacjaModal share is an important component in developing sustainable transport within a city. In recent years, many cities have set modal share targets for balanced and sustainable transport modes: 30% of public transport and 30% of non-motorized (cycling and walking) modes. Gdansk strategic documents have set similar goals with some actions already taken towards those goals. The cycle network is increasing popular. Gdansk’s cycling...
-
Hybrid, Approximate Models of Distributed-Parameter Systems
PublikacjaThe paper introduces the method of distributed-parameter systems modelling. It enables to obtain low order modal model of the system that experiences Coriolis acceleration component and gyroscopic effect. In such cases, corresponding system equations are non-self-adjoined. To solve this problem modal reduced model is built up for the system without Coriolis acceleration or gyroscopic effect terms. These phenomena are next included...
-
The Effect of University Campuses on the Modal Split of Polish Cities
PublikacjaThe article considers the effect Polish public universities have on the characteristics of urban traffic. The article describes how the public university community has changed over 25 years and its share in the urban population. The characteristics of the modal split in Polish university towns is given based on selected cases. The relation between the share of transport modes in the modal split and the size of towns or university...
-
Modelling and analysis of beam/bar structure by application of bond graphs
PublikacjaThe paper presents an uniform, port-based approach to modelling of beam/bar systems (trusses). Port-based model of such distributed parameter system has been defined by application of the bond graph methodology and the distributed transfer function method (DTFM). The proposed method of modelling enables to formulate input data for computer analysis by application of the DTFM. The constructed computational package enables the frequency...
-
Hybrid Model of Axially Moving Continua
PublikacjaThe paper introduces the method of the model reduction of systems that experience a Coriolis acceleration component. It causes that system equations are non-self-adjoined. To avoid such problem modal, reduced model is built up for the system without Coriolis acceleration terms which are next included by application of any lumping technique. Hence, the final reduced model is a hybrid one, obtained by both lumping and modal methods...
-
Hybrid model of geared rotor system
PublikacjaIn the paper a hybrid model of a geared multirotor system has been developed. The model is obtained by application of both the modal decomposition methodology and the spatial discretization method. Reduced modal model was constructed for the system without gyroscopic and damping effects. The gyroscopic interaction, damping and other phenomena which are difficult to include in the modal approach were modeled by application of simply...
-
Hybrid model of moving or rotating continua
PublikacjaThe paper introduces the method of the model reduction of systems that experience a Coriolis acceleration or gyroscopic effect component. In such causes that corresponding system equations are non-self-adjoined. Modal reduced model is built up for the system without Coriolis or gyroscopic effect terms. These phenomena are next included by application of any lumping technique. Hence, the final reduced model is a hybrid one, obtained...
-
Reduced order model of 2d system
PublikacjaA new method of modelling is developed for static and dynamic analysis of two-dimensional elastic bodies. In the analysis, an elastic body is divided into strips. For each one-dimensional strip the reduced modal model is build up. The modal model contains appropriate number of inputs and outputs to connect lumped interaction that occur between strips. Proposed method of modelling enables to obtain more accurate and more simple...
-
Effects of the Covid-19 travel restrictions on metropolises mobility: empirical evidence from the Tricity metropolis (Poland)
PublikacjaThis paper aims to assess changes in mobility and modal shift caused by COVID-19 travel restrictions among the residents of Gdańsk Bay Metropolis (Poland). Measurement’s moments were assumed in periods differing in the level of restric- tions. The computer-assisted telephone interview (CATI) was carried out in November and December 2020. The results did not confirm the expected modal shift. However, significant changes in the number...
-
Experimental study on plate modal parameters
PublikacjaTest doświadczalny jest częścią systemu diagnostycznego. Autorzy badają wpływ dodatkowej masy na parametry modalne wolno popartej stalowej płytyi. Artykół przedstawia technikę wyznaczania parametrów modalnych dla systemów monitorowania konstrukcji.The experimental test introduced in the paper is the part of the diagnostic system. The authors investigate the influence of the additional mass on modal parameters of simply supported...
-
Load Testing of GFRP Composite U-Shape Footbridge
PublikacjaThe paper presents the scope of load tests carried out on an innovative shell composite footbridge. The tested footbridge was manufactured in one production cycle and has no components made from materials other than GFRP laminates and PET foam. The load tests, performed on a 14-m long structure, were the final stage of a research program in the Fobridge project carried out in cooperation with: Gdańsk University of Technology (leader),...
-
Non-Destructive Diagnostics of Concrete Beams Strengthened with Steel Plates Using Modal Analysis and Wavelet Transform
PublikacjaExternally bonded reinforcements are commonly and widely used in civil engineering objects made of concrete to increase the structure load capacity or to minimize the negative effects of long-term operation and possible defects. The quality of adhesive bonding between a strengthened structure and steel or composite elements is essential for effective reinforcement; therefore, there is a need for non-destructive diagnostics of adhesive...
-
Numerical modal analysis of a vertical rising steel water gate
PublikacjaVertical rising steel water gates are very common not only in Poland and Germany but also in other countries of the world. Their popularity is mainly attributed to their simplicity of construction, which makes their production process cheaper and faster when compared to other solutions. The aim of this paper is to conduct a numerical modal analysis to examine the eigenvalues and eigenmodes of a vertical rising steel gate. Two cases...
-
Modelling method for a class of distributed-lumped parameter systems
PublikacjaThe paper presents an alternative approach for modelling and order reduction of continuous system. The proposed methodology combines application of two methods: the modal decomposition method and the rigid finite element method. The given continuous structure is divided into 1D continuous substructures. For each 1D substructure modal decomposition and reduction procedure is applied. Interactions between substructures are described...
-
Numerical Modelling of Structures with Uncertainties
PublikacjaThe nature of environmental interactions, as well as large dimensions and complex structure of marine offshore objects, make designing, building and operation of these objects a great challenge. This is the reason why a vast majority of investment cases of this type include structural analysis, performed using scaled laboratory models and complemented by extended computer simulations. The present paper focuses on FEM modelling...