Filters
total: 1066
filtered: 820
-
Catalog
- Publications 820 available results
- Journals 64 available results
- Publishing Houses 2 available results
- People 25 available results
- Inventions 1 available results
- Projects 4 available results
- Research Teams 1 available results
- e-Learning Courses 15 available results
- Open Research Data 134 available results
Chosen catalog filters
Search results for: PROTONIC CERAMICS
-
Characterization of magnesium doped lanthanum orthoniobate synthesized by molten salt route
PublicationMolten salt synthesis method has been used to prepare the single phase magnesium doped lanthanum orthoniobate. The phase composition has been checked by X-ray diffraction method and the microstructure studies have been performed by scanning electron microscopy. The high temperature properties of the material have been investigated by thermogravimetry and electrochemical impedance spectroscopy. A dependence between sample total...
-
In-situ Cu-doped MnCo-spinel coatings for solid oxide cell interconnects processed by electrophoretic deposition
PublicationThe Cu doping of the Mn–Co spinel is obtained “in-situ” by electrophoretic co-deposition of CuO and Mn1.5Co1.5O4 powders and subsequent two-step reactive sintering. Cu-doped Mn1.5Co1.5O4 coatings on Crofer22APU processed by electrophoretic co-deposition method are tested in terms of long term oxidation resistance and area specific resistance tests up to 3600 h. The introduction of Cu in the spinel lead to higher level of densification...
-
Effects of electrophoretic deposition times and nanotubular oxide surfaces on properties of the nanohydroxyapatite/nanocopper coating on the Ti13Zr13Nb alloy
PublicationLoad-bearing implants are developed with a particular emphasis placed on an application of ceramic hydroxyapatite coatings in order, to enhance the bioactivity of titanium implants and to shorten the healing time. Therefore, thin, fully crystalline coatings that are, highly adhesive, hydrophilic and demonstrating antibacterial properties are ly looked for. The aim of this research was to develop and characterize the properties...
-
Praseodymium substituted lanthanum orthoniobate: Electrical and structural properties
PublicationThe results of ionic transport and structural measurements for the lanthanum orthoniobate doped by praseodymium are presented and discussed. The influence of calcium co-doping on these properties has also been analyzed. The results suggest the predominant protonic conductivity for the investigated system in the whole range of investigated temperatures. The influence of calcium co-doping on phase purity is analyzed.
-
Influence of hydrogen on a nanocrystalline high-entropy oxide with application potential in hydrogen technologies
PublicationThe influence of hydrogen on a (Co0⋅2Cu0⋅2Mg0⋅2Ni0⋅2Zn0.2)O HEO with a rock salt structure was studied. Two forms of this HEO (nanopowder and sinter) were prepared via mechanochemical synthesis (MS) and additional heat treatment, respectively. The chemical stability of the synthesized samples in a pure hydrogen atmosphere was investigated using Sievert’s technique. High-pressure hydrogenation at 250 ◦C had no noticeable effect...
-
Tailoring optical constants of few-layer black phosphorus coatings: Spectroscopic ellipsometry approach supported by ab-initio simulation
Publication2D black phosphorus (BP) has attracted extensive attention as an anisotropic platform for novel optoelectronic and polarizing optics applications. Insight into the factors that tune the optical and polarizing properties of 2D BP reveals their essential influence on BP-based photonic and optoelectronic devices. In this work, studies of the optical constants of few-layer black phosphorus coatings are studied and discussed, with particular...
-
Self-supporting LSFO films for bolometers made with LTCC technology
PublicationOpisano metodę wytwarzania przewodzących, tlenkowych warstw ceramicznych tlenków lantanowo-strontowo żelazowych (LSFO) technologią low temperature co-fired ceramics (LTCC). Przedstawiono rezultaty pomiarów parametrów warstw pod kątem przydatności do produkcji detektorów IR.
-
Increasing the conductivity of V2O5-TeO2 glass by crystallization: structure and charge transfer studies
PublicationIn the present paper, V 2 O 5 -TeO 2 glass was prepared by the melt-quenching technique. Crystallization of glass with a vanadium content higher than 35%mol results in an increase in electrical conductivity by a few orders of magnitude and a decrease in activation energy from ~0.40 to ~0.12 eV. In this work, a critical review of existing charge transfer models was presented on the example of V 2 O 5 -TeO 2 glass and glass–ceramics....
-
Badanie właściwości czujników wilgotności na bazie nanocząstek tlenku cynku
PublicationW celu pomiaru wilgotności szeroko stosowane są czujniki elektryczne. Warstwą czynną, zmieniającą swoje właściwości pod wpływem pary wodnej, stanowią najczęściej materiały ceramiczne lub polimerowe. Tlenek cynku jest jednym z materiałów ceramicznych będących dobrym kandydatem do zastosowania go jako warstwy czynną w czujnikach wilgotności. W tej pracy przedstawiono wyniki badań właściwości struktur czujnikowych z warstwą tlenku...
-
Samonośne warstwy LSFO na bolometry wykonane technologią LTCC
PublicationOpisano sposób produkcji ceramicznych, przewodzących warstwtypu perowskitu z niestechiometrycznych tlenków lantanowo-strontowo żelazowych (LSFO) wykonanych technologią LTCC )low temperature co-fired ceramics). Zaprezentowano pomiary parametrów tych warstw, charakteryzujących ich przydatność do produkcji bolometrów.
-
Bioactive core material for porous load-bearing implants
PublicationSo far state of knowledge on biodegradable materials is reviewed. Among a variety of investigated materials, those composed of polymers and ceramics may be considered as only candidates for a core material in porous titanium alloy. The collagen and chitosan among natural polymers, polyhydroxy acids among synthetic polymers, and hydroxyapatite and tricalcium phosphate among ceramics are proposed for further research. Three essential...
-
Study of Phase and Chemical Composition of Bi1-xNdxFeO3 Powders Derived by Pressureless Sintering
PublicationIn the present paper studies on Bi1xNdxFeO3 for x =0.1-0.4 are reported. The mixed oxide method followed with pressureless sintering was employed for ceramics fabrication. Thermal behavior of stoichiometric mixtures of simple oxide powders, viz. Bi2O3, Nd2O3 and Fe2O3 was studied by simultaneous thermal analysis. It was found that with an increase in neodymium content the weight loss increased from 0.75% to 3.16% for x =0.1 and...
-
Bezpośrednia analiza próbek z wykorzystaniem techniki spektrometrii mas. Cz. II. Technika PTR – MS – ciekawe rozwiązanie metodyczne w zakresie spektrometrii mas
PublicationTechnika spektrometrii mas stanowi niezwykle istotne narzędzie badawcze, umożliwiające uzyskanie wielu cennych informacji, dotyczących składu chemicznego wielu próbek rzeczywistych pochodzenia biologicznego, farmaceutycznego i spożywczego. Spektrometr mas zazwyczaj pełni role detektora w przypadku stosowania połączenia z urządzeniami chromatograficznymi (GC, LC). Dzięki zastosowaniu pewnych modyfikacji aparaturowych i metodycznych,...
-
Materiały ceramiczne w łożyskach ślizgowych
PublicationOpisano obszary zastosowań ceramiki maszynowej w węzłach ślizgowych maszyn. Przedstawiono rodzaje ceramiki stosowane w łożyskowaniu ślizgowym. Przedstawiono produkowane fabrycznie ceramiczne łożyska ślizgowe.
-
Optymalizacja warunków pracy grubowarstwowych bolometrów LSFO
PublicationOpisano sposób produkcji bolometrów wykorzystujących ceramiczne, przewodzące warstwy typu perowskitu z niestechiometrycznych tlenków lantanowo-strontowo żelazowych (LSFO) wykonanych technologią LTCC (Low Temperature Co-fired Ceramics). Zaprezentowano wyniki pomiarów parametrów tych bolometrów oraz pozwalające na wybór optymalnych warunków pracy.
-
Effect of chemical composition on corrosion and wear behaviour of the composite Ni-Fe-Al2O3 coatings.
PublicationPrzedstawiono wyniki badań powłoki kompozytowej otrzymanej przez osadzanie katodowe galwaniczne w roztworze zawierającym sole niklu, żelaza oraz cząstki ceramiki Al2O3 o różnej wielkości i stężeniu. Wykazano, że charakterystyka ceramiki posiada wpływ na szybkość korozji i zużycia ściernego. W szczególności, zawartość ceramiki wpływa dodatnio na odporność na zużycie ścierne, ale nieco obniża odporność na zużycie korozyjne.
-
Barium boron aluminum silicate glass system for solid state optical gas sensors
PublicationRecent increasing demand for new eco-friendly materials and for low cost fabrication process for use in optical sensors field, raise concern about alternative materials for this application. We have designed two glass-ceramics compositions from the quaternary ROAl2O3- SiO2-B2O3(R=Ba) alkali-earth aluminum silicate system, labeled B72 and B69, with high refractive index (>1.6), large values of Abbe number (94.0 and 53.0, respectively),...
-
Gigantic electro-chemo-mechanical properties of nanostructured praseodymium doped ceria
PublicationSome oxygen defective fluorites are non-Newnham electrostrictors, i.e., the electromechanical response does not depend on their dielectric properties. Here, we show gigantic electrostriction in nanocrystalline 25 mol% praseodymium doped ceria (PCO) bulk ceramics. The material was fabricated with a fieldassisted spark plasma sintering (SPS) process from high-purity nanoscale PCO powders (<20 nm). The SPS process consolidates the...
-
Self-Organized Nanotubular Oxide Layers on Ti and Ti Alloys
PublicationTo improve bioactivity of titanium and titanium, the implant surface modification by formation of self-organized TiO2 nanotube arrays with electrochemical techniques is presented. The influence of electrolyte composition and deposition parameters during anodization is characterized. The enhancement of phosphates deposition by titanium nanotubular structure is discussed. The calcium phosphate ceramics is shown to be uniformly deposited...
-
Silicon oxycarbide-tin nanocomposite derived from a UV crosslinked single source preceramic precursor as high-performance anode materials for Li-ion batteries
PublicationIn this work, we report an innovative and facile UV light-assisted synthesis of a nanocomposite based on silicon oxycarbide (SiOC) and tin nanoparticles. SiOC ceramic matrix, containing a conductive free carbon phase, participates in lithium-ion storage, and buffers the volume changes of Li-alloying/de-alloying material. The reported synthesis procedure through a polymer-derived ceramic route involves the preparation of a single-source...
-
Modulation of dielectric properties in low-loss polypropylene-based composites at GHz frequencies: theory and experiment
PublicationPolymer composites with high dielectric constant and low loss tangent are highly regarded as substrates for modern high-speed electronics. In this work, we analyze the high-frequency dielectric properties of two types of composites based on polypropylene infused with high-dielectric-constant microparticles. Two types of fillers are used: commercial ceramics or titanium oxide ( TiO2) with different concentrations. The key observation...
-
Materiały stosowane do wytwarzania implantów kości
PublicationMateriały stosowane do wytwarzania implantów kostnych muszą być biokompatybilne, nietoksyczne, bioaktywne oraz wykazywać odpowiednie właściwości mechaniczne, takie jak wytrzymałość na ściskanie, na zginanie oraz sztywność i twardość. Gama stosowanych materiałów jest bardzo szeroka, obejmuje metale, polimery, ceramikę oraz ich kompozyty. Każdy z tych materiałów ma swoje mocne i słabe strony. Praca stanowi przegląd materiałów stosowanych...
-
Wpływ posuwu nagniatania na chropowatość powierzchni przedmiotów ze stali w stanie utwardzonym
PublicationPrzedstawiono wyniki badań eksperymentalnych procesu nagniatania stali twardej (62 HRC) narzędziem ceramicznym (kulką) z dociskiem hydrostatycznym. Analizowano wpływ posuwu nagniatania oraz parametrów poprzedzającej obróbki toczeniem na twardo na stan powierzchni opisanej wybranymi parametrami chropowatości.
-
THE POSSIBILITY OF USE OF LASER-MODIFIED Ti6Al4V ALLOY IN FRICTION PAIRS IN ENDOPROSTHESES
PublicationThe purpose of this paper is to show results of laser treatment at cryogenic conditions of the Ti6Al4V alloy used for orthopedic applications. That modification process ought to bring beneficial changes of microstructure and residual stresses in the surface layer. The paper presents the abrasive wear of the base and laser remelted material in association with ceramics Al2O3. Despite the surface cracking after laser treatment the...
-
Mixed ionic-electronic conductivity and structural properties of strontium-borate glass containing nanocrystallites of Bi2 VO5.5
PublicationSamples of strontium borate glass containing bismuth vanadate nanocrystallites were prepared. Nanocomposites containing up to 45mol% of the Bi2VO5.5 phase exhibit electrical properties closer to the strontium-borate glass than to the ferroelectric Bi2VO5.5 ceramic. The glass matrix still may contain some part of bismuth and vanadium ions even after crystallization process and there is too little of crystalline phase to observe...
-
Monosaccharides as Potential Chiral Probes for the Determination of the Absolute Configuration of Secondary Alcohols
PublicationHerein, a new method for the elucidation of the absolute configuration of chiral secondary alcohols is proposed. This method is an alternative for a widely used approach reported by Mosher and Dale and similar methods that are based on the 1H NMR shift (δ) changes of protons that are attached to the substituents of the oxymethine carbon atom. The presented method is not based on tracking the chemical shift changes and utilizes...
-
Determinants of Directionality and Efficiency of the ATP Synthase Fo Motor at Atomic Resolution
PublicationFo subcomplex of ATP synthase is a membrane-embedded rotary motor that converts proton motive force into mechanical energy. Despite a rapid increase in the number of high-resolution structures, the mechanism of tight coupling between proton transport and motion of the rotary c-ring remains elusive. Here, using extensive all-atom free energy simulations, we show how the motor’s directionality naturally arises from the interplay...
-
Investigation of electrocatalytic gas sensor properties in presence of chlorine
PublicationIn this paper performance of an electrocatalytic sensor in presence of chlorine is investigated. Presented studies concern sensor prepared in ceramic technology based on NASICON as a solid electrolyte with two round shaped platinum electrodes. Measurements in different temperatures have been performed in order to determine optimal sensor working temperature.
-
Degradation- and Thermal-Related Changes in Selected Electro-Optical Parameters of High-Power 270–280 nm LEDs
Publication -
Stanowisko do pomiaru termicznej stałej czasowej bolometrów
PublicationPrzedstawiono stanowisko umożliwiające pomiar termicznej stałej czasowej bolometrów. Stanowisko to składa się z dwóch układów pomiarowych połączonych z cyfrowym analizatorem sygnału i umożliwia pomiar stałej czasowej w zakresie od pojedynczych milisekund do kilku sekund. Omówiono budowę i działanie opracowanych układów i zaprezentowano wyniki pomiarów stałej czasowej bolometrów z niestechiometrycznych tlenków lantanowo-strontowo-żelazowych...
-
Compact broadband multi-way 1:6 power divider
PublicationThis paper introduces a design flow of a microstrip multi-way 1:6 power divider incorporating photonic bandgap (PBG) structures. Themethod proposed has enabled the achievement of considerable miniaturization (15%) together with transmission characteristics enhancement(141% bandwidth). Measured results show significant similarity to theoretical characteristics, which proves the attractiveness of presented design methodology.
-
Theoretical study of the energetics of the reactions of triplet dioxygen with hydroquinone, semiquinone, and their protonated forms: relation to the mechanism of superoxide generation in the respiratory chain = Badanie teoretyczne energii z energii reakcji dioksygenu potrójnego z wodorem, półkiną i ich formami protony: relacja z mechanizmem wytwarzania supertlenku w łańcuchu oddechowym
PublicationW pracy prezentujemy wyniki obliczeń kwantowych ab initio i półempirycznych energetyki reakcji redukcji jednoelektronowej tlenu trypletowego. Zaproponowaliśmy cztery możliwe mechanizmy redukcji i przeprowadziliśmy obliczenia kwantowe. Z obliczeń wynika, że najprawdopodobniejszy mechanizm reakcji wiedzie poprzez przeniesienie elektronu z anionu hydrochinonu po deprotonacji lub też z rodnika semichinonowego na tlen cząsteczkowy,...
-
Szerokopasmowy, zminiaturyzowany sprzęgacz gałęziowy ze zmodyfikowaną metalizacją paska i masy
PublicationZaprojektowano, wykonano i przebadano układ szerokopasmowego czterosekcyjnego sprzegacza gałęziowego. W celu poprawy charakterystyk transmisyjnych oraz redukcji wymiarów zaimplementowano w metalizacji masy struktury DGS (Defected Ground Structure), a w metalizacji paska komórki PBG (Photonic BandGap). Uzyskano znaczną (38%) miniaturyzację powierzchni układu przy zachowaniu szerokiego pasma pracy (47%).
-
Broadside Coupled Stripline with Double-Side UC-PBG Structure.
PublicationPoddano analizie symetryczną linię paskową z dwustronnie umieszczoną na płaszczyznach masy strukturą typu UC-PBG (uniplanar compact-photonic bandgap).Zaprojektowano, wykonano i pomierzono sprzęgacz wykonany w oparciu o tego typu prowadnicę. Miniaturyzacja wymiarów układu potwierdziła spodziewany efekt spowolnienia fali wywołany wprowadzeniem struktury UC-PBG.
-
Mn-Co spinel coatings on Crofer 22 APU by electrophoretic deposition: Up scaling, performance in SOFC stack at 850 °C and compositional modifications
PublicationCeramic coatings for metallic interconnects play a key role in limiting corrosion and chromium evaporation in solid oxide cells. This study presents the upscaling of the electrophoretic deposition (EPD) technique to process Mn-Co spinels on real-dimension Crofer 22 APU interconnects and the test in a SOFC stack. Area specific resistance of long-term test conducted for 5000 h at 850 °C demonstrated that two-steps sintering has a...
-
Assessment of Trace Metals Leaching During Rainfall Events from Building Rooftops with Different Types of Coverage – Case Study
PublicationRunoff water is an important medium transporting various types of pollution originating from the atmosphere and washed out from roofing materials. The study presents a quality assessment of runoff from different roofs in the context of trace metal concentrations. The analysed rooftops were covered with copper, tar paper and ceramic tile. The quality of the rain water collected at the same time satisfies the demands of the first...
-
Novel doubly perforated broadband microstrip branch-line couplers
PublicationTwo broadband compact doubly perforated hybrid couplers have been designed, manufactured, and measured. To improve frequency characteristics and to reduce circuit dimensions, two kinds of perforations have been introduced: the defected ground structures in the ground plane metallization and photonic bandgap cells in the strip metallization. Measurement results show essential miniaturization (~39% and ~36%) and enhancement of the...
-
Broadside coupled stripline with double-side UC-PBG structure
PublicationRozważono strukturę linii paskowych sprzężonych szerokim bokiem z periodycznie zaburzoną metalizacją masy typu UC-PBG (Uniplanar Compact - Photonic BandGap). W celu oceny przydatności struktury zaprojektowano, wykonano i przebadano sprzęgacz 3dB. Potwierdzono przewidywany efekt spowolnienia fali (slow wave effect), którego konsekwencją jest możliwość znacznej redukcji wymiarów układu.
-
CLAY MINERALS – MINERALOGY AND PHENOMENON OF CLAY SWELLING IN OIL & GAS INDUSTRY
PublicationAmong the minerals found in the earth's crust, clay minerals are of the widest interest. Due to the specific properties such as plasticity, absorbing and catalytic properties clay minerals are used in many industries (oil & gas, chemistry, pharmacy, refractory technology, ceramics etc.). In drilling, a phenomenon of swelling clays is frequently observed. It has an important impact on the cementing quality. During the last few decades...
-
Chapter 4. Electricity generation from glucose microbial fuel cell
PublicationThe microbial fuel cell was constructed to generate electricity with simultaneous digestion of a glucose fuel by a bacterial biofilm. The decomposition of glucose resulted in releasing of electrons to an anode and to production of some by-products, e.g. metane or organic acids. It was found that maximum electric power density strongly depended on the proton transport through the proton exchange membrane seperating the anolyte and...
-
Ocena stanu powierzchni kulek ceramicznych po nagniataniu tocznym stali hartowanej Cf53
PublicationW artykule przedstawiono wyniki z badań eksperymentalnych dotyczących przydatności kulek wykonanych z ceramiki technicznej, do nagniatania tocznego, narzędziami z dociskiem hydrostatycznym. W badaniach wykorzystano narzędzie umożliwiające wymianę kulek nagniatających. Badania wykonano poprzez nagniatanie wałków wykonanych ze stali Cf53 w stanie utwardzonym (zahartowanym). Wyniki badań obejmują charakterystyki stanu powierzchni...
-
Results of abrasive slurry dosage in lapping process
PublicationPrzedstawiono wyniki badań dawkowania zawiesiny ściernej w docieraniu powierzchni płaskich elementów ceramicznych. Analizowano wpływ dawkowania na podstawowe parametry chropowatości powierzchni ceramiki Al2O3 i Al2O3-ZrO2.
-
Charge Transport in High-Entropy Oxides
PublicationThis work presents the results of research on the transport properties of the high-entropy BaZr1/8Hf1/8Sn1/8Ti1/8Y1/8In1/8Sm1/8Yb1/8O3–x perovskite oxide with special focus on proton transport. The presented study is part of broader work in which we focus on multiple different chemical compositions with the cation number varying from 5 up to 12 (in B-sublattice). The presence of proton defects is analyzed with thermogravimetry,...
-
In Vitro Dissolution of Na-Ca-P-Oxynitrides
Publication: Sodium-calcium-phosphate based oxynitride glasses and glass-ceramics doped with Mg, Si, and Nb were studied in vitro in simulated body fluid (SBF) under static conditions. The release of ions and pH changes up to 7 days of immersion were investigated. The nitrogen incorporation into phosphate glass matrix was found to notably influence in vitro dissolution only of homogenous glasses. Increasing the nitrogen content in the samples...
-
Development of polyurethanes for bone repair
PublicationThe purpose of this paper is to review recent developments on polyurethanes aimed at the design, synthesis, modifications, and biological properties in the field of bone tissue engineering. Different polyurethane systems are presented and discussed in terms of biodegradation, biocompatibility and bioactivity. A comprehensive discussion is provided of the influence of hard to soft segments ratio, catalysts, stiffness and hydrophilicity...
-
Allergic reactions as a defense of the organism to the influence of implants components made of stainless steel
PublicationDue to the increasing number of cases of hypersensitivity caused by direct contact with metals, as well as the increasing demand for implants in humans all ages numerous studies on the effects of the impact of implant components are being carried out. The paper presents the phenomenon of etiology of allergy in general terms and in relation to the biomaterials used in medicine. There have been characterized in terms of impact on...
-
Allergic Reactions as a Defense of the Organism to the Influence of Implants Components Made of Stainless Steel
PublicationDue to the increasing number of cases of hypersensitivity caused by direct contact with metals, as well as the increasing demand for implants in humans all ages numerous studies on the effects of the impact of implant components are being carried out. The paper presents the phenomenon of etiology of allergy in general terms and in relation to the biomaterials used in medicine. There have been characterized in terms of impact on...
-
Novel Low-Loss Substrates for 5G Applications
PublicationThis paper presents a feasibility study of a new type of microwave low-loss dielectric substrates for 5G network applications. The new substrate materials are composites of polypropylene and high-dielectric-constant micro-ceramics. This combination is expected to form a very low-loss dielectric material at low fabrication cost. Two substrate samples with different dielectric properties are fabricated and their characteristics at...
-
Urządzenia elektrochemiczne wykorzystujące wysokotemperaturowe przewodniki protonowe
PublicationW artykule omówiono możliwe zastosowania wysokotemperaturowych przewodników protonowych. Omówiono zasadę działania różnych urządzeń elektrochemicznych opartych o elektrolit przewodzący protony.
-
A 3-dB coupler with UC-PBG structure
PublicationPrzedstawiono nową konstrukcję sprzęgacza z liniami paskowymi sprzężonymi szerokim bokiem oraz zmodyfikowaną warstwą metalizacji masy. Modyfikacja metalizacji polega na periodycznym wytrawieniu dwuwymiarowej struktury szczelin, nazywanej strukturą uniplanarnej zwartej przerwy fotonicznej (UC-PBG: Uniplanar Compact Photonic BandGap). Potwierdzono przewidywane wcześniej zjawisko spowolnienia fali oraz powiększenia wielkości sprzężenia...