displaying 1000 best results Help
Search results for: NON-DESTRUCTIVE TESTING GUIDED WAVE PROPAGATION DEBONDING REINFORCED CONCRETE ADHESIVE CONNECTION FLEXURAL WAVE
-
Modes of Failure Analysis in Reinforced Concrete Beam Using Laser Scanning and Synchro-Photogrammetry
PublicationThe following paper reveal the limitations and possibilities of terrestrial laser scanning technology adaptation in diagnostics of reinforced concrete beams. In this paper, authors present potential spectrum of TLS use in modes of failure analysis of R-C beams and determines under which conditions the laser technologies might be applied. Research was carried out at the Regional Laboratory of Structural Engineering at Gdansk University...
-
Influence of stirrups in a concrete shell on strengthening reinforced concrete column
PublicationTwelve concrete columns, with a 150x150mm square section and three columns with a circular section (d=200mm), are tested to investigate the effect of strengthening by RC jacket. Based on a confined concrete model for axial static loading, an analytical methods, reported in the literature are proposed to predict the behavior of columns with RC jacket. The results support the conception that the effect of strengthening depends...
-
Importance of sign conventions on analytical solutions to the wave-induced cyclic response of a poro-elastic seabed
PublicationThis paper discusses the influence of different sign conventions for strains and stresses, i.e. the solid mechanics sign convention and the soil mechanics sign convention, on the form of governing partial differential equations (the static equilibrium equations and the continuity equation) used to describe the wave-induced cyclic response of a poro-elastic seabed due to propagation of a sinusoidal surface water-wave. Some selected...
-
Structural Assessment of Reinforced Concrete Beams Incorporating Waste Plastic Straws
PublicationThe behavior of reinforced concrete beams containing fibers made of waste plastic straws (WPSs) under the three point bending test is examined. The effect of WPS fiber addition on the compressive and split tensile strength is reported. Four concrete mixes were prepared. The control mix PS-0 had a proportion of 1 cement: 1 sand: 2 coarse aggregate and a water cement ratio of 0.4. In the other three mixes PS-0.5, PS-1.5 and PS-3,...
-
Chained machine learning model for predicting load capacity and ductility of steel fiber–reinforced concrete beams
PublicationOne of the main issues associated with steel fiber–reinforced concrete (SFRC) beams is the ability to anticipate their flexural response. With a comprehensive grid search, several stacked models (i.e., chained, parallel) consisting of various machine learning (ML) algorithms and artificial neural networks (ANNs) were developed to predict the flexural response of SFRC beams. The flexural performance of SFRC beams under bending was...
-
Non-destructive adhesion control.
PublicationW przeciwieństwie do innych metod, spektroskopia impedancyjna jest zdolna do wyznaczania adhezji międzywarstwowej np. systemu powłokowego stosowanego do ochrony samochodów basecoat/clercoat ''in situ'' i niedestrukcyjnie. Obniżenie adhezji międzywarstwowej przebiega analogicznie jak zmiany energi aktywacji przewodnictwa jonowego w obszarze międzywarstwowym, co jest mierzone przy pomocy spektroskopii impedancyjnej. Stosując przewodzące...
-
COMPUTER-AIDED CONSTRUCTION AT DESIGNING REINFORCED CONCRETE COLUMNS AS PER EC
PublicationThe article presents the author’s computer program for designing and dimensioning columns in reinforced concrete structures taking into account phenomena affecting their behaviour and information referring to design as per EC. The computer program was developed with the use of C++ programming language. The program guides the user through particular dimensioning stages: from introducing basic data such as dimensions, concrete...
-
A role of destructive and non-destructive tests in creep damage Identification
PublicationPrzedstawiono wyniki badań mjących zilustrować i określić rolę badań niszczących i nieniszczących w identyfikowaniu degradacji po pełzaniu
-
Data-Driven Modeling of Mechanical Properties of Fiber-Reinforced Concrete: A Critical Review
PublicationFiber-reinforced concrete (FRC) is extensively used in diverse structural engineering applications, and its mechanical properties are crucial for designing and evaluating its performance. The compressive, flexural, splitting tensile, and shear strengths of FRCs are among the most important attributes, which have been discussed more extensively than other properties. The accurate prediction of these properties, which are required...
-
Damage localisation in a stiffened plate structure using a propagating wave
PublicationThe paper presents an application of changes in propagating waves for damage detection in a stiffened aluminium plate. The experimental investigation was conducted on an aluminium plate with riveted two L-shape stiffeners. The wave has been excited with a piezoelectric transducer and measured with the Laser Scanning Doppler Vibrometer. Recorded signals were analysed using the special signal processing techniques developed for damage...
-
Certain numerical issues of wave propagation modelling in rods by the Spectral Finite Element Method
PublicationW pracy omówiony zagadnienia związane z modelowaniem propagacji fal sprężystych metodą Spektralnych Elementów Skończonych. Przedstawiono wpływ postaci macierzy mas na błędy rozwiązania. Omówiono zakres stosowalności modeli.
-
Modelling of wave propagation in composite plates using the time domain spectral element method
PublicationW pracy przedstawiono wyniki obliczeń propagacji fali sprężystej w płycie kompozytowej modelowanej z wykorzystaniem czasowego sformułowania metody elementów spektralnych
-
IEEE TRANSACTIONS ON ANTENNAS AND PROPAGATION
Journals -
Fast Full-Wave Multilevel Zero-Pole Optimization of Microwave Filters
PublicationA new concept is proposed for the full-wave computer-aided design of microwave filters. The method consists of two stages and operates on the zeros and poles of the transfer function and their derivatives. These quantities are evaluated from the response computed by a full-wave electromagnetic solver with two levels of accuracy. The two stages make use of different models that are optimized using a low-accuracy electromagnetic...
-
Jacek Stefański prof. dr hab. inż.
PeopleJJacek Stefański received M.Sc., Ph.D. and D.Sc. degrees in telecommunications engineering from Gdansk University of Technology (GUT), Poland, in 1993, 2000 and 2012, respectively. Awarded title of Professor by the President of Poland in 2020. Currently, he works as a professor at the Department of Radio Communication Systems and Networks (DRCSN) in GUT. From 2005 to 2009, he worked as an assistant professor in the National Institute...
-
Simulations of spacing of localized zones in reinforced concrete beams using elasto-plasticity and damage mechanics with non-local softening
Publication -
Simulations of spacing of localized zones in reinforced concrete beams using elastic-plasticity and damage mechanics with non-local softening
PublicationArtykuł omawia obliczanie belek żelbetowych z uwzględnieniem lokalizacji odkształceń. Obliczenia wykonano przy zastosowaniu MES na bazie sprężysto-plastycznego prawa konstytutywnego i modelu zniszczeniowego uwzględniającego degradację sztywności rozszerzonego o długość charakterystyczną mikrostruktury za pomocą teorii nielokalnej.
-
JOURNAL OF NON-CRYSTALLINE SOLIDS
Journals -
Investigation of Continuous Wave Jamming in an IEEE 802.15.4 Network
PublicationThis paper presents how continuous wave jamming affects IEEE 802.15.4 network. To this end, an office-based measurement setup has been proposed. Within the measurement area, 25 nodes have been set up in order to create a IEEE 802.15.4 tree-based test network structure. A dedicated jamming device that generates and transmits a continuous wave signal has been developed. Several tests have been conducted and presented to demonstrate...
-
POLYMER TESTING
Journals -
Field-induced suppression of charge density wave in GdNiC2
PublicationWe report the specific heat, magnetic, magnetotransport, and galvanomagnetic properties of polycrystalline GdNiC 2 . In the intermediate temperature region above T N = 20 K, we observe large negative magnetoresistance due to Zeeman splitting of the electronic bands and partial destruction of a charge density wave ground state. Our magnetoresistance and Hall measurements show that at low temperatures a magnetic field-induced transformation from...
-
Charge density wave and large nonsaturating magnetoresistance in YNiC2 and LuNiC2
PublicationWe report a study of physical properties of two quasi-low-dimensional metals YNiC2 and LuNiC2 including the investigation of transport, magnetotransport, galvanomagnetic, and specific heat properties. In YNiC2 we reveal two subsequent transitions associated with the formation of weakly coupled charge density wave at TCDW=318K and its locking in with the lattice at T1=275K. These characteristic temperatures follow the previously...
-
Jumping Wave Characteristic during Low Plasticity Burnishing Process
PublicationDuring the low plasticity burnishing process of soft materials such as carbon steel with a hardness of up to 40 HRC (Rockwell grade) a raised structure of the material known as the Jumping Wave forms in front of the tool roll. This phenomenon significantly disturbs the burnishing process, but is very poorly described in the literature. This article presents studies of this phenomenon on the example of burnished 1.0562 steel. The...
-
High-Resolution Wind Wave Parameters in the Area of the Gulf of Gdańsk During 21 Extreme Storms
PublicationThis dataset contains the results of wind-wave parameter modelling in the area of the Gulf of Gdańsk (Southern Baltic). For the simulations, a high resolution SWAN model was used. The dataset consists of the significant wave height, the direction of the wave approaching the shore and the wave period during 21 historical, extreme storms. The storms were selected by an automatic search over the 44-year-long significant wave height...
-
Influence of effective width of flange on calculation and reinforcement dimensioning of beam of reinforced concrete frame
PublicationThe paper analyses the influence of modelling the cross-section of a beam in two-storey reinforced concrete frame of industrial warehouse with dimensions: 18.0 m × 32.0 m using bar elements on the results of bending moments, the value of elastic deflection and the dimensioning of reinforcement due to bending. Six options were considered: a beam as a rectangular section and five T-beam variants with different definitions of effective...
-
Wave transmission across surface interfaces in lattice structures
PublicationWithin the lattice dynamics formulation, we present an exact solution for anti-plane surface waves in a square lattice strip with a surface row of material particles of two types separated by a linear interface. The considered problem is a discrete analog of an elastic half-space with surface stresses modelled through the simplified Gurtin–Murdoch model, where we have an interfacial line separating areas with different surface...
-
Design of an Autonomous IoT Node Powered by a Perovskite-Based Wave Energy Converter
PublicationThis paper presents the results of experimental research focused on wave energy harvesting and its conversion to power Internet of Things (IoT) devices. The harvesting and conversion process was performed using a wave energy converter (WEC) consisting of a lead zirconate titanate piezoelectric ceramic perovskite material and a prototype power electronic circuit. The designed WEC was considered as a power supply for an end node...
-
Analytical Expression for the Time-Domain Discrete Green's Function of a Plane Wave Propagating in the 2-D FDTD Grid
PublicationIn this letter, a new closed-form expression for the time-domain discrete Green's function (DGF) of a plane wave propagating in the 2-D finite-difference time-domain (FDTD) grid is derived. For the sake of its verification, the time-domain implementation of the analytic field propagator (AFP) technique was developed for the plane wave injection in 2-D total-field/scattered-field (TFSF) FDTD simulations. Such an implementation of...
-
System setup and software for cyclic, staircase and square wave voltammetry measurements
PublicationHardware dedicated for electrochemical measurement sometimes does not allow performing certain voltammetry experiments. Staircase and square wave voltammetry, techniques which have many advantages comparing with standard voltammetric techniques, are rarely implemented in software controlling electrochemical measuring equipment. These methods, however, can be relatively easy realized with some addition...
-
IEEE Antennas and Wireless Propagation Letters
Journals -
High-resolution wind wave parameters in the area of the Gulf of Gdańsk during 21 extreme storms
Open Research DataThis dataset contains the results of wind-wave parameter modelling in the area of the Gulf of Gdańsk (Southern Baltic). For the simulations, a high resolution SWAN model was used. The dataset consists of the significant wave height, the direction of the wave approaching the shore and the wave period during 21 historical, extreme storms. The storms were...
-
Internal imaging of concrete fracture based on elastic waves and ultrasound computed tomography
PublicationThe condition assessment of concrete structures belongs to the greatest challenges of non-destructive testing. Monitoring the fracture process of concrete and detecting cracks at the earliest possible stage is a vital aspect to ensure the safety of civil engineering objects. The use of ultrasound tomography enables imaging the internal structure of a tested element. This study aims at the visualization of fracture damage in concrete...
-
Modeling the debonding process of osseointegrated implants due to coupled adhesion and friction
PublicationCementless implants have become widely used for total hip replacement surgery. The long-term stability of these implants is achieved by bone growing around and into the rough surface of the implant, a process called osseointegration. However, debonding of the bone–implant interface can still occur due to aseptic implant loosening and insufficient osseointegration, which may have dramatic consequences. The aim of this work is to...
-
Mechanical Performance and Environmental Assessment of Sustainable Concrete Reinforced with Recycled End-of-Life Tyre Fibres
PublicationThe presented research’s main objective was to develop the solution to the global problem of using steel waste obtained during rubber recovery during the tire recycling. A detailed comparative analysis of mechanical and physical features of the concrete composite with the addition of recycled steel fibres (RSF) in relation to the steel fibre concrete commonly used for industrial floors was conducted. A study was carried out using...
-
A procedure for the identification of effective mechanical parameters of additively manufactured elements using integrated ultrasonic bulk and guided waves
PublicationThe subject of the current work was a simple but robust novel two-stage procedure for the non-destructive determination of effective elastic constants using ultrasonic wave propagation. First, ultrasonic bulk wave velocities measured on cubic samples were used to calculate most of the elements of the stiffness matrix. Secondly, the remaining elements were determined using the dispersion curves of elastic guided waves measured on...
-
Laboratory fatigue assessment of large geocomposite-reinforced double-layered asphalt concrete beams
PublicationGeosynthetic reinforcement of asphalt layers has been used for several decades. Evaluation of the influence of these materials on pavement fatigue life is still ongoing, especially for new types of geocomposites. This paper presents the evaluation of fatigue performance of large asphalt concrete beams reinforced with a new type of composite in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions...
-
Laboratory fatigue assessment of large geocomposite-reinforced double-layered asphalt concrete beams
PublicationGeosynthetic reinforcement of asphalt layers has been used for several decades. Evaluation of the influence of these materials on pavement fatigue life is still ongoing, especially for new types of geocomposites. This paper presents the evaluation of fatigue performance of large asphalt concrete beams reinforced with a new type of composite in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions...
-
Restoration and preservation of the reinforced concrete poles of fence at the former Auschwitz concentration and extermination camp
PublicationThe objective of this study was to assess the present state of the reinforced concrete poles of fence at the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp. The poles were subjected to renovation about 10 years ago. After this time some deficiencies of applied renovation method were noticed. Cracks appeared between fresh and original part of concrete cover. Analysis of the reasons of these failures...
-
Restoration and preservation of the reinforced concrete poles of fence at the former Auschwitz concentration and extermination camp
PublicationThe objective of this study was to assess the present state of the reinforced concrete poles of fence at the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp. The poles were subjected to renovation about 10 years ago. After this time some deficiencies of applied renovation method were noticed. Cracks appeared between fresh and original part of concrete cover. Analysis of the reasons of these failures...
-
ENHANCED EVAPORATION OF THE DROPLETS OF CONDENSATE IN THE ASYMMETRICAL SHOCK WAVE ZONE
PublicationIn the low-pressure part of steam turbine, the state path usually crosses the saturation line in penultimate stages [4,5]. The formation and evolution of these droplets lower the performance of the wet stages of the turbines, and their effects on the efficiency are collectively known as wetness losses [4]. Nowadays, due to work of steam turbines at partial load, process of homogeneous and heterogeneous condensation still is current....
-
An Experimental Investigation of Pressure Wave Celerity During the Transient Slurry Flow
PublicationTransportation of slurries in pressure pipelines is an example of a complex flow due to specific parameters of transported medium. For practitioners, the economy of designing and maintenance is usually the most important factor. For this reason, most of hydrotransport installations are fairly simple; however, they become more vulnerable to negative effects of the transient flow which can occur in pressure pipelines. As the consequence,...
-
Verification of algorithms determining wave loads on support structure of wind turbine
PublicationThe offshore wind turbines require determination of wave loads on their support structure. This structure is fixed and, therefore, this problem is reduced to solving only the diffraction problem, which is determined by Laplace equation and conditions on the following boundaries: on the support structure, on the sea free surface and on its bottom, and at infinity on free surface. The linear problem was applied to determine the wave...
-
Application of the ISE Optimized Proportional Control of the Wave Maker in a Towing Tank
PublicationThis paper presents the improvement of the wave maker control system. The wave maker is a facility widely used in hydromechanics laboratories to generate waves in towing tanks. It is equipped with an electrohydraulic drive and an actuator submerged into water. The waves are generated to model the environmental conditions for physical experiments, performed on reduced-scale models of maritime objects. The physical experiments allow...
-
Examination of advanced isotropic constitutive laws under complex stress states in plain and reinforced concrete specimens
PublicationThe performance of advanced isotropic constitutive laws under complex stress states in plain and reinforced concrete specimens is investigated. Three different formulations are chosen: original Mazars model, Mazars mi model and model proposed by Pereira and coworkers. The degradation of the material in all formulations is described via a single variable, but a strain/stress state is taken into account via quite sophisticated relationships....
-
Optimized Computational Intelligence Model for Estimating the Flexural Behavior of Composite Shear Walls
PublicationThis article presents a novel approach to estimate the flexural capacity of reinforced concrete-filled composite plate shear walls using an optimized computational intelligence model. The proposed model was developed and validated based on 47 laboratory data points and the Transit Search (TS) optimization algorithm. Using 80% of the experimental dataset, the optimized model was selected by determining the unknown coefficients of...
-
Integrated Application of GPR and Ultrasonic Testing in the Diagnostics of a Historical Floor
PublicationThe paper presents the results of integrated ground penetrating radar (GPR) and ultrasonic testing (UT) measurements conducted on a historical floor in St. Nicholas’ Church, Gdańsk, Poland. The described inspection was the first stage of the technical state assessment of the building. The aim of the study was the detection of underfloor air gaps, which were observed in a few trial pits. The condition of the ground under the floor...
-
Jarosław Górski prof. dr hab. inż.
People -
The influence of reinforcement on load carrying capacity and cracking of the reinforced concrete deep beam joint
PublicationThe paper presents the results of experimental research of the spatial reinforced concrete deep beam systems orthogonally reinforced and with additional inclined bars. Joint of the deep beams in this research was composed of the longitudinal deep beam with a cantilever suspended at the transversal deep beam. The cantilever deep beam was loaded throughout the depth and the transversal deep beam was loaded at the mid-span by longitudinal...
-
REINFORCED CONCRETE SUPPORTING CONSTRUCTION OF THE STADIUM COVER FOR EURO 2012 IN GDAŃSK
PublicationIn the article structural issues that connected with the reinforced concrete supporting construction of the stadium roofing for EURO 2012 in Gdańsk were described. In the first part of the article the concept of stadium foundation were described. In the second the static - strength analysis for two variants fastening together individual foundation elements were made. The two assumed geometrically different concept of foundation...
-
Slow-wave fractal-shaped compact microstrip resonant cell
PublicationA novel fractal-shaped compact microstrip resonant cell (CMRC) featuring a strong slow-wave effect has been presented. Its vital usefulness in the process of microstrip line miniaturisation has been proved and experimentally validated on the basis of a compact 3-dB branch-line coupler illustrating the possibilities of the approach. A prototype example structure has been designed to mirror the characteristics of a conventional device,...