Filtry
wszystkich: 1823
wybranych: 851
Wyniki wyszukiwania dla: CLAMPING DIAMETER
-
Design of Jack-up Platform for 6 MW Wind Turbine: Parametric Analysis Based Dimensioning of Platform Legs
PublikacjaThe article presents the results of the research conducted within the framework of the project entitled WIND-TU-PLA (ERA-NET, MARTEC II), the general aim of which was to design and analyse supporting structures for wind turbines intended for operation on the South Baltic area. The research part described in the article aimed at developing a preliminary design for a jack-up platform which can operate on water areas with depth of...
-
Displacement piles - classification and methods for the calculation of bearing capacity.
PublikacjaDisplacement piles belong to a group of technologies whose main idea is to install or make a pile without extracting ground material. According to definition, contained in PN-EN:1997-1:2008, displacement piles should be considered as driven, pressed in using vibrators and made with the use of spread augers. The classification of piles used so far with regard to the technology of execution is modified. An additional element is the...
-
Experimental study of flow boiling pressure drop and heat transfer of R1233zd(E) at moderate and high saturation temperatures
PublikacjaThe paper presents the results of experimental study of flow boiling of R1233zd(E) in minichannel at moderate and high saturation temperatures. The heat transfer coefficient and pressure drop were measured for flow boiling in a stainless steel tube with 2 mm inside diameter and a length of 300 mm. Experiment has been conducted for saturation temperatures ranging from 83 to 145 °C which corresponds to values of reduced pressures...
-
Objectivization of phonological evaluation of speech elements by means of audio parametrization
PublikacjaThis study addresses two issues related to both machine- and subjective-based speech evaluation by investigating five phonological phenomena related to allophone production. Its aim is to use objective parametrization and phonological classification of the recorded allophones. These allophones were selected as specifically difficult for Polish speakers of English: aspiration, final obstruent devoicing, dark lateral /l/, velar nasal...
-
A comprehensive survey on low-cost ECG acquisition systems: Advances on design specifications, challenges and future direction
PublikacjaAvailability of low-cost, reliable, and portable Electrocardiography (ECG) devices is still very important in the medical world today. Despite the tremendous technological advancement, Cardiovascular Diseases (CVDs) remain a serious health burden claiming millions of lives on an annual basis globally. This is more prevalent in Low and Middle-Income Countries (LMICs) where there are huge financial instability and lack of critical...
-
Deformable model of a butterfly in motion on the example of Attacus atlas
PublikacjaInsect wings can undergo significant chordwise (camber) as well as spanwise (twist) deformation during flapping flight but the effect of these deformations is not well understood. The shape and size of butterfly wings leads to particularly large wing deformations, making them an ideal test case for investigation of these effects. High-speed videogrammetry was used to capture the wing kinematics and deformations. The movements of...
-
Wykorzystanie algorytmów ewolucyjnych do doboru wzmocnień rozszerzonego obserwatora prędkości maszyny indukcyjnej
PublikacjaW pracy opisano sposób doboru wzmocnień rozszerzonego obserwatora prędkości maszyny indukcyjnej przy wykorzystaniu algorytmów ewolucyjnych. Zaproponowano funkcję celu opartą na rozkładzie biegunów obserwatora. Ze względu na wpływ prędkości maszyny na dynamikę obserwatora zaproponowano dobór wzmocnień obserwatora dla różnych przedziałów prędkości. Dla poszczególnych przedziałów zaprezentowano wyniki doboru wzmocnień w postaci tabel...
-
Comparative molecular dynamics study of dimeric and monomeric forms of HIV-1 protease in ligand bound and unbound state
PublikacjaHuman immunodeficiency virus type 1 protease (HIV-1 PR) is a viral-encoded enzyme that forms a homodimer. HIV-1 PR is essential for replication and assembly of the virus and inactivation of HIV-1 PR enzyme causes production of immature, noninfectious viral particles and thus HIV-1 PR is an attractive target in anti-AIDS drug design. In our current work, we performed molecular dynamics (MD) calculations (500 ns) for two different...
-
Magnetic anisotropy and structural flexibility in the f ield-induced single ion magnets [Co{(OPPh2) (EPPh2)N}2], E = S, Se, explored by experimental and computational methods
PublikacjaDuring the last few years, a large number of mononuclear Co(II) complexes of various coordination geometries have been explored as potential single ion magnets (SIMs). In the work presented herein, the Co(II) S = 3/2 tetrahedral [Co{(OPPh2)(EPPh2)N}2], E = S, Se, complexes (abbreviated as CoO2E2), bearing chalcogenated mixed donor-atom imidodiphosphinato ligands, were studied by both experimental and computational techniques. Specifically,...
-
Powikłania po rekonstrukcji piersi: problem zakażeń i strategii prewencyjnej - przegląd literaturowy
PublikacjaW niniejszej pracy przedstawiono dane dotyczące powikłań po rekonstrukcji piersi. Manuskrypt ma na celu usystematyzowanie wyników badań z ostatnich lat wraz z aspektami, takimi jak: częstotliwość występowania powikłań oraz ich rodzaj, czynniki predysponujące, a także możliwości profilaktyki. Przeanalizowano dane literaturowe z ogólnie dostępnych artykułów z okresu ostatnich pięciu lat, ze szczególnym uwzględnieniem zakażeń. Do...
-
The excitation controller with gain scheduling mechanism for synchronous generator control
PublikacjaThe power systems, including the synchronous generators and power systems networks, are complex nonlinear systems with configuration and parameters which change through time. That leads to electromechanical oscillations occurring in that system. Thus synchronous generator excitation controller must be capable of providing appropriate stabilization signal over broad range of operating conditions and disturbances. In this paper,...
-
Spectrum-based modal parameters identification with Particle Swarm Optimization
PublikacjaThe paper presents the new method of the natural frequencies and damping identification based on the Artificial Intelligence (AI) Particle Swarm Optimization (PSO) algorithm. The identification is performed in the frequency domain. The algorithm performs two PSO-based steps and introduces some modifications in order to achieve quick convergence and low estimation error of the identified parameters’ values for multi-mode systems....
-
Modern GFRP Composite Footbridges
PublikacjaApplication of GFRP composites in civil engineering is still not large but already noticeable. Advantages of this material, such as: low volume weight, relatively high stiffness and strength, well fatigue resistance, easiness in shaping, high material damping and high environmental resistance, make it attractive for bridge and in particular foot-bridge designers. It is estimated that nowadays in the world there are realized hundreds...
-
Photoelectrochemically Active N‐Adsorbing Ultrathin TiO2 Layers for Water‐Splitting Applications Prepared by Pyrolysis of Oleic Acid on Iron Oxide Nanoparticle Surfaces under Nitrogen Environment
PublikacjaHighly performing photocatalytic surfaces are nowadays highly desirable in energy fields, mainly due to their applicability as photo water‐splitting electrodes. One of the current challenges in this field is the production of highly controllable and efficient photoactive surfaces on many substrates. Atomic layer deposition has allowed the deposition of photoactive TiO2 layers over wide range of materials and surfaces. However,...
-
SIMULATION OF PROCEED® SURGICAL MESH APPLIED TO VENTRAL HERNIA REPAIR
PublikacjaIn the present research, Proceed® implant is considered. The system is subjected to short-time dynamic pressure load, similar to post-operative cough naturally occurring in human abdomen. The model refers to a clinical case of 5cm of hernia operated by Proceed implant fixed by 15 joints every 3cm around the orifice. The simulations of the implanted mesh are performed by means of the Finite Element Method. The implant is modelled...
-
Finite-element analysis of a base-isolated multi-storey steel building under seismic motions
PublikacjaNumerical simulation of the seismic behaviour of a multi-storey steel building, both fixed-base and base-isolated, under the 1940 El Centro earthquake was performed in this paper. The analyzed 4-storey building was decoupled from the shaking ground with the Polymeric Bearings, which can be considered a proposal of a new seismic isolation system. It consists of rectangular-shaped blocks made of a specially prepared flexible polymeric...
-
Initial Field Validation of Poroelastic Pavement Made with Crumb Rubber, Mineral Aggregate and Highly Polymer-Modified Bitumen
PublikacjaTire/road noise in most driving conditions dominates other sources of traffic noise. One of the most efficient ways of reducing tire/road noise is to use the so-called “low noise pavement”. According to numerous studies, at present, poroelastic road pavement that is composed of rubber and mineral aggregate and polyurethane or bituminous binder gives the best noise reduction up to 12 dB. Unfortunately, there are many problems with...
-
Microstructure and Mechanical Properties of Carboxylated Nitrile Butadiene Rubber/Epoxy/XNBR-grafted Halloysite Nanotubes Nanocomposites
PublikacjaThe effect of various amounts of carboxylated nitrile butadiene rubber (XNBR) functionalized halloysite nanotubes (XHNTs) on the cure characteristics, mechanical and swelling behavior of XNBR/epoxy compounds was experimentally and theoretically investigated. The morphology of the prepared XNBR/epoxy/XHNTs nanocomposites was imaged using scanning electron microscopy (SEM). The effects of various XNBR-grafted nanotubes on the damping...
-
Estimation of nonstructural stiffness in instrumented steel frames
PublikacjaLateral stiffness of nonstructural components may significantly influence the initial stiffness of the entire structure and consequently alter its dynamic characteristics. While methods for simulating structural members are well-established, approaches for modeling nonstructural components that also participate in seismic response are notably less developed. In this paper a simplified, physically-intuitive approach for estimating...
-
Novel Vision Monitoring Method Based on Multi Light Points for Space-Time Analysis of Overhead Contact Line Displacements
PublikacjaThe article presents an innovative vision monitoring method of overhead contact line (OCL) displacement, which utilizes a set of LED light points installed along it. A light point is an, LED fed from a battery. Displacements of the LED points, recorded by a camera, are interpreted as a change of OCL shape in time and space. The vision system comprises a camera, properly situated with respect to the OCL, which is capable of capturing...
-
Energy-Aware Scheduling for High-Performance Computing Systems: A Survey
PublikacjaHigh-performance computing (HPC), according to its name, is traditionally oriented toward performance, especially the execution time and scalability of the computations. However, due to the high cost and environmental issues, energy consumption has already become a very important factor that needs to be considered. The paper presents a survey of energy-aware scheduling methods used in a modern HPC environment, starting with the...
-
Experimental Study on Dynamics of Wooden House Wall Panels with Different Thermal Isolation
PublikacjaWood frame buildings are very popular in regions that are exposed to different dynamic excitations including earthquakes. Therefore, their seismic resistance is really important in order to prevent structural damages and human losses. The aim of the present paper is to show the results of experimental tests focused on the dynamic response of wall panels of a wooden frame building with thermal isolation made of mineral wool and...
-
Metodyka badań rozwojowych nowego typu silników i pomp satelitowych
PublikacjaResearch and development of new type satellite motors and satellite pumps SM with small geometrical displacement, from 5 to 73 cm3/rev, has been conducted in cooperation with Stosowanie Maszyn company from Katowice (manufacturer of motors and pump SM). The improvement of construction of those machines, especially construction of axial compensation and construction of fluid distribution channels have been the main problem of research...
-
Large hydrodynamic thrust bearing: Comparison of the calculations and measurements
PublikacjaHydrodynamic thrust bearings, used to carry axial loads in heavily loaded shafts of water power plants hydro turbines, can reach outer diameters even exceeding 5 m. In such large objects scale effect could be observed. According to this, allowable bearing specific load assuring safe operation of the bearings has to be decreased, which increases thrust bearing dimensions. This effect is caused by excessive thermal deflections of...
-
Water-Lubricated Sintered Bronze Journal Bearings—Theoretical and Experimental Research
PublikacjaWater lubricated bearings are used from many years in shipbuilding, hydro power and other industries because of their advantages such as: extensive serviceable life, low coefficient of friction, longevity of shaft sleeve, good abrasion resistance, low maintenance required, unit simplicity, no danger of pollution and low price. Various types of water lubricated sliding bearings have been tested at the Technical University of Gdansk...
-
Enhancing colloidal stability of nanodiamond via surface modification with dendritic molecules for optical sensing in physiological environments
PublikacjaPre-treatment of diamond surface in low-temperature plasma for oxygenation and in acids for carboxylation was hypothesized to promote the branching density of the hyperbranched glycidol polymer. This was expected to increase the homogeneity of the branching level and suppress interactions with proteins. As a result, composite nanodiamonds with reduced hydrodynamic diameters that are maintained in physiological environments were...
-
Selected aspects of two-phase flow studies using different visualization techniques in minichannels
PublikacjaThe subject of the study is to present the possibility of the use of visualization techniques in the researches on two-phase flows, carried out by the authors for many years. These works included as follows: heat transfer during the flow boiling, boiling crises and condensation in flow. The issue of the heat transfer intensification during the flow boiling through the channels of small diameters was analyzed. All this work focused...
-
Application of Feed Forward Neural Networks for Modeling of Heat Transfer Coefficient During Flow Condensation for Low and High Values of Saturation Temperatur
PublikacjaMost of the literature models for condensation heat transfer prediction are based on specific experimental parameters and are not general in nature for applications to fluids and non-experimental thermodynamic conditions. Nearly all correlations are created to predict data in normal HVAC conditions below 40°C. High temperature heat pumps operate at much higher parameters. This paper aims to create a general model for the calculation...
-
Bovine Serum Albumin – Hydroxyapatite Nanoflowers as Potential Local Drug Delivery System of Ciprofloxacin
PublikacjaIntroduction: Hybrid nanoflowers are structures consisting of organic (enzymes, proteins, nucleic acids) and inorganic components (mostly metal phosphates) with a flower-like hierarchical structure. Novel hybrid nanoflowers based on bovine serum albumin (BSA) and hydroxyapatite (HA) were obtained and characterized. Study on BSA-HA nanoflowers as potential drug delivery system is reported for the first time. Methods: Embedding ciprofloxacin...
-
Thermoplastic starch nanocomposites using cellulose-rich Chrysopogon zizanioides nanofibers
PublikacjaGreen thermoplastic starch (TPS) nanocomposite films aided by cellulose nanofibers (CNFs) from Chrysopogon zizanioides roots were developed and characterized. When compared to other lignocellulosic fibers, Chrysopogon zizanioides roots revealed exceptionally high cellulose content (~48%). CNFs were separated using an environmentally friendly acid isolation technique that included three stages: (i) alkali treatment; (ii) bleaching;...
-
Investigation of the Dynamism of Nanosized SOA Particle Formation in Indoor Air by a Scanning Mobility Particle Sizer and Proton-Transfer-Reaction Mass Spectrometry
PublikacjaTerpenes are VOCs of particular importance, since they are emitted from a wide range of indoor sources and are considered to be precursors of Secondary Organic Aerosol (SOA) formation. It has been proven that SOA particles, especially nanosized ones, pose a threat to human health. In this research, experiments with the application of an environmental chamber and real-time measurement techniques were carried out to investigate in...
-
Hybrid P3HT: PCBM/GaN nanowire/Si cascade heterojunction for photovoltaic application
PublikacjaPoly(3-hexylthiophene) (P3HT) and phenyl-C61-butyric acid methyl ester (PCBM) are commonly used for the fabrication of organic photovoltaics (OPV). Efficiency limitations of OPVs could be circumvented by incorporation of inorganic nanostructures into organic blends. Again, integration of organic solar cells with well-developed silicon photovoltaic technology is ultimately desirable. In present work, GaN nanowires with diameters...
-
Sulfur Driven Nucleation Mode Formation in Diesel Exhaust under Transient Driving Conditions
Publikacja -
Synthesis and characterization of ruthenium and rhenium dyes with phosphonate anchoring groups
PublikacjaRe(L1)–Re(L3), a series of rhenium(I) tricarbonyl chloride complexes with bpy-R2 derivatives L1–L3 (bpy = 2,2′-bipyridine, R represents the substitution at the 4- and 4′-positions), and their corresponding trishomoleptic Ru(L1)3–Ru(L3)3 as well as heteroleptic ruthenium(II) complexes Ru(tbbpy)2(L1) and Ru(tbbpy)2(L2) have been synthesized and characterized. Their applicability as immobilizable metal–organic chromophores in solar...
-
Inhibitors and Antibody Fragments as Potential Anti-Inflammatory Therapeutics Targeting Neutrophil Proteinase 3 in Human Disease
Publikacja -
Daily diet containing canned products significantly increases serum concentrations of endocrine disruptor bisphenol A in young women
PublikacjaNowadays, exposure to environmental factors is considered to be one of the possible causes of several lifestyle diseases, such as obesity, type 2 diabetes, cardiovascular disease, and cancer. Particularly noteworthy are endocrine‑disrupting chemicals (EDCs), which affect the metabolism of hormones and interact with their receptors, thus exerting adverse health effects. One of the most ubiquitous EDC in daily life is bisphenol A...
-
Analiza porównawcza procesów tłumienia i wygładzania fali ciśnienia w trakcie nieustalonego przepływu w rurociągach wykonanych z różnych materiałów.
PublikacjaUderzenie hydrauliczne jest uważane za jeden z najważniejszych problemów nieustalonego przepływu w przewodach, dlatego nadal stanowi obiekt badań wielu naukowców. To zagadnienie może być badane na dwóch poziomach: praktycznym i teoretycznym. W artykule zaprezentowane zostały wyniki badań doświadczalnych przeprowadzonych na stanowisku pomiarowym nieustalonego przepływu, funkcjonującym w Laboratorium Hydraulicznym Wydziału Inżynierii...
-
Modelling of subarachnoid space width changes in apnoea resulting as a function of blood flow parameters
PublikacjaDuring apnoea, the pial artery is subjected to two opposite physiological processes: vasoconstriction due to elevated blood pressure and vasorelaxation driven by rising pH in the brain parenchyma. We hypothesized that the pial artery response to apnoea may vary, depending on which process dominate. Apnoea experiments were performed in a group of 19 healthy, non-smoking volunteers (9 men and 10 women). The following parameters...
-
Organic Rankine cycle as bottoming cycle to a combined Brayton and Clausius - Rankine cycle
PublikacjaA preliminary evaluation has been made of a possibility of bottoming of a conventional Brayton cycle cooperating with the CHP power plant with the organic Rankine cycle installation. Such solution contributes to the possibility of annual operation of that power plant, except of operation only in periods when there is a demand for the heat. Additional benefit would be the fact that an optimized backpressure steam cycle has the advantage...
-
Electrophoretic deposition and characterization of composite chitosan/Eudragit E 100 or poly(4-vinylpyridine)/mesoporous bioactive glass nanoparticles coatings on pre-treated titanium for implant applications
PublikacjaTitanium implants are surface-modified to achieve bioactivity and often antibacterial properties. Such surface coatings may increase corrosion degradation and be weakly attached to the substrate. In the present research, biodegradable composite coatings, investigated so far as smart environment-sensitive, slowly releasing silver to the implant neighborhood, were produced as a combination of chitosan (CS) with Eudragit E 100 (EE100)...
-
The Impact of Isocyanate Index and Filler Functionalities on the Performance of Flexible Foamed Polyurethane/Ground Tire Rubber Composites
PublikacjaThe structure and performance of polyurethane (PU) foams are strongly driven by the stoichiometry of the polyaddition reaction, quantitatively described by the isocyanate index. It determines the balance between isocyanate and hydroxyl groups in the reacting system and is affected by the introduction of additional functionalities originated, e.g., from applied fillers. Nevertheless, this issue is hardly taken into account in research...
-
The geometry of free-standing titania nanotubes as a critical factor controlling their optical and photoelectrochemical performance
PublikacjaTitanium dioxide nanotubes are regarded as one of the most important functional materials and due to their unique electronic properties, chemical stability and photocorrosion resistance, they find applications in, for example, highly efficient photocatalysis or perovskite solar cells. Nevertheless, modification of TiO2 nanotubes is required to overcome their main drawback, i.e. large energy bandgap (>3.2 eV) limiting their ability...
-
Direct-contact condensation from vapour- gas mixture in a spray ejector condenser for negative CO2 power plant
PublikacjaDirect-contact condensation of vapour containing the inert gas on a spray of subcooled liquid exists in a number of technical applications. For example, it may be found in the nuclear industry (e.g. pressurized jet under normal operating conditions, in safety analyses) or in the chemical industry (e.g. mixing-type heat exchanger, degasser, sea water desalting). The problem is also essential to modelling and analysis of some...
-
Polypropylene structure alterations after 5 years of natural degradation in a waste landfill
PublikacjaUp to 25% of plastic waste in Europe is still disposed of in landfills, despite recycling efforts. The plastic waste in the landfill plot may be exposed both to abiotic and biotic degradation processes, although it is thought that most of the plastic materials tend to be resistant to biodegradation or biodeterioration even after a long time. To verify if polypropylene (PP) can undergo the process of short-term biodegradation and...
-
Utilization of oriented crystal growth for screening of aromatic carboxylic acids cocrystallization with urea
PublikacjaThe possibility of molecular complex formation in the solid state of urea with benzoic acid analogues was measured directly on the crystallite films deposited on the glass surface using powder X-ray diffractometry (PXRD). Obtained solid mixtures were also analyzed using Fourier transform infrared spectroscopy (FTIR). The simple droplet evaporation method was found to be efficient, robust, fast and cost-preserving approach for first...
-
Shaking table experimental study on damage mechanism of the disconnecting switch under seismic excitation
PublikacjaThe efficiency of the energetic network is a very import safety issue in the region experienced by the earthquake. High voltage disconnecting switches are important elements of the energetic infrastructure used to separate electric circuits (i.e. during repairs), which should not be damaged remaining fully operational. The aim of the paper is to show the results of the shaking table experimental investigation focused on damage...
-
Curing epoxy with ethylenediaminetetraacetic acid (EDTA) surface-functionalized Co Fe3-O4 magnetic nanoparticles
PublikacjaIn this work, the bulk and surface composition of Fe3O4 supermagnetic nanoparticles were modified for efficient epoxy curing. The bare, ethylenediaminetetraacetic acid (EDTA) capped, and cobalt (Co)-doped EDTA capped Fe3O4 nanoparticles were synthesized electrochemically. The crystalline structure and phase information, surface capping, morphology and magnetization behavior of nanoparticles were studied by X-Ray diffraction (XRD),...
-
Generation and Propagation of Nonlinear Waves in a Towing Tank
PublikacjaThe paper presents the results of the research focused on linear and nonlinear wave generation and propagation in a deepwater towing tank equipped with a single flap-type wavemaker of variable draft. The problem of wave generation and propagation has been theoretically formulated and solved by applying an analytical method; linear and nonlinear solutions were obtained. The linear solution has been verified experimentally. The...
-
Thermal and technological aspects of double face grinding of Al2O3 ceramic materials
PublikacjaDouble face grinding with planetary kinematics is a process to manufacture workpieces with plan parallel functional surfaces, such as bearing rings or sealing shims. In order to increase the economic efficiency of this process, it has to be advanced permanently. The temperature in the contact zone of most grinding processes has a huge influence on the process efficiency and the workpiece qualities. In contrast to most grinding...
-
Dynamic modeling of non-cylindrical curved viscoelastic single-walled carbon nanotubes based on the second gradient theory
PublikacjaThis paper is devoted to the theoretical study of the dynamic response of non-cylindrical curved viscoelastic single-walled carbon nanotubes (SWCNTs). The curved nanotubes are largely used in many engineering applications, but it is challenging in understanding mechanically the dynamic response of these curved SWCNTs when considering the influences of the material viscosity. The viscoelastic damping effect on the dynamic response...