displaying 1000 best results Help
Search results for: ELASTIC MODULUS DETERMINATION
-
Determination of pitting corrosion stage of stainless steel by galvanodynamic impedance spectroscopy
PublicationThis paper investigates the methodology for differentiation of multistep process of pitting corrosion of AISI 304 stainless steel in the environment of iron (III) chloride. Measurements were performed using Galvanodynamic Electrochemical Impedance Spectroscopy (GDEIS). Application of this methodology allowed monitoring of natural corrosion process without external current (IDC = 0A) nor potential perturbation of the system. Applied...
-
Determination of time delay between ventricles contraction using impedance measurements
PublicationThe paper presents a novel approach to assessment of ventricular dyssynchrony basing on multichannel electrical impedance measurements. Using a proper placement of electrodes, the sensitivity approach allows estimating time difference between chambers contraction from over determined nonlinear system of equations. The theoretical considerations which include Finite Element Method simulations were verified using measurements on...
-
Determination of equivalent axle load factors with the use of strain energy of distortion
PublicationThe paper proposes a new method for calculation of equivalent axle load factors based on the analysis of strain energy of distortion induced in road pavements by traffic loads. The main advantage of the method is the more accurate calculation of the effects of multiple axles and super single versus dual tyres. The methodconsiders the location of critical points, at which strain energy of distortion reaches extreme values. When...
-
The effect of the temperature change rate on determination of the criticalpitting temperature of stainless steels
PublicationPrzedstawiono wyniki badań wpływu szybkości zmian temperatury na wyznaczaną krytyczną temperaturę korozji wżerowej. Badania stali 316L przeprowadzono metodą termometrii cyklicznej. Stwierdzono, że zwiększenie szybkości zmian temperatury związane jest ze zwiększeniem wyznaczonej temperatury krytycznej. Zależność krytycznej temperatury korozji wżerowej od szybkości korozji ma charakter liniowy. Wartości krytycznej temperatury korozji...
-
Preparation of environmental samples for gas chromatographic determination of selected organic pollutants
PublicationOpisano różne metody izolacji i wzbogacania zanieczyszczeń organicznych z ciekłych, gazowych i stałych próbek środowiskowych. Opisano konstrukcję i testowanie nowych systemów do przygotowania próbek oraz ich zastosowanie w połączeniu z chromatografią gazową do oznaczania zanieczyszczeń organicznych w póbkach rzeczywistych.
-
Derivatisation in gas chromatographic determination of acidic herbicides inaqueous environmental samples.
PublicationW pracy przedstawiono przegląd literaturowy dotyczący wykorzystania derywatyzacji w oznaczaniu herbicydów kwasowych w wodnych próbkach środowiskowych za pomocą chromatografii gazowej. Omówiono główne typy reakcji (transestryfikacja, estryfikacja, sililowanie, alkilacja, alkilacja ekstraktywna i pirolityczna), które powodują utworzenie pochodnych, łatwych do analizy techniką chromatografii gazowej. Scharakteryzowano także...
-
Determination of chlorophenols and phenoxyacid herbicides in the Gulf of Gdańsk, Southern Baltic Sea.
PublicationChlorofenole i kwasy fenoksyoctowe to dwie grupy zanieczyszczeń środowiska, obecne w wodach powierzchniowych. Kwasy fenoksyoctowe, ze względu na dobrą rozpuszczalność w wodzie, stosunkowo łatwo przedostają się do zbiorników wodnych i innych elementów środowiska. W ramach pracy postanowiono zbadać zawartość chlorofenolu i kwasów fenoksyoctowych oraz ich sezonowe zmiany w wodach ujścia Wisły i Zatoki Gdańskiej. Opracowano metodę...
-
Solvent residue determination in Uncaria Tomentosa Bark by HS-GC technique
PublicationPrzedstawiono wyniki oznaczeń pozostałości rozpuszczalników organicznych w preparacie uzyskanym z kory liany U. Tomentosa, wykorzystywanej do produkcji farmaceutyków i dodatków do żywności. 1,1,2-trichloroeten oraz dichlorometan są powszechnie stosowane do usunięcia z kory kilku grup alkaloidów o znanych właściwościach biologicznych, co umożliwia zbadanie pozostałych jej związków. Ilościowe oznaczanie tych rozpuszcalników jest...
-
Determination of acetaldehyde and acrolein in raw spirits by capillary isotachophoresis after derivatization
PublicationW publikacji opisano optymalizację i przygotowanie nowej procedury oznaczania acetaldehydu i akroleiny w spirytusach surowych z wykorzystaniem techniki izotachoforezy kapilarnej (ITP). Aldehydy - związki niejonowe poddawane są derywatyzacji wodorosiarczynem sodu. Zaprezentowana metoda analityczna charakteryzuje się granicą oznaczalności na poziomie 0,03 ul/cm3 100% EtOH dla akroleiny oraz 0,54 ul/cm3 100% EtOH dla acetaldehydu....
-
Empirical formulas for determination of the propagation loss in urban radio access links
PublicationOpisano wielowariantowy model empiryczny tłumienia propagacyjnego przeznaczonego do analizowaniai projektowania radiowych systemów dostępwych w warunkach zabudowy miejskiej, opracowanego na podstawie obszernych pomiarów tego tłumienia w rzeczywistych warunkach takiej zabudowy. Scharakteryzowano przydatność użytkową tego modelu.
-
Analytical procedures for PAH and PCB determination in water samples - error sources
PublicationW pracy przedstawiono poszczególne etapy procedury analitycznej wykorzystywanej do oznaczania analitów z grupy WWA i PCB w próbkach wody. Pokazano jakie problemy występują podczas oznaczania wyżej wymienionych analitów i jaki mogą mieć wpływ na końcowy wynik analizy.
-
Sources of errors associated with the determination of PAH and PCB analytes in water samples
PublicationW pracy przedstawiono problemy związane z oznaczaniem analitów z grupy WWA i PCB w próbkach wody. Zidentyfikowano źródła błędów. Szczególną uwagę zwrócono na:- proces adsorpcji analitów na ściankach szklanych naczyń używanych w trakcie obróbki i przechowywania próbek,- wpływ etapu odparowywania nadmiaru rozpuszczalnika z ekstraktów na odzysk analitów,- wpływ materiału, z którego jest wykonana kolumienka ekstrakcyjna (szkła, polietylenu)...
-
Polychlorinated biphenyls (PCBs) and polychlorodibenzo-p-dioxins (PCDDs) determination in disposable baby diapers with the application of natural deep eutectic solvent
PublicationIn this work a new method involving solvent extraction of porous membrane-packed solid samples (SE-PMSS) coupled to gas chromatography-mass spectrometry (GC–MS) has been developed for the determination of six polychlorinated biphenyls (PCBs) and five polychlorodibenzo-p-dioxines (PCDDs) in disposable baby diapers. In that aim, a terpenoid-based natural deep eutectic solvent (NADES) composed of carvone and camphor in a 1:1 M ratio...
-
Deep eutectic solvent-based shaking-assisted extraction for determination of bioactive compounds from Norway spruce roots
PublicationPolyphenolic compounds play an essential role in plant growth, reproduction, and defense mechanisms against pathogens and environmental stresses. Extracting these compounds is the initial step in assessing phytochemical changes, where the choice of extraction method significantly influences the extracted analytes. However, due to environmental factors, analyzing numerous samples is necessary for statistically significant results,...
-
Optimization of capillary isotachophoretic method for determination of major macroelements in blue honeysuckle berries (Lonicera caerulea L.) and related products
PublicationA reliable and repeatable isotachophoretic method for the simultaneous determination of K+, Na+, Ca2+, Mg2+ and ammonium in berries of different blue honeysuckle cultivars was developed. The usefulness of the complex-forming equilibria in determining the cations mentioned above was studied. The addition of 7.5 mM 18-crown-6 and 2 mM α-hydroxyisobutyric acid to sulfuric acid enhanced the separation capacity of the leading electrolyte....
-
Ultrasound-Assisted Solvent Extraction of a Porous Membrane Packed Sample for the Determination of Tobacco-Specific Nitrosamines in the Replacement Liquids for E-Cigarettes
PublicationThe content of tobacco-specific nitrosamines (TSNAs) possessing carcinogenic properties has been an important area of research since replacement liquids were introduced for e-cigarettes. A method for determining N′-nitrosonornicotine (NNN), 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone (NNK), N′-nitrosoanatabine (NAT), and N′-nitrosoanabasine (NAB) in replacement liquids for electronic cigarettes was developed using liquid chromatography–tandem...
-
Method for the determination of carboxylic acids in industrial effluents using dispersive liquid-liquid microextraction with injection port derivatization gas chromatography–mass spectrometry
PublicationThe paper presents a new method for the determination of 15 carboxylic acids in samples of postoxidative effluents from the production of petroleum bitumens using ion-pair dispersive liquid-liquid microextraction and gas chromatography coupled to mass spectrometry with injection port derivatization. Several parameters related to the extraction and derivatization efficiency were optimized. Under optimized experimental conditions,the...
-
Determination of modifier contents in polymer-modified bitumens and in samples collected from the roads using high performance gel permeation/size exclusion chromatography
PublicationThis paper describes application of high performance gel permeation/size exclusion chromatography (HP-GPC/SEC) for the determination of content of polymer modifiers in modified road bitumens. The obtained results were compared with the measurements based on the procedure recommended by the American Association of State Highway and Transportation Officials, which employs Fourier transform mid-infrared spectroscopy (mid-IR FTIR)....
-
Experimental determination of general characteristic of internal combustion engine using mobile test bench connected via Power Take-Off unit
PublicationThe general characteristics of the engine include information about the regions of the engine's operating area that are most efficient, where specific fuel consumption reaches the smallest values. Economic operation based on those characteristics can contribute to a significant reduction of fuel consumption and consequently less pollutant emissions and lower costs. The paper presents an experimental method of determination of general...
-
Separation and determination of the group-type composition of modern base and lubricating oils with a wide range of polarity, especially emitted to the environment
PublicationLubricating oils are composed of base oils (>85% v/v) and enriching additives (<15% v/v). Three types of base oils may be distinguished: 1) traditional bases (obtained by low-volatile fractions from crude oil distillation refining), 2) synthetic bases (mainly poly-alpha-olefins, sometimes esters, especially succinic acid esters), 3) bases of natural origin (especially obtained from refined plant oils). The bases of natural origin...
-
Simultaneous Determination of Indolic Compounds in Plant Extracts by Solid-Phase Extraction and High-Performance Liquid Chromatography with UV and Fluorescence Detection
PublicationA high-performance liquid chromatographic method with UV and fluorescence detection (HPLC-DAD-FLD) was developed for simultaneous determination of indolic compounds in plant material. Indole-3-carbinol (I3C), indole-3-acetic acid (I3AA), indole-3-acetonitrile (I3ACN), and 3,3′-diindolylmethane (DIM) were used as representative compounds that cover a wide spectrum of indole structures occurring in nature. For concentration and purification...
-
Błażej Kudłak dr hab. inż.
People -
Determination of trace levels of eleven bisphenol A analogues in human blood serum by high performance liquid chromatography–tandem mass spectrometry
PublicationChemicals showing structural or functional similarity to bisphenol A (BPA), commonly called BPA analogues, have recently drawn scientific attention due to their common industrial and commercial application as a substitute for BPA. In the European Union, the use of BPA has been severely restricted by law due to its endocrine disrupting properties. Unfortunately, it seems that all BPA analogues show comparable biological activity,...
-
Current trends in analytical strategies for determination of polybrominated diphenyl ethers (PBDEs) in samples with different matrix compositions – Part 1.: Screening of new developments in sample preparation
PublicationPolybrominated diphenyl ethers (PBDEs) are ubiquitous compounds in the environment. Restrictions on the use of PBDEs introduced at the beginning of the 21st century have not eliminated these highly persistent and bioaccumulative compounds from the environment. Despite many existing regulations to control and phase out, extensive research on PBDEs is still necessary to fully evaluate the hazard their create to the environment. In...
-
Dispersive liquid-liquid microextraction combined with gas chromatography–mass spectrometry for in situ determination of biogenic amines in meat: Estimation of meat's freshness
PublicationA dispersive liquid-liquid microextraction (DLLME) gas chromatography–mass spectrometry (GC–MS) technique was developed for the determination of selected biogenic amines (BAs) in samples of poultry, pork and beef. Prior to the extraction process, an appropriate volume of sodium hydroxide solution was added to each of the portioned samples. Next, samples were homogenized, centrifuged and finally sonicated at an increased temperature....
-
Application potential of dummy molecularly imprinted polymers as solidphase extraction sorbents for determination of low-mass polybrominated diphenyl ethers in soil and sediment samples
PublicationDespite the introduction of restrictive regulations in the USA and the European Union, polybrominated diphenyl ethers (PBDEs) are still found in various types of environmental and biological samples at significant concentration levels. The presence of these persistent organic pollutants in the environment raises important issues because of their negative impact on immunological and neurological systems, and on the hormonal balances...
-
The effect of the temperature change rate on determination of the critical pitting temperature of stainless steels
Publication -
Accurate and continuous adhesive fracture energy determination using an instrumented wedge test
PublicationThe wedge test and the related double cantilever beam test are practical methods of assessing structural adhesive fracture energy. In the former, and to a lesser extent the latter, a recognised problem is the difficulty of following the length of the growing crack, required to calculate fracture energy with any accuracy. We present a novel method of measurement of crack length that has the advantages of being accurate and allowing...
-
Neurohypophyseal Receptors-Ligands: Where We Are After the Landmark Rhodopsin Structure Determination
Publication -
Do we need a catalyst in the determination of dissolved organic carbon in environmental samples?
Publication -
Method for determination of the chemical composition of phases of the iron catalyst precursor for ammonia synthesis
Publication -
Structural Investigations and Determination of Current and Voltage Characteristics in Htsc 2G SF12050 Tapes
Publication -
Micellar liquid chromatography for lipophilicity determination of new biologically active 1,3‐purinodiones
Publication -
Determination (monitoring) of PAHs in surface waters: why operationally defined procedure is needed
PublicationW pracy przedstawiono i skomentowano rezultaty badań międzylaboratoryjnych oznaczania wielopierścieniowych węglowodorów aromatycznych w wodzie czystej i wodzie zawierającej zawiesinę. Badania wskazują, ze wyniki oznaczania zależa od zastosowanej techniki izolacji analitów z próbki i końcowej procedury ich rozdzielania i oznaczania. Przeprowadzone badania wskazują, że nowoczesna analityka nie dysponuje technikami izolacji, które...
-
The state of the art in the field of non-stationary instruments for the determination and monitoring of atmospheric pollutants
PublicationW artykule przedstawiono informacje oparte zarówno na danych literaturowych jak i własnych doświadczeniach dotyczące:-podstawowych tendencji rozwojowych w zakresie analityki i monitoringu zaneczyszczeń powietrza atmosferycznego-wymogów metrologicznych stawianych różnych typom urządzeń kontrolno-pomiarowych;-klasyfikacji analizatorów i monitorów wykorzystywanych w monitoringu powietrza.
-
Quantitative determination of titin and nebulin in poultry meat by SDS-PAGE with an internal standard
Publication -
Unmodelled Effects in the Horizontal Velocity Field Determination: ASG-EUPOS Case Study
Publication -
Rapid quantitative determination of butter adulteration with palm oil using the DSC technique
Publication -
Modification of ASM3 for the determination of biomass adsorption/storage capacity in bulking sludge control
PublicationSystemy osadu czynnego z selektorami (SAS) umożliwiają ograniczenie nadmiernego wzrostu bakterii nitkowatych, które odpowiadają za zjawisko zwanę ''puchnięciem osadu''. Celem tych badań było opracowanie modelu matematycznego opisującego szybkie usuwanie substratu w systemach SAS. W tym celu zmodyfikowano Model Osadu Czynnego nr 3 (ASM3) poprzez dodanie równań opisujących zjawiska adsorpcji i bezpośredniego wzrostu bakterii na zaadsorbowanym...
-
Determination of amino acids in urine of patients with prostate cancer and benign prostate growth
Publication -
Determination of Urinary Pterins by Capillary Electrophoresis Coupled with LED-Induced Fluorescence Detector
Publication -
Method for Determination of Methyl tert-Butyl Ether and Its Degradation Products in Water
Publication -
Determination of aliphatic amines in water by gas chromatography using headspace solvent microextraction
Publication -
In-Tube Molecularly Imprinted Polymer Solid-Phase Microextraction for the Selective Determination of Propranolol
Publication -
Determination of the chemical structure of potential organic impurities occurring in drug substance opipramol
PublicationThe tricyclic antipsychotic and antidepressant drug opipramol (opipramole) was examined with regard to the chemical structure of its organic impurities. Impurities were isolated from the technical product by chromatographic methods and their chemical structures were established by 1H NMR, MS and FTIR and further confirmed by comparison with commercially available products or with products obtained by independent synthesis, and...
-
A new scuffing shock test method for the determination of the resistance to scuffing of coated gears
Publication -
The triple-sorbents solid-phase extraction for pharmaceuticals and estrogens determination in wastewater samples
Publication -
Determination of PCBs in river sediment samples—proficiency test for selected Polish laboratories
Publication -
Organomercury Compounds in Environmental Samples: Emission Sources, Toxicity, Environmental Fate, and Determination
Publication -
Determination of Safety Levels of Electronic Devices Exposed to Impact of Strong Electromagnetic Pulses
Publication