Search
displaying 1000 best results Help
Search results for: speed
-
Centrally Pivoted Tilting Pad Thrust Bearing with Carbon-Based Coated Collar—Experimental Results of Low- and Medium-Speed Operation
PublicationExperimental results of the research on a tilting pad thrust bearing with symmetrical pad support in the conditions of high loads and low speeds are presented in the paper. As described in the literature review, experimental results of tilting pad bearings at low speed/high load regime and transient conditions are rare. Unusual material selection - steel pad against a DLC-type coating on the collar was utilized. Such material combination...
-
Adaptive traffic optimization using Variable Speed Limits; Adaptacyjna optymalizacja ruchu drogowego przy pomocy zmiennych ograniczeń prędkości
PublicationVariable speed limits (VSL) is an intelligent transportation system (ITS) solution for traffic management. The speed limits can be changed dynamically in order to adapt to traffic, weather, or road surface conditions. This paper presents an approach for such an adaptive traffic control where the primary goal is to ensure traffic safety and efficiency of the traffic control system (fast response to dynamically changing traffic,...
-
Comparing combined gas tubrine/steam turbine and marine low speed piston engine/steam turbine systems in naval applications
PublicationPorównano układy napędowe okrętowe kombinowane turbina gazowa- turbina parowa oraz spalinowy okrętowy silnik tłokowy wolnoobrotowy - turbina parowa. Porównywano moce oraz zużycie paliwa oraz parametry pary świeżej układu turbiny parowej.
-
THE INFLUENCE OF HOUSING ARRANGEMENT AND INTERFERENCE ON PRELOAD AND THEORETICAL LIFETIME OF A SYSTEM OF TAPER ROLLER BEARINGS OF A HIGH SPEED SHAFT OF A WIND TURBINE GEARBOX
PublicationA system of two taper roller bearings can carry loads with a high ratio of axial load to radial load. Such a system was proposed for a wind turbine gearbox following the poor durability of original bearing design with the aim of increasing durability. Because of size limits, a proposed system is composed of two different taper roller bearings. Standard manufacturers’ catalogues do not provide information on recommended preload...
-
Volume optimization of high-speed surface-mounted permanent magnet synchronous motor based on sequential quadratic programming technique and analytical solution
Publication -
Improvement of Attention, Executive Functions, and Processing Speed in Elderly Women as a Result of Involvement in the Nordic Walking Training Program and Vitamin D Supplementation
Publication -
Validation of odor concentration from mechanical-biological treatment piles using static chamber and wind tunnel with different wind speed values
Publication -
Validation study on a new semi-empirical method for the prediction of added resistance in waves of arbitrary heading in analyzing ship speed trial results
Publication -
High-Speed Videoendoscopy Enhances the Objective Assessment of Glottic Organic Lesions: A Case-Control Study with Multivariable Data-Mining Model Development
Publication -
Validation study on a new semi-empirical method for the prediction of added resistance in waves of arbitrary heading in analyzing ship speed trial results
PublicationThis paper describes an open and extensive validation study carried out by the Specialist Committee on Ships in Operation at Sea (SOS) of the International Towing Tank Conference (ITTC) on the newly developed SHOPERA-NTUA-NTU-MARIC (SNNM) wave-added resistance prediction method. The SNNM method aims at a simple, fast and transparent determination of the added resistance in regular waves of arbitrary encounter directions, even when...
-
The influence of screw configuration and screw speed of co-rotating twin screw extruder on the properties of products obtained by thermomechanical reclaiming of ground tire rubber
PublicationThe results of our investigations on the process of continuous thermomechanical reclaiming of ground tire rubber (GTR) carried out using a twin screw extruder are presented.We used a co-rotating twin screw extruder with a special configuration of plasticizing unit, enabling generation of considerable shear forces. The influence of screw configuration and screw speed on breaking of chemical crosslink bonds contained in ground tire...
-
A small-signal sound speed and parameter of non-linearity B/Ain a ternary mixture. Examples of calculations of mixture consisting of air, water and water vapor
PublicationZostało wyliczone zaburzenie entropii z dokładnością do członów nieliniowych rzędu drugiego. Jedyne założenie ograniczające, toże para wodna i powietrze są gazami doskonałymi. Ostatecznie,parametr nieliniowości i prędkość fali akustycznej przedstawione jako rodzinę krzywych, zależnych od trzech parametrów. Przedstawiono ilustrację tych zależności.
-
Relationship among the Change of Direction Ability, Sprinting, Jumping Performance, Aerobic Power and Anaerobic Speed Reserve: A Cross-Sectional Study in Elite 3x3 Basketball Players
Publication -
The Influence of Stretch Rod Speed on the Relationship between Preblown Bottle Aesthetic Quality and Final Blown Bottle Thickness Profile in Stretch Blow Molding from Preform Process
PublicationFrom a mechanical point of view, the aesthetic quality of preblown PET bottles and thickness profile of final blown PET bottles manufactured in ISBM process are determined by mechanical and thermal response of blown preforms. From the microscopic point of view the biggest influence on the mechanical and thermal properties of PET bottles have orientation and crystallization processes. From a technological point of view, the aesthetic...
-
Graphical presentation of the power of energy losses and power developed in the elements of hydrostatic drive and control system. Part I. Rotational hydraulic motor speed series throttling control systems
PublicationZaproponowano i uzasadniono wykres przedstawiający kierunek wzrostu strumienia mocy narastającej od wału lub tłoczyska silnika hydraulicznego do wału pomopy, mocy narastającej w wyniku wymuszania przez moce strat energetycznych występujących w elementach układu i sterowania hydrostatycznego. Przedstawiono interpretację graficzną mocy strat energetycznych występujących w elementach układów, a także mocy rozwijanych przez te elementy....
-
Graphical presentation of the power of energy losses and power developed in the elements hydrostatic drive and control system. Part II. Rotational hydraulic motor speed parallel throtling control and volumetric control systems
PublicationPrzedstawiono interpretację graficzną mocy strat energetycznych występujących w elementach układów napędu i sterowania hydrostatycznego, a także mocy rozwijanych przez te elementy. Dokonano analizy układu indywidualnego ze sterowaniem dławieniowym równoległym prędkości silnika hydraulicznego obrotowego, układu indywidualnego ze sterowaniem objętościowym, pompą o zmiennej wydajności, prędkości silnika hydrailicznego obrotowego,...
-
Speed, alcohol and safety belts as important factors influencing the number voivodship = Prędkość, alkohol i pasy bezpieczeństwa jako istotne czynniki wpływające na liczbę ofiar śmiertelnych wypadków drogowych na obszarze województw
PublicationNiniejszy referat prezentuje wyniki wstępne szerszego programu prac badawczych dotyczących bezpieczeństwa ruchu drogowego na obszarach województw.
-
Determination of pesticides in water using new solid phase extraction technique - speedisk and speedisk column.
PublicationW publikacji opisano zastosowanie nowych narzędzi do ekstrakcji do fazy stałej: szybkie dyski i szybkie kolumienki (speedisk i speedisk column). Zaprezentowano ich zastosowanie do ekstrakcji pestycydów z próbek wody, przy zastosowaniu różnych rozpuszczalników.
-
The Speedup Analysis in GEM Detector Based Acquisition System Algorithms with CPU and PCIe Cards
Publication -
Determination of optimal rotational speeds of circular saws
PublicationW pracy przedstawiono możliwości diagnostyczne stanowiska HewSaw do badania zachowania się pił w funkcji prędkości obrotowej piły. Wykazano, ze wyznaczone wartości prędkości optymalnych badanych pił leżą poniżej wartości zalecanych przez producenta. Praca z prędkościami wyższymi od optymalnych może prowadzić do zwiększenia strat materiałowych, a także stwarzać zagrożenia dla obsługi.
-
Chatter surveillance with the creation of a map of optimal spindle speeds
PublicationW pracy przedstawiono metodę nadzorowania drgań samowzbudnych typu chatter. Wyznaczono wartości optymalnych prędkości obrotowych wrzeciona dla poszczególnych punktów na powierzchni przedmiotu obrabianego, wykorzystując rożne techniki analizy modalnej. Badania eksperymentalne wykazały, że otrzymana w ten sposób mapa optymalnych prędkości obrotowych wrzeciona jest skutecznym narzędziem do eliminacji drgań chatter w procesie obróbki...
-
The effect of a belt position in the spindle driving system on critical rotational speeds
PublicationThe aim of this paper was to examine how the belt pulley position affects critical rotational speeds of the modernized spindle of the sliding table saw Fx3. Methodology of determination of critical rotational speeds of the spindle in a function of the spindle design features and its driving system is presented. Spindles in these kind of machine tools are mainly driven with V-belts, and the pulleys on the spindles might be positioned:...
-
Simplified Map-based Selection of Optimal Spindle Speeds When Milling Complex Structures
PublicationIn the paper a method for selecting optimal spindle speeds for complex structures during milling operations is presented. It is based on the selection of the spindle speed in accordance with a simple equation resulting from the minimisation of vibration energy, which leads to the minimisation of the work of cut-ting forces presented in previous elaborations by the authors [1]. Optimal spindle speeds are obtained for many points...
-
Modelling of laminated glass PVB walls of buildings exposed to vehicle impact with different speeds
PublicationThis paper presents an analytical model, developed for laminated glass subjected to a low-velocity impact. It has the ability to capture glass cracks as well as large non-linear deformations. It is based mathematically on the firstorder deformation concept, which considers the effect of membrane and transverse shear as well as bending. This theory uses damage mechanics to capture the glass cracking. For this purpose, several experiments...
-
Analysis of turnouts with non-linear curvature of diverging track for different train running speeds
PublicationThe paper deals with the issue of shaping a variable curvature in the diverging track of the railway turnout. Solution without a circular arc in the central zone, comprising two zones of non-linear curvature, of the same length, having zero curvature values at the end points, was adopted as a model, on the basis of the previously conducted dynamic tests. Optimum type of curvature was selected from the point of view of the kinematic...
-
Limitations of the Chladni patterns method for determination of circular saw blade critical rotational speeds
PublicationW pracy przedstawiono wyniki badań eksperymentalnych pił tarczowych z zastosowaniem figur Chladniego do wyznaczania obrotowych prędkości krytycznych pił tarczowych. Otrzymane wyniki wykazały, że w przypadku pił tarczowych o bardziej skomplikowanej budowie z długimi szczelinami, figury Chaldniego opisują postaci drgań, definiują częstotliwości rezonansowe. Jednakże, nie są one przydatne do wyznaczania obrotowych prędkości krytycznych...
-
Determination of the minimal critical rotational speeds of the circular saw blades with the quasi-twin resonant frequencies
PublicationTo determine the minimal critical rotational speeds of the circular saw blades is the fundamental aspect of obtaining the range of the rotational operating speeds, by which the circular saw blade can work with required stability. While for the circular saw blades with full-homogeneous bodies the determination of such rotational speeds is the relatively low level of difficulty function, whereas for circular saw blades with more...
-
Analyses of the effect of the design features of the spindle of the sliding table saw upon its critical rotational speeds
PublicationProducenci pilarek formatowych do drewna dążą do zwiększania dokładności przecinania. Można to osiągnąć np. przez poprawę zachowania się wrzeciona, gdyż od niego w dużej mierze zależą efekty przecinania. Przedstawiono metodykę wyznaczania prędkości krytycznych wrzeciona pilarki formatowej w funkcji cech konstrukcyjnych wrzeciona i jego napędu.
-
The Experimental Determination of Bearings Dynamic Coefficients in a Wide Range of Rotational Speeds, Taking into Account the Resonance and Hydrodynamic Instability
PublicationMethods for the experimental determination of dynamic coefficients are commonly used for the analysis of various types of bearings, including hydrodynamic, aerodynamic and foil bearings. There are currently several algorithms that allow estimating bearing dynamic coefficients. Such algorithms usually use various excitation techniques applied to rotor–bearings systems. So far only a small number of scientific publications show how...
-
Determination of pharmaceutical residues in drinking water in Poland using a new SPE-GC-MS(SIM) method based on Speedisk extraction disks and DIMETRIS derivatization
Publication -
Measurements of drive system properties of the "Magnetic SpeedLine" ultra-fast robot prototype for IML labeling
Open Research DataTests of the drive system of the ultra-fast robot "SpeedLine magnetic" for labeling with the IML method were carried out in order to analyze the influence of the operating parameters of the drive system on the correctness and quality of the drive system.
-
Measurements of the mechanical system properties of "SpeedLine magnetic" ultra-fast robot prototype for IML labeling
Open Research DataThe mechanical system tests of the high-speed IML labeling robot "SpeedLine Magnetic" were carried out in order to analyze the effects of the drive system's operating parameters on vibration and noise.
-
Measurements of power supply system properties of "Magnetic SpeedLine" ultra-fast robot prototype for IML labeling
Open Research DataTests of the power supply system of "SpeedLine magnetic" ultra-fast industrial robot for IML labeling were carried out to analyze the effect of the active power filter (APF) parameters on the power quality. at the target duty cycle. Tests were performed with the target duty cycle. Linear synchronous motors with permanent magnets were used to drive...
-
Michał Michna dr hab. inż.
PeopleMichal Michna received the M.Sc. and Ph.D. degrees in electrical engineering from the Gdansk University of Technology (GUT), Gdansk, Poland, in 1998 and 2005, respectively. Since 2004, he was employed at the Department of Power Electronics and Electrical Machines of the Gdańsk University of Technology (assistant, assistant professor, senior lecturer). In 2010-2015 he was a deputy of head of the Department of Power Electronics and...
-
Natalia Stawicka-Morawska dr inż.
PeopleMgr inż. Natalia Stawicka-Morawska pracuje na Politechnice Gdańskiej od października 2017 r. na stanowisku Asystenta, na Wydziale Inżynierii Mechanicznej i Okrętownictwa (poprzednio: Wydziale Mechanicznym), w Instytucie Mechaniki i Konstrukcji Maszyn (poprzednio: Katedrze Mechaniki i Mechatroniki).Prowadzona przez nią działalność naukowa dotyczy dziedziny nauk technicznych w dyscyplinie naukowej budowa i eksploatacja maszyn. Główną...
-
Jarosław Guziński prof. dr hab. inż.
PeopleJaroslaw Guzinski received M.Sc., Ph.D. and D.Sc. degrees from the Electrical Engineering Department at Technical University of Gdansk, Poland in 1994, 2000 and 2011 respectively. Since 2016 he is Associate Professor at Gdansk University of Technology. Currently he is the head of the Department of Electric Drives and Energy Conversion. From 2006 to 2009 he was involved in European Commission Project PREMAID Marie Curie, ‘Predictive...
-
Mathematical and numerical modelling, L, IDE, sem. 01, summer 21/22,(M:00057379)
e-Learning CoursesModelling. Optimal control. Modal analysis. High speed milling. Mechatronic design.
-
Mariusz Deja dr hab. inż.
PeopleAssistant Professor in the Department of Manufacturing Engineering and Automation. He graduated in 1993, obtaining Master degree at the Faculty of Mechanical Engineering, Gdańsk University of Technology in the field of study: Mechanical Engineering, specialization: Technological Process Design. After graduation he worked for the Department of Manufacturing Engineering and Automation and his main research area was associated with...
-
Permanent traffic counting stations - Expressway S6 in Gdansk (dataset containing 5-min aggregated traffic data and weather information)
Open Research DataThe data includes traffic data from permanent traffic count station located on the expressway S6 in the Tri-City Agglomeration area in Poland. The data covers the three year period between 2014 and 2017 and one direction of traffic (southbound).
-
Zdzisław Kowalczuk prof. dr hab. inż.
PeopleZdzislaw Kowalczuk received his M.Sc. degree in 1978 and Ph.D. degree in 1986, both in Automatic Control from Technical University of Gdańsk (TUG), Gdańsk, Poland. In 1993 he received his D.Sc. degree (Dr Habilitus) in Automatic Control from Silesian Technical University, Gliwice, Poland, and the title of Professor from the President of Poland in 2003. Since 1978 he has been with Faculty of Electronics, Telecommunications and Informatics...
-
Investigating the Impact of Weather Conditions and Time of Day on Traffic Flow Characteristics
PublicationAdverse weather such as rain, snow, and fog may significantly reduce visibility or change adhesion properties and, as a consequence, affect drivers’ sense of safety, driving comfort, and their reaction to a changing driving environment (i.e., lower speed and increased headways). The changed behavior of individual drivers affects both traffic flow characteristics, that is, average speed and headways, and parameters related to highway...
-
Marek Przyborski dr hab. inż.
PeopleMarek Przyborski (b. March 20, 1964. Chełmża) - His fields of interest are remote sensing and close range photogrammetry. He conducts research on the use of so-called "high-speed cameras" to analyze the rapidly-changing phenomena. Co-author and author of publications dealing with the wide meaning of remote sensing applications related to the construction, transport, engineering, environment and homeland security. He is the author...
-
Krzysztof Jan Kaliński prof. dr hab. inż.
PeopleKrzysztof J. Kaliński completed his MSc study at Gdańsk University of Technology (GUT) Faculty of Production Engineering (1980, result – get a first). He obtained PhD at GUT Faculty of Machine Building (1988, result – get a first), DSc at GUT Faculty of Mechanical Engineering (ME) (2002, result – get a first), and professor’s title – w 2013 r. In 2015 r. he became full professor, and since 2019 - professor.His research area includes:...
-
Data from 76- to 81-GHz mmWave Sensor located at S7 road
Open Research DataThe set consists data recorded employing IWR1642 mmWave sensor from Texas Instruments. The purpose of the experiment was to detect vehicles and their speed in real conditions – at S7 road, near Dworek village (54°14'40.0"N 18°59'59.0"E).
-
Karol Grębowski dr inż.
PeopleKarol Grębowski (M.Sc.) works as an assistant at the Department of Technical Fundamentals of Architecture Design of the Faculty of Architecture at Gdansk University of Technology. His scientific research deals with dynamic phenomena occurring during the vibration of structures, bridges, and studies the design methodology of the elements forming passive protection system of the vehicles degraded by struck or explosion in the context...
-
Resonant and nonresonant excitation of waves in a planar magnetosonic flow
PublicationForced propagation of perturbations in a magnetosonic wave are considered. The driving force may be caused by stimulated Mandelstam–Brillouin scattering of optic waves or by intense magnetosonic exciter. Some heating-cooling function which takes into account radiative cooling and unspecified heating is taken into consideration, as well as nonlinearity of a medium. Both these factors make the excitation particular. The analytical...
-
Five-phase induction motor drive with sine-wave filter
PublicationThe paper presents closed loop ac drive with 5 phase induction motor operating with voltage source inverter and sine wave filter. The motor supply voltages and currents have sinusoidal shape. For well known adjustable electric drives the field oriented control method with flux and speed co ntrol can be applied. In the presence of output filter both control and estimation algorithms should be modified due to sine wave filter installation....
-
Tribological test for evaluation of Natural PEEK
Open Research DataTest of PEEK natural (beige color) samples with sliding speed up to 1,2 m/s and up to 8 MPa of nominal load
-
DYNAMIC ANALYSIS OF HISTORIC RAILWAY BRIDGES IN POLAND IN THE CONTEXT OF ADJUSTING THEM TO PENDOLINO TRAINS
PublicationThe article presents the dynamic analysis of the historic railway bridge in Tczew as an example of the usefulness of such type of bridge for high-speed trains. The model of the bridge and the simulation of rolling stock passage was performed in SOFISTIK program. The scope of work includes experimental studies, the solution of the problem concerning the correct solution features dynamic model takes into account the dependencies...
-
MACHINE VISION DETECTION OF THE CIRCULAR SAW VIBRATIONS
PublicationDynamical properties of rotating circular saw blades are crucial for both production quality and personnel safety. This paper presents a novel method for monitoring circular saw vibrations and deviations. A machine vision system uses a camera and a laser line projected on the saw’s surface to estimate vibration range. Changes of the dynamic behaviour of the saw were measured as a function of the rotational speed. The critical rotational...