Search
Filters
total: 103
Search results for: WORDS: TRUSS, ELASTIC BRACES, IMPERFECTION, STABILIZING LOAD
-
Results of nanoindentation test to calculate residual stress in an eyelet of undercarriage drag strut after laser treatment
Open Research DataIn order to determine the residual stress in the laser-processed an eyelet of undercarriage drag strut, a nanoindentation test was performed before and after stress relief annealing. For this purpose, after the hardness test, the sample was subjected to stress relief annealing at 270 °C for 2 hours. Annealing was performed in a vacuum furnace. Hardness...
-
Ground anchors diagnostic process based on elastic wave propagation method
PublicationThe paper is focused on analysis of elastic wave propagation in the context of diagnostics of ground anchors. Numerical simulations were performed to assess the possibility of evaluation of the anchorage quality. It was assumed that the quality and the load capacity of the anchor system directly depend on the length, on which mortar and steel cooperate.
-
The Influence of Binding Agents on Stiffness of Mineral-cement-emulsion Mixtures
PublicationThis paper attempts to determine the behavior of mineral-cement-emulsion mixture (MCE) under load, whether is it similar to asphalt mixtures (viscoelastic behavior) or to cement treated materials (elastic behavior). To answer this question nine mineral- cement-emulsion mixtures with different combinations of cement and emulsion content were tested in laboratory using Simple Performance Test (SPT). For each mixture stiffness moduli...
-
Acoustic journal bearing – Performance under various load and speed conditions speed conditions
PublicationThe paper presents results of experimental testing aiming at finding out what effect system of piezo-electric actuators (PZTs)attached to an aerodynamic journal bearing has on the magnitude of shaft's motion within the bearing operating at specified speed and load. The results clearly demonstrate effectiveness of PZTs in mitigating the shaft's motion thus contributing to the increased stability of the bearing. This stabilizing...
-
Modelowanie kratownicy z kształtowników giętych na zimno z mimośrodami dodatnimi w węźle = Modelling of truss with cold-formed section and positive eccentricyty in the node.
PublicationThe topic of this research is establishing load-carrying capacity of compressed and tensed chords of trusses made of cold-formed open cross-sections. Occurrence of bending in the truss’ chord is the result of specific production technology assumed by the designer and producer of lattice girder’s systems. The aim of this research is to present methodology of conduct while creating numerical models that best depict the behaviour...
-
Experimental study of the post tensioned prestressed concrete corbels
PublicationThe results of experimental investigation of 6 symmetrical double prestressed corbels of variable shear span to depth ratio and variable location of prestressing bars are presented in the paper. The post ten- sioned corbels were prestressed with Macalloy 1030 bars of 25 mm in diameter. The results of the tests were compared with the cracking and load carrying capacity of corbels reinforced with passive reinforce- ment. As a result...
-
Two- and three-dimensional elastic networks with rigid junctions: modeling within the theory of micropolar shells and solids
PublicationFor two- and three-dimensional elastic structures made of families of flexible elastic fibers undergoing finite deformations, we propose homogenized models within the micropolar elasticity. Here we restrict ourselves to networks with rigid connections between fibers. In other words, we assume that the fibers keep their orthogonality during deformation. Starting from a fiber as the basic structured element modeled by the Cosserat...
-
Fluid structure interaction study of non-Newtonian Casson fluid in a bifurcated channel having stenosis with elastic walls
PublicationFluid–structure interaction (FSI) gained a huge attention of scientists and researchers due to its applications in biomedical and mechanical engineering. One of the most important applications of FSI is to study the elastic wall behavior of stenotic arteries. Blood is the suspension of various cells characterized by shear thinning, yield stress, and viscoelastic qualities that can be assessed by using non-Newtonian models. In this...
-
COMPUTER-AIDED CONSTRUCTION AT DESIGNING REINFORCED CONCRETE COLUMNS AS PER EC
PublicationThe article presents the author’s computer program for designing and dimensioning columns in reinforced concrete structures taking into account phenomena affecting their behaviour and information referring to design as per EC. The computer program was developed with the use of C++ programming language. The program guides the user through particular dimensioning stages: from introducing basic data such as dimensions, concrete...
-
A Diagnostic Method Based on Deflection Analysis for Monitoring Post-elastic Response of Beams
PublicationA non-destructive diagnostic method based on deflection analysis for monitoring the post-elastic response of beams was developed, and a diagnostic indicator was proposed. The indicator was defined as the second moment of the normalised curvature function about the mid-span, where the curvature was computed from the normalised deflection function. Elastic reference values of the indicator were computed for simply supported beams...
-
Experimental Testing of Innovative Cold-Formed "GEB" Section / Badania Eksperymentalne Innowacyjnego Kształtownika Giętego Na Zimno Typu „Geb“
PublicationOne of the major advantages of light gauge steel structures made of cold-formed steel sections is their low weight, so manufacturers are increasingly using the possibilities of those sections for the production of typical single-storey steel structures systems. Well known profiles, such as Z, C and the so called hat sections that have been studied and described in the literature, are used mainly as purlins or truss components....
-
Stability and limit load analysis of a cold-formed channel section column
PublicationThe paper presents stability and limit load analysis of a steel column 1440 mm high of a cold-formed channel section, subjected to a combination of compression and bending. Experimental results were compared to the resistance of a code procedure and to the outcome of numerical non-linear analysis. Comparison was made of numerical solutions by means of static (Riks) and dynamic (Explicit and Implicit) methods. Perfectly elastic...
-
Screw displacement pile shaft deformations measured by vibrating wire and fiber optic systems during a static load test
PublicationThis paper describes a full scale static load test performed on a 400 mm diameter screw displacement pile equipped with four different strain measuring systems. Three types of vibrating wire strain gauges (VWSG) were used: global - retrievable, local attached to steel pipe and local concrete embedded. The fourth system was distributed fiber optic sensors based on Rayleigh back scattering (DFOS) - three in the pile cross section....
-
Speed Observer Structure of Induction Machine Based on Sliding Super-Twisting and Backstepping Techniques
PublicationThis paper presents an analysis of the two speed observer structures which are based on the backstepping and sliding super twisting approach. The observer stabilizing functions result from the Lyapunov theorem. To obtain the observer tuning gains the observer structure is linearized near the equilibrium point. The rotor angular speed is obtained from non-adaptive dependence. In the sensorless control system structure the classical...
-
Elastic distortional buckling of thin-walled bars of closed quadratic cross-section
PublicationIn this study a tin-walled bar with closed quadratic cross-section is considered. The elastic stability of axially compressed bar related to the cross-section distortion is investigated. The governing differential equatio is derived with aid of the principle of stationary potential energy. The critical load for simply supported bar is found in an analytical form and it is copared with the FEM solution. Sufficient accuracy of the...
-
Elastic distortional buckling of thin-walled bars of closed quadratic cross-section
PublicationIn this study a thin-walled bar with closed quadratic cross-section is considered. The elastic stability of axially compressed bar related to the cross-section distortion is investigated. The governing differential equation is derived with aid of the principle of stationary total potential energy. The critical load for the simply supported bar is found in analytical form and it is compared with the FEM solution. Sufficient accuracy...
-
The Point Estimate Method in a Reticulated Shell Reliability Analysis
PublicationThe objective of this paper is to present an application of the point estimate method (PEM) to determine the probabilistic moments for engineering structures. Reliability analysis is illustrated by two examples: an estimation of the critical force in linear elastic buckling analysis and a reticulated shell limit load determinations. Calculations were also made using Monte Carlo method. It has been shown the practical usefulness...
-
Development and experimental validation of a novel double-stage yield steel slit damper-buckling restrained brace
PublicationThis research is focused on the development and experimental validation of a novel double-stage yield steel slit damper-buckling restrained brace (SSD-DYB) system designed for seismic resistance of steel structures. The SSD-DYB integrates the energy dissipation capability of a steel slit damper (SSD) in its initial segment, enhancing performance in the case of lower seismic intensities levels while employing a larger segment for...
-
Buckling resistance of a metal column in a corrugated sheet silo - experiments and non-linear stability calculations
PublicationThe results of experimental and numerical tests of a single corrugated sheet silo column’s buckling resistance are presented in this study. The experiments were performed in a real silo with and without bulk solid (wheat). A very positive impact of the bulk solid on the column buckling resistance occurred. The experimental results were first compared to the buckling resistance calculated by Eurocode 3 formulae. The comparison revealed that...
-
Load Tests of the Movable Footbridge Over the Port Canal in Ustka
PublicationThe paper presents the acceptance tests carried out on the open footbridge over the port canal in the Port of Ustka. The steel footbridge construction is created by a single pylon to which a movable truss span is suspended with a theoretical span of 52.3 m. The studies about load test of the object included static and dynamic extortion and measurements. In static tests the ballast was of pallets with concrete blocks. Dynamic studies...
-
Retrievable strain measuring system in screw displacement piles - readings and results interpretation problems
PublicationStatic load tests on foundation piles are generally carried out in order to determine load – displacement characteristic of the pile. For more detailed information, e.g. force distribution along the shaft, load transfer mechanism and characteristics of soil-structure interaction (unit resistance curves t-z, q-z) additional pile instrumentation is required. Most popular techniques focus on direct concrete strain measurements and...
-
Structural response of existing spatial truss roof construction based on Cosserat rod theory
PublicationPaper presents the application of the Cosserat rod theory and newly developed associated finite elements code as the tools that support in the expert-designing engineering practice. Mechanical principles of the 3D spatially curved rods, dynamics (statics) laws, principle of virtual work are discussed. Corresponding FEM approach with interpolation and accumulation techniques of state variables are shown that enable the formulation...
-
The point estimate method in a reticulated shell reliability analysis
PublicationThe objective of this paper is to present an application of the point estimate method (PEM) that can determine the probabilistic moments for engineering structures. The method is reasonably robust and adequately accurate for a wide range of practical problems. It is a special case of numerical quadrature based on orthogonal polynomials. The main advantage of this method is that, unlike FORM or SORM, it is not necessary to carry...
-
Non-linear static stability of bi-layer carbon nanosheets resting on an elastic matrix under various types of in-plane shearing loads in thermo-elasticity using nonlocal continuum
PublicationIn this research, the shear and thermal buckling of bi-layer rectangular orthotropic carbon nanosheets embedded on an elastic matrix using the nonlocal elasticity theory and non-linear strains of Von-Karman was studied. The bi-layer carbon sheets were modeled as a double-layered plate, and van der Waals forces between layers were considered. The governing equations and boundary conditions were obtained using the first order shear...
-
Water-Lubricated Sintered Bronze Journal Bearings—Theoretical and Experimental Research
PublicationWater lubricated bearings are used from many years in shipbuilding, hydro power and other industries because of their advantages such as: extensive serviceable life, low coefficient of friction, longevity of shaft sleeve, good abrasion resistance, low maintenance required, unit simplicity, no danger of pollution and low price. Various types of water lubricated sliding bearings have been tested at the Technical University of Gdansk...
-
The reasons of considarable deflections of roof trusses in engineering analysis
PublicationThe aim of the paper is to present an unconventional analysis of deformations of roof trusses of an exhibition pavilion. Structure of the main hall of the pavilion consists of repeatable span frames with steel pillars made of I-sections, fastened in the foundations and hinged supporting roof girders. The roof trusses, completed in steel construction, have undergone considerable permanent deflections. Deformations of the lower chord...
-
An in situ technique for the assessment of adhesive properties of a joint under load
PublicationSlow crack propagation in adhesive bonded joints has been characterised using an asymmetric wedge test. Crack position was evaluated from strain gauge measurements, both in the debonded partof the joint and in the bonded zone. Test temperature was changed during loading, giving insight into bond evolution. The technique allows accurate, and virtually continuous, determination of crack position to be made, and therefore the evaluation...
-
Large thermo-elastic displacement and stability FEM analysis of multilayered plates and shells
PublicationThe paper concerns the load capacity analysis of thermally loaded multilayered plates and shells. The multilayered body is treated as an equivalent single layer whose kinematics is consistent with first order shear deformation theory. The authors focus on the thermo-elastic stability problem of the thin-walled structures. The equilibrium paths are traced with the use of Riks-Wempner-Ramm algorithm. By making use of the Tsai-Wu...
-
Dynamic analysis of the impact of the wind spectrum according to the theory of Davenport for lightweight structures of the roof in sports hall Czyzyna in Cracow.
PublicationThe main aim of this analysis is to characterize numerical simulations connected with modeling dynamic influence of wind on the lightweight structures of the roof in sports hall – “Czyżyna”. This hall is built in Cracow. The article also involves the proposals of the solutions connected with dynamic influence of the wind – Davenport’s method has been used. These proposals have not been taken into consideration at the detailed engineering...
-
Damage detection in a bolted lap joint using guided waves
PublicationThe paper presents the experimental investigation of guided waves application to the condition assessment of prestressed bolted connections and a concept of new quantitative indicator. The main goal of the research was the analysis of the influence of the contact conditions changes to the characteristics of a propagating disturbance. The experimental tests were carried out for a single bolted lap joint. The excitation and acquisition...
-
SIMULATION OF PROCEED® SURGICAL MESH APPLIED TO VENTRAL HERNIA REPAIR
PublicationIn the present research, Proceed® implant is considered. The system is subjected to short-time dynamic pressure load, similar to post-operative cough naturally occurring in human abdomen. The model refers to a clinical case of 5cm of hernia operated by Proceed implant fixed by 15 joints every 3cm around the orifice. The simulations of the implanted mesh are performed by means of the Finite Element Method. The implant is modelled...
-
Fracture Energy of Bonded Joints with 2D Elastic Adhesive Layer
PublicationWhen bonded joint is subjected to mode I fracture loading, the adhesive joints analytical solutions treats the adhesive layer, usually, as not existing or 1D Hooke elastic layer. In the case of 1D elastic layer, represented as Hookes spring element, is acting, only, in direction contrary to the applied load. Basing on the information yielded from sensitive laser profilometry technique, where deflections of bonded part of the joint...
-
Modern GFRP Composite Footbridges
PublicationApplication of GFRP composites in civil engineering is still not large but already noticeable. Advantages of this material, such as: low volume weight, relatively high stiffness and strength, well fatigue resistance, easiness in shaping, high material damping and high environmental resistance, make it attractive for bridge and in particular foot-bridge designers. It is estimated that nowadays in the world there are realized hundreds...
-
The effective elastic properties of human trabecular bone may be approximated using micro-finite element analyses of embedded volume elements.
PublicationBoundary conditions (BCs) and sample size affect the measured elastic properties of cancellous bone. Samples too small to be representative appear stiffer under kinematic uniform BCs (KUBCs) than under periodicity-compatible mixed uniform BCs (PMUBCs). To avoid those effects, we propose to determine the effective properties of trabecular bone using an embedded configuration. Cubic samples of various sizes (2.63, 5.29, 7.96, 10.58...
-
Improving performance of large thrust bearings through modeling and experimentation
PublicationLarge thrust bearings are highly loaded machine elements and their failures cause serious losses. Start ups and stoppages of the bearing under load are specially critical regimes of operation. Load carrying capacity depends on the profile of the oil gap. In transient states this profile is also changing. In the design of large thrust bearings minimizing thermo-elastic deformations is an important goal, which can be accomplished...
-
Uproszczone metody obliczania wyboczenia silosów z blachy falistej wzmocnionych słupami na podstawie analizy MES i wyników doświadczalnych
PublicationRozprawa doktorska dotyczy zagadnienia stateczności i nośności granicznej stalowych silosów z płaszczem z blachy falistej wzmocnionych pionowymi słupami. Przeprowadzono zaawansowane analizy numeryczne MES oraz badania doświadczalne dotyczące wyboczenia/stateczności analizowanych silosów. Analizy numeryczne zostały przeprowadzone w zakresie liniowej oraz nieliniowej analizy stateczności, z uwzględnieniem wstępnych imperfekcji geometrycznych...
-
Problems of analytical determination of journal bearing bush fatigue strength estimates
PublicationProblems connected with determination of stress distribution in sliding layer of thinwalled bearing bushes, investigated in bearing fatigue test rigs, have been presented. Using an example of plain bearings tested in the fatigue machine SMOK (built at the Gdask University of Technology) problems with obtaining a convergence of iterative procedure for determining the fatigue strength estimators of bearing alloy surface layer are...
-
The Effect of Flexible Pavement Mechanics on the Accuracy of Axle Load Sensors in Vehicle Weigh-in-Motion Systems
PublicationWeigh-in-Motion systems are tools to prevent road pavements from the adverse phenomena of vehicle overloading. However, the effectiveness of these systems can be significantly increased by improving weighing accuracy, which is now insufficient for direct enforcement of overloaded vehicles. Field tests show that the accuracy of Weigh-in-Motion axle load sensors installed in the flexible (asphalt) pavements depends on pavement temperature...
-
Effect of Axial Porosities on Flexomagnetic Response of In-Plane Compressed Piezomagnetic Nanobeams
PublicationWe investigated the stability of an axially loaded Euler–Bernoulli porous nanobeam considering the flexomagnetic material properties. The flexomagneticity relates to the magnetization with strain gradients. Here we assume both piezomagnetic and flexomagnetic phenomena are coupled simultaneously with elastic relations in an inverse magnetization. Similar to flexoelectricity, the flexomagneticity is a size-dependent property. Therefore,...
-
Chained machine learning model for predicting load capacity and ductility of steel fiber–reinforced concrete beams
PublicationOne of the main issues associated with steel fiber–reinforced concrete (SFRC) beams is the ability to anticipate their flexural response. With a comprehensive grid search, several stacked models (i.e., chained, parallel) consisting of various machine learning (ML) algorithms and artificial neural networks (ANNs) were developed to predict the flexural response of SFRC beams. The flexural performance of SFRC beams under bending was...
-
Numerical analysis of mechanical properties of an infill structure used in 3D printings
PublicationThe paper presents results of a numerical analysis focused on an identification of mechanical properties of an element created by using Fused Deposition Modelling additive manufacturing technique (FDM). There is presented a description of technology of the 3D printing, numerical model created by using the finite element method (FEM), as well as some problems referred to estimation of the mechanical properties of the printout. The...
-
Laser Beam as a Precision Tool to Increase Fatigue Resistance in an Eyelet of Undercarriage Drag Strut
PublicationThe article contains the results of tests on a laser-processed eyelet of undercarriage drag strut to increase its fatigue strength. Laser processing concentrated on both sides around the hole of eye for connecting the undercarriage drag strut caused that the material in this area withstood more than twice the number of load cycles established for this material. In order to determine the reasons for the increase in fatigue strength,...
-
Structural Design and Sensitivity Analysis of Semi-Rigid Pavement of a Motorway
PublicationThis paper presents application of mechanistic-empirical methods in design of semi-rigid pavement for a section of a motorway in Poland. The stage construction was assumed. Three fatigue criteria were applied in the design. For asphalt fatigue cracking and subgrade soil the criteria from the Asphalt Institute (1981) were applied. For fatigue cracking of cement stabilized bases the Dempsey (1984) and De Beer (1992) criteria were...
-
NUMERICAL MODEL OF PLASTIC DESTRUCTION OF THICK STEEL STRUCTURAL ELEMENTS
PublicationIn the shipbuilding industry, the risk of brittle fracture of the structure is limited by using certified materials with specified impact strength, determined by the Charpy method (for a given design temperature) and by supervising the welding processes (technology qualification, production supervision, non-destructive testing). For off-shore constructions, classical shipbuilding requirements may not be sufficient. Therefore, the...
-
Stability analysis of single-walled carbon nanotubes embedded in winkler foundation placed in a thermal environment considering the surface effect using a new refined beam theory
PublicationThis article is devoted to investigate the stability of different types of Single Walled Carbon Nanotubes (SWCNTs) such as zigzag, chiral, and armchair types which are rested in Winkler elastic foundations exposing to both the low and high temperature environments. Also, the Surface effects which include surface energy and surface residual stresses, are taken into consideration in this study. It may be noted that the surface energy...
-
Implementation of failover and load balancing algorithms in SIP PBX High Availability system
PublicationGoal of the project was to design a High Availability SIP VoIP system that guarantees access to additional services like auto-attendent and automatic call distribution. The realization of the project required system to have load balancing and failover algorithms implemented. From the end users’ point of view the whole system had to figure as a single element. After taking under consideration the known methods of implementations...
-
Influence of the notch rounding radius on estimating the elastic notch stress concentration factor in a laser welded tee joint
PublicationIn recent years an increased interest of industry in sandwich-type metal structures can be observed. These structures consist of thin plates of 2.5 mm in thickness separated by stiffeners of different shapes and forms. Welds joining the plates and stiffeners are made on the outer side of the plates using laser welding technique. A locally focused source of heat causes the plate to melt creating a very narrow and elongated joint....
-
Selected local stability problems of channel section flanges made of aluminium alloys
PublicationThe paper addresses the issue of local buckling of compressed flanges of cold-formed thin-walled channel columns and beams with nonstandard flanges composed of aluminium alloys. The material behaviour follows the Ramberg–Osgood law. It should be noted that the proposed solution may be also applied for other materials, for example: stainless steel, carbon steel. The paper is motivated by an increasing interest in nonstandard cold-formed...
-
Physical and mathematical modelling of implant-fascia system in order to improve laparoscopic repair of ventral hernia
PublicationThis paper describes an investigation of biomechanical behaviour of hernia repair, which is focused on the selection of safe linking of certain type of implant with fascia in laparoscopic operation. The strength of various fixations of the implant to the fascia is analysed. Methods: The research is based on experimental observations of operated hernia model behaviour during a dynamic impulse load corresponding to post-operative...
-
Anisotropy and compaction gradient assessment on rammed earth specimens through sonic tomography approach
PublicationRammed earth is a traditional construction technique that has recently gained attention because of its benefits from an ecological perspective. The conservation of the existing valuable cultural heritage sites and the quality control of new constructions built with this material require the development and application of practical inspection techniques. This paper explores the application of sonic tests and sonic tomography as...