Search
Search results for: SOLID PARTICLES
-
Possibilities of radioisotope measuring in control of an unstable solid particles hydrotransport
PublicationThe paper presents γ-radiation proposal to control a multiphase flow, independently from circumstances. So this method may be applied even in compound industrial or environmental processes. Moreover in many cases, it is the only method for applications for dense mixture containing coarse angular grains. The constructed equipment allows continuous measurement of density as well as solid phase for both concentration and average velocity....
-
Terminal and hindered settling of solid particles in O/W emulsions
PublicationProwadzono badania szybkości opadania swobodnego cząstek stałych w emulsjach typu O/W oraz sedymentacji zawiesin ciało stałe - emulsja. Zbadano wpływ stężenia zawiesiny na szybkość sedymentacji. Opracowano zależność na prędkość opadania cząstek stałych w zawiesinacjh w emulsjach O/W w zakresie ruchu laminarnego.
-
Sliding bearings with sintered bronze bush lubricated by contaminated water with solid particles – Theoretical and experimental studies
PublicationSliding journal bearings lubricated with water coming directly from the environment are a solution used in shipbuilding, pumps and hydropower. However, the working fluid or surrounding water cannot always be filtered because of design limitations, which often causes the problem of premature wear of these sensitive bearings. The research conducted made it possible to assess the wear of sliding bearings lubricated with water containing...
-
Construction and investigation of SO2 amperometric sensor with a solid polymer electrolyte membrane
Publicationn this paper a sensor for detection of the sulphur dioxide based on three electrode cell configuration with a liquid electrolyte, a mercury sulphate reference electrode and a solid polymer electrolyte working electrode is presented. Working elec- trode was obtained by using Takenaka-Torikai chemical deposi- tion method by precipitation of Au particles into the pores of the Nafion membrane. Sensors characteristics measurements were...
-
The Progress in Electron Microscopy Studies of Particulate Matters to Be Used as a Standard Monitoring Method for Air Dust Pollution
PublicationThe present article reviews studies on air solid particles carried out with the use of electron microscopy. Particle analysis combining scanning and transmission electron microscopy (SEM and TEM) can be used to derive size-resolved information of the composition, mixing state, morphology, and complex refractive index of atmospheric aerosol particles. It seems that electron microscopy is more widely used in atmospheric particulate...
-
Analysis of radiometric signal in sedimentating suspension flow in open channel
PublicationThe article discusses issues related to the estimation of the sedimentating solid particles average flow velocity in an open channel using radiometric methods. Due to the composition of the compound, which formed water and diatomite, received data have a very weak signal to noise ratio. In the process analysis the known determining of the solid phase transportation time delay the classical cross-correlation function is the most...
-
Effect of Microplastics Pollution on Hydrogen Production from Biomass: A Comprehensive Review
PublicationHydrogen production from biomass and organic wastes is considered as a potential alternative energy source and is known as a clean and CO2-free fuel energy carrier. H2 is considered very promising among the other energy sources; therefore, the effective conversion of biomass and organic solid waste to this secondary energy source is urgently sought. As a result, it is of importance to assess the impact of the existence of microplastics...
-
Measurements of Two-phase Flows in Pipelines Using Radioisotopes and Statistical Signal Processing
PublicationThis paper presents an application of radiotracers and gamma absorption method in two-phase flow measurements in pipelines. Two different methods were implemented to analysis of acquired signals. Investigated methods are based on the cross-correlation function and the phase of the cross-spectral density distribution. The examples presented in the article illustrate the application of the radioisotopes to evaluation of liquid-gas...
-
The use of spectrometric diagnostics in identification of the technical condition of tribological systems
PublicationThe paper presents, as an effect of the analysis of investigation results, a possibility of using the spectrometric diagnostics in the tribological system technical condition supervision arrangement. A model, based on the emission of solid particles in tribological system operation, allows to identify the system technical condition. After the analysis of tests carried out with the use of that model, it has been found that the content...
-
Numerical modeling of the combustion in a lab-scale pulverized-coal fired combustion chamber
PublicationThis work presents results of numerical modeling of the combustion process inside a lab-scale drop-tube chamber, designed to investigate the slagging properties of the flue ashes, created through the solid fuel firing. Interaction between turbulence and chemistry is accounted by use of probability density function (PDF). FLUENT inputs for non-premixed combustion chemistry modeling are defined. A discrete second phase of the coal...
-
Numerical modeling of the combustion in a lab-scale pulverized-coal fired combustion chamber
PublicationThis work presents results of numerical modeling of the combustion process inside a lab-scale drop-tube chamber, designed to investigate the slagging properties of the flue ashes, created through the solid fuel firing. Interaction between turbulence and chemistry is accounted by use of probability density function (PDF). FLUENT inputs for non-premixed combustion chemistry modeling are defined. A discrete second phase of the coal...
-
INFLUENCE OF NANOPARTICLE CONCENTRATION ON THERMAL PROPERTIES OF THERMAL OIL-MWCNT NANOFLUID
PublicationThis paper deals with measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of thermal oil-MWCNT (TO-MWCNT) nanofluid. Nanoparticles were tested at the concentration of 0.001%, 0.005%, 0.01%, 0.05%, and 0,1% by weight. Ultrasonic vibration was used in order to stabilize the dispersion of the nanoparticles. Thermal oil (TO) was selected as a base liquid, because of possible application in ORC systems...
-
Effects of thermal history on the performance of low-temperature solid oxide fuel cells with Sm0.2Ce0.8O2-δ electrolyte and LiNi0.81Co0.15Al0.04O2 electrodes
PublicationIn this study, low-temperature solid oxide fuel cells with an ∼560 μm thick Sm0.2Ce0.8O2−δ (SDC) electrolyte and ∼890 μm thick LiNi0.81Co0.15Al0.04O2−δ (NCAL) electrodes are constructed and characterized under three experimental conditions. The cell with an NCAL cathode pre-reduced under an H2 atmosphere at 550 °C presents the best electrochemical performance. This is ascribed to facts that the reduction reaction generating Ni–Co...
-
Influence of nanoparticle concentration on thermal properties of thermal oil-MWCNT nanofluid
PublicationResults of the measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of thermal oil-MWCNT (TO-MWCNT) nanofluid have been presented. Nanoparticles were tested at the concentration of 0.001%, 0.005%, 0.01%, 0.05%, and 0,1% by weight. Thermal oil (TO) was selected as a base liquid, because of possible application in ORC systems as an intermediate heating agent. Multi-walled carbon nanotubes were used...
-
Characterization methods of nickel nano-particles obtained by the ex-solution process on the surface of Pr, Ni-doped SrTiO3 perovskite ceramics
PublicationIn this paper, a novel electrode material based on Pr, Ni co-doped strontium titanate ( Sr0.7Pr0.3)xTi1−yNiyO3 with constant amount of 30% praseodymium dopant, different amount of nickel (y = 0.06 and y = 0.10) and additional nonstoichiometry in Sr-site (x = 1; x = 0.9 and x = 0.8) was investigated as fuel electrode for SOEC devices. A porous ceramics were prepared by solid-state reaction method. X-ray diffraction measurements...
-
Recent advances on SOA formation in indoor air, fate and strategies for SOA characterization in indoor air - A review
PublicationRecent studies proves that indoor air chemistry differs in many aspects from atmospheric one. People send up to 90 % of their life indoors being exposed to pollutants present in gas, particle and solid phase. Particle phase indoor is composed of particles emitted from various sources, among which there is an indoor source – secondary chemical reactions leading to formation of secondary organic aerosol (SOA). Lately, researchers'...
-
Effects of Ni-NCAL and Ni–Ag electrodes on the cell performances of low-temperature solid oxide fuel cells with Sm0.2Ce0·8O2-δ electrolyte at various temperatures
PublicationThree low-temperature solid oxide fuel cells are built using Sm0.2Ce0·8O2-δ (SDC) as the electrolyte. Cell A is symmetrical and features Ni–LiNi0.8Co0·15Al0·05O2 (Ni–NCAL) electrodes, Cell B comprises a Ni–NCAL anode and a Ni–Ag cathode, and Cell C is fabricated using a Ni–NCAL cathode and a Ni–Ag anode. The ohmic resistance and polarization resistance (Rp) of Cells B and C are significantly higher than those of Cell A. The reduction...
-
Fracture simulations in concrete beam under bending using a mesoscopic model with cohesive elements
PublicationThe main aim of this paper was to investigate a complex fracture process in a concrete beam subjected to 3-point bending test by means of the 2D meso-scale FEM with 4-node cohesive elements embedded in the initial mesh of 3-node solid elements. The material heterogeneity was taken into account by considering 3 different phases (aggregate, cement matrix, ITZs) on the basis of randomly generated internal structure of concrete and...
-
Measurement of temperature-dependent viscosity and thermal conductivity of alumina and titania thermal oil nanofluids
PublicationThe results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil was selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from 20°C to...
-
MEASUREMENT OF TEMPERATURE-DEPENDENT VISCOSITY AND THERMAL CONDUCTIVITY OF ALUMINA AND TITANIA THERMAL OIL NANOFLUIDS
PublicationIn this study results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil is selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from...
-
Fabrication of ILs-Assisted AgTaO3 Nanoparticles for the Water Splitting Reaction: The Effect of ILs on Morphology and Photoactivity
PublicationThe design of an active, stable and ecient photocatalyst that is able to be used for hydrogen production is of great interest nowadays. Therefore, four methods of AgTaO3 perovskite synthesis, such as hydrothermal, solvothermal, sol-gel and solid state reactions, were proposed in this study to identify the one with the highest hydrogen generation eciency by the water splitting reaction. The comprehensive results clearly show that...
-
Tome-lapse X-ray tomography imaging of flow patterns in versatile silo model
PublicationThe paper introduces a new versatile silo model that was especially designed for in situ X-ray tomography studies of silo discharge for various flow conditions, namely concentric and eccentric. The presented work focuses on organic granular materials where low fraction of short-grain white rice is mixed with spheroidal sorghum particles. The high-quality tomography images combined with adequate image processing strategy allows...
-
Modulated crystal structures - periodicity in more than three dimensions
PublicationThe initial definition of a crystal was that it is an object with flat faces. When diffraction studies were developed it turned out that crystal consists of a highly ordered particles and it is possible to isolate a small unique part of their structure - a unit cell - and the definition has been changed to rely on this fact. Nowadays by a crystal we mean any solid having an essentially discrete diffraction diagram. It is because...
-
Insights Into Hydrodynamics of Spinning Fluids Reactor
PublicationSpinning fluids reactor (SFR) is one of the most efficient gas-liquid contacting system with high potential of application in many fields. The unique solution of SFR is the contacting of two spinning fluids which generated centrifugal force. The aim of this study was to investigate the pressure field distribution on the inner surface of reactors dispersing element. Obtained results confirm the high heterogeneity of the field pressure...
-
Measurements of Dispersed Phase Velocity in Two-Phase Flows in Pipelines Using Gamma-Absorption Technique and Phase of the Cross-Spectral Density Function
PublicationThis paper concerns the application of the gamma radiation absorption method in the measurements of dispersed phase velocity in two-phase flows: liquid–gas flow in a horizontal pipe- line and liquid–solid particles in a vertical pipe. Radiometric sets containing two linear 241Am gamma radiation sources and two NaI(Tl) scintillation detectors were used in the research. Due to the stochastic nature of the signals obtained from the...
-
An Influence of Factors of Flow Condition, Particle and Material Properties on Slurry Erosion Resistance
PublicationThe degradation of materials due to slurry erosion is the serious problem which occurs in the power industries. The paper presents actual knowledge about an influence of individual factors connected with flow conditions, particles and material properties on the slurry erosion resistance. Among the factors connected with operating conditions, an influence of impact angle, and velocity of impact, particle concertation and liquid...
-
One-step recovery of REE oxalates in electro-leaching of spent NdFeB magnets
PublicationRecovery of rare-earth elements (REEs) from spent NdFeB magnets is receiving great attention because of high amount of neodymium and potential risk of environmental pollution. In this study, a novel environment-friendly hydrometallurgical route is proposed for efficient recovery of REEs during electrochemical leaching with sulfuric and oxalic acids. With proper adjustment of the electrolyte composition and operating conditions,...
-
Badania połączeń spawanych rurociągu wody pitnej we Włocławku, ang. Welding joints tests in drinking water pipeline.
PublicationCelem badań opisanych w pracy było określenie przyczyn korozji powstałej w strefie wpływu ciepła (SWC) w obwodowych połączeniach spawanych w rurociągu wody pitnej. Materiałem, z którego wykonano rurociąg to stal 304/304L. W obszarze złącza spawanego stwierdzono wżery inicjowane od niezgodności geometrycznych, gdzie mogły gromadzić się osady zwiększające udział chlorków bezpośrednio przy powierzchni rury, promujące tym procesy korozyjne....
-
A pore-scale thermo–hydro-mechanical model for particulate systems
PublicationA pore scale numerical method dedicated to the simulation of heat transfer and associated thermo–hydro-mechanical couplings in granular media is described. The proposed thermo–hydro-mechanical approach builds on an existing hydromechanical model that employs the discrete element method for simulating the mechanical behavior of dense sphere packings and combines it with the finite volume method for simulating pore space fluid flow...
-
Proton Conducting Ceramic Powder Synthesis by a Low Temperature Method
PublicationMolten salt synthesis (MSS) is a simple method for the preparation of ceramic powders with specific morphology. The main role of the molten salts is to increase the reaction rate and lower the reaction temperature. It occurs because of much higher mobility of reactants in the liquid medium than in the solid state. In this work the molten salt synthesis was applied to produce ceramic powders of La0995Ca0005NbO4 and BaCe09−xZrxY01O3....
-
π-Stacking attraction vs. electrostatic repulsion: competing supramolecular interactions in a tpphz-bridged Ru(ii)/Au(iii) complex
PublicationThe synthesis and characterization of a mixed metal ruthenium(II)/gold(III) complex bridged by tetrapyridophenazine (tpphz) are described. It is isostructural and isoelectronic to the well-known photocatalysts with palladium(II) or platinum(II). Concentration dependent 1H-NMR spectroscopy and XRD studies show that the electrostatic repulsion between the gold(III) moieties exceeds the attractive π-stacking interaction. Theoretical...
-
Application of nanofluids in thermal technologies
PublicationNanofluids it is a relatively new category of thermal fluids that can serve as coolants, both in single- and two phase systems. However application of nanofluids in industrial applications requires faultless their thermophysical properties. Existing models originally developed for liquid/solid particles mixtures (slurries) fail in case of nanofluids. Moreover correlations used to calcuate heat transfer coefficients of conventional...
-
Magnetism from fundamentals to spintronics 22/23
e-Learning Courses1. Basic magnetic quantities2. Magnetism of atoms and molecules, atoms in external magnetic fields3. Solid state magnetism, types of magnetic materials (dia-, para-, and ferromagnetism)4. Ferromagnetism and domain structures5. Magnetism of small particles, single domain particles (StonerWohlfarth model), thin films6. Experimental techniques of magnetic properties and magnetisation state determination. Domain structurevisualisation...
-
Thermal utilization of meat-and-bone meal using the rotary kiln pyrolyzer and the fluidized bed boiler – The performance of pilot-scale installation
PublicationThermal utilization of meat-and-bone meal (MBM) is subject to stringent regulations that are meant to provide elimination of any potential pathogens. Incineration as well as other possible routes for thermal conversion of MBM are still at the research state. The universal technology was developed that allows to combust various types of waste organic materials, including animal waste, municipal solid waste and sludge, mixed at any...
-
Polybrominated diphenyl ether (PBDE) concentrations in dust from various indoor environments in Gdańsk, Poland: Prediction of concentrations in indoor air and assessment of exposure of adults
PublicationMonitoring of polybrominated diphenyl ethers (PBDEs) in indoor environments involves the determination of their concentrations in air, airborne particles, and settled dust. Each of these is a source of human exposure to PBDEs. In this study, we attempted to model PBDEs concentrations in various typical indoor environments on the basis of real PBDEs measurements in dust collected from them. The analytical procedure for determining...
-
Laser Welding of UNS S33207 Hyper-Duplex Stainless Steel to 6061 Aluminum Alloy Using High Entropy Alloy as a Filler Material
PublicationThe high entropy alloy (HEA) filler used during the fabrication method determines the reliability of HEAs for steel-aluminum dissimilar alloy configuration. HEAs have a direct impact on the formation of intermetallic compounds (IMC) formed by the interaction of iron (Fe) and aluminum (Al), and influence the size of the joint’s interaction zone. A novel welding process for Fe-Al alloy joints was developed to prevent the development...
-
Preparation and characterization of dummy-template molecularly imprinted polymers as potential sorbents for the recognition of selected polybrominated diphenyl ethers
PublicationThe main aim of this work was to conduct the preliminary/basic research concerning the preparation process of a new dummy molecularly imprinted polymer (DMIP) materials. Developed DMIPs were proposed as a sorption material in solid-phase extraction (SPE) technique for recognition of selected low mass polybrominated diphenyl ethers (PBDEs) e PBDE-47 and PBDE-99. Four new DMIPs were synthesized employing bulky polymerization technique...
-
Rheological properties of cement pastes containing pristine Bi2O3-Gd2O3 and silica coated Bi2O3-Gd2O3 core-shell structures
Open Research DataRheological data of cement pastes containing Bi2O3/Gd2O3 particles using MCR 72 (Anton Paar) stress-imposed rheometer, equipped with vane geometry.
-
Particle size distribution (laser granulometry) of pristine bismuth oxide (Bi2O3) and gadolinium oxide (Gd2O3) structures
Open Research DataData contain raw results of particle size distribution (by volume) of Bi2O3 and Gd2O3 particles determined using a laser diffraction method (Malvern Mastersizer 2000, Worcestershire, UK).
-
Review on mechanisms and efficiency of removal of microbiological contaminants in constructed wetlands
PublicationConstructed wetlands (CW) have been considered as a waste and a stormwater treatment systems for small communities or for areas with unsteady sewage flow conditions. Several investigations were undertaken for estimation suspended solids, organic matter and nutrients efficiency removal but only few focused on retention of microorganisms in constructed wetlands. In this review mechanisms of elimination of viruses, indicator bacteria...
-
Transmission electron microscope (TEM) and optical microscope images of pristine and silica-coated bismuth oxide and gadolinium oxide particles
Open Research DataCollection of raw transmission electron microscope (TEM) micrographs and optical microscope images used in the associated manuscript. All data in accessible *.tif format. Zip package contains:
-
Physicochemical and photocatalytic data of Cu-TiO2/Ti3C2 composites
Open Research DataIn this dataset, we include the data regarding the physicochemical properties (XRD, DR/UV-vis, photoluminescence, electrochemistry) and photocatalytic activity of TiO2/Ti3C2 and Cu-TiO2/Ti3C2 composites in the reaction of carbamazepine degradation. Herein we present the results for pure TiO2/Ti3C2 and composites modified with copper particles (0.25%,...
-
ThreSpect a program for the determination of the Appearance Energies
Open Research DataDataset presents the “ThreSpect” computer program dedicated to simulating threshold energies of neutral and ionized products generated in the collisions of photons or charged particles with atoms and molecules.
-
XRD patterns of nickel-modified V2CTx
Open Research DataThe set includes data for XRD pattern preparation of nickel-modified V2CTx samples.
-
Synthesis and structural properties of (Y, Sr)(Ti, Fe, Nb)O3−δ perovskite nanoparticles fabricated by modified polymer precursor method
PublicationThe yttrium, iron and niobium doped-SrTiO3 powders have been successfully fabricated by a modified low–temperature synthesis method from a polymer complex. The usage of strontium hydroxide precursor instead of conventional strontium nitrate or strontium carbonate provides to the possibility of significant decrease of annealing temperature. It allows to prepare a material with sphere-shape grains of nanometric size (15–70 nm). The...
-
Synthesis, microstructure and electrical properties of nanocrystalline calcium doped lanthanum orthoniobate
PublicationThe single phase lanthanum orthoniobate with tetragonal structure has been synthesized by the means of mechanosynthesis method. The studies have shown the crystal structure of La0.98Ca0.02NbO4 depends on the synthesis stage. The samples were predominantly in the tetragonal phase with a trace amount of the monoclinic phase. The SEM studies of morphology and microstructure have shown nanocrystallinity of the materials. The Raman...
-
Wastes from Agricultural Silage Film Recycling Line as a Potential Polymer Materials
PublicationThe recycling of plastics is currently one of the most significant industrial challenges. Due to the enormous amounts of plastic wastes generated by various industry branches, it is essential to look for potential methods for their utilization. In the presented work, we investigated the recycling potential of wastes originated from the agricultural films recycling line. Their structure and properties were analyzed, and they were...
-
Preparation and characterization of TiO2 nanostructures for catalytic CO2 photoconversion
PublicationThe titanium dioxide target (99.7%) of 1 cm in dia was ablated in vacuum by laser pulses(6 ns) at 266 nm and at repetition rate of 10 Hz. During deposition the laser fluence between 1 and 3.5 J/cm2 and the O2 pressure from the range of 10-2 - 1 Pa were applied. The thin TiO2 films were deposited on glass substrate (1 × 1 cm2) heated up to 500 °C. The chemical composition of the film and samples produced by annealing were investigated...
-
Emission of 1.3–10 nm airborne particles from brake materials
PublicationOperation of transport vehicle brakes makes a significant contribution to airborne particulate matter in urban areas, which is subject of numerous studies due to the environmental concerns. We investigated the presence and number fractions of 1.3–10 nm airborne particles emitted from a low-metallic car brake material (LM), a non-asbestos organic car brake material (NAO) and a train brake cast iron against a cast iron. Particles...
-
X-ray diffraction (XRD) and particle size distribution (PSD) data of iron oxide (Fe3O4) - magnetite particles
Open Research DataDataset presenting X-ray diffractogram and particle size distribution of nanomagnetite (Fe3O4) iron oxide particles purchased from Sigma Aldrich (637106).X-ray diffraction study was performed with a PRO X-ray diffractometer (X’Pert PRO Philips diffractometer, Co. Ka radiation, Almelo, Holland), while PSD was determined using laser diffraction technique...