Filtry
wszystkich: 5298
-
Katalog
- Publikacje 4521 wyników po odfiltrowaniu
- Czasopisma 373 wyników po odfiltrowaniu
- Konferencje 29 wyników po odfiltrowaniu
- Osoby 100 wyników po odfiltrowaniu
- Projekty 10 wyników po odfiltrowaniu
- Kursy Online 81 wyników po odfiltrowaniu
- Wydarzenia 10 wyników po odfiltrowaniu
- Dane Badawcze 174 wyników po odfiltrowaniu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: EXPERIENTIAL LEARNING
-
Numerical modelling and experimental verification of compressible squeeze film pressure
PublikacjaThe validity of using the Reynolds equation for compressible squeeze film pressure was tested with computational fluid dynamics (CFD). A squeeze film air bearing was instrumented with pressure sensors and non-contacting displacement probes to provide transient measurements of film thickness and pressure. The film thickness measurements also provided input parameters to the numerical prediction. However, numerical results showed...
-
Experimental and numerical identification of separation zones in the cent-rifugal compressor
PublikacjaW pracy przedstawiono analizę przepływu w obszarze koła wirnikowego oraz dyfuzora bezłopatkowego sprężarki powietrza. Wyniki obliczeń w ramach modelu 3D (FLUENT 5.5) porównano z wynikami badań laboratoryjnych na stanowisku sprężarkowym Katedry Sprężarek w Sankt Petersburgu. Celem porównania jest ocena możliwości identyfikacji stref przepływu z oderwaniem, w ramach modeli dostępnych w wykorzystanym programie obliczeniowym. W wyniku...
-
Experimental and numerical identification of corrosion degradation of ageing structural components
PublikacjaThe study presents experimental and numerical identification of corrosion degradation of thin-walled structural components employing guided wave propagation. The steel structural components are subjected to through-thickness varying corrosion degradation levels. The developed approach using the non-destructive guided wave-propagation quantifies the equivalent average corrosion degradation level by exploring a limited number of...
-
Experimental study of the multi-disc negative brake for a hydraulic motor
PublikacjaThis paper describes the methodology for experimental testing of a multi-disc brake. The construction of this brake was also present. The brake is dedicated to hydraulic motors with a small working volume. Experimental tests were carried out on a brake with plates immersed in oil and, for comparison, tests were carried out on a dry brake. As a result of the tests, the permissible torque (load) that is able to transfer the brake...
-
Direct reduction of pellets through hydrogen: Experimental and model behaviour
PublikacjaThis paper presents the hydrogen reduction behaviour of industrial pellets designed for the efficient hydrogen based direct reduction. The pellets were provided with very low non ferrous oxides percentage (0.52 of basicity index) and with the absence on TiO2 oxides. The pellets measured diameters in the range 1.14–1.72 cm and were characterized in terms of porosity, pores size, tortuosity and compression strength. The pellets were...
-
Experimental Verification of the CFD Model of the Squeeze Film Lifting Effect
PublikacjaAbstract: The presented study shows the results of the research into the squeeze film levitation phenomena. The system introduced in the investigation is composed of a vibrating surface, air squeeze film, and the surface of the body freely suspended over the film. The use of the CFD (Computational Fluid Dynamics) model used in the system allows us to determine the steady state, periodic behavior of the air film (described by Navier–Stokes,...
-
Experimental study on earthquake-induced pounding between steel structures
PublikacjaPounding between adjacent structures has been repeatedly observed during major earthquakes. The phenomenon may cause some local damage at the points of interactions, it may also lead to substantial destruction, permanent deformations or total collapse of colliding structures. The effects of earthquake-induced structural pounding have been studied for more than three decades now. However, most of the studies concerned masonry as...
-
Methodology of experimental research on efficiency of hydro-mechanical automatic gearbox
PublikacjaThe article shortly describes the design and principle of operation of the hydromechanical gearbox and presents the methodology and design of test stands used for testing hydromechanical proto-type gearbox developed at Technical University of Gdansk. The article presents an approach according to which, in order to obtain reliable measurement data, it is necessary to separate the tests of the hydraulic and mechanical parts of the...
-
Experimental study and numerical simulation of the dynamic penetration into dry clay
PublikacjaTests of dry clay were carried out in a uniaxial stress state using the experimental setup which implements the split Hopkinson pressure bar method. Based on the results of these experiments, the compressive strength of clay was determined as an important element of S.S. Grigoryan’s model of the soil medium. In addition, the parameters of this model are determined from the results of experiments using the modified Kolsky method...
-
Influence of operation of national experimental nuclear reactor on the natural environment
PublikacjaThis paper presents the impact of experimental nuclear reactor operations on the national environment, based on assessment reports of the radiological protection of active nuclear technology sources. Using the analysis of measurements carried out in the last 15 years, the trends are presented in selected elements of the environment on the Świerk Nuclear Centre site and its surroundings. In addition, the impact of research results...
-
Recent progress in experimental studies of electrohydrodynamic flow in electrostatic precipitators
PublikacjaMany experimental, theoretical and numerical works were devoted to the electrohydrodynamic (EHD) flow generated in electrostatic precipitators (EPSs). The generally accepted conclusion from these studies is that the EHD flow plays an important role in the particle collection in ESPs. However, despite of the recent fast progress in numerical simulation and experimental techniques used in the ESPs studies many problems related to...
-
Experimental Study of the Resistance to Influence of Aggressive Liquids on Lightweight Concrete
PublikacjaIn light of the scientific research, the corrosion of concrete structures is one of the main problems that may reduce their durability due to the negative impact of the natural environment. The paper analyzes the influence of the type of component on the selected properties of lightweight concrete subjected to the influence of aggressive liquids. Four concrete mixes were prepared with a granular aggregate made of foamed glass (GEGA)...
-
A numerical and experimental analysis of multi-hole orifice in turbulent flow
PublikacjaIn this research study, the comprehensive metrological analysis is investigated for a 4-hole orifice with module m = 0.25 installed in the pipeline with an internal diameter of 50 mm. A detailed numerical simulation was performed for the turbulence models: k-ε-realizable and k-ω-BSL. The novelties of the research include model validation by comparing the results of numerical studies with the experiment conducted in the area of...
-
Experimental investigations and simulations of the microturbine unit with permanent magnet generator
PublikacjaIn dispersed power generation, low power devices are used for local combined generating of heat end electric power. There are developing concepts of micropower plants with electric generators driven by steam or gas microturbines. The paper presents the results of an experimental investigations of the microturbine set consists of the turbine with partial admission, permanent magnet generator and three phase AC-to-DC rectifier. The...
-
Experimental study and numerical optimization of tensegrity domes – A case study
PublikacjaThe paper deals with the design, experimental analysis and numerical optimization of tensegrity dome models. Two structures are analyzed – a Geiger system dome (preliminary dome), with PVC-U bars and PA6/PP/PET tendons and a Fuller system dome (target dome), with wooden bars and steel cables as tendons. All used materials are experimentally tested in terms of Young's modulus and yield stress values, the compressed bars are also...
-
PROBLEMS OF EXPERIMENTAL DETERMINATION OF COEFFICIENTS OF THE WEAR OF SHIP PIPING SYSTEMS
PublikacjaThe article presents series of considerations relating to experimental evaluation of the reliability of ship piping systems. The aim of this study is to attempt to answer the following questions: What should be the tested element? How to choose the diameter of the tested item? What should be the result of measurements and calculations? How to measure? How to choose the duration of the test? How to choose the sample size and elaborate...
-
Experimental study on the effectiveness of polymer dampers in reduction of structural vibrations
PublikacjaVibrations of civil engineering structures, generated by dynamic loads, may be very dangerous to the structures themselves as well as may have significant influence on human perception and comfort. A number of different methods have been proposed in order to minimize such situations. This concern newly designed structures as well as those which dynamic properties have to be modified due to problems with excessive vibrations. One...
-
Experimental and numerical analysis of an aluminum cantilevered beam with polymer adhesive
PublikacjaIn this paper, experimental and numerical investigation on a composite cantilevered aluminum beam has been conducted. The subject of the study consists of two plain aluminum elements bonded with polymer adhesive of different thickness. It has been proven in the previous study that this kind of material has high damping properties. During an experimental investigation, value of damping ratios have been obtained. The aim of a numerical...
-
Harmonics produced by traction substations – computer modelling and experimental verification
PublikacjaVoltage and current harmonics have a detrimental effect on the components of a power system. Current harmonics may result in the overload and damage to power transformers. Voltage harmonics may result in, for example, damage to capacitor banks used to compensate reactive power. Devices which contribute to both current and voltage distortion include traction rectifiers. This paper presents results of the computer investigation of...
-
Dynamic tests of composite footbridge segment – experimental and numerical studies
PublikacjaExperimental dynamic tests and numerical simulations of a 3 meters long segment of a footbridge made of polymer composites are presented in the paper. The span-length is reduced, however dimensions of cross-section are the same as the target footbridge. The segment structure is made of sandwich panels, which consist of fibre reinforced polymer (GFRP) laminates (skins) and a PET foam (core). The first part of the paper contains...
-
Selected Problems of Experimental Testing Marine Stern Tube Bearings
PublikacjaThis paper presents typical methods for conducting experimental tests on main shaft slide bearings. There are described their possible testing capabilities, advantages, drawbacks and limitations. Various testing methods were analyzed to find a solution able of providing a wide range of possible investigations at possibly acceptable limitations.
-
FE analysis of support-specimen interaction of compressive experimental test
PublikacjaThe objective of this work is to investigate the support-specimen interaction during the compressive experimental testing of stiffened plates. The interaction is analyzed employing the nonlinear Finite Element Method using the commercial software ANSYS. The connection between the stiffened plate and testing supports is modelled with the use of contact elements, where several possible interaction scenarios are investigated, and...
-
EXPERIMENTAL EVALUATION OF DLC/STEEL SLIDING CONTACTS’ OPERATIONAL ENVELOPE
PublikacjaIn an industrial project concerning sliding bearings, a sliding pair was selected of high alloy steel vs. industrial grade DLC coated high alloy steel as a basis for an innovative design of high performance sliding bearings lubricated with a synthetic oil for use in geared transmission units. The development process required credible data on the ultimate resistance of the sliding pair to very high contact stress. An experimental...
-
Experimental study of the effect of vertical acceleration component on the slope stability
PublikacjaThe paper deals with the stability of earth dams subjected to seismic and paraseismic excitations occurring in the close distance to the dam. The Newmark’s stability approach, classified as a simplified dynamic method, has been extended for two directional dynamic loading case and the evolution of the friction coefficient. The paper is focused on the experimental verification of the proposed method for harmonic and cyclic excitations...
-
Experimental investigation into surface texture effect on journal bearings performance
PublikacjaThe aim of this study was to analyse the performance of journal bearings with specially created dimples on the sliding surface and operating under various conditions. The texture was created on the bearing surface that co-acted with the smooth journal; moreover, the variation of the textured surface of the journal mating with the smooth bearing was tested, and the results were compared to those obtained with the standard smooth...
-
FEM ANALYSIS AND EXPERIMENTAL TESTS OF RIGID RISER HANGING SYSTEM
PublikacjaThe article presents the analysis, project, and experimental examination of an original rigid riser for Coil Tubing Pipes. The principle of riser operation is based on the use of friction forces. The research included the FEM analysis of the designed riser, calculations of the required bolt tensions, and checking the effect of the clamping force on stress distribution in the pipeline. The results of computer simulation were verified...
-
Experimental Investigations on the Influence of Coil Arrangement on Melting/Solidification Processes
PublikacjaThe latent heat thermal energy storage units are very popular because of their high energy density and almost close to constant temperature during the charging/discharging. In the present study has been proposed new shell-and-coil geometry with a shifted coil position to enhance the performance of phase change thermal magazine. The experimental investigations have been performed both for the melting and solidification process of...
-
Experimental research of the effect of face milling strategy on the flatness deviations
PublikacjaIn this paper the dependencies between face milling strategy of EN AW6082-T6 aluminum alloy samples, with difference thicknesses (6, 8, and 12 mm) and two cold rolling directions, and flatness deviations were presented. Three strategies of milling included different proportions of material removed from both sides of the plates. This approach allowed to control the proportions of residual surface stresses on both sides of the specimens,...
-
Generalization of Phylogenetic Matching Metrics with Experimental Tests of Practical Advantages
PublikacjaThe ability to quantify a dissimilarity of different phylogenetic trees is required in various types of phylogenetic studies, for example, such metrics are used to assess the quality of phylogeny construction methods and to define optimization criteria in supertree building algorithms. In this article, starting from the already described concept of matching metrics, we define three new metrics for rooted phylogenetic trees. One...
-
Time-frequency characteristics of chemical oscillations. Experimental and model studies.
PublikacjaW publikacji zaprezentowano wykorzystanie czasowo-częstotliwościowych metod analizy sygnałów niestacjonarnych do badania reakcji Biełousowa-Żabotyńskiego. Zastosowanie krótkoczasowej transformaty Fouriera (STFT) pozwoliło na uzyskanie spektrogramów przedstawiających zmiany energii i częstotliwości oscylacji w trakcie trwania reakcji chemicznej. Przedyskutowano podobieństwa i różnice pomiędzy spektrogramami wygenerowanych dla eksperymentalnych...
-
Theoretical and experimental treatment of a microstrip coupled ferrite line circulator.
PublikacjaArtykuł opisuje wyniki badań teoretycznych i eksperymentalnych cyrkulatora realizowanego w technice sprzężonych ferrytowych linii mikropaskowych. W stosunku do wcześniejszych metod zastosowano do realizacji układu strukturę linii mikropaskowych w których ferryt położony jest na górze mikropaska. Struktura umożliwiła zmniejszenie strat układu w stosunku do wcześniej przyjętych technologii.
-
Nucleate pool boiling modelling and experimental investigation : chapter 7
PublikacjaOmówiono wpływ powłoki porowatej nanoszonej na całą powierzchnię rurki lub jej fragment na osiągany współczynnik przejmowania ciepła, krytyczne gęstości strumienia ciepła, a także obwodowy rozkład temperatury przy wrzeniu pęcherzykowym na zewnętrznej powierzchni poziomej rurki.Przedstawiono wyniki badań częstotliwości odrywania się pęcherzyków oraz pól prędkości wokół wzrastającyh i unoszących się pęcherzyków przy wrzeniu z pojedynczych...
-
The experimental method of reducing magnetic field intensity in industrial buidings
PublikacjaPrzedstawiono metodę obniżenia poziomu intensywności zakłóceń w budynkach pracującego zakładu przemysłowego. Potrzeba wykonania badań pola elektromagnetycznego wynikała m.in. z zaobserwowanej wśród pracowników jednego z działów zakładu większej podatności na zachorowania. Na drodze pomiarów zlokalizowano źródła silnego pola magnetycznego w zakresie małych częstotliwości. Na podstawie analizy wyników pomiarowych sformułowano wnioski...
-
Experimental comparison of UML-HAZOP inspection and non-structured review
PublikacjaArtykuł przedstawia eksperyment przeprowadzony na Politechnice Gdańskiej mający na celu porównanie dwóch technik przeglądowych. Poszczególne rozdziały zawierają: ogólne omówienie tematyki przeglądów i inspekcji, przedstawienie metody UML-HAZOP, opis przebiegu eksperymentu oraz uzyskanych rezultatów.
-
Experimental and numerical analysis of streamwise vortex generator for subsonic flow
PublikacjaW pracy przedstawiono porównanie wyników obliczeń numerycznych dwoma kodami (FLUENT i SPARC) na tle badań eksperymentalnych generatora wirów wzdłużnych. Przedstawiono wyniki dla liczb Macha przepływu głównego 0.3 i 0.8. Porównano ciśnienie całkowite w dwóch przekrojach za otworem przez który realizowany jest wydmuch. Przedstawiono strukturę wiru wzdłużnego uzyskaną dla obu programów. Średnica otworu jetu jest równa 1mm, co odpowiada...
-
Experimental and theoretical investigations of silo music during granular flow
PublikacjaPraca dotyczy analizy efektów dynamicznych w silosach podczas przeływu materiałów sypkich.
-
Experimental and theoretical studies of resonance effects during silo flow.
PublikacjaPrzedstawiono badania nad rezonansowymi efektami dynamicznymi podczas przepływów silosowych. Wpływ rezonansu na wielkość naporu był analizowany przy pomocy badań doświadczalnych i obliczeń MES na bazie prawa mikropolarnego sprężysto-plastycznego. Doświadczenia wykonano w silosie o przekroju okrągłym i prostokątnym. Zaproponowano efektywną metodę redukcji efektów dynamicznych.
-
The experimental results of diesel fuel spray with marine engine injector
Dane BadawczeThe data set presents the measurement of the diesel fuel spray from with marine engine injector. The main target presents results is a study of the time course of macro parameters (spray tip penetration, spray cone angle) of fuel spray in the cylinder of marine diesel engine. The impact of ambient conditions and the geometrical parameters of the injector...
-
Some problems of slide bearing material fatigue evaluation.
PublikacjaA slide bearing alloy resistance against fatigue failures have been investigated for three different lubricants, different heat loadings and different stress ratio κ values. The research methods and data handling procedures for determination of particular parameter effects on fatigue strength have been described and analysed for experiments that were set and performed in laboratory tester SKMR-2. Main and interaction effects of...
-
Estimation of pile bearing capacity by dynamic and static tests
PublikacjaBadania dynamiczne, szczególnie dla pali wbijanych, w budownictwie hydrotechnicznym stają się coraz bardziej popularne. Badania, poparte formalnie zapisami zawartymi w Eurokodzie 7, wykorzystywane w badaniach ''na wodzie'' i ''na lądzie'' są szybkie i ekonomiczne. Przedstawiono serię badań dla gruntów uwarstwionych dla pali prefabrykowanych żelbetowych, wbijanych stalowych pali rurowych oraz pali Vibro-Fundex. Badania dynamiczne...
-
Multimedia services applied to noise and hearing monitoring and measuring
PublikacjaThe goal of this chapter is to show a research study related to processing of data acquired by the multimedia services engineered at the multimedia systems department (MSD) of the Gdansk University of Technology. This concerns a survey on noise threat employing the multimedia noise monitoring system (MNMS) and hearing tests performed by the "I can hear. . . " system. The obtained results of the noise measurements revealed that...
-
Modeling lubricant flow between thrust-bearing pads
PublikacjaInlet temperature is one of the main inputs in all models for the analysis of fluid film bearing performance. At the same time, inlettemperature distribution and also oil velocity distribution at the inlet are the result of flow phenomena in the gap between the bearingpads. These phenomena are complex and in many cases further affected by any special arrangements of forced oil supply to the gapbetween pads. The reason for such...
-
Investigation of Noise Threats and Their Impact on Hearing in Selected Schools
PublikacjaNoise measurements conducted in selected schools in Gdansk area are presented in this paper. The main aim of this research was to determine noise threats at schools. Some objective measurements of the acoustic climate were performed employing a noise monitoring station engineered at the Multimedia System Department, Gdansk University of Technology. Simultaneously, subjective noise annoyance examinations were carried out among pupils...
-
Audiovisual speech recognition for training hearing impaired patients
PublikacjaPraca przedstawia system rozpoznawania izolowanych głosek mowy wykorzystujący dane wizualne i akustyczne. Modele Active Shape Models zostały wykorzystane do wyznaczania parametrów wizualnych na podstawie analizy kształtu i ruchu ust w nagraniach wideo. Parametry akustyczne bazują na współczynnikach melcepstralnych. Sieć neuronowa została użyta do rozpoznawania wymawianych głosek na podstawie wektora cech zawierającego oba typy...
-
Computer simulations of hearing aid acoustical system performance
Publikacja -
Psychogenic Polydipsia leading to Hyponatremia induced Seizure in Schizophrenia.
Publikacja -
Influence of Collar Deformations on Hydrodynamic Thrust Bearing Performance
Publikacja -
Fitting the mobile device characteristics to the user's hearing preferences
PublikacjaA method for fitting the mobile computer audio characteristics to the user's hearing preferences is proposed. The process consists of two stages: calibration and dynamics processing. During the calibration phase the user performs a loudness scaling test giving their response regarding the perceived loudness. The dynamics processing made on above basis sets the loudness to the most comfortable level. The processing accounts both...
-
A study on signal processing methods applied to hearing aids
PublikacjaThis paper presents a short survey on current technology available in hearing aids with a focus on digital signal processing techniques used. First, factors influencing the hearing aid effectiveness are introduced. Then, examples of the present DSP methods and strategies are provided. Also, a description of current limitations of hearing aids and future trends of development are shown. Finally, the notion of computational auditory...
-
Large hydrodynamic thrust bearing: Comparison of the calculations and measurements
PublikacjaHydrodynamic thrust bearings, used to carry axial loads in heavily loaded shafts of water power plants hydro turbines, can reach outer diameters even exceeding 5 m. In such large objects scale effect could be observed. According to this, allowable bearing specific load assuring safe operation of the bearings has to be decreased, which increases thrust bearing dimensions. This effect is caused by excessive thermal deflections of...