Search results for: DENSITY CORRECTION
-
Prediction of flow boiling heat transfer data for R134a, R600a and R290 in minichannels
PublicationIn the paper presented is the analysis of the results of calculations using a model to predict flow boiling of refrigerants such as R134a, R600a and R290. The latter two fluids were not used in development of model semiempirical correction. For that reason the model was verified with present experimental data. The experimental research was conducted for a full range of quality variation and a relatively wide range of mass velocity....
-
Fixed Pattern Noise Reduction and Linearity Improvement in Time-Mode CMOS Image Sensors
PublicationIn the paper, a digital clock stopping technique for gain and offset correction in time-mode analog-to-digital converters (ADCs) has been proposed. The technique is dedicated to imagers with massively parallel image acquisition working in the time mode where compensation of dark signal non-uniformity (DSNU) as well as photo-response non-uniformity (PRNU) is critical. Fixed pattern noise (FPN) reduction has been experimentally validated...
-
AUDIO SIGNAL EQUALIZATION BASED ON IMPULSE RESPONSE OF A LISTENING ROOM AND MUSIC CONTENT REPRODUCED
PublicationA research study presents investigations of the influence of the room acoustics on the frequency characteristic of the audio signal playback. First, a concept of a novel spectral equalization method of the room acoustic conditions is introduced. On the basis of the room spectral response, a system for room acoustics compensation based on an equalizer designed is proposed. The system settings depend on music genre recognized automatically....
-
Mobile indicators in GIS and GPS positioning accuracy in cities
PublicationThe publication describes the possible use of tele-geoprocessing as a synergy of modern IT solutions, telecommunications and GIS algorithms. The paper presents a possibility of urban traffic monitoring with the use of mobile GIS indicators of dedicated monitoring system designed for taxi corporation. The system is based on a stationary and mobile software package. The optimal and minimal assumptions for the monitoring of urban...
-
Measurement method for capacitive sensors for microcontrollers based on a phase shifter
PublicationA complete measurement method dedicated to capacitive sensors has been developed. It includes the development of hardware (an analogue interface circuit for microcontrollers with built-in times/counters and analogue comparators) and software (a measurement procedure and a systematic error calibration (correction) algorithm which is based on a calibration dictionary). The interface circuit consists of a low-pass filter and a phase...
-
Automatic Correction of Non-Anechoic Antenna Measurements using Low-Pass Filters
PublicationPrototype measurements belong to key steps in the development of antenna structures. They are normally performed in expensive facilities, such as anechoic chambers (ACs). Alternatively, antenna performance can be extracted (at a low cost) in non-anechoic conditions upon appropriate post-processing. Unfortunately, existing correction algorithms are difficult to set up and prone to failure, which limits their practical usefulness....
-
Analysis of the influence of external conditions on temperature readings in thermograms and adaptive adjustment of the measured temperature value
PublicationMeasuring human temperature is a crucial step in preventing the spread of diseases such as COVID-19. For the proper operation of an automatic body temperature measurement system throughout the year, it is necessary to consider outdoor conditions. In this paper, the effect of atmospheric factors on facial temperature readings using infrared thermography is investigated. A thorough analysis of the variation of facial temperature...
-
An approach to constructing genuinely entangled subspaces of maximal dimension
PublicationGenuinely entangled subspaces (GESs) are the class of completely entangled subspaces that contain only genuinely multiparty entangled states. They constitute a particularly useful notion in the theory of entanglement but also have found an application, for instance, in quantum error correction and cryptography. In a recent study (Demianowicz and Augusiak in Phys Rev A 98:012313, 2018), we have shown how GESs can be efficiently...
-
Size Reduction of Microwave Couplers by EM-Driven Optimization
PublicationThis work addresses simulation-driven design optimization of compact microwave couplers that explicitly aims at circuit footprint area reduction. The penalty function approach allows us to minimize the area of the circuit while ensuring a proper power division between the output ports and providing a sufficient bandwidth with respect to return loss and isolation around the operating frequency. Computational cost of the optimization...
-
Equivalent single-layer models in deformation analysis of laminated multilayered plates
PublicationThe performance of selected Equivalent Single-Layer (ESL) models is evaluated within several classical benchmark tests for linear static analysis of multi-layered plates. The authors elaborated their own Finite Element software based on the first-order shear deformation theory (FOSD) with some modifications incorporated including a correction of the transverse shear stiffness and an application of zig-zag type functions. Seven...
-
On the Buckling Response of Axially Pressurized Nanotubes Based on a Novel Nonlocal Beam Theory
PublicationIn the present study, the buckling analysis of single-walled carbon nanotubes (SWCNT) on the basis of a new refined beam theory is analyzed. The SWCNT is modeled as an elastic beam subjected to unidirectional compressive loads. To achieve this aim, the new proposed beam theory has only one unknown variable which leads to one equation similar to Euler beam theory and is also free from any shear correction factors. The equilibrium...
-
Analytical Buckling of FG Nanobeams on The Basis of A New One Variable First-Order Shear Deformation Beam Theory
PublicationIn this work, buckling analysis of functionally graded (FG) nanobeams based on a new refined beam theory has been analyzed. The beam is modeled as an elastic beam subjected to unidirectional compressive loads. To achieve this aim, the new obtained beam theory has only one variable which leads to one equation similar to the Euler beam theory and also is free of any shear correction factor. The equilibrium equation has been...
-
Expedited design of microstrip antenna subarrays using surrogate-based optimization
PublicationComputationally efficient simulation-driven design of microstrip antenna subarrays is presented. The proposed design approach aims at simultaneous adjustment of all relevant geometry parameters of the subarray, which allows us to take into account the effect of the feeding network on the subarray radiation pattern (in particular, the side lobe level, SLL). In order to handle a large number of variables involved in the design process,...
-
Aerodynamic shape optimization by variable-fidelity computational fluid dynamics models: a review of recent progress
PublicationA brief review of some recent variable-fidelity aerodynamic shape optimization methods is presented.We discuss three techniques that—by exploiting information embedded in low-fidelity computationalfluid dynamics (CFD) models—are able to yield a satisfactory design at a low computational cost, usu-ally corresponding to a few evaluations of the original, high-fidelity CFD model to be optimized. Thespecific techniques considered here...
-
The idea of a robotic single-sided lapping system
PublicationThis paper reviews the idea of a robotic lapping system. Robot’s assistance automates the lap-ping process and supports the development of a flexible lapping system. However, the main aim behind the idea of a robotic lapping system is to provide improved means for controlling the posi-tion of conditioning rings on a lapping plate. Due to the kinematics of lapping process, the profile wear of the tool is not constant along the radius....
-
Fast Multi-Objective Optimization of Narrow-Band Antennas Using RSA Models and Design Space Reduction
PublicationComputationally efficient technique for multi-objective design optimization of narrow-band antennas is presented. In our approach, the corrected low-fidelity antenna model (obtained through coarse-discretization EM simulations) is enhanced using frequency scaling and response correction, sampled, and utilized to obtain a fast response surface approximation (RSA) antenna surrogate. The RSA model is constructed in the reduced design space....
-
Accurate Post-processing of Spatially-Separated Antenna Measurements Realized in Non-Anechoic Environments
PublicationAntenna far-field performance is normally evaluated in expensive laboratories that maintain strict control over the propagation environment. Alternatively, the responses can be measured in non-anechoic conditions and then refined to extract the information on the structure field-related behavior. Here, a framework for correction of antenna measurements performed in non-anechoic test site has been proposed. The method involves automatic...
-
Non-invasive blood glucose monitoring with Raman spectroscopy: prospects for device miniaturization
PublicationThe number of patients with diabetes has reached over 350 million, and still continues to increase. The need for regular blood glucose monitoring sparks the interest in the development of modern detection technologies. One of those methods, which allows for noninvasive measurements, is Raman spectroscopy. The ability of infrared light to penetrate deep into tissues allows for obtaining measurements through the skin without its...
-
The applicability of low-cost PM10 sensors for atmospheric air quality monitoring
PublicationDescribed in this work are the results of field tests carried out in the Tricity Agglomeration between 01 April 2018 and 30 June 2018 in order to evaluate the usefulness of low-cost PM10 sensors in atmospheric air quality monitoring. The results were juxtaposed with the results obtained using reference methods. The results were validated based on the measurement uncertainty as described in...
-
Reduced-cost constrained miniaturization of wideband antennas using improved trust-region gradient search with repair step
PublicationIn the letter, an improved algorithm for electromagnetic (EM)-driven size reduction of wideband antennas is proposed. Our methodology utilizes variable-fidelity EM simulation models, auxiliary polynomial regression surrogates, as well as multi-point response correction. The constraint handling is implicit, using penalty functions. The core optimization algorithm is a trust-region gradient search with a repair step added in order...
-
Three-objective antenna optimization by means of kriging surrogates and domain segmentation
PublicationIn this paper, an optimization framework for multi-objective design of antenna structures is discussed which exploits data-driven surrogates, a multi-objective evolutionary algorithm, response correction techniques for design refinement, as well as generalized domain segmentation. The last mechanism is introduced to constrain the design space region subjected to sampling, which permits reduction of the number of training data samples...
-
Prospects in elongation of railway transition curves
PublicationThe paper presents an analysis of the elongation of transition curves in relation to railway track alignment correction and modernisation. The analysis is based on numerical computations for a wide range of parameters describing a typical railway geometrical layout with transition curves. The differences between the horizontal ordinates of the existing layout and the layout with the elongated transition curves are evaluated and...
-
Pareto Ranking Bisection Algorithm for Expedited Multi-Objective Optimization of Antenna Structures
PublicationThe purpose of this letter is introduction of a novel methodology for expedited multi-objective design of antenna structures. The key component of the presented approach is fast identification of the initial representation of the Pareto front (i.e., a set of design representing the best possible trade-offs between conflicting objectives) using a Pareto-ranking bisection algorithm. The algorithm finds a discrete set of Pareto-optimal...
-
Cost-efficient simulation-driven design of compact impedance matching transformers
PublicationIn this paper, an algorithmic framework for cost-efficient design optimization of miniaturized impedance matching transformers has been presented. Our approach exploits a bottom-up design that involves translating the overall design specifications for the circuit at hand to its elementary building blocks (here, compact microstrip resonant cells, CMRCs), as well as fast surrogate-assisted optimization of the cells followed by simulation-based...
-
Parameters of land reference points in the Gdynia region and the Free-air anomaly grid of the South Baltic
Open Research DataThe data was registered during the campaign to verify the catalog value of the absolute point coordinates [point 5403 (POLREF-GORA DONAS)] of the national gravimetric control network. The data was recorded in two three-hour stationary measurement campaigns at the following points: Rozewie of the EUREF-POL network, Góra Donas POLREF, and mareograph points...
-
Low-cost EM-Simulation-based Multi-objective Design Optimization of Miniaturized Microwave Structures
PublicationIn this work, a simple yet reliable technique for fast multi-objective design optimization of miniaturized microwave structures is discussed. The proposed methodology is based on point-by-point identification of a Pareto-optimal set of designs representing the best possible trade-offs between conflicting objectives such as electrical performance parameters as well as the size of the structure of interest. For the sake of computational...
-
Bending and buckling formulation of graphene sheets based on nonlocal simple first-order shear deformation theory
PublicationThis paper presents a formulation based on simple first-order shear deformation theory (S-FSDT) for large deflection and buckling of orthotropic single-layered graphene sheets (SLGSs). The S-FSDT has many advantages compared to the classical plate theory (CPT) and conventional FSDT such as needless of shear correction factor, containing less number of unknowns than the existing FSDT and strong similarities with the CPT. Governing...
-
Methodology for the Correction of the Spatial Orientation Angles of the Unmanned Aerial Vehicle Using Real Time GNSS, a Shoreline Image and an Electronic Navigational Chart
PublicationUndoubtedly, Low-Altitude Unmanned Aerial Vehicles (UAVs) are becoming more common in marine applications. Equipped with a Global Navigation Satellite System (GNSS) Real-Time Kinematic (RTK) receiver for highly accurate positioning, they perform camera and Light Detection and Ranging (LiDAR) measurements. Unfortunately, these measurements may still be subject to large errors-mainly due to the inaccuracy of measurement of the optical...
-
Analysis of a caustic formed by a spherical reflector: Impact of a caustic on architectural acoustics
PublicationFocusing sound in rooms intended for listening to music or speech is an acoustic defect. Design recommendations provide remedial steps to effectively prevent this. However, there is a category of objects of high historical or architectural value in which the sound focus correction is limited or even abandoned. This also applies to indoor or outdoor concert shells, installations for teaching and acoustic presentations, etc. The...
-
A structure and simulation-driven design of compact CPW-fed UWB antenna
PublicationIn this letter, a structure of a miniaturized ultra-wideband CPW-fed antenna and its design proce-dure are presented. The antenna is a modified version of the design previously proposed in the literature, with additional degrees of freedom introduced in order to improve the structure flexibility. The small size is achieved by executing a rigorous optimization procedure that consists of two stages: (i) smart random search carried...
-
Fast surrogate-assisted simulation-driven design of compact microwave hybrid couplers
PublicationThis work presents a robust methodology for expedited simulation-driven design optimization of compact microwave hybrid couplers. The technique relies on problem decomposition, and a bot-tom–up design strategy, starting from the level of basic building blocks of the coupler, and finishing with a tuning procedure that exploits a fast surrogate model of the entire structure. The latter is constructed by cascading local response surface...
-
Expedited Design Closure of Antennas By Means Of Trust-Region-Based Adaptive Response Scaling
PublicationIn the letter, a reliable procedure for expedited design optimization of antenna structures by means of trust-region adaptive response scaling (TR-ARS) is proposed. The presented approach exploits two-level electromagnetic (EM) simulation models. A predicted high-fidelity model response is obtained by applying nonlinear frequency and amplitude correction to the low-fidelity model. The surrogate created this way is iteratively rebuilt...
-
Comprehensive dimension scaling of multi-band antennas for operating frequencies and substrate parameters
PublicationIn this paper, low-cost and comprehensive redesign of multi-band antennas with respect to the operating frequencies and material parameters of the substrate is presented. Our approach exploits an inverse surrogate model identified based on a set of reference designs optimized at the level of coarse-discretization EM simulations of the antenna at hand. An iterative correction procedure is also implemented to account for the initial...
-
Rapid multi-objective design optimisation of compact microwave couplers by means of physics-based surrogates
PublicationThe authors introduce a methodology for fast multi-objective design optimisation of miniaturised microwave couplers. The approach exploits the surrogate-based optimisation paradigm with an underlying low-fidelity model constructed from an equivalent circuit of the structure under consideration, corrected through implicit and frequency space mapping. A fast prediction tool obtained this way is subsequently optimised by a multi-objective...
-
WPŁYW TRANSFORMACJI DANYCH NA JAKOŚĆ OPRACOWANYCH METOD TOŻSAMOŚCIOWYCH W SPEKTROSKOPII BLISKIEJ PODCZERWIENI
PublicationSpektroskopia bliskiej podczerwieni (NIR) wykorzystuje absorpcję promieniowania elektromagnetycznego w zakresie 12000-4000 cm-1, (780¬-2500 nm). Absorpcja NIR pochodzi od nadtonów i drgań kombinacyjnych wiązań C-H, N-H, O-H. Widmo uzyskane techniką NIR jest unikatowym "odciskiem palca" badanej substancji gdyż zależy zarówno od właściwości fizyko-chemicznych próbki jak i od stanu fazowego oraz postaci krystalicznej jej składników.Zaletami...
-
Digital Filtering of Railway Track Coordinates in Mobile Multi–Receiver GNSS Measurements
PublicationThe article discusses an important issue in connection with the technique of mobile Global Navigation Satellite System (GNSS) measurements of railway track coordinates, which is digital filtering performed to precisely determine railway track axes. For this purpose, a measuring technique is proposed which bases on the use of a measuring platform with a number of appropriately distributed GNSS receivers, where two of them determine...
-
Low-Cost EM-Simulation-Driven Multi-Objective Optimization of Antennas
PublicationA surrogate-based method for efficient multi-objective antenna optimization is presented. Our technique exploits response surface approximation (RSA) model constructed from sampled low-fidelity antenna model (here, obtained through coarse-discretization EM simulation). The RSA model enables fast determination of the best available trade-offs between conflicting design goals. A low-cost RSA model construction is possible through...
-
An extended basis inexact shift–invert Lanczos for the efficient solution of large-scale generalized eigenproblems
PublicationThis paper proposes a technique, based on the Inexact Shift–Invert Lanczos (ISIL) method with Inexact Jacobi Orthogonal Component Correction (IJOCC) refinement, and a preconditioned conjugate-gradient (PCG) linear solver with multilevel preconditioner, for finding several eigenvalues for generalized symmetric eigenproblems. Several eigenvalues are found by constructing (with the ISIL process) an extended projection basis. Presented...
-
Numerical Study on Seismic Response of a High-Rise RC Irregular Residential Building Considering Soil-Structure Interaction
PublicationThe objective of the present study is to investigate the importance of soilstructure interaction effects on the seismic response of a high-rise irregular reinforced-concrete residential building. In order to conduct this research, a detailed three-dimensional structure model was subjected to various earthquake excitations, also including a strong mining tremor. Soil-foundation flexibility was represented using the spring-based...
-
Inverse and forward surrogate models for expedited design optimization of unequal-power-split patch couplers
PublicationIn the paper, a procedure for precise and expedited design optimization of unequal power split patchcouplers is proposed. Our methodology aims at identifying the coupler dimensions that correspond to thecircuit operating at the requested frequency and featuring a required power split. At the same time, thedesign process is supposed to be computationally efficient. The proposed methodology involves two typesof auxiliary models (surrogates):...
-
Model Correction and Optimization Framework for Expedited EM-Driven Surrogate-Assisted Design of Compact Antennas
PublicationDesign of compact antennas is a numerically challenging process that heavily relies on electromagnetic (EM) simulations and numerical optimization algorithms. For reliability of simulation results, EM models of small radiators often include connectors which—despite being components with fixed dimensions—significantly contribute to evaluation cost. In this letter, a response correction method for antenna models without connector,...
-
Multi-objective design optimization of antennas for reflection, size, and gain variability using kriging surrogates and generalized domain segmentation
PublicationCost-efficient multi-objective design optimization of antennas is presented. The framework exploits auxiliary data-driven surrogates, a multi-objective evolutionary algorithm for initial Pareto front identification, response correction techniques for design refinement, as well as generalized domain segmentation. The purpose of this last mechanism is to reduce the volume of the design space region that needs to be sampled in order...
-
Low-cost multi-objective design of compact microwave structures using domain patching
PublicationA good compromise between size and electrical performance is an important design consideration for compact microwave structures. Comprehensive information about size/performance trade-offs can be obtained through multi-objective optimization. Due to considerable electromagnetic (EM) cross-couplings in highly compressed layouts, the design process has to be conducted at the level of high-fidelity EM analysis which is computationally...
-
Fast geometry scaling of UWB band-notch antennas
PublicationImplementation of band-notch capability plays an important role in the design of ultra-wideband (UWB) antennas. At the same time, appropriate sizing of antenna geometry parameters in order to precisely allocate the notch at the required frequency as well as to ensure sufficient reflection level is quite challenging and has to be based—for reliability reasons—on full-wave electromagnetic (EM) simulations of the structure. In this...
-
Analytical Buckling of FG Nanobeams on The Basis of A New One Variable First-Order Shear Deformation Beam Theory
PublicationIn this work, buckling analysis of functionally graded (FG) nanobeams based on a new refined beam theory has been analyzed. The beam is modeled as an elastic beam subjected to unidirectional compressive loads. To achieve this aim, the new obtained beam theory has only one variable which lead to one equation similar to Euler beam theory and also is free of any shear correction factor. The...
-
Stabilność odpowiedzi półprzewodnikowych czujników gazu w zmiennych warunkach środowiskowych – badania długoterminowe oraz korekcja dryftu
PublicationJednym z mankamentów związanych z użytkowaniem półprzewodnikowych czujników gazu jest brak ich stabilności długoterminowej związanej, między innymi, z wpływem czynników środowiskowych takich jak temperatura bądź wilgotność. Badania nad wpływem tych czynników na stabilność odpowiedzi czujników są niezbędne, gdyż poznanie mechanizmu ich oddziaływania jest kluczowe dla opracowania skutecznych algorytmów kompensacyjnych umożliwiających...
-
Multitaper-Based Post-processing of Compact Antenna Responses Obtained in Non-anechoic Conditions
PublicationThe process of developing antenna structures typically involves prototype measurements. While accurate validation of far-field performance can be performed in dedicated facilities like anechoic chambers, high cost of construction and maintenance might not justify their use for teaching, or low-budget research scenarios. Non-anechoic experiments provide a cost-effective alternative, however the performance metrics obtained in such...
-
A facile method for Tauc exponent and corresponding electronic transitions determination in semiconductors directly from UV–Vis spectroscopy data
PublicationIn this work, a facile method allowing for estimation of the exponent in the Tauc equation directly from the UV–vis spectra is presented. It is based on the Taylor expansion of the logarithmic version of the Tauc equation. The Tauc exponent is calculated from the tangent slope of the absorption data. Knowledge of this coefficient provides information about the optical transition types and is used as an input for the calculations...
-
Reliable OFDM Data Transmission with Pilot Tones and Error-Correction Coding in Shallow Underwater Acoustic Channel
PublicationThe performance of Underwater Acoustic Communication (UAC) systems are strongly related to the specific propagation conditions of the underwater channel. Horizontal, shallow-water channels are characterised by extremely disadvantageous transmission properties, due to strong multipath propagation and refraction phenomena. The paper presents the results of communication tests performed during a shallow, inland-water experiment with...
-
Fast surrogate-assisted frequency scaling of planar antennas with circular polarisation
PublicationIn this work, the problem of computationally efficient frequency scaling (re-design) of circular polarisation antennas is addressed using surrogate-assisted techniques. The task is challenging and requires the identification of the optimum geometry parameters to enable the operation of the re-designed structure at a selected (required) centre frequency. This involves handling several performance figures such as the antenna gain,...