Filtry
wszystkich: 1332
wybranych: 1142
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: AUSTENITIC STEEL
-
Problems of strength modelling of steel sandwich panels under in-plate load
PublikacjaW pracy omówiono zagadnienia wytrzymałości statycznej stalowych paneli typu sandwich spawanych laserowo. Omówiono charakterystyki sztywności podczas zginania, przedstawiono zachowanie pod obciążeniem równomiernie rozłożonym a także sposób niszczenia pod obciążeniem ściskającym. Omówiono możliwości stosowania takich konstrukcji na podstawie wniosków z badań.
-
Hydrogen induced degradation of structural steel exposed to the technical liquid hydrocarbons
PublikacjaBadano degradacje stali 26H2MF w mieszaninach węglowodorów. Badania były prowadzone pod stałym obciążeniem i przy małej prędkości 10-6s-1
-
Interlayer defect evolution in an coating system on steel under hydromechanical loading
PublikacjaZaprezentowano wyniki pomiarów impedancyjnych obszaru międzywarstwowego w systemie powłokowym poddanym naprężeniom. Przedstawiono nowy sensor który jest zdolny do detekcji defektów w obszarze międzywarstwowym. Dwuwarstwowy system powłokowy przeznacziony do zastosowań morskich zbadano w celu określenia jego odporności na oddziaływanie cyklicznych naprężeń i zanurzeń w 3% roztworze NaCl.
-
Diagnosis of Damage in a Steel Tank Model by Shaking Table Harmonic Tests
PublikacjaThe aim of the present paper is to show the results of the shaking table experimental study concerning the diagnosis of damage in a model of cylindrical steel tank with self-supported roof which is filled with liquid. During the tests, the base of the structure was excited under the harmonic loading with variable frequency. The tests were repeated for different stages of damage, which was introduced in the model by easing the bolts...
-
Hydrogen effects in duplex stainless steel welded joints - electrochemical studies
PublikacjaIn this work results on the influence of hydrogen on passivity and corrosion resistance of 2205 duplex stainless steel (DSS) welded joints are described. The results were discussed by taking into account three different areas on the welded joint: weld metal (WM), heat-affected zone (HAZ) and parent metal. The corrosion resistance was qualified with the polarization curves registered in a synthetic sea water. The conclusion is that,...
-
Surface roughness analysis of hardened steel after high‐speed milling
Publikacja -
The influence of antiwear additive concentration on the tribological behaviour of a-C:H:W/steel tribosystem
Publikacja -
Elastic wave propagation for condition assessment of steel bar embedded in mortar
PublikacjaThis study deals with experimental and numerical investigations of elastic wave propagation in steel bars partially embedded in mortar. The bars with different bonding lengths were tested. Two types of damage were considered: damage of the steel bar and damage of the mortar. Longitudinal waves were excited by a piezoelectric actuator and a vibrometer was used to non-contact measurements of velocity signals. Numerical calculations...
-
Reduction of vibrations of steel structure models with Polymeric Bearings - experimental study
PublikacjaEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Therefore, designing earthquake protective systems has become an extremely challenging problem in civil engineering. Base isolation is one of the most popular and widely adopted methods of protecting structures against earthquake forces. The present paper reports the results obtained from the shaking table experimental...
-
Problems of collisions between adjacent steel structures under earthquake excitation
PublikacjaNowadays, the high level of urbanization forces the designers to design closely-separated structures and to take into account many factors influencing the response of these structures, which may collide due to insufficient separation distance during moderate to strong ground motions. Recent observations as well as numerical and experimental investigations have confirmed that the interactions between structures may lead to significant...
-
Ceria Based Protective Coatings for Steel Interconnects Prepared by Spray Pyrolysis
PublikacjaStainless steels can be used in solid oxide fuel/electrolysis stacks as interconnects. For successful long term operation they require protective coatings, that lower the corrosion rate and block chemical reactions between the interconnect and adjacent layers of the oxygen or the hydrogen electrode. One of the promising coating materials for the hydrogen side is ceria. Using standard sintering techniques, ceria sinters at around...
-
Fatigue behaviour of SLM maraging steel under variable-amplitude loading
PublikacjaOne of the most challenging issues for additive manufactured materials is fatigue endurance. Engineering components often operate under complex, variable amplitude loadings, in which existing technological imperfections promote fatigue cracks growth and damage of elements eventually. In this study the effects of different variable-amplitude strain levels on fatigue life, 18Ni300 steel was tested. The work presents various behaviours...
-
Nondestructive Characterization of 2CR-1Mo Steel Quality Using Magnetoacousting Emission
PublikacjaPrzedstawiono wyniki badań własności emisji magneto-akustycznej (EMA) oraz własności magnetycznych (pętla histerezy magnetycznej, efekt Barkhausena, magnetostrykcja) dla wycinków rur stali 2Cr-1Mo o różnym stopniu degradacji. Wykazano, iż początkowy etap degradacji skutkuje w obniżeniu natężenia EMA oraz magnetostrykcja także niewielką zmianą pola koercji i nie monotoniczną zmianą natężenia efektu Barkhausena).
-
Investigation of pitting corrosion of stainless steel by means of acousticemission and potentiodynamic methods.
PublikacjaPrzedstawiono wyniki badań korozji wżerowej przy jednoczesnym wykorzystaniu techniki potencjodynamicznej i emisji akustycznej. Dystrybuanta rozkładu prawdopodobieństwa wystąpienia korozji wżerowej (CDFp) została uzyskana na podstawie badań potencjodynamicznych. Niezależnie z wyników akustycznych otrzymano dystrybuantę rozkładu zdarzeń akustycznych (CDFae). Na podstawie wyników stwierdzono brak korelacji miedzy wynikami potencjodynamicznymi...
-
Influence of microstructure on properties of 18Cr-10Ni-Ti stainless steel products.
PublikacjaBadano wpływ mikrostruktury na właściwości mechaniczne i odporność korozyjną wyrobów ze stali austenitycznej 18Cr-10Ni-Ti po przesycaniu z temperatury 1050 C. Wykazano, że węgliki TiC w ziarnach i na granicach ziaren/bliźniaków powodują znaczne obniżenie wydłużenia stali. Węgliki TiC na granicach ziaren/bliźniaków obniżają odporność na korozję międzykrystaliczną i sprzyjają powstawaniu uszkodzeń korozyjnych podczas hutniczej operacji...
-
Research on deformations of laser-welded joint of a steel sandwich structure model.
PublikacjaPrzedstawiono problemy związane z zachowaniem złącza laserowego pod obciążeniem zginającym. Pokazano wyniki badań laboratoryjnych dla określenia mechanizmu pracy złącza i przedyskutowano uzyskane rezultaty.
-
Hydrogen assisted cracking of high-strength weldable steel in sea-water.
PublikacjaOceniono niszczenie wodorowe stali o wysokiej wytrzymałości i jej złączy spawanych przy różnych rodzajach obciążenia w wodzie morskiej. Przeprowadzono próby rozciągania z małą prędkością odkształcenia i zmęczenia niskocyklowego w wodzie morskiej przy polaryzacji katodowej. Badano stal gatunku 17HMBVA o minimalnej granicy plasyczności 690 MPa oraz jej złącza spawane automatycznie łukiem krytym i ręcznie łukowo elektrodą otuloną.
-
Influence of polyaniline primer on the corrosion properties of St3S steel - coating system
PublikacjaPraca przedstawia wyniki badań wpływu podkładu z polianiliny osadzonej elektrochemicznie na właściwości antykorozyjne powłoki epoksydowej na stali niskowęglowej St3S. Wykonano badania próbek nieuszkodzonych, a także próbek ze sztucznym defektem powłoki. Próbki były eksponowane na środowisko korozyjne przez 63 dni i były sukcesywnie badane za pomocą elektrochemicznej spektroskopii impedancyjnej. Postępy korozji były również oceniane...
-
The influence of the welding thermal cycles on corrosion resistance of duplex stainless steel
PublikacjaBadano skłonnośc strefy wpływu ciepła spoin ze stali dupleks do korozyjnego pękania narężeniowego. Wykonano próby korozyjne z wykorzystaniem metody SSRT w środowisku korozyjnym wrzącego MgCl2. Wykazano, że duży udział ferrytu w strukturze SWC pogarsza odpornośc na korozję. Badania metalograficzne na mikroskopie lektronowym wykazały różne sposoby propagacji pęknięcia zależnie od zawartości austenitu w strukturze SWC.
-
Relation between steel microstructure and its properties in inert and aggressive environments
PublikacjaBadano stale 26H2MF i 34HNM poddane różnej obróbce cieplnej. Mikrostruktury stali zmieniały sie od martenzytu i bainitu do odpuszczonego martenzytu i sorbitu. Obserwowano spadek energii zniszczenia, wydłużenia i przewżenia w próbie rozciągania z małą prędkością i równoczesnej polaryzacji katodowej do 100 mA/cm2. Degradacji towarzyszyła zmiana przełomu z ciągliwego na kruchy łupliwy i quasiłupliwy.
-
Hydrogen induced degradation of structural steel exposed to the technical liquid hydrocarbons
PublikacjaSusceptibility of the differently heat treated 26H2MF steel to stress corrosion cracking has been evaluated in the constant strain rate tension tests done at the strain rate 10-6s-1 and in the constant load tests done at the 0,98 of fracture load. The boiler fuel and the aged mineral oil at 135C and 80C respectively, have been used as the aggressive environments.
-
Mechanism of hydrogen enhanced-cracking of high-strength steel welded joints
PublikacjaPrzedstawiono badania podatności stali spawalnej o wysokiej wytrzymałości S690Q i jej złączy spawanych na niszczenie wodorowe w środowisku wody morskiej przy polaryzacji katodowej. Na podstawie wyników próby rozciągania z małą prędkością odkształcania i obserwacji przełomów próbek na SEM wskazano mechanizm pękania wspomaganego wodorem badanej stali i złączy spawanych.
-
Comparative buckling analysis of cylindrical steel silos with flat or corrugated sheets
PublikacjaW artykule zaprezentowano wyniki analizy wyboczeniowej cylindrycznych silosów wypełnionych materiałem sypkim wykonanych z blachy falistej usztywnionego słupami oraz z blachy płaskiej. Wykonano nieliniową analizę statyczną całego silosu z uwzględnieniem wstępnych imperfekcji geometrycznych przy zastosowaniu różnych przestrzennych modeli numerycznych MES. Wyniki analiza pokazują, że silosy z blachy falistej są bezpieczniejsze i bardziej...
-
Report no: WOiO /II/46/2015 - Construction node verification test, estimation of breaking load (shear force) and destruction form
PublikacjaA new generation of tanks for LNG transportation has been designed. Mass reduction forced our customer to use three different materials: austenitic steel, aluminium alloy and LNG compressed wood between them. The expertise concerns structural node between tank foundation and suspension. Expertise contains: description of object of test, test principals, results and conclusions
-
Aspects of intergranular corrosion of AISI 321 stainless steel in high-carbon-containing environments
PublikacjaPurpose – The purpose of this paper is to present a case study of unexpected sensitization to intergranular corrosion of highly resistant AISI 321 steel in petrochemical conditions, where it was subjected to the simultaneous influence of elevated temperature of 250°C and vapors from the asphalt production process. Design/methodology/approach – Corrosion coupons were exposed in an installation carrying asphalt vapors. To identify...
-
Determination of t8/5 cooling times for underwater local dry welding of steel
PublikacjaKnowledge of thermal history is the basic condition for studying the structure - properties of welded joints. The determinant of thermal history is the thermal cycle, whose in-situ measurements are still a big challenge. Water as the welding environment complicates this issue even more. The article presents a method to determine an equation for calculating t8/5 cooling times for underwater gas metal arc welding of unalloyed steels...
-
Selection of Electrode Material for Inconel 617/P92 Steel SMAW Dissimilar Welds
PublikacjaThe present work aimed to investigate the microstructure and mechanical properties of the dissimilar shielded metal arc welded (SMAW) joint of Alloy 617 and P92 steel for advanced ultrasupercritical boilers. The SMAW joint was produced using three different types of electrodes, namely, ENiCrFe-3, ENiCrMo-3, and ENiCrCoMo-1. During microstructural observation of the welded joints, no possible cracking was detected in the weldments....
-
Storage of High-Strength Steel Flux-Cored Welding Wires in Urbanized Areas
PublikacjaThe condition of the consumables is a key factor determining the waste reduction in the welding processes and the quality of the welded joint. The paper presents the results of tests of four types of fux-cored wires dedicated for welding high-strength steels, stored for 1 month and 6 months in Poland in two urbanized areas: in a large seaside city (Gdańsk) and in Warsaw, located in the center of the country. The wires were subjected...
-
Testing of the longest span soil-steel bridge in Europe – new quality in measurements
PublikacjaThe article describes interdisciplinary and comprehensive diagnostic tests of final bridge inspection and acceptance proposed for a soil – steel bridge made of corrugated sheets, being the European span length record holder (25.74 m). As an effect of an original concept a detailed and precise information about the structure response was collected. The load test design was based on the nonlinear numerical simulations performed by...
-
Impact of laser beam welding on mechanical behaviour of 2.25Cr–1Mo (P22) steel
PublikacjaThe use of welding processes in the manufacturing and repair of structures intended for the energy industry plays a key role in the guarantee of a continuous supply of fossil fuels, which is the basic condition for ensuring energy security. A square butt joint of 10 mm thick plate of 2.25Cr–1Mo (P22) steel was fabricated by autogenous laser beam welding process and then post-weld heat treatment (PWHT) for two sets of process parameters...
-
Shaking table experimental study on models of steel buildings with different types of joints
PublikacjaThe aim of this paper is to study the response of models of steel buildings with destroyed and non-destroyed joints. The study was conducted experimentally using the shaking table tests. Two steel models were considered. Several types of joints were taken into account: totally destroyed joints, partially destroyed joints, welded joints and joints stiffened with additional metal. Six ground motions were taken into account. The acceleration...
-
Effects of Column Base Flexibility on Seismic Response of Steel Moment-Frame Buildings
PublikacjaSteel Moment Resisting Frames (SMRFs) are very popular lateral load resisting systems in many seismically active regions. However, their seismic response is strongly dependent on the rotational fixity of column base connections. Despite many studies (both experimental and numerical) in this particular area, available approaches for estimating column base flexibility have been validated only against laboratory test data. In the...
-
Friction-Induced Oscillations of a Non-Asbestos Organic Pin Sliding on a Steel Disc
PublikacjaFriction-induced oscillations result in deterioration of performance of disc brakes and are generally undesired. We conduct experimental study of friction-induced oscillations in a non-asbestos organic material / steel pair used in disc brakes of motor vehicles. The tests are done by use of a pin-on-disc machine which has the pin sample supported on a deformable beam. The adjustable friction parameters are the disc velocity, contact...
-
Weldability of Underwater Wet-Welded HSLA Steel: Effects of Electrode Hydrophobic Coatings
PublikacjaThe paper presents the effects of waterproof coatings use to cover electrodes on the weldability of high-strength, low-alloy (HSLA) steel in water. With the aim of improving the weldability of S460N HSLA steel in water, modifications of welding filler material were chosen. The surfaces of electrodes were covered by different hydrophobic substances. The aim of the controlled thermal severity (CTS) test was to check the influence...
-
Effect of Thermal Treatment and Erosion Aggressiveness on Resistance of S235JR Steel to Cavitation and Slurry
PublikacjaS235JR steel is used in many applications, but its resistance to the erosion processes has been poorly studied. To investigate this resistance, cavitation, and slurry erosion tests were conducted. These tests were carried out at different erosion intensities, i.e., different flow rates in the cavitation tunnel with a system of barricades and different rotational speeds in the slurry pot. The steel was tested as-received and after...
-
Interlayer defect evolution in an organic coating system on steel under hydromechanical loading
Publikacja -
Investigation of pitting corrosion of stainless steel by means of acoustic emission and potentiodynamic methods
Publikacja -
Column base fixity in steel moment frames: Observations from instrumented buildings
PublikacjaThe rotational fixity of column base connections in Steel Moment Resisting Frames (SMRFs) strongly influences their seismic response. However, approaches for estimating base fixity have been validated only against laboratory test data. These approaches are examined based on strong motion recordings from four instrumented SMRF buildings in California to informbest practices for seismic response simulation. These buildings represent...
-
Random field modelling of mechanical behaviour of corroded thin steel plate specimens
PublikacjaThe objective of this work is to explore the possibility of corrosion degradation modelling of thin steel plate specimens with the use of random field approach. The mechanical properties are obtained via the nonlinear Finite Element Analysis with the use of an explicit dynamic solver. The fully nonlinear material model is adopted to obtain the proper stress-strain response. Sensitivity analysis considering the main statistical...
-
Underwater in situ local heat treatment by additional stitches for improving the weldability of steel
PublikacjaIn this paper the influence of in situ local heat treatment performed by additional stitches on the weldability of high-strength low-alloy (HSLA) S355J2C+N steel was tested. The investigated steel is characterized by high susceptibility to cold cracking. It is necessary to find a method to improve the quality of welded joints. The local heat treatment was applied as an eect of bead-on plate welding made on the face of a Tekken...
-
FEM Calculations in Analysis of Steel Subsea Water Injection Flowlines Designing Process
PublikacjaPaper describes the result of theoretical research aimed at assessing the loads and operating conditions of a Coiled Tubing pipeline injecting water, suspended to the mining platform of Lotos Petrobaltic. For this purpose, appropriate calculation models have been developed using the Finite Element Method (FEM), taking into account the nature of the analyzed object and its loads. The analyzes were carried out for two pipes (previously...
-
Dynamic analysis of temporary steel grandstand equipped with different types of bracing system
PublikacjaIn the paper, behaviour of a temporary steel grandstand equipped with two different types of bracing system has been analysed through the numerical study. A typical solution concerning application of a diagonal tubular members has been compared with elements proposed by authors and called polymer dampers. A polymer element consists of two L-shape steel members bonded with polymer mass. The aim of the paper is to verify the effectiveness...
-
Analysis of temporary steel grandstand with different bracing systems exposed to crowd load
PublikacjaGrandstands are structures which are regularly subjected to dynamic loads generated by crowd motions. It is a dangerous situation when spectators induce rhythmic jumping, dancing, stamping, etc. If the synchronized movement of spectators excites a natural frequency of the structure, resonant response might occur. To avoid such situations, temporary steel grandstands are commonly strengthened using additional elements that create...
-
Influence of Parameters of Laser Beam Welding on Structure of 2205 Duplex Stainless Steel
PublikacjaLaser welding is used in modern industry, having many advantages comparing to traditional welding technologies. Nowadays, industry sectors such as shipbuilding, automotive and aviation can’t be imagined without laser processing technologies. Possibility of increase of welded joint properties, autogenous welding and high level of process automation makes the technology of laser welding perspective part of the industry. Physical...
-
Comparison of Different Measurement Techniques as Methodology for Surveying and Monitoring Stainless Steel Chimneys
PublikacjaThe measurement of a chimney axis is an engineering geodesy task. These measurements allow to assess the technical condition of chimneys and are usually carried out for reinforced concrete chimneys. When measuring high chimneys, the main problem may be the need to go a long distance to take a measurement. The surface of the chimney can also be problematic because it can absorb so much light from the range finder that total station...
-
FEM modelling of stress and strain distribution in weld joints of steel sandwich panels
PublikacjaThe development of laser welding technology has enabled the mass production of thin-walled structures, including steel sandwich panels. The technology of joining plating panels with stiffeners by welding allows us to create joints with a specific geometry and material properties. In comparison with other types of joints, laser welds are characterized by their specific behaviour under cyclic load and, as a consequence, a different...
-
Investigating the effects of structural pounding on the seismic performance of adjacent RC and steel MRFs
PublikacjaAn insufficient separation distance between adjacent buildings is the main reason for structural pounding during severe earthquakes. The lateral load resistance system, fundamental natural period, mass, and stiffness are important factors having the influence on collisions between two adjacent structures. In this study, 3-, 5- and 9-story adjacent reinforced concrete and steel Moment Resisting Frames (MRFs) were considered to investigate...
-
Load capacity of steel-aluminium brackets under static and cyclic laboratory tests
PublikacjaThe aim of the research is the laboratory investigation of steel-aluminium brackets employed to fasten lightweight curtain walls to building facilities. Static pressure, suction forces, and cyclic loads parallel to end plates (horizontal – to simulate wind influence) were applied in the study. The steel-aluminium brackets were tested on a reinforced concrete substrate made of C30/37 concrete class to simulate the real working conditions....
-
Study of the formation of calcareous deposits on cathodically protected steel in Baltic sea water
PublikacjaPurpose – The purpose of this paper is to investigate whether the sedimentation of calcareous deposits occurs on cathodically protected steel in Baltic sea water. Design/methodology/approach – Steel electrodes were cathodically polarized in natural Baltic sea water at potential þ0.150 V vs Zn electrode in potentiostatic mode. During exposure chronoamperometric measurements were carried out. After the exposure, the electrode’s surface...
-
Thermo-Mechanical Simulation of Underwater Friction Stir Welding of Low Carbon Steel
PublikacjaThis article investigates the flow of materials and weld formation during underwater friction stir welding (UFSW) of low carbon steel. A thermo-mechanical model is used to understand the relation between frictional heat phenomena during the welding and weld properties. To better understand the effects of the water environment, the simulation and experimental results were compared with the sample prepared by the traditional friction...