Filtry
wszystkich: 2420
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: POLYETHYLENE FILMS
-
Tribo-Environment Dependent Chemical Modification of Sliding Interfaces in Ultrananocrystalline Diamond Nanowall Film: A Correlation with Friction and Wear
PublikacjaTribological properties of ultrananocrystalline diamond nanowall (UNCD NW) films were investigated quantitatively in three different and controlled tribo-environmental conditions, proposing the passivation and graphitization mechanisms. However, these mechanisms are rather complicated and possibly can be understood in well-controlled tribological conditions. It was shown that the friction and wear of these films were high in highPage 1...
-
Morphology control via dual solvent crystallization for high-mobility functionalized pentacene-blend thin film transistors
PublikacjaWe present an approach to improving the performance of solution processed organic semiconductor transistors based on a dual solvent system. We here apply this to a blend containing the π-conjugated small molecule 6,13 bis(triisopropylsilylethynyl) pentacene (TIPS-pentacene) and polystyrene, which acts as an inert binder. Using a semiconductor-binder solution of two solvents, where the main solvent is a better solvent of the small...
-
Hydrogen effects in duplex stainless steel welded joints - electrochemical studies
PublikacjaIn this work results on the influence of hydrogen on passivity and corrosion resistance of 2205 duplex stainless steel (DSS) welded joints are described. The results were discussed by taking into account three different areas on the welded joint: weld metal (WM), heat-affected zone (HAZ) and parent metal. The corrosion resistance was qualified with the polarization curves registered in a synthetic sea water. The conclusion is that,...
-
Optical properties of tellurium dioxide thin films
Dane BadawczeTeO2 and TeO2 doped by Eu thin films manufactured by magnetron sputtering method were measured by optical spectroscopy. Metallic Te target and Te-Eu mosaic target with diameter of 50.8 mm were sputtered for about 45 min in argon-oxygen atmosphere what resulted in 300 nm film thickness deposition. The pressure in the chamber was below 0.2 Pa and substrate...
-
Luminescence properties of TeOx-Eu thin films
Dane BadawczeThe DataSet contains the emission and excitation spectra of TeOx-Eu thin films. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. Next, the 5% mol of europium ions were added, the nitrates were used as a source of rare-earth ions. The...
-
Luminescence properties of TeOx-Tb thin films
Dane BadawczeThe DataSet contains the emission and excitation spectra of TeOx-Tb thin films. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. Next, the 5% mol of terbium ions were added, the nitrates were used as a source of rare-earth ions. The...
-
Structural analysis of the tellurium dioxide thin films
Dane BadawczeTeO2 thin films were deposited by magnetron sputtering method. After deposition, amorphous samples were annealed at various temperatures. Influence of annealing temperature on a presence of crystalline phase was investigated.
-
Electrical measurements of the dewetting of metal thin films
Dane BadawczeIn situ observations of dewetting of thin films is very complicated. One of the method, that helps to observe it, could be electrical measurements. For experiments, thin gold, silver and gold-silver nanoalloy films were deposited by magnetron sputtering method. Films were deposited on a Corning glass substrates. Samples were measured by four point method...
-
Analysis of the electrical parameters of the LTO thin films
Dane BadawczeLithium titanate thin films were derived by sol-gel technique. Films with thickness ca. 800 nm were annealed for various time, in a range of 10h-80h at 550 deg. Electrical conductivity in a wide range of temperature was measured.
-
Structural investigations of the Al2O3 ultra thin films
Dane BadawczeUltra-thin layers of Al2O3 were deposited by atomic layer deposition (ALD) (Beneq TFS 200 ALD system). This method provides precise thickness control down to a single atomic layer. The precursors used were trimethylaluminum (Sigma-Aldrich) and purified water. The deposition of the atomic layer was carried out at 200 °C. Samples with a thickness of 2...
-
XRD analysis of the tellurium dioxide thin films
Dane BadawczeTellurium dioxide thin films were deposited by magnetron sputtering method. The XRD analysis of the films annealed at 200, 500, 650 and 700 celsius degree showed appearing of crystalline phase in a higher temeratures.
-
Luminescence properties of TeOx-Dy thin films
Dane BadawczeThe DataSet contains the emission and excitation spectra of TeOx-Dy thin films. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. Next, the 5% mol of dysprosium ions were added, the nitrates were used as a source of rare-earth ions....
-
Chemical investigation of the Al2O3 ultra-thin films
Dane BadawczeUltra-thin layers of oluminum oxide (Al2O3) were deposited by ALD method. Atomic layer deposition provides precise thickness control down to a single atomic layer. The precursors used were trimethylaluminum (Sigma-Aldrich) and purified water. The deposition of the atomic layer was carried out at 200 °C. Samples with a thickness of 2 and 8 nm of alumina...
-
Morphology of the sol-gel derived LTO:Cu films
Dane BadawczeMorphology of the lithium titanate doped by Cu thin films were investigated by SEM microscope. Films were deposited by spin-coater from sol-gel derived sol. SEM images showed a high porous structure, tipaciall for sol-gel based films. For measurements samples with a various content of Cu were selected.
-
Dewetting of silver films detected by XPS method
Dane BadawczeDewetting of silver thin films was detected by XPS method. Thin metallic films were deposited by magnetron sputtering method. Formation of nanostructures , as a result of thermal annealing, was confirmed by SEM microscope. For comparision three samples were measured. Bulg gold, as-deposited silver film with thickness of 3 nm and nanostructures.
-
XRD investigations of the lithium titanate thin films
Dane BadawczeNanocrystalline thin films with 800 nm thickness were prepared by sol–gel method. To examine the influence of the annealing temperature on as-prepared films crystallization, the coatings were heated at temperature from 500 °C up to 600 °C for 20h. Structure of manufactured thin films was investigated using X-ray diffraction (XRD). The most visible...
-
Valorization of bio-based polyols synthesized via biomass liquefaction
Dane BadawczeAs the properties of polyols have a huge impact on the properties of manufactured polyurethanes, this study aims to determine the influence of polyethylene glycols with different molecular masses on the course of the biomass liquefaction process and bio-polyol properties. The obtained polyols were characterized by rheological studies. To confirm the...
-
Reduction of parasitic pitch variations in archival musical recordings
PublikacjaA new method for reducing parasitic pitch variations in archival audio recordings is presented. The method is intended for analyzing movie soundtracks recorded in optical films. It utilizes image processing for calculating and reducing effects of tape shrinkage being one of the main reasons for parasitic pitch variations in audio accompanying moving images. As long as the film tape characteristics are known the new method can be...
-
Sandwich-type architecture film based on WS2 and ultrafast self-expanded and reduced graphene oxide in a Li-ion battery
Publikacja -
Sandwich-type architecture film based on WS2 and ultrafast self-expanded and reduced graphene oxide in a Li-ion battery
Publikacja -
Functional phase bistability in a nanocrystalline RbMn[Fe(CN)6] thin film fabricated by matrix-assisted laser evaporation
PublikacjaOne of the main barriers hindering applications of Prussian blue metal assemblies is their poor processability, which makes the fabrication of intact thin films very difficult. In this work, a nanocrystalline RbMn[Fe(CN)6]·xH2O film on silicon substrate was obtained for the first time via laser-stimulated deposition and investigated. Temperature-induced phase transition and bistability within broad hysteresis loop (120 K), along...
-
Analysis of the grain boundary conductivity for nanocrystalline doped ceria using the brick layer model.
PublikacjaW pracy przedstawiono wyniki badań elektrycznych i mikrostrukturalnych ceru domieszkowanego itrem. Gęste i nanokrystaliczne filmy przygotowane zostały z użyciem prekursorów polimerowych na szafirze. Konduktancja elektryczna była badana w funkcji temperatury syntezy, która jest skorelowana z wielkością ziaren. Otrzymano mniejszą konduktancję nanokrystalicznego filmu ceru w porównaniu z próbkami ceramicznymi.
-
Effect of package type on selected parameters of nutritional quality of chill-stored white sauerkraut
PublikacjaBrassica vegetables, including white cabbage, both fresh and sour (Brassica oleracea L. var. capitata L.), contain a lot of valuable metabolites which are effective in chemoprevention of cancer as documented by numerous studies. This work investigates the effect of different packaging types; low density polyethylene (PE-LD) and metalized polyethylene terephthalate (PET met/PE) with polyethylene bags on selected quality parameters in...
-
Nineteenth Century Theatre and Film (former title :Nineteenth Century Theatre)
Czasopisma -
Images. The International Journal of European Film, Performing Arts and Audiovisual Communication
Czasopisma -
Canadian Journal of Film Studies-Revue Canadienne d Etudes Cinematographiques
Czasopisma -
Pomiary grubości cienkich warstw metodą modulacji chromatycznej.
PublikacjaTematem artykułu jest pomiar grubości struktur cienkowarstwowych szerokostosowanych w optoelektronice, transparentnych warstw dielektrycznych. Grubość jest najistotniejszym parametrem warstwy i determinuje jej właściwościoptyczne. Metoda pomiaru grubości cienkich warstw powinna być bezkontaktowa, nieniszcząca, niekosztowna oraz odporna na zakłócenia
-
TEM and EDX study of the Al2O3 ultra thin films
Dane BadawczeThe ultra-thin layers of Al2O3 were deposited on a silicon substrates. The method of atomic layer deposition (Beneq TFS 200 ALD system) was chosen as the proper method of dielectric layer deposition. This method provides precise thickness control down to a single atomic layer. The precursors used were trimethylaluminum (Sigma-Aldrich) and purified water....
-
Au nanostructures coated with a ultrathin film of Al2O3 - measurements and FDTD simulations
Dane BadawczeGold plasmonic platforms have been coated with an ultra-thin films of aluminium oxide. Optical measurements, showing the influence of the thickness of Al2O3 on plasmon resonance position. The observed red-shift of the resonance location with the increase of the thickness of the Al2O3 film, can be explained by the change in the dielectric function of...
-
Julita Wasilczuk dr hab.
OsobyUrodzona 5 kwietnia 1965 roku w Gdańsku. W latach 1987–1991 odbyła studia na Wydziale Ekonomiki Transportu Uniwersytetu Gdańskiego (obecnie Wydział Ekonomii). Od 1993 roku zatrudniona na nowo utworzonym Wydziale Zarządzania i Ekonomii, Politechniki Gdańskiej, na stanowisku asystenta. W 1997 roku uzyskała stopień doktora nauk ekonomicznych na WZiE, a w 2006 doktora habilitowanego nauk ekonomicznych w dyscyplinie nauki o zarządzaniu,...
-
Application of the LPE-Grown LuAG: Ce Film/YAG Crystal Composite Thermoluminescence Detector for Distinguishing the Components of the Mixed Radiation Field
Publikacja -
Study on extraction and characterization of anchote (Coccinia abyssinica) starch and reinforced enset (Ensete ventricosum) fiber for the production of reinforced bioplastic film
PublikacjaPopulation expansion is causing an increase in dependence on plastic materials. The worst aspects of conventional plastics were their inability to biodegrade, their poor capacity to transmit water vapor, and their production of greenhouse gases. Usages of bioplastics are necessary for the advancement of a green economy and environment in order to eradicate these drawbacks of traditional plastics. In this study, reinforced bioplastic...
-
Novel two-step synthesis method of thin film heterojunction of BiOBr/Bi2WO6 with improved visible-light-driven photocatalytic activity
PublikacjaA novel two-step ionic liquid assisted procedure was applied for a controllable synthesis of BiOBr/Bi2WO6 heterojunction thin films. The preparation route involved an anodic oxidation of tungsten foil and hydrothermal transformation of as-anodized oxide in the presence of bismuth precursor and ionic liquid, N-butylpyridinium bromide [BPy][Br]. The BiOBr plates with irregular shapes adhered to the surface of flower-like Bi2WO6 and...
-
The effect of alkyl chain length on synergistic effects in micellization and surface tension reduction in nonionic gemini (S-10) and anionic surfactants mixtures
PublikacjaMixtures of nonionic gemini surfactant S-10 ( α, α'-[2,4,7,9-tetrametyl-5-decyne-4,7-diyl]bis[ω-hydroxy -polioxyetylene] with anionic SRS (sodium alkylsulfates) and SRSO3 (sodium alkylsulfonates) of different alkyl chain length (from 10 to 14 carbon atoms) were investigated. Surface tension measurements were used to find the cmc values and other adsorption parameters. The Clint, Rubingh’s and Rosen theories were applied for evaluation...
-
Te use of acoustic emission for assessment of the oil lubricity in a four-ball tester
Publikacjain view of the increased dynamic and temperature load in the compression-ignition engine tribological systems, particular attention is drawn to the problem of such lubrication of the friction nodes that after breaking the boundary layer it could be restored without any wear occurring. therefore, an idea has been devised of introducing to friction nodes, with the lubrication oils, of new substances (operational preparations) modifying...
-
A comparative performance assessment of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublikacjaThis work presents the investigation results of a journal bearing lubricated with magnetorheological fluid that is activated by a local constant magnetic field to vary both the local flow resistance and pressure. The bearing performance is assessed via Finite Element Modelling (FEM) and results are corroborated by experiments. The FEM model uses the Bingham model to describe the fluid film. A dedicated test rig is used to assess...
-
Ewa Bieńkowska Culture Films, Texts & Quizes
Kursy Online -
XRD patterns of V2O5 thin films deposited on silicon substrate
Dane BadawczeThe DataSet contains the XRD patterns of V2O5 thin films deposited on a silicon substrate. The as-prepared thin films were annealing under an oxidizing atmosphere in the temperature range of 300-600C. The results show that the structure of the films dependent on the annealing temperature.
-
XRD patterns of V2O5 thin films deposited on quartz glass
Dane BadawczeThe DataSet contains the XRD patterns of V2O5 thin films deposited on a quartz glass substrate. The as-prepared thin films were annealing under an oxidizing atmosphere in the temperature range 200-600C. The results show that the structure of the films dependent on the annealing temperature.
-
Chemical investigations of the MoO3 doped by K films deposited FTO
Dane BadawczeMoO3 thin films were synthesized via thermal annealing of thin, metallic Mo films deposited onto the FTO substrate using a magnetron sputtering system. The influence of photointercalation of alkali metal cation (K+) into the MoO3 structure on the photoelectrochemical properties of the molybdenum trioxide films was investigated. The chemical characterisation...
-
Substrate characterization in a electrochemically derived Manganium-Cobaltium thin films
Dane BadawczeManganium-Cobaltium thin films were electrochemically deposited on a Ni foams subsrates in a one-step process at −1.1 V vs. Ag/AgCl in an aqueous solution of differently concentrated Mn(NO3)2·4H2O and Co(NO3)2·6H2O with the deposition time limited by charges of 60, 120, and 200 mC at 25 °C. The concentration ratios of Mn(NO3)2·4H2O to Co(NO3)2·6H2O...
-
Optical measurements of LTO:Cu sol-gel derived thin films
Dane BadawczeLithium titanate doped by copper thin films were manufactured by chemical, sol-gel method. Flms were deposited on a Corning glass substrated by spin coater. To calculated optical band gap and other optcal parameters, UV-VIS spectroscopy measurements were performed. For measurements selected samples with various content of Cu.
-
Impedance spectroscopy of the lithium titanate doped by copper thin films
Dane BadawczeLithium titanate doped by copper thin films were derived by sol-gel method. Prepared gel was deposited by spin-coating technique. Samples with various content of Cu were measured by impedance spectroscopy method in a wide range of temperature, from -120 up to 150 deg.
-
Substrate Dependence in the Formation of Au Nanoislands for Plasmonic Platform Application
PublikacjaIn this work, the influence of the various substrates on Au nanoisland formation has been studied. Nanostructures were obtained via annealing of thin Au films. In order to determine nanoisland formation mechanisms, correlation between an initial film thickness and temperature of formation, shapes, and dimensions of nanostructures was examined. For the surface morphology studies, nanograin structure, and chemical composition analysis,...
-
Input files for the Floodsar software
Dane BadawczeInput files for the Floodsar softwareAuthor: Tomasz Berezowski, Gdansk University of Technology, tomberez@eti.pg.edu.pl
-
Synthesis of eosin modified TiO2 film with co-exposed {001} and {101} facets for photocatalytic degradation of para-aminobenzoic acid and solar H2 production
PublikacjaOwing to the increasing photosensitivity and DNA damage properties of para-aminobenzoic acid (PABA), concerns have been raised over the exposure of humans to PABA. Solar light-driven photocatalysis (SPC) provides a promising solution for the effective removal of organic pollutants especially when directed towards sulfate radical (SO4−) production. Herein, we have developed a sulfite-enhanced SPC using Eosin-Y sensitized TiO2/Ti...
-
Merton-type default risk and financial performance: the dynamic panel moderation of firm size
PublikacjaPurpose – The main purpose of this study is to evaluate the probability of default and examine the relationship between default risk and financial performance, with dynamic panel moderation of firm size. Design/methodology/approach – This study utilizes a total of 1,500 firm-year observations from 2013 to 2018 using dynamic panel data approach of generalized method of moments to test the relationship between default risk and financial...
-
The AFM micrographs of vanadium oxides thin films obtained at 800°C
Dane BadawczeThe DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on a silicon substrate and vanadium thin films were obtained by annealing as-prepared films at...
-
The AFM micrographs of vanadium oxides thin films obtained at 1200°C
Dane BadawczeThe DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on quartz glass and silicon substrate and vanadium thin films were obtained by annealing as-prepared...
-
SEM micrographs of morphology evolution of V2O5 thin films on quartz glass
Dane BadawczeThe DataSet contains the scanning electron microscopy (SEM) micrographs of V2O5 thin films deposited on a quartz glass substrate. The as-prepared thin films were annealing under an oxidizing atmosphere in the temperature range 200-600C. The results show that the morphology of the films dependent on the annealing temperature.