Filters
total: 320
filtered: 283
-
Catalog
Chosen catalog filters
Search results for: CO2 MEASUREMENTS
-
Selected Aspects of Pavement Texture Influence on Tire Rolling Resistance
PublicationTire rolling resistance has a significant influence on fuel consumption in cars and trucks and on CO2 emissions. Rolling resistance depends on the tire construction, pavement texture and stiffness, as well as environmental and traffic conditions. This article presents a pilot study on the impact of pavement texture on the rolling resistance of passenger car tires. Reasons why Mean Profile Depth is not a good descriptor of pavement...
-
Magazynowanie energii elektrycznej
PublicationŚwiatowa gospodarka opiera się na energii, dlatego wymaga się, aby energia była łatwo dostępna, stosunkowo tania, a jej dostawy niezawodne. Zmiany klimatyczne powodują jednak, że wzrastają wymogi dotyczące redukcji emisji CO2, a co za tym idzie – zwiększenia udziału „zielonej energii” pochodzącej ze źródeł odnawialnych. Ramy europejskiej polityki klimatyczno-energetycznej do roku 2030 zakładają m.in. redukcję emisji ditlenku węgla...
-
An improved method for flow boiling heat transfer with account of the reduced pressure effect
PublicationIn the paper are presented the results using the authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data to investigate the sensitivity of the in-house developed model. In the work are presented the results of calculations obtained using the semi-empirical model on selected experimental flow boiling data of the refrigerants: R134a, R1234yf,...
-
Exsolution of Ni nanoparticles on the surface of cerium and nickel co-doped lanthanum strontium titanate as a new anodic layer for DIR-SOFC. Anti-coking potential and H2S poisoning resistance of the prepared material
PublicationThe aim of this study was to evaluate a new catalytic material for biogas fueled DIR-SOFC. This material was a perovskite-type SrTiO3 doped with La, Ce and Ni of a general formula La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-σ (LSCNT). Additional preparation steps were undertaken to promote a nickel exsolution process. Heat post-treatment of powders in a humidified H2 resulted in an intensive growth of nickel nanoparticles (NPs) while the temperature...
-
Wytwarzanie energii elektrycznej - diagnoza i terapia
PublicationW artykule przeanalizowano stan i dalszy rozwój krajowego sektora wytwarzania energii elektrycznej w świetle najnowszych raportów Międzynarodowej Agencji Energetycznej, wskazujących potencjalne trendy i perspektywy w światowej energetyce. Na tle przewidywanego wzrostu zapotrzebowania na energię elektryczną wskazano na możliwość istotnego ograniczenia emisji CO2 drogą zastąpienia przestarzałych, nieefektywnych...
-
Nuclear power plant as a source of electrical energy and heat
PublicationIn this paper certain issues concerning usage of nuclear power plants as sources of not only electric power but also thermal energy will be discussed. For such a solution appeals most of all the need to limit harmful emissions of gases (including CO2) and ashes, which come from the process of burning fossil fuels, as well as the raising demand for network heat and chill. Additionally combined heat and power production brings measurable...
-
Influence of cavitation intensity on the relative cavitation resistance of laser processed C45 carbon steel
PublicationPraca przedstawia badania względnej odporności kawitacyjnej we wstępnym okresie niszczenia laserowo przetopionej 6 kW laserem CO2 stali C45. Badania odporności kawitacyjnej wykonano na stanowisku z wirującą tarczą. Na erodowanej przetopionej warstwie powierzchniowej określono trzy obszary o różnej intensywności oddziaływania obciążeń kawitacyjnych. Określano wielkość odkształceń plastycznych w analizowanych obszarach, spowodowanych...
-
A new cold-active β-galactosidase from Arthrobacter sp. S3* - gene cloning, overexpression, purification and properties
PublicationA psychrotrophic bacterium producing a cold-active β-galactosidase was isolated from Spitsbergen soil and classified as Arthrobacter sp. S3*. The gene encoding β-galactosidase was isolated from the genomic DNA library, sequenced, cloned, expressed in Escherichia coli, purified by ion exchange chromatography and characterized. The Arthrobaster sp. S3* β-galactosidase is a homotrimeric enzyme composed of 74,4 kDa subunits. It is...
-
Properties of Nasicon-based CO2 sensor with Bi8Nb2O17 reference electrode
PublicationGas sensors are useful for the carbon dioxide concentration monitoring in many applications. The major challenge is to develop a potentiometric sensor working without the necessity of a reference gas and without a need of the reference electrode encapsulation. Important issue is a selection of reference electrode material, which should provide stable reference potential. For example as reference electrode material in sensor based...
-
Perspektywy wykorzystania gazu ziemnego do produkcji energii elektrycznej w Polsce
PublicationW artykule omówiono podstawowe przesłanki, które mogą decydować o wykorzystaniu technologii gazowych do produkcji energii elektrycznej w Polsce. Przedstawiono aktualną strukturę wytwarzania energii elektrycznej w krajowym systemie elektroenergetycznym. Zostały przedstawione prognozy wzrostu zapotrzebowania na energię elektryczną w perspektywie 2030 r. Wskazano na konieczność zmiany bazy paliw dla systemu elektroenergetycznego....
-
Use of imidazolium ionic liquids for carbon dioxide separation from gas mixtures
PublicationNowoczesnym podejściem do separacji tlenku węgla (IV) z mieszanin gazowych jest zastosowanie cieczy jonowych jako materiału absorpcyjnego. Niemierzalna prężność par i możliwość modyfikacji budowy kationu i wyboru anionu cieczy jonowych sprawiają, że związki te mogą zastąpić obecnie stosowane aminy. Przedstawiono wpływ struktury chemicznej cieczy jonowych, ciśnienia oraz temperatury na efektywność absorpcji CO2 i innych gazów w...
-
Carbon dioxide photoconversion. The effect of titanium dioxide immobilization conditions and photocatalyst type.
PublicationBadanie efektywności procesu fotokonwersji CO2 prowadzono w fazie gazowej w obecności promieniowania UV-Vis, pary wodnej oraz fotokatalizatorów. Zbadano wpływ wybranych parametrów tj. masa, temperatura i czas suszenia fotokatalizatora oraz rodzaj nośnika na efektywność procesu fotokonwersji. Wyznaczono optymalne parametry prowadzenia procesu oraz przedstawiono wstępne wyniki badań w obecności fotokatalizatorów modyfikowanych nanoczastkami...
-
Computational Fluid Dynamics Simulation of Gas–Liquid Multiphase Flow in T-junction for CO2 Separation
PublicationThe article presents the results of a computational fluid dynamics (CFD) analysis of gas-liquid multiphase flow. The simulation was conducted using CFD code and the Euler–Euler approach. The presented study relates to the non–reactive, steady-state, turbulent flow of water and carbon dioxide mixture in a 3D pipe. Separation phenomenon between phases is observed. The solution was obtained using a mixture model. Different values...
-
Opracowanie potencjometrycznej wieloczujnikowej platformy wykonanej całkowicie w technologii All-Solid-State do jednoczesnego oznaczania kilku jonów w roztworach wodnych
PublicationW pracy przedstawiono charakterystykę i konstrukcje różnych elektrod jonoselektywnych (EJS), a także opisano elektrodę odniesienia i jej funkcję. Przybliżono możliwości zastosowania EJS do monitorowania śladowych ilości ołowiu (II) w otoczeniu kopalni rud cynku i ołowiu, oraz jako biowskaźnik stanu pacjenta w czasie wstrząsu septycznego. Opisano wieloczujnikowe platformy potencjometryczne (WPP) w technologii All-Solid-State (ASS). W...
-
Modelowanie rozwoju regionalnych systemów energetycznych ze szczególnym uwzględnieniem bioenergii.
PublicationPraca miała na celu opracowanie metodyki modelowania rozwoju systemów energetycznych na skalę regionalną z uwzględnieniem bioenergii oraz mechanizmów wspierania odnawialnych i skojarzonych źródeł energii, jak również systemu handlu uprawnieniami do emisji CO2. W wyniku rozwiązania zadania optymalizacyjnego określona została struktura produkcji i zużycia nośników energii w zadanym horyzoncie czasowym wraz z udziałem poszczególnych...
-
Opór toczenia opon samochodowych
PublicationOpór toczenia opon samochodowych jest jednym z istotnych parametrów charakteryzujących współpracę opon samochodowych z nawierzchnią jezdni. jego wartość wpływa na zużycie paliwa a przez to na koszt transportu samochodowegooraz na osiągi pojazdów, takie jak prędkość maksymalna czy zdolność przyspieszania. W zależności od warunków ruchu zmniejszenie oporu toczenia o 10% powoduje zmniejszenie zużycia paliwa o2-4%. Zmniejszenie zużycia...
-
Stanowisko do aktywnej termografii dynamicznej do diagnostyki medycznej
PublicationW artykule omówiono budowę zestawu diagnostycznego metodą aktywnej termografii dynamicznej w medycznych aplikacjach takich jak: diagnostyka oparzeń, monitoring gojenia się ran pooperacyjnych oraz monitoring w kardiochirurgii. Podstawowy zestaw składa się z układu formowania wymuszenia termicznego w postaci nadmuchu schłodzonej mieszaniny gazów CO2 oraz powietrza lub tylko schłodzonego powietrza, układu akwizycji sekwencji termograficznych,...
-
Balancing Energy Inputs/Outputs and GHG Emissions for Sustainable Wastewater Treatment – a Case Study
PublicationThe aim of the study is a model-based evaluation of the selected operating modes and technological upgrades on the energy balance and greenhouse gas (GHG) emissions in a large wastewater treatment plant in the city of Slupsk (northern Poland). The considered scenarios focus on energy savings for aeration, increasing energy recovery via biogas cogeneration and reduction of the CO2 equivalent emission from both direct processes (related...
-
Effects of Laser Remelting at Cryogenic Conditions on Microstructure and Wear Resistance of the Ti6Al4V Alloy Applied in Medicine
PublicationThe titanium and its alloys can be subjected to surface treatment, including laser treatment. In this work a new laser treatment at cryogenic conditions of Ti6Al4V alloy has been described. The work has been aimed at establishing whether such surface treatment could be suitable for implants working under wear in biological corrosive environment. The remelting has been made with the use of CO2 continuous work laser at laser power...
-
Biogas upgrading using supported liquid membranes based on ionic liquids
PublicationZastosowanie cieczy jonowych osadzonych w porach nośników polimerowych bądź ceramicznych jest nowoczesnym podejściem do separacji ditlenku węgla z mieszanin gazowych. Znikoma prężność par cieczy jonowych i możliwość modyfikacji budowy kationu i wyboru anionu wchodzących w skład cieczy jonowych sprawiają, że związki te mogą zastąpić obecnie stosowane w procesach separacji aminy. W publikacji przedstawiono wpływ struktury chemicznej,...
-
Composite GFRP U-shaped footbridge
PublicationThe paper presents proposals for the use of glass fiber reinforced polymer composites for the construction of engineering objects, known and commonly used in the shipbuilding industry. An example of a pedestrian footbridge was used in this case, which, despite the considerable thickness of the structural material, was made using infusion technology in one production cycle. The designed and produced footbridge span is durable, dynamically...
-
OPTYMALIZACJA UDZIAŁU ELEKTROWNI JĄDROWYCH W KRAJOWEJ STRUKTURZE WYTWARZANIA ENERGII ELEKTRYCZNEJ W PERSPEKTYWIE DO 2060 ROKU
PublicationW niniejszym referacie przedstawiono wyniki analizy systemowej z wykorzystaniem modelu MARKAL. Analiza ta miała na celu określenie optymalnego udziału elektrowni jądrowych, na tle innych opcji technologicznych, w krajowej strukturze wytwarzania energii elektrycznej w perspektywie do 2060 roku. Kryterium optymalizacyjnym była minimalizacja kosztów dostawy energii elektrycznej od wytwórcy do odbiorcy końcowego, z uwzględnieniem ograniczeń...
-
Pyrolysis of RDF and Catalytic Decomposition of the Produced Tar in a Char Bed Secondary Reactor as an Efficient Source of Syngas
PublicationOne of the technical limitations of refuse-derived fuel (RDF) pyrolysis is the high content of tar in its gas products. In order to resolve this problem, a two-stage RDF pyrolysis with a catalyst based on char from RDF pyrolysis is proposed. This paper presents the results of municipal waste pyrolysis beginning in an oven heated to 480 °C and ending with catalytic tar cracking carried out in the temperature range from 800 to 1000...
-
Pyrolysis Combined with the Dry Reforming of Waste Plastics as a Potential Method for Resource Recovery—A Review of Process Parameters and Catalysts
Publication: Emissions of greenhouse gases and growing amounts of waste plastic are serious environmental threats that need urgent attention. The current methods dedicated to waste plastic recycling are still insufficient and it is necessary to search for new technologies for waste plastic management. The pyrolysis-catalytic dry reforming (PCDR) of waste plastic is a promising pro-environmental way employed for the reduction of both CO2 and...
-
Badania cieczy jonowych jako absorbentów gazów
PublicationPrzedmiotem pracy jest efektywność przenikania CO2 oraz CH4 przez ciekłe membrany z cieczami jonowymi osadzonymi na nośnikach polimerowych i szklanych oraz pomiary stabilności tych membran w temperaturze 283-298 K.Badania objęły ciecze jonowe będące kombinacją kationu [CnMIM], zawierającego różną długość podstawnika alkilowego n=2-6 oraz różnych anionów: Tf2N, TfO, BF4 i PF6. Jako nośniki SILMs zastosowano materiały polimerowe:...
-
A study of a compact high-efficiency zero-emission power plant with oxy-fuel combustion
PublicationThis paper discusses the application of global trends in gas cycles technology using oxy-fuel combustion. This is followed by a demonstration of a design solution for a new cycle with two enhanced energy-converting devices, namely a wet combustion chamber and a spray-ejector condenser. The proposed gas and steam cycle unit is contained within a single turbine, whose benefits combine those offered by gas turbines (high inlet temperatures)...
-
Pyrrole azocrown ethers. Synthesis, complexation, selective lead transport and ion-selective membrane electrode studies
PublicationOtrzymano nowe, 21-członowe, lipofilowe etery koronowe z jednostką pirolową i dwoma grupami azowymi jako składowymi makrocyklu. Właściwości kompleksujące tych nowych oraz dwóch wcześniej otrzymanych makrocykli zbadano w acetonitrylu. Ligandy te zostały użyte jako jonofory w badaniach konkurencyjnego transportu równomolowej mieszaniny jonów metali: Co2+, Ni2+, Cu2+, Zn2+, Cd2+, Ag2+, Pb2+ w układzie woda(pH 4.9)/chloroform/woda(pH...
-
Investigation of an elutable N-propylphosphonic acid chitosan derivative composition with a chitosan matrix prepared from carbonic acid solution
PublicationPorous chitosan composites using CO2 dissolution procedure and including water soluble N-propylphosphonic chitosan derivative (p-CHI) were obtained and characterized. In contrast to the control material, composites containing modified chitosan distinguished by a rapid moisture absorption and good adhesion to the skin. The FTIR analysis confirmed the presence of propylphosphonic group in the structure of the polymer. The porosity...
-
Modelling of the Heat Flux Density Distribution for Laser Beam Welding
PublicationGreat interest of the laser beam welding in industry is a new theoretical task, making planning the welding procedure specification and the quality control of welded joints easier. Estimating and calculating the dimensions of a weld pool and temperature distribution near weld mainly concern heat source modelling. In the presented work calculations of welding pool shape and thermal field for cylindrical-powered-normally model of...
-
Final report on noise and rolling resistance
PublicationWork Package 6 deals with environmental impacts of PERS use, including noise and rolling resistance. This report covers preliminary noise tests performed in the laboratory and at the road test sites. The obtained results indicate that PERS material reduce noise considerably - up to 12 dB in comparison to SMA16 reference surface. Noise reduction properties are especially visible in the case of factory produced PERS slabs supplied...
-
The Influence of Selected Parameters of Numerical Modelling on Strains and Stresses at Weld Toe Notch
PublicationLatest development in the field of welding technology and prefabrication enabled massive production of thin-walled sandwich structures. Multi-layered sandwich structures are fabricated with the use of high-power CO2 lasers, friction welding, arc welding, hybrid welding, or other technique designed for the special purpose. Steel or aluminium alloy plates with thickness between 1 and 5 mm are connected by internal stiffeners. Strength...
-
Influence of ethylene glycol on CaCO3 particles formation via carbonation in the gas-slurry system
PublicationStrącanie węgalnu wapnia przebiegało w układzie gaz-zawiesina w reakcji wodorotlenku wapnia z dwutlenkiem węgla. Proces precypitacji był prowadzony w obecności glikolu etylenowego. Użyty dodatek organiczny zmieniał lepkość mieszaniny reakcyjnej oraz rozpuszczalność dwutlenku węgla i węgalnu wapnia, co miało wpływ na warunki precypitacji CaCO3. Wzrost stężnia glikolu etylenowego w mieszaninie reakcyjnej powodował większe zużycie...
-
Wykorzystanie fourierowskiej spektroskopii w podczerwieni do badania stężenia gazów wylotowych z tlenkowego ogniwa paliwowego zasilanego biogazem
PublicationW dzisiejszych czasach bardzo ważne jest pozyskiwanie energii ze źródeł odnawialnych i bezpiecznych dla środowiska. Jedną z obiecujących technologii są tlenkowe ogniwa paliwowe (ang. Solid Oxide Fuel Cell, SOFC). Stanowią one bezpieczną i ekologiczną alternatywę dla energii uzyskanej z paliw kopalnych. SOFC charakteryzuje się sprawnością energetyczną na poziomie 45-60 %, podczas gdy sprawność klasycznych elektrowni cieplnych nie...
-
Analiza składu fazy gazowej wytwarzanej podczas fermentacji ciemnej
PublicationFermentacja ciemna umożliwia otrzymywanie bio-wodoru z substratów pochodzenia biologicznego, np. z biomasy ligno-celulozowej. Kontrola i właściwe sterowanie przebiegiem procesu fermentacji ciemnej wymaga bieżącego monitoringu składu powstającej fazy gazowej. W niniejszej pracy przedstawiono metodykę analizy składu fazy gazowej z wykorzystaniem techniki GC-TCD-FID. Zaproponowana metodyka umożliwia oznaczenie następujących gazów...
-
Sustainable energy system combined biogas-feedSolid Oxide Fuel Cell and Microalgae technology
PublicationIn the new frontier of energy and environmental safety, new efficient and clean safe energy conversion systems are required. In this sense, the present work is framed within the context of Circular Economy and proposes a multidisciplinary study for the development of more efficient, economically viable and non-polluting energy conversion systems, based on the synergetic combination of different technologies: fuel cells, biofuels,...
-
Effect of plasma sprayed and laser re-melted Al2O3 coatings on hardness and wear properties of stainless steel
PublicationCommercially available austenic stainless steel substrate was coated with commercially available, raw Al2O3 powder applied by means of plasma spraying method and then re-melted with CO2 laser beam of various parameters. Tribological and mechanical properties of the 120 J/mm and 160 J/mm laser re-melted coatings were compared with the tribological and mechanical properties of the “as-sprayed” coating. The influence of the laser...
-
Hydrogen Production Mechanism in Low-Temperature Methanol Decomposition Catalyzed by Ni3Sn4 Intermetallic Compound: A Combined Operando and Density Functional Theory Investigation
PublicationHydrogen production from methanol decomposition to syngas (H2 + CO) is a promising alternative route for clean energy transition. One major challenge is related to the quest for stable, cost-effective, and selective catalysts operating below 400 °C. We illustrate an investigation of the surface reactivity of a Ni3Sn4 catalyst working at 250 °C, by combining density functional theory, operando X-ray absorption spectroscopy, and high-resolution...
-
Combined operation of 900MW power plant with the ORC through the bleed steam extraction point and CO2 recovery system
PublicationThe work presented here is aimed at utylisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90 C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach...
-
The Influence of Modelling Material Zones on Strains and Stresses at Weld Toe Notch
PublicationThe latest development in the field of welding technology enabled prefabrication of thin-walled sandwich structures in an industrial scale. Sandwich structures fabricated of steel, or aluminium alloy plates and stiffeners are welded with the use of hi-power CO2 lasers. Strength analysis of such structures with the use of finite element method needs proper material modelling.In this paper the material model of steel sandwich panel...
-
Wykorzystanie systemu komputerowego ALEP-PL w planowaniu rozwoju lokalnych systemów energetycznych
PublicationZaprezentowano autorski system komputerowy ALEP-PL, który wspomaga proces planowania rozwoju lokalnych systemów energetycznych. Narzędzie zostało przygotowane z uwzględnieniem metodyki planowania zaawansowanego. System składa się z serwisu internetowego, bazy danych i modułów logiki biznesowej. Serwis internetowy został stworzony w technologii ASP.NET z użyciem środowiska Visual Studio 2010 i serwera baz danych MS SQL Server 2008...
-
The optimization of CuxO microwires synthesis for improvement in photoelectrochemical performance
PublicationOne of the most important challenges in the fabrication of CuxO microstructures via the electrochemical method is formation of long, regular and well-packed microwires with good adhesion on the Cu substrate and to achieve better photoelectrochemical properties, which can be potentially applied in solar-driven water splitting and CO2 conversion to light hydrocarbons. In this paper, Cu2O photoelectrode has been fabricated by direct...
-
Encapsulation of Cs3Bi2Br9 perovskite photocatalyst with polythiophene for prolonged activity in oxidizing and humid environment
PublicationDespite their growing popularity in modern technology, halide perovskites suffer from susceptibility to oxidation, limiting their applications. Our aim was to enhance Cs3Bi2Br9 perovskite's performance in humid environments through polythiophene encapsulation. This extended its lifespan while preserving photocatalytic abilities, as demonstrated in toluene decomposition experiments. We confirmed the stability of Cs3Bi2Br9 encapsulated...
-
Theoretical and Economic Evaluation of Low-Cost Deep Eutectic Solvents for Effective Biogas Upgrading to Bio-Methane
PublicationThis paper presents the theoretical screening of 23 low-cost deep eutectic solvents (DESs) as absorbents for effective removal of the main impurities from biogas streams using a conductor-like screening model for real solvents (COSMO-RS). Based on thermodynamic parameters, i.e., the activity coefficient, excess enthalpy, and Henry’s constant, two DESs composed of choline chloride: urea in a 1:2 molar ratio (ChCl:U 1:2), and choline...
-
Studies on the utilization of post-distillation liquid from Solvay process to carbon dioxide capture and storage
PublicationIn this work, a method of precipitated calcium carbonate production from the post-distillation liquid created in the Solvay process and waste carbon dioxide was proposed and investigated. Precipitation was carried out in a model solution of calcium chloride containing ammonia at various molar ratios in relation to Ca2+ ions, while gaseous carbon dioxide was supplied to the reactor as a pure gas or as a mixture with air. It was...
-
Effect of Microplastics Pollution on Hydrogen Production from Biomass: A Comprehensive Review
PublicationHydrogen production from biomass and organic wastes is considered as a potential alternative energy source and is known as a clean and CO2-free fuel energy carrier. H2 is considered very promising among the other energy sources; therefore, the effective conversion of biomass and organic solid waste to this secondary energy source is urgently sought. As a result, it is of importance to assess the impact of the existence of microplastics...
-
Operation of the 900 MW power plant with the ORC supplied from three heat sources
PublicationThe chapter is aimed at utilisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90°C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach to increase...
-
Preparation and characterization of genipin cross-linked porous chitosan–collagen–gelatin scaffolds using chitosan–CO2 solution
PublicationNovel porous scaffolds composed of chitosan, collagen and gelatin were prepared by the multistep procedure involving final freeze-drying and characterized. To eliminate the need for residual acid removal from the material after drying, carbon dioxide saturation process was used for chitosan blend formulation. The use of CO2 for chitosan dissolution made the scaffold preparation process more reproducible and economically sustainable....
-
A review on homogeneous and heterogeneous catalytic microalgal lipid extraction and transesterification for biofuel production
PublicationExtracting lipids from microalgal biomass presents significant potential as a cost-effective approach for clean energy generation. This can be achieved through the chemical conversion of lipids to produce fatty acid methyl esters via transesterification. The extraction mainly involves free fatty acids, phospholipids, and triglycerides, and requires less energy, making it an attractive option for satisfying the growing demand for...
-
Negative carbon dioxide gas power plant integrated with gasification of sewage sludge
PublicationOne of the primary objectives of the negative carbon dioxide gas power plant (nCO2PP) is to develop an innovative technology confirming the possibility of the use of sewage sludge to produce electricity while having a positive impact on the environment. In this paper, a mathematical model is presented to estimate thermodynamic parameters of the system in relation to the gasification process and changes in such parameters in the...
-
Modeling of low calorific gas burning in a deficient oxygen environment and high-temperature oxidizer
PublicationThe experimental research will be performed using the experimental facility with a combustion chamber. The oxygen concentration in combustion oxidizers will be varied from 21% by volume (normal) air to 2%. The test combustion chamber will be fed with propane or methane as the reference fuel, then with low calorific fuels as test gases obtained by mixing various combustible components, e.g. H2, CH4, CO, and neutral gases, e.g. N2,...