Search
Filters
total: 4465
filtered: 3412
displaying 1000 best results Help
Search results for: LOW-CYCLIC FATIGUE
-
Artificial Neural Network based fatigue life assessment of riveted joints in AA2024 aluminum alloy plates and optimization of riveted joints parameters
PublicationThe objective of this paper is to provide the fatigue life of riveted joints in AA2024 aluminum alloy plates and optimization of riveted joints parameters. At first, the fatigue life of the riveted joints in AA2024 aluminum alloy plates is obtained by experimental tests. Then, an artificial neural network is applied to estimate the fatigue life of riveted lap joints based on the number of lateral and longitudinal holes, punch pressure,...
-
Influence of pitting corrosion on fatigue and corrosion fatigue of ship and offshore structures. Part II: Load - pit crack interaction
PublicationIn the paper has been discussed influence of stresses on general corrosion rate and corrosion pit nucleation and growth rate, whose presence has been questioned by some authors but accepted by most of them. Influence of pit walls roughness on fatigue life of a plate suffering pit corrosion and presence of so called "non damaging" pits which never lead to initiation of fatigue crack, has been presented. Possibility of prediction...
-
The influence of combination of binding agents on fatigue properties of deep cold in-place recycled mixtures in Indirect Tensile Fatigue Test (ITFT)
PublicationThe publication presents fatigue properties of cold recycled mixtures for eight combinations of binding agents (cement and bituminous emulsion). Cold recycled mixtures were evaluated in Indirect Tensile Fatigue Test (ITFT) at the temperature of 20 C in controlled stress mode. As a function of horizontal stress, fatigue life is strongly influenced by combination of the binding agents. When fatigue life is analyzed as a function...
-
Tensile and Fatigue Behavior of Additive Manufactured Polylactide
PublicationThis article presents the results of monotonic tensile and fatigue tests conducted on commercial polylactide or polylactic acid (PLA). The results of fatigue tests for this material present in the literature are limited, especially for additive manufactured elements. The specimens were manufactured using the injection molding and the fused filament fabrication (FFF) method. The FFF specimens were divided into five subgroups, depending...
-
Artificial neural network based fatigue life assessment of friction stir welding AA2024-T351 aluminum alloy and multi-objective optimization of welding parameters
PublicationIn this paper, the fracture behavior and fatigue crack growth rate of the 2024-T351 aluminum alloy has been investigated. At first, the 2024-T351 aluminum alloys have been welded using friction stir welding procedure and the fracture toughness and fatigue crack growth rate of the CT specimens have been studied experimentally based on ASTM standards. After that, in order to predict fatigue crack growth rate and fracture toughness,...
-
Some problems of slide bearing material fatigue evaluation.
PublicationA slide bearing alloy resistance against fatigue failures have been investigated for three different lubricants, different heat loadings and different stress ratio κ values. The research methods and data handling procedures for determination of particular parameter effects on fatigue strength have been described and analysed for experiments that were set and performed in laboratory tester SKMR-2. Main and interaction effects of...
-
Driver Fatigue and Road Safety on Poland's National Roads
PublicationThis paper presents an overview of factors causing driver fatigue as described in the literature. Next, a traffic crash database for 2003–2007 is used to identify the causes, circumstances and consequences of accidents caused by driver fatigue on Poland’s national roads. The results of the study were used to build a model showing the relationship between the concentration of road accidents and casualties, and the time of day. Finally,...
-
System setup and software for cyclic, staircase and square wave voltammetry measurements
PublicationHardware dedicated for electrochemical measurement sometimes does not allow performing certain voltammetry experiments. Staircase and square wave voltammetry, techniques which have many advantages comparing with standard voltammetric techniques, are rarely implemented in software controlling electrochemical measuring equipment. These methods, however, can be relatively easy realized with some addition...
-
The Effect of Water and Frost on Fatigue Life of Asphalt Concrete
PublicationThis paper presents testing of fatigue life of asphalt concrete that has been subjected to action of water and frost. Simulation of water and frost action was based on the original AASHTO T283 method and its modification. The original method was modified in such a way that instead of a single freeze-thaw cycle, 50 and 150 cycles were applied. Fatigue life was measured in the indirect tensile fatigue test in the Nottingham asphalt...
-
ENERGY ANALYSIS OF THE PROPULSION SHAFT FATIGUE PROCESS IN A ROTATING MECHANICAL SYSTEM PART II IDENTIFICATION STUDIES – DEVELOPING THE FATIGUE DURABILITY MODEL OF A DRIVE SHAFT
PublicationThe article presents a continuation of research carried out concerning identification of energy consequences of mechanical fatigue within a propeller shaft in a rotating mechanical system, while working under conditions of the loss of the required alignment of shaft lines. Experimental research was carried out on a physical model reflecting a full-sized real object: i.e., the propulsion system of the ship. It is proven, by means...
-
Mechanical properties of polyvinyl chloride-coated fabric under cyclic tests
PublicationThe aim of the present paper is to propose a method of laboratory tests necessary for the identification of mechanical properties of the coated fabric. The material parameters of the coated fabric AF 9032 are specified on the basis of the uniaxial and biaxial tensile tests. For the identification process, the techniques based on the least squares methods are used. Additionally, the uniaxial and biaxial cyclic tests are performed...
-
Asphalt Overlay Enhancement with Fatigue High-Performing Multiaxial Geocomposite
PublicationThe use of gecomposite incorporating multiaxial geogrid and non-woven fabric of high bitumen retention in asphalt overlays results in the increase of life of the designed pavement structure. Such an approach can offer an opportunity to increase the fatigue life (higher traffic capacity) without the need to increase asphalt overlay thickness or to reduce the thickness of asphalt overlay without reduction of pavement life eventually....
-
Influence of pitting corrosion on fatigue and corrosion fatigue of ship structures. Part I: pitting corrosion of ship structures.
PublicationThe paper is a literature survey focused on pitting corrosion and its influence on fatigue of ship and offshore steels. Mechanisms of short- and long-term pitting corrosion in marine environment have been described including pit nucleation and growth phases. Some models of pit growth versus time of exposure have been presented. Some factors which influence the pit growth have been discussed briefly.
-
Fatigue strength determination of ship structural joints. Part I - Analytical methods for determining fatigue strength of ship tructures
PublicationSpectacular accidents at sea which have happened for a few last years show that hull structures of contemporary sea-going ships are not perfect and must be systematically improved. Fatigue strength is one of the groups of strength problems which affect design of contemporary ship's structures and greatly contribute in their improvement process. In this paper several approaches to estimation of fatigue life of hull structural...
-
A Convenient Synthesis of Monocationic 1-[(Cyclic amidino)methyl]thymines
Publication1-[(Cyclic amidino)methyl]thymines have been conveniently synthesized from thymine in a three-step procedure via 1-cyanomethyl- and 1-[(thiocarbamoyl) methyl]thymines. The above synthetic intermediates were obtained in good yields by improved methods.
-
Fracture Surface Topography Parameters for S235JR Steel Adhesive Joints After Fatigue Shear Testing
PublicationThis paper presents the experimental results of a study investigating the effect of holes and notches made on the overlap ends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets bonded with Araldite 2024-2 epoxy adhesive were tested. For comparative reasons, static shear strength tests and high-cycle fatigue strength tests were performed. Adhesive-filled joints having three holes, each with a diameter...
-
Fatigue behaviour of SLM maraging steel under variable-amplitude loading
PublicationOne of the most challenging issues for additive manufactured materials is fatigue endurance. Engineering components often operate under complex, variable amplitude loadings, in which existing technological imperfections promote fatigue cracks growth and damage of elements eventually. In this study the effects of different variable-amplitude strain levels on fatigue life, 18Ni300 steel was tested. The work presents various behaviours...
-
Load capacity of steel-aluminium brackets under static and cyclic laboratory tests
PublicationThe aim of the research is the laboratory investigation of steel-aluminium brackets employed to fasten lightweight curtain walls to building facilities. Static pressure, suction forces, and cyclic loads parallel to end plates (horizontal – to simulate wind influence) were applied in the study. The steel-aluminium brackets were tested on a reinforced concrete substrate made of C30/37 concrete class to simulate the real working conditions....
-
ENERGY ANALYSIS OF PROPULSION SHAFT FATIGUE PROCESS IN ROTATING MECHANICAL SYSTEM PART I TESTING SIGNIFICANCE OF INFLUENCE OF SHAFT MATERIAL FATIGUE EXCITATION PARAMETERS
PublicationThe article discusses the problem of mathematical modelling of energy conversion processes in a rotating mechanical system for the purpose of identifying fatigue states of propulsion shafts in this system. A simplified physical model of the analysed system, constructed in an appropriate scale, has made the basis for the experimental research. The research programme took into consideration mechanical fatigue excitation of the model...
-
Problems of analytical determination of journal bearing bush fatigue strength estimates
PublicationProblems connected with determination of stress distribution in sliding layer of thinwalled bearing bushes, investigated in bearing fatigue test rigs, have been presented. Using an example of plain bearings tested in the fatigue machine SMOK (built at the Gdask University of Technology) problems with obtaining a convergence of iterative procedure for determining the fatigue strength estimators of bearing alloy surface layer are...
-
The influence of food phytochemicals on cyclic phosphodiesterase 4 (PDE4) activity
PublicationCyclic phosphodiesterase 4 (PDE4) belongs to family of cyclic phosphodiesterases, which are expressed predominantly in inflammatory cells, airway smooth muscles, cardiovascular tissues and brain. Inhibitors of this family of enzymes found medicinal applications as antidepressants, antiinflamatory drugs (mainly in airway diseases) or antiasthmatics (Ibudilast). PDE4 inhibitors are also being tested for preventing the development...
-
Investigating the Effects of Geometrical Parameters of Re-Entrant Cells of Aluminum 7075-T651 Auxetic Structures on Fatigue Life
PublicationIn this study, the effects of two geometrical parameters of the re-entrant auxetic cells, namely, internal cell angle (θ) and H/L ratio in which H is the cell height, and L is the cell length, have been studied on the variations of Poisson’s ratio and fatigue life of Aluminum 7075-T6 auxetic structures. Five different values of both the H/L ratio and angle θ were selected. Numerical simulations and fatigue life predictions have...
-
The Possibilities of Improving the Fatigue Durabilityof the Ship Propeller Shaft by Burnishing Process
PublicationHeavily loaded structural elements operating in a corrosive environment are usuallyquickly destroyed. An example of such an element is a ship propeller operating in a seawaterenvironment. This research presents a fatigue resistance test performed on elements operating inseawater. Different processing parameters applied on the samples in particular were compared withthe specimens whose surface had been burnished differently and...
-
Stress analysis of the bridge hangers in terms of the fatigue verification
PublicationThe paper presents the results of numerical stress analysis of the bridge rod hangers. Two types of hangers were taken into account, i.e. the bolted hanger and the welded hanger. A detailed FEM shell models of the connection area between the hanger and the bridge span have been developed. Local stress concentration effects have been investigated in terms of fatigue verification.
-
An investigation on residual stress and fatigue life assessment of T-shape welded joints
PublicationThis paper aims to quantitatively evaluate the residual stress and fatigue life of T-type welded joints with a multi-pass weld in different direction. The main research objectives of the experimental test were to test the residual stress by changing direction along with multiple wielding passes and determine the fatigue life of the welded joints. The result shows that compressive residual stress increases in the sample gradually...
-
Effect of bending-torsion on fracture and fatigue life for 18Ni300 steel specimens produced by SLM
PublicationIn this study, different fracture surfaces caused by fatigue failure were generated from 18Ni300 steel produced by selective laser melting (SLM). Hollow round bars with a transverse hole were tested under bending-torsion to investigate the crack initiation mechanisms and fatigue life. Next, the post-failure fracture surfaces were examined by optical profilometer and scanning electron microscope. The focus is placed on the relationship...
-
4-(Cyclic-amidino)phenols. Preparation and Use in a Diamidine Synthesis
PublicationThe Pinner synthesis was applied to the prepn. of phenols 4-substituted with cyclic amidines in high yields from readily available 4-HOC6H4C(OMe):NH.HCl and aliph. diamines. An alternative attempt was made to convert 4-HOC6H4CSNH2 to 4-(1,4,5,6-tetrahydro-5-hydroxy-2-pyrimidinyl)phenol. A procedure for the prepn. of 3,6-bis(4-hydroxyphenyl)-1,2,4,5-tetrazine is reported. The syntheses of 2,4-bis[4-(4,5-dihydro-1H-imidazol-2-yl)phenoxy]pyrimidine...
-
Driver fatigue detection method based on facial image analysis
PublicationNowadays, ensuring road safety is a crucial issue that demands continuous development and measures to minimize the risk of accidents. This paper presents the development of a driver fatigue detection method based on the analysis of facial images. To monitor the driver's condition in real-time, a video camera was used. The method of detection is based on analyzing facial features related to the mouth area and eyes, such as...
-
Effect of elliptical defect orientation on the durability of specimens subjected to cyclic bending
PublicationThis work presents the effect of elliptical defects orientation on the durability of specimens made of C45 steel. Three kinds of specimens with elliptical defects in the form of a one-sided notch oriented at different angles 45, 60, and 90 degrees were subjected to cyclic bending (R=-1). The stress state analysis was performed using local and non-local methods to determine an equivalent amplitude of stress, and then the results...
-
Application of acoustic emission for detection of fatigue microdemage in main and crank bearings for diesel engines
PublicationThe article presents reasons for applying the acoustic emission (AE) to detect fatigue microdamage in main bearings and crank bearings of ship main engines. Problem of determination of the fatigue life for slide bearing bushes was characterized in general. There were demonstrated properties of the objects of research, which were bushings made of the MB58 alloy, as well as an overall description of the research. It was shown that...
-
Stiffness change of abdominal prosthesis Optomesh™ under cyclic loading
PublicationAbdominal prostheses are used in humans for abdominal wall strengthening or reconstruction. From the mechanical point of view they are membranes, so their basic mechanical property is tensile stiffness. This property is experimentally identified for a selected implant, OptomeshTM. The obtained results are described herein. Uni-axial simple and cyclic tension tests are a basis for the analysis. Both kinds of tests allowed to distinguish...
-
Antecedents and outcomes of social media fatigue
PublicationPurpose – This study aims to explore which of four chosen factors (i.e. privacy concerns, FoMO, self-disclosure and time cost) induce a feeling of strain among Facebook users in terms of social media fatigue (SMF), and if this occurs, whether it further influences such outcomes as discontinuance of usage (DoU) and interaction engagement decrement (IED). Design/methodology/approach – Through an online structured questionnaire, empirical...
-
An image processing approach for fatigue crack identification in cellulose acetate replicas
PublicationThe cellulose acetate replication technique is an important method for studying material fatigue. However, extracting accurate information from pictures of cellulose replicas poses challenges because of distortions and numerous artifacts. This paper presents an image processing procedure for effective fatigue crack identification in plastic replicas. The approach employs thresholding, adaptive Gaussian thresholding, and Otsu binarization...
-
Strain sequence effect on fatigue life and fracture surface topography of 7075-T651 aluminium alloy
PublicationThe paper studies the effect of strain-loading sequence on fatigue lifetime and fracture surface topographies in 7075-T651 aluminum alloy specimens. Fatigue tests were performed in two ways: (i) constant-amplitude loading and (ii) two series of variable amplitude loading with non-zero mean strain values. The topography of the fatigue fractures was measured over their entire surfaces with the help of an optical confocal measurement...
-
Laboratory fatigue assessment of large geocomposite-reinforced double-layered asphalt concrete beams
PublicationGeosynthetic reinforcement of asphalt layers has been used for several decades. Evaluation of the influence of these materials on pavement fatigue life is still ongoing, especially for new types of geocomposites. This paper presents the evaluation of fatigue performance of large asphalt concrete beams reinforced with a new type of composite in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions...
-
Laboratory fatigue assessment of large geocomposite-reinforced double-layered asphalt concrete beams
PublicationGeosynthetic reinforcement of asphalt layers has been used for several decades. Evaluation of the influence of these materials on pavement fatigue life is still ongoing, especially for new types of geocomposites. This paper presents the evaluation of fatigue performance of large asphalt concrete beams reinforced with a new type of composite in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions...
-
Advanced fatigue and rutting characterisation of Polish asphalt mixtures based on the VECD model and viscoplastic shift model
PublicationThe advanced asphalt mixture performance-related specifications (AM-PRS) recently developed in USA can allow an optimisation of the design process of asphalt pavements thanks to the possibility to fully take into account the intrinsic material properties. In this study, four typical Polish mixtures, i.e. a Stone Mastic Asphalt (SMA) for wearing course, two mixtures for binder course with neat bitumen or Polymer modified Bitumen...
-
Entire fracture surface topography parameters for fatigue life assessment of 10H2M steel
PublicationIn this paper, the entire fracture surface approach was used to assess an effect of 280,000 h of exploitation under internal pressure of 2.9 MPa and high temperature of 540 °C on the fatigue response of 10H2M (10CrMo9–10) power engineering steel. The mechanical testing was carried out on the hourglass specimens produced from the as-received, unused pipeline and the same material after long-time exploitation. The uniaxial tensile...
-
Analysis of the cyclic load-unload-reload tests of VALMEX aged fabric
PublicationThe paper presents mechanical response of the VALMEX fabric during the cyclic loading-unloading and re-loading experiments. Two types of the aged material used for nearly 20 years as the roofing of the Forest Opera in Sopot (Poland) have been tested. The results have been separately obtained for the warp and fill di-rections. The comparative analysis has revealed that the material aged in service is more durable in the fill di-rection,...
-
Experimental study of the impact of notches and holes made in the front edge of adherends on the properties of static and fatigue strength of adhesive joints
PublicationThe paper presents the results of experimental studies aimed at determining the effect of holes and notches at the front edge of adherends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets joined with Araldite 2014-2 epoxy adhesive were tested. Comparative tests of static strength in the shear test as well as high-cycle fatigue strength tests were carried out. Joints with three holes with a diameter...
-
COMMENTS ON EXISTING ANALYTICAL SOLUTIONS TO THE WAVE-INDUCED CYCLIC RESPONSE OF A POROUS SEABED OF INFINITE THICKNESS
PublicationThis paper deals with the wave-induced cyclic response of a porous seabed (by means of oscillating parameters: pore-fluid pressure, soil displacement components, effective normal stress and shear stress components) due to a surface sinusoidal water-wave propagating over a seabed of infinite thickness. The main existing analytical solutions to the governing problem are critically discussed, pointing out their meaningful errors and...
-
Fatigue fracture morphology of AISI H13 steel obtained by additive manufacturing
PublicationThe paper focuses on researching the effect of fatigue loading on metallic structure, lifetime, and fracture surface topographies in AISI H13 steel specimens obtained by selective laser melting (SLM). The topography of the fracture surfaces was measured over their entire area, according to the entire total area method, with an optical three-dimensional surface measurement system. The fatigue results of the SLM 3D printed steel...
-
Fatigue Performance of Double-Layered Asphalt Concrete Beams Reinforced with New Type of Geocomposites
PublicationThe reinforcement of asphalt layers with geosynthetics has been used for several decades, but proper evaluation of the influence of these materials on pavement fatigue life is still a challenging task. The presented study investigates a novel approach to the reinforcement of asphalt layers using a new type of geogrid composite, in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions is bonded...
-
The conception of energetic investigations of the multisymptom fatigue of the simple mechanical systems' constructional materials
PublicationThe article presents the basic assumptions of the research project aimed, as the main scientific purpose, an identification of the slow-changeable energy processes surrounding the high-cycle fatigue of constructional materials within the plain mechanical system, especially the marine one, for diagnostic purposes. There is foreseen an application of alternative diagnostic methods based on energetic observations of the multi-symptom,...
-
Fatigue Bending of V-Notched Cold-Sprayed FeCoCrNiMn Coatings
PublicationCold-spray coatings were produced by FeCoCrNiMn high-entropy alloy powders deposited on carbon steel substrate. The coatings were realized at intermediate temperature and high pressure (at 1100 °C and 7 MPa). The coating microstructure was characterized by scanning electron microscopy and X-ray diffraction, revealing a very dense deposition and high flattening ratio of the splatted particles. This had a large influence on the...
-
Prediction of the fatigue lifetime of PUR structural elements using a combined experimental-numerical approach
PublicationThis paper presents a method for estimating the fatigue life of polyurethane elastomeric components. A rubber replacement - polyurethane of hardness 80ShA commonly used in vibration damping systems, for example, in motor vehicle suspensions, was used for the study. A metal-rubber bushing component was selected for analysis, and numerical analysis was carried out along with a fatigue model proposal based on a modification of the...
-
Progress in non-isocyanate polyurethanes synthesized from cyclic carbonate intermediates and di- or polyamines in the context of structure–properties relationship and from an environmental point of view
PublicationCommercially, polyurethanes are produced by the reaction of diisocyanates, polyols (polyester or polyether) and low molecular weight chain extender. Toxicity, moisture sensitivity and phosgene-based synthesis of diisocyanates resulted in investigations focused on obtaining the non-isocyanate polyurethanes (NIPUs). This work presents the review of synthesis and structure–properties relationship of non-isocyanate polyurethanes obtained...
-
Fracture surface topography investigation and fatigue life assessment of notched austenitic steel specimens
PublicationThe objectives of this study were to investigate the fracture surface topography of X8CrNiS18-9 austenitic stainless-steel specimens for different loadings and notch radii and to supplement the knowledge about the fracture mechanisms for fatigue performance. Cases with three different values of the notch radius ρ and the stress amplitude σa were analysed. The fracture topographies were quantified by the areas over their entire...
-
Morphology of damage inflicted on brittle polymer in lubricated contact under cyclic static load
PublicationIn this article morphology of damage inflicted on the polymethylmethacrylate (PMMA) plate in static point lubricated contact with a ball made of five different materials under cyclic normal load has been presented. It is argued that the counterface material and lubricating film play an important role in the damage process and the extent of damage inflicted in the PMMA plate.
-
Synthesis and structural characterization of bio-based bis(cyclic carbonate)s for the preparation of non-isocyanate polyurethanes
PublicationBio-based cyclic carbonates are of significant research interest as monomers for non-isocyanate polyurethane (NIPU) synthesis. This research describes the synthesis of a series of five-membered bis(cyclic carbonate)s using bio-based polyether polyols (PO3G) with different molecular weights (250, 650 and 1000 g mol−1) and carbon dioxide as green feedstocks. The utilization of CO2 as a source of carbon in the chemical reaction is...