Filtry
wszystkich: 4159
wybranych: 3843
-
Katalog
- Publikacje 3843 wyników po odfiltrowaniu
- Czasopisma 23 wyników po odfiltrowaniu
- Konferencje 2 wyników po odfiltrowaniu
- Osoby 46 wyników po odfiltrowaniu
- Wynalazki 3 wyników po odfiltrowaniu
- Projekty 1 wyników po odfiltrowaniu
- Kursy Online 17 wyników po odfiltrowaniu
- Wydarzenia 2 wyników po odfiltrowaniu
- Dane Badawcze 222 wyników po odfiltrowaniu
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: bearings defects
-
Experimental research on marine oil-lubricated stern tube bearing
PublikacjaBearings of propeller shafts are very crucial elements of the propulsion system of each of the ships. The safety of shipping depends on their durability and reliability. The new legal restrictions mean that today we are looking for environmentally friendly solutions. That is why water-lubricated bearings are becoming more and more popular. So, will oil-lubricated shaft bearings belong to the past? The bearing with a white metal...
-
Influence of an applied bearing system on behaviour of multi-span footbridge
PublikacjaThe cycle overpass in Gdynia is a box structure over 300 metres long, 10-span. It was opened for bicycle traffic in the second half of 2013. At the end of its construction, there was failure due to excessive horizontal displacement of the system. A number of bearings exceeded the range of permissible transverse shifts thus it was necessary to temporarily protect the spans from slipping. The FEM analysis of the original solution...
-
Assessment of the Effectiveness of a Short-term Hearing Aid Use in Patients with Different Degrees of Hearing Loss
PublikacjaThe study presents evaluating the effectiveness of the hearing aid fitting process in the short-term use (7 days). The evaluation method consists of a survey based on the APHAB (Abbreviated Profile of Hearing Aid Benefit) questionnaire. Additional criteria such as a degree of hearing loss, number of hours and days of hearing aid use as well as the user’s experience were also taken into consideration. The outcomes of the benefit...
-
Comparison of the characteristics of journal bearings determined according to ISO 7902:2020 and obtained by other methods
PublikacjaThe article presents selected characteristics of journal bearings calculated with the use of various methods and compared to the results obtained with application of the basic bearing characteristics calculation procedure, as described in the ISO 7902:2020 standard. Additionally, the presented calculation results were compared with the parameters measured during experimental tests of the sliding bearings, working under loads and...
-
Comparable analysis of PID controller settings in order to ensure reliable operation of active foil bearings
PublikacjaIn comparison to the traditional solutions, active bearings offer great operating flexibility, ensure better operating conditions over a wider range of rotational speeds and are safe to use. In order to ensure optimum bearing performance a bearing control system is used that adapts different geometries during device operation. The selection of optimal controller parameters requires the use of modern optimization methods that make...
-
Marine propeller shaft bearings under low-speed conditions: water vs. oil lubrication
PublikacjaThe bearings used in shipbuilding, hydropower, and water pumps have undergone a metamorphosis in recent decades. Because of environmental regulations, lubrication with grease or mineral oil is prohibited. Thus, the standard solutions include water-lubricated bearings with polymer bushings or sealed systems lubricated with oil. When properly designed, assembled, and operated, bearings can operate reliably for years. However, specific...
-
WATER LUBRICATED MAIN SHAFT BEARINGS - MODERN SOLUTION FOR HYDROPOWER INDUSTRY - Experimental and theoretical studies
PublikacjaWater-lubricated bearings are finding increasingly wide use in various branches of industry. As such, they may also be encountered in hydro power industry. They are also increasingly frequently employed in bearing systems of marine shaft propulsions and water pumps [1]. This rising popularity is due to a number of reasons [2]. First of all, their simple construction has direct impact on the level of pricing which is usually quite...
-
Shaft Misalignment Influence on Water Lubricated Turbine Sliding Bearings with Various Bush Modules of Elasticity
PublikacjaW artykule przeanalizowano wpływ wielkości przenoszenia osi wału względem panwi na nośność łożyska. Analizie poddano łożyska z odmiennymi rodzajami panwi o różnej sztywności.
-
Numeryczna analiza trójwymiarowego przepływu w polimerowym łożysku smarowanym wodą = Numerical analysis of three dimensional flow in water lubricated bearing with polymer bearing bush
PublikacjaW referacie przedstawiono wyniki obliczeń łożysk smarowanych wodą w oparciu o metodę CFD - obliczeniowej mechaniki płynów. Wykazano przydatność nowoczesnych narzędzi obliczeniowych do rozwiązywania podobnych problemów.
-
Research on water lubricated main shaft bearings in conditions of improper lubrication and cooling conducted on high torque real-life scale bush test rig
PublikacjaWater lubricated polymer bushes find increasingly popular use in the sliding bearings of marine propellers, water turbines and pump shafts. Such popularity is partly due to their simple construction which also means relatively affordable price. In addition, properly designed and installed water lubricated bearings may well last for over a decade. However, in practical experience one may also observe cases of rapid wear...
-
Employing economical methods for pavement defects estimation
PublikacjaIt is a common practise that measurements of road surface conditions are made using professional and expensive apparatus. Typically a van or a truck equipped with a set of professional sensors i.e. laser scanners of surface is used, therefore the measurement update period is often quite long. Two alternative low-cost methods for estimating road pavement defects and failures were proposed and investigated by the authors. The first...
-
Technology of welding hard wearing plates
Publikacja -
Contactless hearing aid designed for infants
PublikacjaIt is a well known fact that language development through home intervention for a hearing-impaired infant should start in the early months of a newborn baby's life. The aim of this paper is to present a concept of a contactless digital hearing aid designed especially for infants. In contrast to all typical wearable hearing aid solutions (ITC, ITE, BTE), the proposed device is mounted in the infant's bed with any parts of its set-up...
-
Special hearing aid for stuttering people
PublikacjaDzięku postępowi w dziedzienie cyfrowego przetwarzania sygnałów możliwe stało zbudowanie subminiaturowego urządzenia łączącego funkcje aparatu słuchowego i korektora mowy. Takie urządzenie, mimo niewielkich rozmiarów, jest w stanie wykonywać skomplikowane alggorytmy a jego oprogramowanie może być łatwo zmieniane. W pracy skupiono się na zagadnieniach związanych z opracowniem prototypu i implementacją algorytmów korekcji słuchu...
-
Hearing and stomatognathic system: Searching for a link
Publikacja -
Evaluating the Hearing of Patients with Pseudoexfoliation Syndrome
Publikacja -
Wear measurements of self-lubricating bearing materials in small oscillatory movement
Publikacja -
Bearing current path and pulse rate in PWM-inverter-fed induction
Publikacja -
Neon-Bearing Ammonium Metal Formates: Formation and Behaviour under Pressure
Publikacja -
"FEM Parametric Study on Ultimate Bearing Capacity of CFST Arch Bridge
Publikacja -
Determination of the bearing capacity of pile foundations based on CPT test results
PublikacjaAnalityczne określanie pełnej krzywej obciążenie - osiadanie na podstawie parametrów geotechnicznych wciąż stanowi bardzo trudne zadanie naukowe i inżynierskie. W pracy przedstawiono metodę bezpośredniego wykorzystania oporów na stożku sondy statycznej do określania pełnej krzywej osiadania dla pali Vibro-Fundex. W sumie jako materiał weryfikacyjny wykorzystano 94 próbne obciążenia statyczne pali.
-
Use of Neural Networks in Diagnostics of Rolling-Element Bearing of the Induction Motor
Publikacja -
Improving of Cherry Fruit Quality and Bearing Regularity by Chemical Thinning with Fertilizer
Publikacja -
Effect of Coating Material Properties on Tilting-pad Thrust Bearing Performance
PublikacjaPolymer lined tilting-pad bearings demonstrate many advantages over traditional bearing systems. Bearings with a polymer layer in comparison with a babbitted layer show, for example: lower value of friction coefficient (important during start/stops), higher fatigue strength of the coating, better distribution of the load on individual pads due to lower elasticity of the polymers, wider range of operational temperatures or the ability...
-
Problems of analytical determination of journal bearing bush fatigue strength estimates
PublikacjaProblems connected with determination of stress distribution in sliding layer of thinwalled bearing bushes, investigated in bearing fatigue test rigs, have been presented. Using an example of plain bearings tested in the fatigue machine SMOK (built at the Gdask University of Technology) problems with obtaining a convergence of iterative procedure for determining the fatigue strength estimators of bearing alloy surface layer are...
-
Stochastic model for turbulent lubrication of slide journal bearing in ship technology.
PublikacjaTurbulentny przepływ smarujący ma zastosowanie w obliczeniach praktycznych siły nośnej poprzecznego łożyska ślizgowego dla wysokich prędkości obrotowych przy liczbach Taylora przekraczających wartość 41,2 względnie przy zmodyfikowanych liczbach Reynoldsa o wartościach Re[psi]=2. Główne wyniki pracy koncentrują się na wykazaniu zmian wartości ciśnienia i siły nośnej poprzecznego łożyska ślizgowego w przypadku turbulentnego, izotemicznego...
-
Metallochromic crown ether analogs bearing aromatic residues and azo groupings
PublikacjaPraca zawiera przegląd syntezowanych, różnych chromogenicznych związków koronowych, zawierających oprócz dwóch grup azowych i łańcucha polieterowego fragmenty heterocykliczne. Porównano właściwości otrzymanych związków w zależności od obecności heteroatomów w pierścieniu makrocyklicznym oraz różnego podstawienia cząsteczki heterocykliczej.
-
Pyrrole bearing diazocrowns: Selective chromoionophores for lead(II) optical sensing
PublikacjaDiazocrowns of 18-, 21- and 23-membered rings with pyrrole residue as a part of macrocycle were for the first time used as chromoionophores in lead(II) selective optodes. Sensing properties of optodes depend on the type of macrocycle, namely its size and the type of linker: oligoether or hydrocarbon chain. The best results were obtained for optode bearing 18-membered crown with oligoether linker showing linear response range of...
-
Estimation of Screw Displacement Pile-Bearing Capacity Based on Drilling Resistances
PublikacjaThis article presents an engineering, empiricalmethod of estimating the bearing capacity and settlementcharacteristics Q-s of screw displacement piles andcolumns, based on soil resistance encountered during thedrilling to form piles/columns in the ground. The methodwas developed on the basis of correlation analyses of thetest results of 24 piles made during the “DPDT-Auger”research project (Krasiński et al., 2022a). In the proposedmethod,...
-
Wear measurements of self lubricating bearing materials in small oscillatory movement
PublikacjaRosnące wymagania ekologiczne powodują wzrost tendencji wymiany klasycznych materiałów łożyskowych, wymagających dodatkowego czynnika smarnego, na materiały nie wymagające smarowania. Zamianie takiej może towarzyszyć obniżenie trwałości zmodernizowanego łożyska. Ten niekorzystny efekt nierzadko obserwuje się w węzłach łożyskowych kierownic turbin wodnych. Autorzy podjęli próbę wyjaśnienia zjawisk występujących w tego typu łożyskach....
-
The use of GFRP tubes as load-bearing jackets in concrete-composite columns
PublikacjaThe paper presents the fields of applications of polymer composites in building structures. The use of composite glass fibre tubes is discussed in more detail. The laboratory methods used to test the mechanical properties of these pipes are presented. An original research program is presented, including six concrete-filled glass fibre tubes. The cylinders and columns made in this way were tested for their axial load capacity. Conclusions...
-
Bearing capacity of working platform using distinct layout optimization method
PublikacjaBearing capacity of the working platforms from sandy soil resting on NC and OC clays was analyzed using LimitState GEO program. Different failure modes are considered using distinct layout optimization (DLO) method, which forms the upper bound solution of limit state analysis. Different mechanisms of failure were observed as a function of the platform thickness, angle of internal friction of the platform material and undrained...
-
Analysis of Failures of High Speed Shaft Bearing System in a Wind Turbine
PublikacjaDuring the operation of wind turbines with gearbox of traditional configuration, consisting of one planetary stage and two helical stages high failure rate of high speed shaft bearings is observed. Such a high failures frequency is not reflected in the results of standard calculations of bearing durability. Most probably it can be attributed to atypical failure mechanism. The authors studied problems in 1.5 MW wind turbines of...
-
Bearing estimation using double frequency reassignment for a linear passive array
PublikacjaThe paper demonstrates the use of frequency reassignment for bearing estimation. For this task, signals derived from a linear equispaced passive array are used. The presented method makes use of Fourier transformation based spatial spectrum estimation. It is further developed through the application of two-dimensional reassignment, which leads to obtaining highly concentrated energy distributions in the joint frequency-angle domain...
-
Evaluation of expanded uncertainty of instantaneous power measurement in a bearing diagnostic system.
PublikacjaThe paper presents the issues concerning the estimation of the expanded uncertainty in the system for the diagnosis of rolling bearings, consisting of transducers: voltage and current voltage, which is used for diagnostic bearing motors method based on the measurement and analysis of the instantaneous power signal consumed by the induction motor. It presents the methodology for assessing the measurement uncertainty and presents...
-
ANALYSIS OF THE POSSIBILITIES OF HIGH SPEED SHAFT BEARING SYSTEM DURABILITY INCREASE
PublikacjaDuring the operation of wind turbines with a gearbox of traditional configuration, a high failure rate of high-speed shaft bearings is observed. Such a high failures frequency is not reflected in standard bearing durability calculation methods, which can be attributed to atypical failure mechanism. To avoid observed problems in the 1.5 MW wind turbine, the modification of the existing bearing system is proposed. Multiple options,...
-
Fatigue resistance investigation of the IC engine MB11 bearings, working under conditions of dynamic unidirectional loadings
PublikacjaThe slide bearing material MB11 fatigue resistance has been investigated with the application of SMOK - test stand in which dynamic unidirectional loadings to the test bearing is generated. Slide bearing layer consists of the bronze MB11 ( Cu Pb22 Sn 3 ) sintered to the steel shell. Each of the tested bearing has been subject to the standard 20-hour test, under conditions of the full fluid lubrication. Methodology of the experiments,...
-
POSSIBILITY OF IDENTIFICATION OF TECHNICAL CONDITION OF BEARINGS FOR SELF-IGNITION ENGINES BY APPLICATION OF ACOUSTIC EMISSION AS A DIAGNOSTIC SIGNAL
PublikacjaThis paper presents the results of empirical studies where the acoustic emission (AE) method was applied to identify the technical condition of sliding surfaces of main and crank bearings for main diesel engines. The test results indicate that the measurements of the AE parameters allow the technical condition identification for bearings of this type. The results refer to the measurements of the parameters for AE generated in the...
-
Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction
PublikacjaIn hydrodynamic bearings traditional bearing alloys: Babbitts and bronzes are most frequently utilized. Polymer sliding layers are sometimes applied as a valuable alternative. Hard diamond-like carbon (DLC) coatings, which are also considered for certain applications may show some advantages, as well. Although material selection is of secondary importance in a full film lubrication regime it becomes important in mixed friction...
-
Effectiveness of a mathematical model in simulating nonlinear mechanical behaviour of a seismic isolation system made of polymeric bearings
PublikacjaThe present study was focused on determining the effectives of a nonlinear mathematical model in simulating complex mechanical behaviour of a seismic isolation system made of Polymeric Bearings. The proposed mathematical model defines the lateral force as a nonlinear function of the shear displacement and the deformation velocity. The effectiveness of the proposed mathematical model was verified by comparing the seismic response...
-
Evaluation of apparent Young׳s modulus of the composite polymer layers used as sliding surfaces in hydrodynamic thrust bearings
PublikacjaHydrodynamic bearings with a polymer sliding layer are able to operate in severe conditions, mainly due to favorable properties of the polymers. The goal of this research was to evaluate apparent Young׳s modulus of two types of the polymer composite layers used for sliding surfaces in hydrodynamic bearings, as a function of temperature. The Young׳s modulus was evaluated on the basis of compression tests carried out on samples obtained...
-
Sliding bearings with sintered bronze bush lubricated by contaminated water with solid particles – Theoretical and experimental studies
PublikacjaSliding journal bearings lubricated with water coming directly from the environment are a solution used in shipbuilding, pumps and hydropower. However, the working fluid or surrounding water cannot always be filtered because of design limitations, which often causes the problem of premature wear of these sensitive bearings. The research conducted made it possible to assess the wear of sliding bearings lubricated with water containing...
-
Pipeline geometry defects in high resolution pig's data
PublikacjaMost of the pipelines have been inspected at least once using intelligent pigging. The problem of specific software for interactive presentation, analysis and comparison of features revealed during the consecutive geometry surveys is emphasized. Capabilities of a simultaneous measurement of internal geometry and metal loss features in a single run are illustrated. Advantages of application of statistical characteristics of both...
-
Tool support for detecting defects in object-oriented models
PublikacjaArtykuł przedstawia nową metodę analityczną UML-HAZOP oraz narzędzie wspomagające jej stosowanie. Metoda ukierunkowana jest na wykrywanie defektów we wczesnych fazach wytwarzania oprogramowania i koncentruje się na powszechnie stosowanych modelach opartych na metodyce obiektowej.
-
Surface layer defects on injection-molded plastic components
PublikacjaProces wtryskiwania jakkolwiek jest powszechnie stosowany w przemyśle nie jest jeszcze do końca przebadany. W pracy przedstawiono model i symulację numeryczna procesu wtryskiwania wykonaną na bazie programu FIDAP. Na tej podstawie przedstawiono proces zachowania się tworzywa podczas procesu wtryskiwania w strefie przyściennej formy. Wyniki z symulacji porównano z danymi ekspermentalnymi.
-
Intelligent microbearing project with memory of stress-strain history
PublikacjaTaking into account the increasing need of intelligent micro-bearing with memory, this paper presents the optimization, simulation and practical application of operating parameters(load carrying capacity, friction forces, friction coefficient, wear), simulation for hydrodynamic HDD micro-bearing with curvilinear nano-grooved journal profile. One of the reason of such journal profile is that this journal profile contributes to the...
-
On the effectiveness of Ni alloy-bronze composite lattice structures used in slide bearings operated under heavy loads
Publikacja -
INFLUENCE OF SOLID PARTICLE CONTAMINATION ON THE WEAR PROCESS IN WATER LUBRICATED MARINE STRUT BEARINGS WITH NBR AND PTFE BUSHES
PublikacjaThis paper reports on a study of the influence of solid particle contamination on the wear process in water-lubricated slide bearings (steel-acrylonitrile-butadiene rubber (NBR) and steel- polytetrafluoroethylene (PTFE)). To compare the wear of the shaft journal and bushes (NBR and PTFE) when lubricated with fresh water and contaminated water, an experiment was carried out to identify key factors that influence the state of wear...
-
The Experimental Determination of Bearings Dynamic Coefficients in a Wide Range of Rotational Speeds, Taking into Account the Resonance and Hydrodynamic Instability
PublikacjaMethods for the experimental determination of dynamic coefficients are commonly used for the analysis of various types of bearings, including hydrodynamic, aerodynamic and foil bearings. There are currently several algorithms that allow estimating bearing dynamic coefficients. Such algorithms usually use various excitation techniques applied to rotor–bearings systems. So far only a small number of scientific publications show how...
-
Aromatic Dendrimers Bearing 2,4,6-Triphenyl-1,3,5-triazine Cores and Their Photocatalytic Performance
Publikacja