Filters
total: 1261
filtered: 1078
displaying 1000 best results Help
Search results for: NUMERICAL METHOD
-
Mathematical model and numerical calculations of the pelagic trawl system
PublicationW pracy przedstawiono matematyczny model ruchu środka ciężkości zestawu do trałowania pelagicznego wraz z wyznaczaniem jego parametrów geometrycznych. Pokazano także sposób rozwiązania i przykładowe wyniki obliczeń numerycznych. Opracowany program komputerowy może być wykorzystywany do wyznaczania optymalnych parametrów pracy dla zapewnienia bezpiecznych, efektywnych i ekologicznych połowów pelagicznych
-
NUMERICAL SIMULATIONS OF GAP FLOW ABOVE ROTATING DISK
PublicationA rotating disk can be considered a basic configuration for the investigati ons of the impact of various conditions on the flow through the clearance between the s hrouded turbine blade and the casing. Numerical calculations using Fine/Turbo Numeca were conducted to examine the influence of the rotational velocity and the pressure differ ence across the disk on the flow conditions, especially the mass flow through the clearance....
-
On the validation of the LS-DYNA Geo Metro numerical model
PublicationThe paper presents experiences gained during work with numerical model of Geo Metro vehicle used for simulations of crash tests with road safety barriers. Attention is drawn to the subject of tire/wheel breakage during collision events. Some methods for improvement of the model are presented in the paper. Several results for the normative vehicle numerical tests are introduced. Simulations were carried out using LS-DYNA finite...
-
In Situ Verification of Numerical Model of Water Hammer in Slurries
PublicationThis paper presents a numerical model of transient flow in a pressure slurry pipeline network with verification based on in situ measurements. The model, primarily verified in laboratory conditions, has been extended and applied to the case of a large and complex slurry pipeline network in Poland. In the model, the equivalent density concept was applied. In situ experiments were performed for various unsteady flow episodes, caused by...
-
Wind Conditions in Urban Layout – Numerical and Experimental Research
PublicationThis paper presents research which compares the numerical and the experimental results for different cases of airflow around a few urban layouts. The study is concerned mostly with the analysis of parameters, such as pressure and velocity fields, which are essential in the building industry. Numerical simulations have been performed by the commercial software Fluent, with the use of a few different turbulence models, including...
-
An Experimental and Numerical Analysis of Water Hammer Phenomenon in Slurries
PublicationThe analysis of slurry transportation in pressure pipelines is important both from practical and theoretical point of view. Due to the nature of the medium, the number of problems arising in the course of design, operation, measurements and mathematical modeling is much higher compared to the cases where the flowing liquid is homogeneous. The equations describing the flow are more complex, and higher number of the parameters is...
-
Comparative testing of numerical models of river ice jams
PublicationIce processes in general, and ice jams in particular, play a dominant role in the hydrologic regime of Canadian rivers, often causing extreme floods and affecting the life cycle of many aquatic, terrestrial, and avian species. Various numerical models have been developed to help simulate the formation and consequences of these very dynamic and often destructive jam events. To test and compare the performance of existing models,...
-
Numerical modeling of ice jam formation in the Włocławek reservoir
PublicationArtykuł opisuje zjawisko powstawania zatoru lodowego w zbiorniku przepływowym przy użyciu dwuwymiarowego modelu DynaRICE. Analizowany proces został przeanalizowany na przykładzie zatoru lodowego, który utworzył się na zbiorniku Włocławek w syczniu 1982 roku. Przeprowadzone obliczenia pokazały, że zator utworzyła się z lodu powierzchniowego. Efekt termiczny i tworzenie się śryżu w zbiorniku został pominięty jako drugorzędny. Wyniki...
-
Numerical modeling of the nonlinear wave propagation in a bubble layer
PublicationRozważano zagadnienie propagacji fali wewnątrz warstwy z pęcherzykami. Omówiono model matematyczny, przedstawiono przykładowe wyniki badań teoretycznych. Analizowano zmiany ciśnienia wewnątrz warstwy, falę odbitą i bieżącą w ośrodku otaczającym, badano gęstość widmową mocy. Badania teoretyczne przeprowadzono dla różnych grubości warstwy, koncentracji pęcherzyków i wartości parametrów fali padającej.
-
Confined granular flow in silos : experiments and numerical investigation
PublicationW monografii opisano niektóre charakterystyczne zjawiska mające miejsce podczas przepływów silosowych materiałów sypkich. Wykonano badania doświadczalne oraz obliczenia numeryczne celem wyjaśnienia zjawisk. Doświadczenia wykonano w dużych i małych silosach. Obliczenia wykonano przy zastosowaniu metody elementów skończonych opartej na hipoplastycznym modelu konstytutywnym dla materiałów sypkich.
-
Experiments and numerical analyses for composite RC-EPS slabs
PublicationW artykule przedstawiono wyniki doświadczalne i numeryczne dla kompozytowych płyt złożonych z żelbetu i styropianu. Wykonano doświadczenia dla płyt w skali 1:1 podczas zginania. Wyniki doświadczalne zostały modelowane stosując 2 różne modele: sprężysto-plastyczny i połączony sprężysto-plastyczny z degradacja sztywności. Oba model zostały wyposażone w długość charakterystyczna mikrostruktury. Osiągnięto dobra zgodność miedzy...
-
Steel-fibrous concrete -experiments and a numerical discrete model
PublicationW książce przedstawiono wyniki doświadczalne i numeryczne dotyczące rys w elementach betonowych wzmocnionych włóknami stalowymi dla różnych problemów brzegowych quasi-statycznych. Obliczenia wykonano przy zastosowaniu własnego oryginalnego modelu sieciowego. W modelu beton z włóknami stalowymi był modelowany na poziomie mezo. W obliczeniach uwzględniono strefy kontaktu miedzy kruszywem a zaczynem oraz włóknami a zaczynem.
-
Diagnostics of bolted lap joint using guided wave propagation
PublicationThe paper presents numerical and experimental analyses of elastic waves propagation in a bolted lap joint. In experimental investigations condition assessment of the joint was performed with the use of symmetric waves excited by a piezoactuator. Numerical calculations were conducted in commercial finite element method software Abaqus. The influence of number of bolts and the value of the initial stress on recorded signals was examined....
-
Impact of diffusion coefficient averaging on solution accuracy of the 2D nonlinear diffusive wave equation for floodplain inundation
PublicationIn the study, the averaging technique of diffusion coefficients in the two-dimensional nonlinear diffusive wave equation applied to the floodplain inundation is presented. As a method of solution, the splitting technique and the modified finite element method with linear shape functions are used. On the stage of spatial integration, it is often assumed that diffusion coefficient is constant over element and equal to its average...
-
Implementation of Haar wavelet, higher order Haar wavelet, and differential quadrature methods on buckling response of strain gradient nonlocal beam embedded in an elastic medium
PublicationThe present investigation is focused on the buckling behavior of strain gradient nonlocal beam embedded in Winkler elastic foundation. The first-order strain gradient model has been combined with the Euler–Bernoulli beam theory to formulate the proposed model using Hamilton’s principle. Three numerically efficient methods, namely Haar wavelet method (HWM), higher order Haar wavelet method (HOHWM), and differential quadrature method...
-
A Mesh Deformation Technique Based on Solid Mechanics for Parametric Analysis of High-Frequency Devices With 3-D FEM
PublicationIn this paper, a versatile technique for mesh defor- mation is discussed, targeted at the electromagnetic (EM) field simulation of high-frequency devices using the 3-D finite element method (FEM). The approach proposed applies a linear elasticity model to compute the displacements of the internal mesh nodes in 3-D when the structure geometry is changed. The technique is compared with an alternative approach...
-
Research on protection mechanisms of Resilient Packet Ring Network.
PublicationPaper describes iSteering - a new method to control traffic in case of RPR network failure. There's comparison of packet wrapping, steering and our proposed method iSteering, which can be used in case of transmitter/receiver or fiber failure. Numerical analysis for even and random traffic flow has been made in order to compare packet wrapping, steering and iSteering. The results of all the tests are included.
-
Modal FEM Analysis of Ferrite Resonant Structures
PublicationThe finite-element method (FEM) is applied for modal analysis of ferrite-loaded spherical resonators. To improve the efficiency of the numerical calculations, the body-of-revolution (BOR) technique is utilized. Due to the frequency-dependent ferrite permeability, FEM leads to a nonlinear eigenvalue problem that is challenging to solve. To this end, Beyn’s method is proposed. The effectiveness of the proposed approach is confirmed...
-
Buckling of thin-walled columns accounting for initial geometrical imperfections
PublicationThe paper is devoted to the effect of some geometrical imperfections on the critical buckling load of axially compressed thin-walled I-columns. The analytical formulas for the critical torsional and flexural buckling loads accounting for the initial curvature of the column axis or the twist angle respectively are derived. The classical assumptions of theory of thin-walled beams with non-deformable cross-sections are adopted. The...
-
Large deformation finite element analysis of undrained pile installation
PublicationIn this paper, a numerical undrained analysis of pile jacking into the subsoil using Abaqus software suit has been presented. Two different approaches, including traditional Finite Element Method (FEM) and Arbitrary Lagrangian–Eulerian (ALE) formulation, were tested. In the first method, the soil was modelled as a two-phase medium and effective stress analysis was performed. In the second one (ALE), a single-phase medium was assumed...
-
Novel approach to modeling spectral-domain optical coherence tomography with Monte Carlo method
PublicationNumerical modeling Optical Coherence Tomography (OCT) systems is needed for optical setup optimization, development of new signal processing methods and assessment of impact of different physical phenomena inside the sample on OCT signal. The Monte Carlo method has been often used for modeling Optical Coherence Tomography, as it is a well established tool for simulating light propagation in scattering media. However, in this method...
-
Stability and limit load analysis of a cold-formed channel section column
PublicationThe paper presents stability and limit load analysis of a steel column 1440 mm high of a cold-formed channel section, subjected to a combination of compression and bending. Experimental results were compared to the resistance of a code procedure and to the outcome of numerical non-linear analysis. Comparison was made of numerical solutions by means of static (Riks) and dynamic (Explicit and Implicit) methods. Perfectly elastic...
-
The Proposal to “Snapshot” Raim Method for Gnss Vessel Receivers Working in Poor Space Segment Geometry
PublicationNowadays, we can observe an increase in research on the use of small unmanned autonomous vessel (SUAV) to patrol and guiding critical areas including harbours. The proposal to “snapshot” RAIM (Receiver Autonomous Integrity Monitoring) method for GNSS receivers mounted on SUAV operating in poor space segment geometry is presented in the paper. Existing “snapshot” RAIM methods and algorithms which are used in practical applications...
-
Detection of Delamination in Laminate Wind Turbine Blades Using One-Dimensional Wavelet Analysis of Modal Responses
PublicationThis paper demonstrates the effectiveness of a nondestructive diagnostic technique used to determine the location and size of delamination in laminated coatings of wind turbine blades. This is realized based on results of numerical and experimental investigations obtained by the use of the finite element method (FEM) and laser scanning vibrometry (LSV). The proposed method is based on the one-dimensional continuous wavelet transform...
-
A Parallax Shift Effect Correction Based on Cloud Height for Geostationary Satellites and Radar Observations
PublicationThe effect of cloud parallax shift occurs in satellite imaging, particularly for high angles of satellite observations. This study demonstrates new methods of parallax effect correction for clouds observed by geostationary satellites. The analytical method that could be found in literature, namely the Vicente et al./Koenig method, is presented at the beginning. It approximates a cloud position using an ellipsoid with semi-axes...
-
A Method of Fast and Simultaneous Calibration of Many Mobile FMCW Radars Operating in a Network Anti-Drone System
PublicationA market for small drones is developing very fast. They are used for leisure activities and exploited in commercial applications. However, there is a growing concern for accidental or even criminal misuses of these platforms. Dangerous incidents with drones are appearing more often, and have caused many institutions to start thinking about anti-drone solutions. There are many cases when building stationary systems seems to be aimless...
-
A high-accuracy complex-phase method of simulating X-ray propagation through a multi-lens system
PublicationThe propagation of X-ray waves through an optical system consisting of many X-ray refractive lenses is considered. For solving the problem for an electromagnetic wave, a finite-difference method is applied. The error of simulation is analytically estimated and investigated. It was found that a very detailed difference grid is required for reliable and accurate calculations of the propagation of X-ray waves through a multi-lens...
-
Professor Jan Kruszewski-Majewski (1929-2012)
PublicationIn this obituary, we present the life and achievements of an outstanding Polish scientist, Professor Jan Kruszewski-Majewski, who passed away in 2012. Professor Jan Kruszewski-Majewski was one of the pioneers in introducing modern numerical methods in mechanics. He created and developed an original, Polish method of modellings called the rigid finite element method. He was ont only an outstanding scientist, but also a person of...
-
Diagnostics of historic columns using wave propagation
PublicationThis paper presents a numerical analysis of elastic wave propagation in columns of historical buildings for diagnostics purposes. Numerical calculations were performed using the finite element method in the Abaqus software package. The analysis was carried out for three types of brick columns: a full column, a column filled with debris, and a column empty inside. The excitation was in the form of a wave packet and signals of propagating...
-
Applying response surface method to optimize the performance of a divergent-chimney solar power plant
PublicationOne of the effective tools to generate electricity from solar energy is Divergent-chimney solar power plant (DSPP). Divergent and cylindrical chimneys of solar power plants have different performances considering turbine pressure drop ratio (ft). For the first time, the divergent angle (DA) and solar radiation (SR) interaction effects on 〖ft〗_opt are discussed through applying the Computational Fluid Dynamics (CFD) and Response...
-
A procedure for elastoplastic hardening function identification.
PublicationThe inverse analysis method for identifying a nonlinear hardening function,which governs a plastic yielding of soil and rock materials in the framework of elastoplastic theory is presented. A concept of two stage finite element based on spatial discretization of computational space and hardening function space is introduced. The proposed inverse analysis can be classified as the output least squares method. The Levenberg Marquard...
-
Fatigue of titanium alloy Ti6Al4V with diamond structure obtained by Laser Power Bed Fusion method
PublicationThis paper presents the results of fatigue tests conducted on Ti6Al4V titanium alloy with diamond structure obtained by the Laser Power Bed Fusion method. Samples used in tests were printed with porosities: 81%, 73%, 50%, 34% and near-zero porosity. Samples were subjected to cyclic tests with a constant stress amplitude. The number of cycles until sample failure was registered. Obtained fatigue test results made it possible to...
-
Domain Reduction in Hybrid Technique for Electromagnetic Wave Scattering Problems
PublicationThis paper proposes a combination of the field matching technique, finite element method and generalized impedance matrix, the main idea of which is to reduce the computational domain by surrounding a scatterer with the smallest convex shape and applying the field matching technique. This approach can be applied for arbitrary shaped scatterers and types of materials and allows for the reduction of the computational domain. In order...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART IV) MODELLING THE HEATING PROCESS AND DETERMINING THE SERVICEABILITY OF HYDRAULIC COMPONENTS DURING THE STARTING-UP IN LOW AMBIENT TEMPERATURE
PublicationDesigners of hydraulically driven machines and devices are obliged to ensure during design process their high service life with taking into account their operational conditions. Some of the machines may be started in low ambient temperature and even in thermal shock conditions (due to delivering hot working medium to cold components). In order to put such devices into operation appropriate investigations, including experimental...
-
Analysis of wave propagation in a bolted steel joint
PublicationThe paper presents results of numerical and experimental investigations of elastic wave propagation in a bolted single-lap joint. The research was carried out for both symmetric and antisymmetric Lamb wave modes. In experimental studies the PZT transducers were used to excite and register wave propagation signals. The controlled value of the torque during measurements was ensured by the use of high precision torque wrenches. Numerical...
-
Elastic wave propagation for condition assessment of steel bar embedded in mortar
PublicationThis study deals with experimental and numerical investigations of elastic wave propagation in steel bars partially embedded in mortar. The bars with different bonding lengths were tested. Two types of damage were considered: damage of the steel bar and damage of the mortar. Longitudinal waves were excited by a piezoelectric actuator and a vibrometer was used to non-contact measurements of velocity signals. Numerical calculations...
-
Inverse Analysis as a Key Element of Safety Assessment under the Snow Load For The Large Suspension Roofs Structure
PublicationThe paper presents a concept and realization of monitoring system for the Silesian Stadium in Chorzow. The idea of the system lies in fusion of structure monitoring with a calibrated numerical FEM model [1]. The inverse problem is solved. On the base of measured selected displacements, the numerical FEM model of the structure combined with iterative method, develops the current snow load distribution. Knowing the load, we can calculate...
-
Numerical heat transfer model in skin burn depth simulations
PublicationW artykule przedstawiono numeryczny model wymiany ciepła zachodzącej w tkance skórnej . Wyniki symulacji na modelu zostały porównane z wynikami pomiarów In vivo na zwierzętach.
-
Numerical Simulations of Laser and Hybrid S700MC T-Joint Welding
Publication -
Computational Techniques in Numerical Simulations of Arc and Laser Welding Processes
Publication -
Measurements and numerical simulations of laser hardening and remelting thermal cycles
Publication -
A numerical scale to assess the outcomes of metabolic/bariatric surgery (NOMS)
Publication -
APPLICATION OF NUMERICAL SIMULATIONS ON X10CRWMOVNB9-2 STEEL MULTILAYER WELDING
Publication -
Numerical study of lasing modes of periodically structured active nanowires
Publication -
Numerical approximations of parabolic functional differential equations on unbounded domains
PublicationSkonstruowano schematy różnicowe zagadnień początkowych dla nieliniowych parabolicznych równań różniczkowo funkcyjnych. Przedstawiono twierdzenie o oszacowaniu błędu rozwiązań przybliżonych dla równań różnicowo funkcyjnych typu Volterry z niewiadomą funkcją kilku zmiennych. Udowodniono twierdzenie o zbieżności jawnych schematów różnicowych. Podano przykłady numeryczne.
-
Experimental and numerical studies of double corrugated steel arch panels
Publication -
Numerical modeling of force and contact networks in fragmented sea ice
Publication -
Numerical modelling of thermodynamics and dynamics of sea ice in the Baltic Sea
Publication -
Experimental study and numerical calculations in the analysis of thin-walled structures
Publication -
A COMPUTATIONAL ALGORITHM FOR THE NUMERICAL SOLUTION OF NONLINEAR FRACTIONAL INTEGRAL EQUATIONS
Publication