Wyszukiwarka
Katedra Konstrukcji Maszyn i Pojazdów
Publikacje
Filtry
wszystkich: 484
Katalog Publikacji
Rok 2018
-
Badania pojazdów zabytkowych - wymagane dokumenty
PublikacjaBadanie, jakiemu poddawany jest pojazd w stacji kontroli pojazdów, kwalifikujące go do pojazdów zabytkowych nazywane jest "Badaniem co do zgodności z warunkami technicznymi pojazdów zabytkowych". Rozporządzenie określa zakres i sposób prowadzenia badań zgodności z warunkami technicznymi pojazdów zabytkowych.
-
BALISTYKA DLA SNAJPERÓW: PRAKTYCZNY PORADNIK
PublikacjaJest książka z zakresu balistyki, opracowana dla snajperów, strzelców wyborowych, sportowych strzelców długodystansowych oraz myśliwych. W przystępny sposób przedstawiono w niej zagadnienia związane z balistyką wewnętrzną, zewnętrzną i końcową. Bardzo wnikliwie omówiono również celowniki optyczne, sposoby ich testowania i regulacji. Opisano zasady określania poprawek uwzględniających odległość od celu, położenie i ruch celu oraz...
-
COMPARISON OF NOISE EMISSION OF HCT AND CLASSIC VEHICLE COMBINATIONS FOR TIMBER TRANSPORTATION IN SWEDEN
PublikacjaBy means of a special simulation tool, the noise emission of a high-capacity heavy vehicle (11 axles) was compared to that of a classic heavy vehicle (a truck-dolly-semitrailer with 8 axles). The two cases are designated “Extended vehicle” versus “Classic vehicle” in this study, having total lengths of 34 and 25 m, respectively. The Classic vehicle represents the most common articulated heavy vehicle configuration for transport...
-
Computing methods for fast and precise body surface area estimation of selected body parts
PublikacjaCurrently used body surface area (BSA) formulas give satisfactory results only for individuals with typical physique, while for elderly, obese or anorectic people accurate results cannot be expected. Particularly noteworthy are the results for individuals with severe obesity (body-mass index greater than 35 kg/m2), for which BSA estimation errors reached 80%. The main goal of our study is the development of precise BSA models for...
-
Decreasing CO2 Emissions By Reducing Tire Rolling Resistance
PublikacjaThe first motor vehicle was built by Nicolas Cugnot almost 250 years ago and since then there has been a continuous process of motor vehicles’ improvements, as well as development of new road pavements. The fuel crisis of the 70s of the 20th century made it clear to vehicle builders that measures should be taken to reduce vehicle fuel consumption and it contributed to an increased interest in electric vehicles. Although significant...
-
Determinants of the surface quality, density and dimensional correctness in selective laser melting of the Ti-13Zr-13Nb alloy
PublikacjaSelective laser melting is widely used for custom-designed elements. Successful manufacturing depends on laser treatment parameters and material features. This research aimed to determine the effects of laser power, scan time and hatch distance on surface quality, relative density and dimensional precision for cuboids made of the Ti-13Zr-13Nb alloy. The influence of energy density, energy flux and pre-heating was seen to be decisive...
-
Ecological bearing systems for water turbines – research and development at Gdansk University of Technology
PublikacjaIncreasing requirements for environmental protection make it necessary to introduce new materials and designs. Hydroelectric power plants operating in direct contact with water reservoirs and rivers are potentially endangering water cleanliness, hence they should also be modernized in the way minimizing the environmental hazards. A lot of progress in this field has been achieved in last decades, but still there is much work to...
-
Energetic model of hydraulic system of refuse collection vehicle based on simulation and experimental data
PublikacjaThis paper presents an energetic model of hydraulic system of a refuse collection vehicle. First, benefits resulting from implementation of an energetic model in the industry and operation of a Refuse Collection Vehicle are briefly explained. Then, components of the energy consumption in hydraulic circuits of compactor and lifting device are described and combined into a comprehensive model that can be evaluated using basic measurement...
-
Engineering Analysis with ANSYS Software Second Edition
PublikacjaThe best way to learn complex systems is by means of hands-on experience. With an innovative and clear tutorial based approach, this powerful book provides a comprehensive introduction to the fundamental areas of engineering analysis needed on research or commercial engineering projects. With its detailed step-by-step explanations and sample problems, this book will develop the reader's understanding of FEA and their ability to...
-
Evaluation of bearing and journal damage in MAN 9L40-54 engines installed on M/V STENA SCANDINAVICA ferry
PublikacjaThe following report was requested by Remontowa Shiprepair Yard (RSY) S.A. in Gdansk ´ (contract no. 4/2018/EX/U, dated 13.02.2018) and prepared based on the materials received from RSY, two on-board inspections and the participation of the contractors in three conferences with RSY representativesi. The goal of the analysis performed by the experts of Gdansk University of Technology was ´ to determine the character of the bearing...
-
Evaluation of the efficiency of the duty cycle of refuse collection vehicle based on real-world data
PublikacjaIn this paper a method of the efficiency evaluation of the duty cycle of Refuse Collection Vehicle is presented. Using real world data, two representative duty cycles were analysed. Total cycle efficiency was calculated, as well as the efficiency of particular cycle phases. Then, energy needed to collect and compact the waste and energy from fuel were compared. Measured and calculated values were shown on the diagrams illustrating...
-
Experimental determination of general characteristic of internal combustion engine using mobile test bench connected via Power Take-Off unit
PublikacjaThe general characteristics of the engine include information about the regions of the engine's operating area that are most efficient, where specific fuel consumption reaches the smallest values. Economic operation based on those characteristics can contribute to a significant reduction of fuel consumption and consequently less pollutant emissions and lower costs. The paper presents an experimental method of determination of general...
-
EXPERIMENTAL EVALUATION OF DLC/STEEL SLIDING CONTACTS’ OPERATIONAL ENVELOPE
PublikacjaIn an industrial project concerning sliding bearings, a sliding pair was selected of high alloy steel vs. industrial grade DLC coated high alloy steel as a basis for an innovative design of high performance sliding bearings lubricated with a synthetic oil for use in geared transmission units. The development process required credible data on the ultimate resistance of the sliding pair to very high contact stress. An experimental...
-
Failure of cold-formed beam: How does residual stress affect stability?
PublikacjaIn machine industry, stresses are often calculated using simple linear FEM analysis. Occasional failures of elements designed in such a way require recomputation by means of more sophisticated methods, eg. including plasticity and non-linear effects. It usually leads to investigation of failure causes and improvement of an element in order to prevent its unwanted behavior in the future. The study presents the case where both linear...
-
FEM ANALYSIS AND EXPERIMENTAL TESTS OF RIGID RISER HANGING SYSTEM
PublikacjaThe article presents the analysis, project, and experimental examination of an original rigid riser for Coil Tubing Pipes. The principle of riser operation is based on the use of friction forces. The research included the FEM analysis of the designed riser, calculations of the required bolt tensions, and checking the effect of the clamping force on stress distribution in the pipeline. The results of computer simulation were verified...
-
FEM Calculations in Analysis of Steel Subsea Water Injection Flowlines Designing Process
PublikacjaPaper describes the result of theoretical research aimed at assessing the loads and operating conditions of a Coiled Tubing pipeline injecting water, suspended to the mining platform of Lotos Petrobaltic. For this purpose, appropriate calculation models have been developed using the Finite Element Method (FEM), taking into account the nature of the analyzed object and its loads. The analyzes were carried out for two pipes (previously...
-
HYDROSTATIC THRUST BEARING WITH REDUCED POWER LOSSES
PublikacjaIn many cases in rotating machinery, axial load is carried by tilting pad thrust bearings which have been developed since the beginning of 20th century. For high reliability and simplicity, most commonly the bearings are bath lubricated. In the times of sustainable development, however, minimization of friction losses becomes an important criterion for machinery assessment, and a strategic goal of their development. Performed calculations,...
-
Improvement of Thrust Bearing Calculation Considering the Convectional Heating within the Space between the Pads
PublikacjaA modern thrust bearing tool is used to estimate the behavior of tilting pad thrust bearings not only in the oil film between pad and rotating collar, but also in the space between the pads. The oil flow in the space significantly influences the oil film inlet temperature and the heating of pad and collar. For that reason, it is necessary to define an oil mixing model for the space between the pads. In the bearing tool, the solutions...
-
INFLUENCE OF TEMPERATURE ON THE TYRE ROLLING RESISTANCE
PublikacjaTemperature is a very important factor controlling rolling resistance of road vehicle tyres. There are at least three different temperatures that may be considered as important factors controlling thermal conditions of the rolling tyre. The most common measure of the thermal conditions during tyre rolling is ambient air temperature. The other two are: pavement temperature and “tyre” temperature. Tyre temperature is the most difficult...
-
NIEKONWENCJONALNE BADANIA SKUTECZNOŚCI HAMOWANIA W STACJI KONTROLI POJAZDÓW
PublikacjaW artykule przedstawiono niekonwencjonalne badania skuteczności hamowania samochodu na stanowisku diagnostyczny. Na podstawie przeprowadzonych badań określono wpływ ciężaru samochodu na skuteczność hamowania. Dokonano analizy porównania zmierzonego wskaźnika skuteczności hamowania i rzeczywistego wskaźnika skuteczności hamowania dla różnego obciążenia samochodu użytego do badań.
-
Ocena sprawności cyklu roboczego Pojazdu do Usuwania Odpadów z Pojemników na podstawie danych eksploatacyjnych
PublikacjaW artykule przedstawiona została metoda oceny sprawności cyklu roboczego śmieciarki. Wykorzystując dane eksploatacyjne wyznaczono dwa reprezentatywne cykle i na ich podstawie obliczono zarówno sprawność całego cyklu, jak i jego poszczególnych faz. Porównano wartości energii potrzebnej do opróżniania pojemników, energii do zagęszczania odpadów oraz energii z paliwa. Przedstawiono przebiegi mierzonych i obliczonych wartości w czasie...
-
OPINIA TECHNICZNA nr 3/PG/mosty Sprawowanie nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską” Opinia nt. rozwiązań technicznych przedstawionych w projekcie budowlanym przekopu w lokalizacji Nowy Świat - branża mostowa
PublikacjaOpinię przygotowano w ramach prowadzonego nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską”.
-
OPINIA TECHNICZNA nr 5/PG/mosty Sprawowanie nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską” Opinia nt. rozwiązań technicznych przedstawionych w projekcie wykonawczym przekopu w lokalizacji Nowy Świat - branża mostowa
PublikacjaOpinię przygotowano w ramach prowadzonego nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską”.
-
OPINIA TECHNICZNA nr 8/PG/mosty Sprawowanie nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską” Opinia uzupełniająca do 5/PG/mosty w zakresie mechanizmów zastosowanych na przekopie po przedstawieniu przez projektanta wyciągu z obliczeń
PublikacjaOpinię przygotowano w ramach prowadzonego nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską”.
-
Poroelastic Road Surface – a Promising Road Traffic Noise Abatement Solution
PublikacjaRoad surfaces have a direct impact on the generation of noise by rolling tyres, the main and dominant source of noise of moving vehicles, as well as may affect propagation of noise emitted by all noise sources of a vehicle. Thus there is no doubt that pavement should be considered as one of the major potential road traffic noise abatement measure. Low noise pavements of existing types may in new conditions provide up to 8 dB of...
-
Poroelastic Road Surfaces - State of The Art
PublikacjaPoroelastic Road Surfaces (PERS) constitute a specific group of pavements containing a great amount of crumbled rubber. In most cases rubber aggregate constitutes about 20% of the mixture (by weight) and a polyurethane resin is used as a binder. As a result, PERS is characterized by a much higher elasticity than asphalt and a high porosity typical for drainage pavements. Due to this, tire/road noise is greatly reduced and on top...
-
PRZYCZEPY DO BADANIA OPORU TOCZENIA OPON DO SAMOCHODÓW OSOBOWYCH
PublikacjaPrzedstawiono doświadczenia Zespołu Pojazdów Katedry Konstrukcji Maszyn i Pojazdów Wydziału Mechanicznego Politechniki Gdańskiej dotyczące urządzeń badawczych (przyczep) do pomiaru oporu toczenia opon do samochodów osobowych i nawierzchni drogowych. Opisano przyczepy pomiarowe tego typu. Pomiary oporu toczenia opon samochodowych wymuszane są koniecznością osiągania przez pojazd jak największej swojej sprawności...
-
Rehabilitation device supporting active and passive upper limb exercises
PublikacjaThis article presents a mechatronic solution for rehabilitation devices supporting active and passive exercises in persons with motor dysfunctions of the upper limbs in the area of the elbow and shoulder joints. A planar positioner integrated with original software and a control system, served as the basis for creating the present solution. Bellman’s programming method was applied to optimize the motion trajectory of the planar...
-
Results from tests on bolted connection components for evaluation of friction coefficient in various contact conditions
PublikacjaThe main purpose of the work was the analysis and evaluation of the self-locking quality of a bolted joint covered with Xylan 1070 coating, with comparison to the classic bolts lubricated with Molykote compound during assembly. The second part of the work was the verification of the compliance of the bolts and nuts used in the installation with the ASME B1.1 norm.
-
SAMOCHÓD SPORTOWY DUOMOTO NAPĘDZANY DWOMA SILNIKAMI SPALINOWYMI
PublikacjaPrzedstawiono zaprojektowany i zbudowany przez zespół czterech dyplomantów Wydziału Mechanicznego Politechniki Gdańskiej samochód sportowy napędzany dwoma silnikami. Jeden z nich umieszczono z przodu pojazdu. Przekazuje on moment obrotowy na koła osi przedniej poprzez zespolony układ napędowy. Drugi silnik, usytuowany ztyłu pojazdu, w identyczny sposób przekazuje moment napędowy na koła osi tylnej....
-
Simple Computational Methods in Predicting Limit Load of High-Strength Cold-Formed Sections due to Local Buckling: A Case Study
PublikacjaCold-formed thin-walled sections are prone to local buckling caused by residual stresses, geometrical imperfections and inconsistency of material properties. We present a real case of buckling failure and conduct a numerical and experimental study aimed to identify methods capable of predicting such failures. It is important because designers of structures are getting more FEA-oriented and tend to avoid lengthy procedures of cold-formed...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublikacjaThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
The Application of Vibration Recording and Analysis in Tribological Research on Sliding Friction
PublikacjaThe paper reports on a tribological research on the macroscopic manifestation and characteristics of sliding friction. The aim of the task was to measure friction in lubricated sliding contacts and test the interactions between the environment (the test rig) and the experimental friction contact. Friction-induced vibrations were observed and studied as a manifestation of the process. The typical set of velocity and force/torque...
-
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublikacjaThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...
-
TIRE/ROAD NOISE AND TIRE ROLLING RESISTANCE ON PROTOTYPE PERS SURFACE
PublikacjaPoroelastic road surfaces are characterized by low noise of tires running on them.Road pavements of this type are promising solution to problems related to traffic noise in cities and on rural roads. Some technical problems still have to be solved, in particular regarding durability and skid resistance on wet surface. Ongoing and planned works are to contribute to create a quiet, durable and safe road surface, which will become...
-
Tire/Road Noise On Poroelastic Road Surfaces - Results Of Laboratory Measurements
PublikacjaTire/road noise is the most important part of traffic noise for medium and high speed driving both in the case of passenger cars and trucks. The potential to make modification of tires that significantly reduce tire/road noise in nearly over, at least for conventional tires so the only promising action is to improve road pavements. One of the innovative solutions is poroelastic road pavement (PERS) that reduces airflow related...
Rok 2017
-
3D Printing of Metallic Implants
PublikacjaThe fabrication of various elements, solid and open porous structures of stainless steel and Ti alloy is described. The process was started with the design of 3D models in CAD/CAM system. The 3D models were transformed into *.stl files and then the manufacturing process of the real structures by means of the selective laser melting with the SLM Realizer 100 3D printer was made. The paper shows the porous specimens made for possible...
-
Accurate rolling resistance Rolling resistance measurements can be influenced by a number of factors
PublikacjaTire rolling resistance is one of the most difficult-to-measure parameters of the tire/ pavement interface, especially if road measurements are required. First of all, it is necessary to measure a fairly small force in the system that is heavily loaded by other forces and subjected to many adverse effects causing measurement errors. The second problem is related to the fact that tire rolling resistance depends on many factors,...
-
ANALIZA PORÓWNAWCZA DROGI HAMOWANIA MOTOCYKLA Z WŁĄCZONYM I WYŁĄCZONYM UKŁADEM ABS
PublikacjaW artykule przedstawiono wyniki pomiaru drogi hamowania motocykla przy użyciu hamulca koła przedniego, koła tylnego oraz kombinacji obu tych hamulców. Próby intensywnego hamowania motocykla przeprowadzono na suchej nawierzchni asfaltowej z włączonym i wyłączonym układem ABS. Na podstawie zmierzonej drogi hamowania dokonano obliczenia średniego opóźnienia hamowania.
-
Analysis of the possibility of determining the general characteristics using the operational data of a vehicle engine
PublikacjaThe paper presents an analysis of the possibility of determining the general characteristics using the operational data of an engine of refuse collection vehicle. Data acquisition was done by reading information from the CAN network using FMS standard (Fleet Management System), which is widely used in heavy duty vehicles since year 2002. The paper presents the analysis of the expected measurement uncertainties resulting from the...
-
Charakterystyka porównawcza zgazowania drewna bukowego i RDF w reaktorze przeciwprądowym
PublikacjaRozproszone małe układy produkcji ciepła to coraz popularniejszy trend w energetyce. Praca opisuje możliwości zgazowania biomasy i odpadów w reaktorze przeciwprądowym małej mocy. Zgazowanie odpadów jest obiecującą metodą ich utylizacji. W pracy porównano rozkład temperatur uzyskany podczas zgazowania biomasy i WPS dla całej wysokości reaktora. Porównane zostały składy gazu generatorowego oraz jego kaloryczność. Podczas prób badano...
-
Degradation of reference tyres used for CPX measurements
PublikacjaMeasurements of tyre/road noise using the Close Proximity Method are based on reference tyres that are described in ISO/TS 11819-3. The standard specifies two tyres, namely "P1" and "H1" that should be used during measurements. To be used for measurements each tyre must fulfill certain conditions that are listed in the standard. The conditions are related to the tread pattern depth and rubber hardness. During experiments performed...
-
Design of a test bench for determining the general characteristics of an internal combustion engine using a hydraulic power take-off system
PublikacjaThe paper presents a design of an engine test bench, which is used to determine the general characteristics of a truck engine using a power take-off (PTO). PTO drives a hydraulic system that generates a load on the engine at various points in its operation in the power range specified by the hydraulic system. The design allows for stationary and mobile tests with the test bench mounted on the truck, without any modification of...
-
Extended duration running and impulse loading characteristics of an acoustic bearing with enhanced geometry
PublikacjaThis paper presents performance during prolonged running of the acoustic bearing when PZTs are switched off and when they are switched on. The effect of active PZT on shaft’s displacements in X and Y directions is clearly demonstrated. Performance of the acoustic bearing was also assessed when an impulse force was applied to the running shaft at speed. Once again the benefits of having PZTs active are beyond doubt. The instability...
-
Field tests on hydrodynamic and hybrid operation of a bi-directional thrust bearing of a pump-turbine
PublikacjaIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Because of bi-directional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Field Tests on Hydrodynamic and Hybrid Operation of a Bidirectional Thrust Bearing of a Pump-Turbine
PublikacjaIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Due to the bidirectional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Hydrodynamiczne łożyska wzdłużne z warstwą ślizgową z PEEK
PublikacjaMonografia zawiera podsumowanie stanu wiedzy w zakresie hydrodynamicznych łożysk wzdłużnych z polimerową warstwą ślizgową uzupełnione o wyniki badań własnych autora w tym obszarze. W pierwszej części przedstawiono obszerny przegląd znanych z literatury wyników badań, a także opis doświadczeń eksploatacyjnych łożysk z wahliwymi segmentami z pokryciem powierzchni ślizgowej materiałami polimerowymi na bazie PTFE oraz PEEK. Materiały...
-
Improvement of the thrust bearing calculation considering the convectional heating within the space between the pads
PublikacjaA modern thrust bearing calculation tool should consider not only the oil film between pad and rotating collar but also the space between the pads. The oil flow in the space has a significant influence on the oil film inlet temperature, the convectional cooling of pad and collar and should be included in the bearing calculation methods. The authors use a tool developed at Clausthal University of Technology in cooperation with the...
-
Investigation method of large-volume tire with mobile test rig
PublikacjaThe goal of this research is to develop the tire test method and mobile tire test rig. The test rig enables measurement of tire properties as stiffness and viscous damping in vertical direction, and tire–ground characteristics on the asphalt rigid surface. The tire-ground characteristics are measured by force and a torque measurement hub. The design, calibration and the algorithm for calculating the forces in the wheel center are...
-
Liquefaction of macroalgae Enteromorpha biomass for the preparation of biopolyols by using crude glycerol
PublikacjaThis article describes the liquefaction process of macroalgae Enteromorpha with the use of crude glycerol as a solvent and a reagent, aimed at obtaining of new bio-polyols, which are characterized with respect to their chemical structure, physical and thermal properties. Six different biopolyols were prepared. In order to optimize the liquefaction of algal biomass for the best bio-polyol properties, two catalysts (sulfuric or orthophosphoric...