displaying 1000 best results Help
Search results for: AIR HEAT EXCHANGER
-
Investigation of Air Quality beside a Municipal Landfill: The Fate of Malodour Compounds as a Model VOC
PublicationThis paper presents the results of an investigation on ambient air odour quality in the vicinity of a municipal landfill. The investigations were carried out during the spring–winter and the spring seasons using two types of the electronic nose instrument. The field olfactometers were employed to determine the mean odour concentration, which was from 2.1 to 32.2 ou/m3 depending on the measurement site and season of the year. In...
-
Operation of the 900 MW power plant with the ORC supplied from three heat sources
PublicationThe chapter is aimed at utilisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90°C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach to increase...
-
Analysis of inductive power transfer systems for variable air gap and voltage supply frequency
PublicationThe paper describes an IPT system, by which electrical energy may be transmitted through a large air gap between coils without electrical connection. It presents theoretical and simulation analysis of IPT, which allows for supplying a receiver in the conditions of slow, in relation to the dynamics of power supply, changes in dimension of the air gap. The influence of frequency characteristics of the system on the possible selection...
-
Analysis of magnetic disturbances of air platform caused by induced magnetisation
PublicationMagnetometric systems installed on air platforms like airplanes or helicopters are equipped in compensators of magnetic disturbances. Time changes of the platform's position caused generation of magnetic disturbances. The permanent and induced magnetization of ferromagnetic elements and eddy currents induced in conducting parts of the platform are sources of these disturbances. The linear model of magnetic disturbances of platforms...
-
Inverse heat transfer problem solution of sounding rocket using moving window optimization
PublicationAn Inverse Heat Transfer Problem is solved for a sounding rocket module given its geometry and measured temperature profile. The solution is obtained via moving window optimization, a technique for solving inverse dynamics. An analysis is performed to modify the method to avoid oscillatory behavior of the resulting heat flux profile. The method parameters are tuned in relation to characteristic phases of the flight. Results are...
-
The In-House Method of Manufacturing a Low-Cost Heat Pipe with Specified Thermophysical Properties and Geometry
PublicationVarious types of heat pipes are available to purchase off the shelf, from various manufacturers, but most of them have strictly defined geometry and technical parameters. However, when there is a need to use a heat pipe (HP) with an unusual size and shape or working conditions other than the standard ones, it becomes very costly to order them from manufacturers, especially in small quantities, and only a few producers are willing...
-
Numerical investigation on distribution characteristics of oxidation air in a lime slurry desulfurization system with rotary jet agitators
PublicationRotary jet agitator is an effective device for mixing, dispersing, dissolving, and suspending dispersed phases in liquid, and is particularly advantageous to the homogenization of oxygen-enriched air within the lime slurry desulfurization system. The distribution of oxygen-enriched air in agitators is vital for the process of gypsum crystallization and the homogeneous and sufficient oxygen-enriched air can promote the formation...
-
Determination of Moisture Content Profiles of Spruce Wood After High Temperature Process and Air Drying
PublicationThe results of moisture content of wood after the process of its drying under high temperature conditions and air drying are presented. Wood samples, namely spruce (Picea abies Karst.) from the northern part of Pomerania region in Poland, were subject of steam and air drying.The aim of experiments was to measure moisture content of wood in its cross sections using moisture meter WRD-100. The samples of thickness 70 mm and length...
-
Methods of deep modification of low-bearing soil for the foundation of new and spare air runways
PublicationAfter analyzing the impact of aircraft on the airport pavement (parking spaces, runways, startways), it was considered advisable to consider the problem of deep improvement or strengthening of its subsoil. This is especially true for low-bearing soil. The paper presents a quick and effective method of strengthening the subsoil intended for the construction of engineering structures used for civil...
-
Numerical single-phase modeling of turbulent flow and heat transfer of nanofluids
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000< Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with published experimental data.
-
Correlation between Compressive Strength and Heat of Hydration of Cement Mortars with Siliceous Fly Ash
PublicationThis paper presents the results of calorimetric and strength tests of mortars with ordinary Portland cement and two substitution rates (10 and 20%) of cement by siliceous fly ash. The prepared samples were cured under isothermal conditions at four different temperatures: 23, 33, 43 and 53 °C. Heat of hydration was measured using an isothermal calorimeter dedicated to monitor the hydration process of cementitious composites such...
-
Comparative Evaluation of Selected Biological Methods for the Removal of Hydrophilic and Hydrophobic Odorous VOCs from Air
PublicationDue to increasingly stringent legal regulations as well as increasing social awareness, the removal of odorous volatile organic compounds (VOCs) from air is gaining importance. This paper presents the strategy to compare selected biological methods intended for the removal of different air pollutants, especially of odorous character. Biofiltration, biotrickling filtration and bioscrubbing technologies are evaluated in terms of...
-
approximation of photonic crystal fibres with large air holes by the step index fibre model
PublicationAn equivalent step index fibre with a silica core and air cladding is used to model photonic crystal fibres with large air holes. We model this fibre for linear polarisation (we focus on the lowest few transverse modes of the electromagnetic field). The equivalent step index radius is obtained by equating the lowest two eigenvalues of the model to those calculated numerically for the photonic crystal fibres. The step index parameters...
-
The Impact of Forms of Buildings on the Air Exchange in Their Environment. Based on the Example of Urban Development in Warsaw
PublicationPossibilities for energy-efficient, natural ventilation of buildings in an urban environment depend on the airflow around them. This chapter deals with the issue of dependence of air exchange in urban spaces on the building forms used in them and on relative position of these buildings. The authors focused on the problem of air stagnation in dense urban development. This phenomenon increases the energy demand of buildings. The...
-
Heat Transfer-Asian Research
Journals -
Frontiers in Heat and Mass Transfer
Journals -
Interfacial Phenomena and Heat Transfer
Journals -
Particulate Matter Production of Small Heat Source Depending on the Bark Content in Wood Pellets
PublicationWood pellets as biofuel are more and more used in small heat sources in Europe. Standard wood pellets are produced from wood sawdust without bark. The paper deals about the impact of bark in wood pellets on their properties and combustion process. Special attention in this work is paid to production of particulate matter during combustion of wood pellets depending on bark content. There were experimentally produced spruce wood...
-
Heat Transfer in Adsorption Chillers with Fluidized Beds of Silica Gel, Zeolite, and Carbon Nanotubes
Publication -
Optimization of combined heat and power (CHP) market allocation: The case of Poland
PublicationCombined heat and power (CHP), that is production of electricity and useful heat in a single thermodynamic process, is a way of primary energy saving and emission reduction. Therefore, promotion of the electricity from high-efficiency cogeneration (CHP-E) was encouraged in the European Union. However, CHP-E promotion mechanisms proved low effectiveness in certain countries, like Poland, where the prices of certificates of origin...
-
Heat Transfer of the Multicolor-Laser-Sources-Irradiated Nanoparticles in Reference to Thermal Processes
PublicationUnlike the standard materials, metallic nanoparticles offer enhancing the heat convertion rate which implies the maximum and average temperature boost significantly in the considered system. The work’s purpose is to examine heat transfer in the metallic nanoparticles which have been deposited on a glassy substrate, enabling the nanostructures thermoablation. Furthermore, the functionalized substrate is irradiated with multicolor-laser-sources,...
-
Pumping effect measured by PIV method in a multilayer spike electrode EHD device for air cleaning
PublicationDust particles can be harmful for human health when inhaled. Particularly dangerous are submicrometer dust particles, which can contain traces of toxic elements and can easily penetrate into the human respiratory system. Thus, efficient devices for the air cleaning from submicrometer dust particles are needed. Recently, Katatani and Mizuno have proposed an electrohydrody- namic (EHD) device for air cleaning for submicrometer particles....
-
Heat Transfer
Journals -
Selected problems of heat and mass transfer
e-Learning Courses -
Numerical methods in heat and fluid flow
e-Learning CoursesPrzedmiot odnosi się do bilansu masy pędu i energii w ujęciu 0D i 3D.
-
Selected problems of heat and mass transfer
e-Learning Courses -
Numerical methods in heat and fluid flow
e-Learning CoursesPrzedstawienie zagadnień dotyczących modelowania urządzeń instalacji energetycznych, w tym obiegów cieplnych termodynamicznych oraz wybranych urządzeń instalacji energetycznych przy użyciu kodów komercyjnych. Przedstawienie możliwości obliczeniowych kodu obliczeniowego typu CFD.
-
Characterisation of the interfacial heat transfer coefficient in hot stamping of titanium alloys
Publication -
Pressure drop and heat transfer during boiling and condensation at subcritical region
PublicationMost of the data presented in the literature relate to saturation temperatures in the range - 20°C to 40°C due to the application in refrigeration technology. There is necessity to extend databases to higher values of saturation temperature due to new applications such as Organic Rankine Cycle and high temperature heat pumps. Only few papers contain data for high reduced pressure for low boiling point liquids. This paper focus...
-
Gypsum dehydration in cement and its impact on air-void structure in air-entrained concrete
Publication -
Two-phase optimizing approach to design assessments of long distance heat transportation for CHP systems
PublicationCogeneration or Combined Heat and Power (CHP) for power plants is a method of putting to use waste heat which would be otherwise released to the environment. This allows the increase in thermodynamic efficiency of the plant and can be a source of environmental friendly heat for District Heating (DH). In the paper CHP for Nuclear Power Plant (NPP) is analyzed with the focus on heat transportation. A method for effectivity and feasibility...
-
An improved method for flow boiling heat transfer with account of the reduced pressure effect
PublicationIn the paper are presented the results using the authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data to investigate the sensitivity of the in-house developed model. In the work are presented the results of calculations obtained using the semi-empirical model on selected experimental flow boiling data of the refrigerants: R134a, R1234yf,...
-
High-quality Experiment Dedicated to microGravity Exploration, Heat Flow and Oscillation Measurement from Gdańsk
PublicationIn this paper we propose HEDGEHOG (High-quality Experiment Dedicated to microGravity Exploration, Heat flow and Oscillation measurement from Gdańsk) REXUS experiment to investigate vibrational and heat flow phenomena during the whole (ascent, microgravity phase, descent and recovery) flight of a sounding rocket. First, a proposed system of cantilever beams is discussed to study dynamic behaviour of dummy payload. Dimensioning has...
-
Use of Sensory Analysis Methods to Evaluate the Odor of Food and Outside Air
PublicationSensory analysis is applied in many areas of daily life. It is used to carry out the sensory evaluation of foodstuffs or other products and to evaluate the properties of odors present in the environment. The authors attempt to summarize the knowledge on the classification and application of sensory analysis methods to evaluate the odor nuisance of air, which allows the identification of sensory impressions and determination of...
-
Effect of asymmetric fluid flow distribution on flow boiling in a microchannel heat sink – An experimental investigation
PublicationFlow boiling in microchannels is emerging as an exclusive cooling solution for miniaturized high-power electronic devices alongside having other high heat flux applications. Size miniaturization at microscale strangely increases heat transfer performance as well as flow boiling instabilities. Many flow boiling instabilities are interrelated and result from imperfect hydrodynamic conditions. One of such problems is flow maldistribution among...
-
Analysis of Organic Rankine Cycle efficiency and vapor generator heat transfer surface in function of the reduced pressure
PublicationIn the paper presented is analysis of the influence of reduced pressure on efficiency and heat transfer area of vapor generator of Organic Rankine Cycle (ORC) in case of subcritical and supercritical parameters of operation. Compared are two cases of subcritical and supercritical ORC featuring a similar arrangement of heat source supply and heat removal, that is featuring the same temperatures of working fluid before the turbine,...
-
Changes in heat of vanadium xerogel powder under different atmosphere
Open Research DataThe DataSet contains the DSC curves of the vanadium xerogel powder. The information about xerogel powder synthesis is described in the Journal of Nanomaterials.
-
Air Pollutant Emission Measurement
Publication -
Monitoring of Gaseous Air Pollution
PublicationW pracy przedstawiono informacje dotyczące: - źródeł emisji zanieczyszczeń obecnych w powietrzu atmosferycznym; - norm i przepisów prawnych regulujących dopuszczalne poziomy zawartości poszczególnych ksenobiotyków w powietrzu atmosferycznym; - klasyfikacji metodyk monitoringu zanieczyszczeń obecnych w powietrzu; - zdalnego systemu monitoringu zanieczyszczeń powietrza atmosferycznego z wykorzystaniem zestawu odpowiednich czujników.
-
Experiment-Based Study of Heat Dissipation from the Power Cable in a Casing Pipe
PublicationThe paper deals with the important challenges in terms of electricity transmission by means of underground cable lines. The power cable’s performance is characterized by an ampacity that represents its maximum electric current-carrying capacity. The ampacity of power cables depends on their ability to diffuse the heat generated by the current flow into the environment. In the performed research, the analysis of the efficiency of...
-
Turbulent heat transfer in thin liquid films at low and high heat fluxes
PublicationW pracy przedstawiono rozważania turbulentnej wymiany ciepła w cienkich filmach cieczowych powstałych w wyniku uderzenia strugi przy małych i dużych strumieniach ciepła. W ostatnim przypadku może dojść do wrzenia filmu cieczowego. Oba zjawiska zamodelowano i uzyskano odpowiednie rozkłady temperatury i pedkosci.
-
Exploring the Institutional and Bottom-Up Actions for Urban Air Quality Improvement: Case Studies in Antwerp and Gdańsk
PublicationThe article presents the results of qualitative studies concerning the presence of air quality management in the process of urban planning and in the public discourse in Antwerp, Belgium, and Gdańsk, Poland. We focused on the way urban planners, environmental experts, and stakeholders perceive the problem of air pollution, especially with respect to urban development policy, and whether they consider it one of the major factors...
-
Prediction of flow boiling heat transfer coefficient for carbon dioxide in minichannels and conventional channels
PublicationIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of carbon dioxide. The experimental data from various resea rches were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house model. The results show the importance of taking into...
-
Enhanced Visible Light Active WO3 Thin Films Toward Air Purification: Effect of the Synthesis Conditions
PublicationTaking into consideration, our current environmental situation in the world people should face with growing problem of air and water pollution. Heterogeneous photocatalysis is highly promising tool to improve both, air and water quality through decomposition/mineralization of contaminations directly into harmless CO2 and H2O under ambient conditions. In this contribution we focused on the synthesis of self-assembly WO3 thin films...
-
Analysis of possibility and purposefulness of application of waste-heat boilers to trailing suction hopper dredgers
PublicationThis paper presents an analysis of possibility and purposefulness of application of waste-heat boilers to trailing suction hopper dredgers. Using results of own operational research on dredgers this author determined thermal power demand for six hypothetical trailing suction hopper dredgers of various size, at accounting for a type of power system and kind of fuel combusted by dredger's power plant. By means of basic indices of...
-
Small Scale Gasification of Biomass and Municipal Wastes for Heat and Electricity Production using HTAG Technology
PublicationCombustion and gasification technology utilizing high-cycle regenerative air/steam preheater has drawn increased attention in many application areas. The process is to be realized at temperature level above ash melting point using highly preheated agent. The use of highly preheated media above 900degC provides additional energy to conversion processes and results in considerable...
-
Heat and mass transfer in lack of gravity
e-Learning Courses -
Heat and mass transfer in lack of gravity
e-Learning Courses -
Removal of Volatile Organic Compounds (VOCs) from Air: Focus on Biotrickling Filtration and Process Modeling
PublicationBiotrickling filtration is a well-established technology for the treatment of air polluted with odorous and volatile organic compounds (VOCs). Besides dozens of successful industrial applications of this technology, there are still gaps in a full understanding and description of the mechanisms of biotrickling filtration. This review focuses on recent research results on biotrickling filtration of air polluted with single and multiple...
-
A new method for determination of flow boiling heat transfer coefficient in conventional diameter channels and minichannels
PublicationW pracy przedstawiono rozważania związane z modelowaniem wrzenia w przepływie w kanałach o średnicach konwencjonalnych, małych i minikanałach. Przedstawiono przegląd podejść do modelowania wymiany ciepła i w tym świetle przedstawiono oryginalne podejście autora. W przeciwieństwie do innych podejść metoda autora ma zastosowanie zarówno do kanałów o średnicach konwencjonalnych i minikanałach. Przedstawiono zadowalające porównania...