Search
Filters
total: 196
filtered: 114
Search results for: POLYVINYLIDENE FLUORIDE
-
A New Microwave Ceramic – Polymer Composite with 0-3 Connectivity
PublicationGoal of the present research was to fabricate and study two-phase BiNbO4//PVDF composites with 0-3 connectivity. Such composite consists of there-dimensionally connected polymer matrix loaded with dielectric ceramic particles. In the present case BiNbO4 powder acted as an active phase (dispersed phase) whereas polyvinylidene fluoride (PVDF) acted as a non-active (passive) phase (matrix). BiNbO4//PVDF composites with the volume...
-
Enhanced electrochemical performance of SnS-PPy-carbon black composite with a locust bean gum as a binder as in anode in lithium-ion batteries
PublicationWater-soluble binders—locust bean gum (LBG) and carboxymethyl cellulose (CMC) were tested with the SnS anode modified by new conducting material polypyrrole—carbon black composite (PPyCB) and compared with the environmentally unfriendly widely used polyvinylidene fluoride (PVdF) as an organic binder. The electrochemical properties of tested electrodes were investigated by galvanostatic charging/discharging tests, cyclic voltammetry,...
-
Dielectric Properties of BiNbO<sub>4</sub>-Based Ceramic-Polymer Composites with 0-3 Connectivity
PublicationIn the present study two-phase BiNbO4//PVDF composites with 0-3 connectivity were studied by impedance spectroscopy within the frequency range Δν=100Hz-1MHz at room temperature. Polyvinylidene fluoride (PVDF) acted as a matrix whereas bismuth niobate (BiNbO4) powder acted as a dispersed phase. The volume fraction of the ceramic phase was cV=2, 4, 6, 8, 10, 16 and 20vol%. Analysis of the impedance data registered for composites...
-
The Effect of Sodium Tetrafluoroborate on the Properties of Conversion Coatings Formed on the AZ91D Magnesium Alloy by Plasma Electrolytic Oxidation
PublicationMagnesium and its alloys are widely used in many areas because of their light weight, excellent dimensional stability, and high strength-to-weight ratio. However, the material exhibits poor wear and corrosion resistance, which limits its use. Plasma electrolytic oxidation (PEO) is an effective surface modification method for producing ceramic oxide layers on Mg and their alloys. The influence of the additions of sodium tetrafluoroborate...
-
Semi-transparent ordered TiO2 nanostructures prepared by anodization of titanium thin films deposited onto the FTO substrate
PublicationIn a significant amount of cases, the highly ordered TiO2nanotube arrays grow through anodic oxidationof a titanium metal plate immersed in electrolyte containing fluoride ions. However, for some practicalapplications, e.g. solar cells or electrochromic windows, the semi-transparent TiO2formed directly onthe transparent, conductive substrate is very much desired. This work shows that high-quality Ti coatingcould be formed at room...
-
Preparation and evaluation of 1,3-alternate 25,27-bis-(pentafluorobenzyloxy)-26,28-bis-(3-propyloxy)-calix[4]arene-bonded silics gel high performance liquid chromatography stationary phase
PublicationA 1,3-alternate 25,27-bis-(pentafluorobenzyloxy)-26,28-bis-(3-propyloxy)-calix[4]arene-bonded silica gel stationary phase (CalixBzF10) was synthesized, structurally characterized, and used as a selector in liquid chromatography. The selectivity study of this phase was done by using fluorine-containing compounds (fluorobenzenes, fluoro-pyrimidine bases), as well as non-fluorinated analytes (non-steroidal anti-inflammatory drugs,...
-
Effect of AlF3 and KF addition on the structure and luminescent properties of P2O5 – K2O – Nb2O5 – Bi2O3 glasses doped with Eu3+
PublicationBased on the developed phosphate glasses P2O5–K2O–Bi2O3–Nb2O5 doped with Eu3+, the influence of AlF3 and KF on the structural and luminescent properties was investigated. For this purpose, three series of glasses containing from 5 to 15 mol% fluorides were synthesized. Two of the series included the KF additive, which was introduced in two ways - proportionally and disproportionately at the expense of the K2O share. The structural characterization...
-
Understanding the kinetics and atmospheric degradation mechanism of chlorotrifluoroethylene (CF2=CFCl) initiated by OH radicals
PublicationThe atmospheric degradation of chlorotrifluoroethylene (CTFE) by OH˙ was investigated using density functional theory (DFT). The potential energy surfaces were also defined in terms of single-point energies derived from the linked cluster CCSD(T) theory. With an energy barrier of −2.62 to −0.99 kcal mol−1 using the M06-2x method, the negative temperature dependence was determined. The OH˙ attack on Cα and Cβ atoms (labeled pathways...
-
General, Mild, and Metal-Free Functionalization of Indole and Its Derivatives Through Direct C3-Selenylation
PublicationA very mild method for the introduction of functionalized alkylselenyl group at C-3 position of the indole ring was developed. The proposed procedure consists of an electrophilic substitution of indole and its derivatives with bis(O,O-diisopropoxyphosphorothioyl) diselenide and subsequent cleavage of the P–Se bond with tetrabutylammonium fluoride in the presence of various electrophilic reagents. This method can be successfully...
-
From Structure to Luminescent Properties of B2O3-Bi2O3-SrF2 Glass and Glass-Ceramics Doped with Eu3+ Ions
PublicationGlass-ceramics with the composition B2O3 -Bi2O3 -SrF2 were synthesized by the conventional melt-quenching technique and subsequent crystallization of the parental glasses. The temperature at which the ceramization was carried out was selected based on differential scanning calorimetry (DSC) analysis. The structure of the studied materials and the formation of SrF2 nanocrystals were confirmed by the Fourier-transform infrared spectroscopy...
-
Anion recognition by n,n'-diarylalkanediamides
PublicationThe preparation of N,N'-diarylalkanediamides from respective aliphatic dicarboxylic acidesand 4-nitroaniline via microwave-promoted reactions is presented. The most positive effect of microwave irradiation was observed for N,N'-bis(4-nitrophenyl)butanediamide. Anion binding studies on the obtained diamides were carried out in DMSO and acetonitrile using UV-vis and 1H NMR spectroscopy. A mechanism for selective fluoride recognition...
-
Environmental degradation of titanium alloy in artificial saliva
PublicationThe titanium and its alloys are potentially prone to hydrogen embrittlement, including those proposed for dental implants. The research has been aimed to assess a susceptibility to environment-enhanced degradation of the Ti-13Zr-13Nb alloy in artificial saliva with or without hydrofluoric acid, subject or not to cathodic polarisation. The results have shown that even if artificial saliva is safe environment, both cathodic polarization...
-
ortho-Fluorobenzanilides and ortho-fluorothiobenzanilides: Molecular conformations and crystal packing
PublicationSeries of 2-fluoro and 2,6-difluorobenzanilides and their thiobenzanilide analogs have been synthesized to investigate the influence of the fluorine atom on their crystal structures and self-assembly in the crystal lattice. The X-ray analysis of the single crystal revealed that the synthesized molecules adopt a geometry being deflected from planarity. The deflection was investigated by analysis of dihedral angles between mean planes...
-
High-symmetry compact structures are preferred equilibrium configurations of Li n F n+1 − ( n = 2–5) superhalogen anions
Publication -
A metastable [(MgF3)2]2− dianion composed of two superhalogen anions
Publication -
A DFT computational study on the molecular mechanism of the nitro group migration in the product derived from 3-nitro-2-(trifluoromethyl)-2 H -chromene and 2-(1-phenylpropylidene)malononitrile
Publication -
Synthesis, physical–chemical properties and in vitro photodynamic activity against oral cancer cells of novel porphyrazines possessing fluoroalkylthio and dietherthio substituents
Publication -
Conductivity, structure, and thermodynamics of Y2Ti2O7–Y3NbO7 solid solutions
PublicationThe defect fluorite yttrium niobate Y3NbO7 and pyrochlore yttrium titanate Y2Ti2O7 solid solutions have been synthesized via a solid state synthesis route. The resulting stoichiometry of the oxides is Y2+xTi2−2xNbxO7, where x = 0 to x = 1. All of the samples were single-phase; however, for those with a predominant fluorite phase, a small amount of additional pyrochlore phase was detected. The volume of the solid solution unit cells...
-
Characterization of PVDF/Graphene Nanocomposite Membranes for Water Desalination with Enhanced Antifungal Activity
PublicationSeawater desalination is a worldwide concern for the sustainable production of drinking water. In this regard, membrane distillation (MD) has shown the potential for effective brine treatment. However, the lack of appropriate MD membranes limits its industrial expansion since they experience fouling and wetting issues. Therefore, hydrophobic membranes are promising candidates to successfully deal with such phenomena that are typical...
-
Enhanced cellulose extraction from agave plant (Agave americana Species) for synthesis of magnetic/cellulose nanocomposite for defluoridation of water
PublicationResearch on fluoride removal from water is currently focusing on the development of innovative materials for defluoridation water. The current study extracted and used enhanced cellulose from Agave americana species to synthesize a magnetic/cellulose nanocomposite for water defluoridation. Strong and light binary acids (H2SO4 and CH3COOH) were utilized to pretreat raw material to enhance cellulose extraction. Central composite...
-
Morphology and properties of nanotubular oxide layer on the Ti13Zr13Nb alloy
PublicationThe Ti13Zr13Nb alloy in solid and porous form was oxidised. The constant voltage 20 V, oxidation time 0.5 and 1 h, and 1 M H3PO4 (orthophosphoric acid) with addition of HF (hydrofluoric acid) as a test solution were applied. SEM (Scanning Electron Microscope) examinations of surface, EDS (Energy Dispersive X-ray Spectroscopy) chemical analysis, nanohardness and nano-scratch tests, and corrosion potentiokinetic tests at various...
-
The effect of morphology and crystalline structure of Mo/MoO3 layers on photocatalytic degradation of water organic pollutants
PublicationMolybdenum oxide layers were formed by anodization of the Mo metallic foil in a water/ethylene glycol-based electrolyte containing fluoride ions. The as-prepared, amorphous samples were annealed in air at different temperatures in a range from 100 �C to 700 �C. The crystal phase and morphology of anodized and annealed MoO3 layers were investigated using X-ray diffraction, Raman spectroscopy, and scanning electron microscopy. The...
-
Anion binding by p-aminoazobenzene-derived aromatic amides: spectroscopic and electrochemical studies
PublicationThe synthesis and complexing properties of p-aminoazobenzene-derived mono-, bis-, and trisamides were described. Ligands 3 and 4 bind anions, including fluorides, chlorides, bromides, acetates, benzoates, dihydrogen phosphates, hydrogen sulfates, and p-toluenesulfonates, in chloroform forming 1 : 1 complexes. The highest value of stability constant was evaluated for the 4-F− complex (log K = 5.63 ± 0.21). On the basis of 1H NMR,...
-
The optimization of CuxO microwires synthesis for improvement in photoelectrochemical performance
PublicationOne of the most important challenges in the fabrication of CuxO microstructures via the electrochemical method is formation of long, regular and well-packed microwires with good adhesion on the Cu substrate and to achieve better photoelectrochemical properties, which can be potentially applied in solar-driven water splitting and CO2 conversion to light hydrocarbons. In this paper, Cu2O photoelectrode has been fabricated by direct...
-
Influence of titanium layer on counter electrode on electrical parameters of DSSC
PublicationIn this paper the influence of the Ti layer thickness at counter-electrode on electrical parameters of DSSCs was examined. The transparent conductive oxide – less (TCO-less) counter electrodes (CE) with titanium layers and platinum as catalyst on Bk7 glass were prepared. Thin metallic films were deposited by means of magnetron sputtering (titanium) and Pulsed Laser Deposition (platinum). The counter electrode with Pt layer on Fluorine...
-
Solvothermal growth of {0 0 1} exposed anatase nanosheets and their ability to mineralize organic pollutants. The effect of alcohol type and content on the nucleation and growth of TiO2 nanostructures
PublicationHerein, the series of {0 0 1} exposed anatase nanosheets from HF-assisted solvothermal growth synthesis were obtained. The two-dimensional TiO2 were characterized, including both bulk (XRD, DR-UV–Vis, Mott-Schottky) and surface characteristics (N2 sorption, XPS, SEM) with experimental results compiled with Density Functional Theory (DFT) calculations. The effect of alcohol amount and type was studied, demonstrating the crucial...
-
New potent STS inhibitors based on fluorinated 4-(1-phenyl-1H-[1,2,3]triazol-4-yl)-phenyl sulfamates
PublicationA series of fluorinated analogs based on the frameworks of 4-(1- phenyl-1H-[1,2,3]triazol-4-yl)-phenyl sulfamates have been synthesized as steroid sulfatase (STS) inhibitors. The design of chemical structures of new potential STS inhibitors was supported by molecular docking techniques to identify potential interactions between inhibitors and amino acid residues located in the STS active site. The STS inhibitory potency was evaluated...
-
Evaluation of the influence of grapevine growing conditions on wine quality
PublicationScientists are increasingly interested in the viticulture concept of terroir, which states that unique properties of wine are strictly related to the environmental conditions under which grapes are cultivated. The aim of the research was to compare the parameters characterizing wines produced in Poland, such as pH, conductivity, total organic carbon (TOC), and concentration of anions (F−, Cl−, NO2−, NO3−, PO43−, SO42−). It was...
-
KTaO3 a perovskite for water and air treatment
PublicationPerovskites are inorganic compounds that exhibit dielectric properties. These minerals belong to the crystal ceramics family. These compounds are described by the formula: ABX3 where, A and B are 2, 3 or 4 valuable metal ions, and X is an ion of oxygen or fluorine. An example of perovskite is the compound KTaO3. There are many methods for producing KTaO3, but the hydrothermal method is most commonly used. Perovskites can be characterized...
-
Peroxymonosulfate-assisted photocatalytic degradation of artificial sweeteners in water
PublicationIn the present study, peroxymonosulfate (PMS) activation was proposed for efficient photocatalytic degradation of aspartame, acesulfame, saccharin, and cyclamate - artificial sweeteners frequently present in wastewaters and surface waters worldwide. The TiO2 nanosheets with exposed {0 0 1} facets were synthesised using the fluorine-free lyophilisation technique as a green concept for the synthesis and used for the photodegradation...
-
A white phosphor based on oxyfluoride nano-glass-ceramics co-doped with Eu3+ and Tb3+: Energy transfer study
PublicationStrontium fluoride nanocrystals doped separately with Ln3+ = Eu3+ or Tb3+ ions (95SrF2·5LnF2), as well as co-doped with both the ions (95SrF2·Eu4Tb) were synthesized for comparison. Then, glass-ceramics consisting of the mono-doped or di-doped SrF2 nanocrystals incorporated into amorphous silica (90SiO2·9.5SrF2·0.5Ln or 90SiO2·9.5SrF2·0.1EuF3·0.4Tb) were prepared by sol-gel procedure. The studied materials were characterized by...
-
Extracellular proteolytic activity of Deinococcus geothermalis
PublicationProduction of extracellular protease by extremophilic bacteria Deinococcus geothermalis cultivated in liquid media containing 0.1% (w/v) of peptone K, 0.1% yeast extract and 0.2% marine salt reached a maximum in 14 h of the cell growth at 45°C and pH 8.0. The enzyme was purified by a two-step procedure using fractionation by a graded ammonium sulphate precipitation technique and gel filtration on Sephadex G-100 column. Protease...
-
Groundwater Quality in the Gdansk Aquifer System
PublicationThe Gdańsk hydrogeological system consists of three main aquifers: Cretaceous, Paleogene-Neogene and Pleistocene. Chemical composition of groundwater varies between water-bearing beds, although water from Pleistocene and Paleogene-Neogene aquifers shows much similarities. The dominant hydrochemical groundwater types is HCO3-Ca. This type is characteristic for Pleistocene deposits in the Kashubian Lake District where natural chemical...
-
Synthesis, structure and luminescence properties of borate-bismuth glasses and glass-ceramics doped with rare earth ions
PublicationIn a doctoral dissertation, new borate-bismuth glasses and glass-ceramics containing AlF3 and SrF2 were examined as potential hosts for RE3+ ions. Experimental studies were conducted to determine optimal conditions for synthesizing transparent borate-bismuth glasses and glass ceramics, with a focus on analyzing their structure and luminescence properties. The introduction of AlF3 into the glass matrix led to an increase in the...
-
Unraveling a novel microwave strategy to fabricate exposed {001}/{101} facets anatase nanocrystals: Potential for use to the elimination of environmentally toxic metronidazole waste
PublicationThis study present a novel microwave strategy to fabricate highly active anatase particles, exposing {101} and {001} facets. Microwave treatment time was shown to determine the growth of crystals in a certain direction. To the best of our knowledge, it is the first report revealing that the contact time of TiO2 crystals with fluorine ions during the microwave process affects the formed morphology, in particular exposed facets ratio....
-
Antibacterial properties of laser-encapsulated titanium oxide nanotubes decorated with nanosilver and covered with chitosan/Eudragit polymers
PublicationTo provide antibacterial properties, the titanium samples were subjected to electrochemical oxidation in the fluoride-containing diethylene glycol-based electrolyte to create a titanium oxide nanotubular surface. Afterward, the surface was covered by sputtering with silver 5 nm film, and the tops of the nanotubes were capped using laser treatment, resulting in an appearance of silver nanoparticles (AgNPs) of around 30 nm in diameter...
-
Study of Cloud Water Samples Collected over Northern Poland
PublicationThe paper gives the results of the first studies on the chemistry of cloud water collected during 3 mo (Aug.–Oct. 2010) in the free atmosphere over the area to the south of the Tri-City (Gdansk-Sopot-Gdynia) conurbation on the Gulf of Gdansk, Poland. Taken from cumulus, stratus, and stratocumulus clouds by means of an aircraft-mounted collector, the water samples were analyzed for the following contaminants: anions (chlorides,...
-
High-temperature properties of titanium-substituted yttrium niobate
Publicationhe defect fluorite titanium-doped yttrium niobate samples Y3Nb1−xTixO7−δ have been synthesized and investigated by the means of high-temperature X-ray diffraction, dilatometry, and thermogravimetry. Thermal expansion coefficients (TECs) as well as chemical expansion coefficients for material with 5, 10, and 15 mol% of titanium were determined. All investigated samples exhibit chemical contraction caused by Ti doping. The values...
-
Thin layer of ordered boron-doped TiO2 nanotubes fabricated in a novel type of electrolyte and characterized by remarkably improved photoactivity
PublicationThis paper reports a novel method of boron doped titania nanotube arrays preparation by electrochemical anodization in electrolyte containing boron precursor – boron trifluoride diethyl etherate (BF3 C4H10O), simultaneously acting as an anodizing agent. A pure, ordered TiO2 nanotubes array, as a reference sample, was also prepared in solution containing a standard etching compound: ammonium fluoride. The doped and pure titania...
-
Nanostructuring of thin Au films deposited on ordered Ti templates for applications in SERS
PublicationIn this work the results on thermal nanostructuring of the Au films on Ti templates as well as morphology and optical properties of the obtained structures are reported. The bimetal nanostructures are fabricated in a multi-step process. First, the titania nanotubes are produced on the surface of Ti foil by anodization in an ethylene glycol-water solution containing fluoride ions. This is followed by chemical etching in oxalic acid...
-
A Flexible Nafion Coated Enzyme‐free Glucose Sensor Based on Au‐dimpled Ti Structures
PublicationThe detection of glucose at low concentrations using electrochemical sensors is of great importance due to the possibility of using different human body fluids than blood, such as e.g. urine, saliva, sweat or tears. The interest behind those biofluids is related to their utility in non-invasive sugar determination. In this work, we present flexible, fully biocompatible electrode material based on Au nanoparticles immobilized onto...
-
Design and synthesis of TiO2/Ti3C2 composites for highly efficient photocatalytic removal of acetaminophen: The relationships between synthesis parameters, physicochemical properties, and photocatalytic activity
PublicationIn this study, we report the potential of TiO2/Ti3C2 composite fabricated by oxidation of MXene for degradation of persistent organic pollutants. The effect of the synthesis conditions (time, temperature, and reaction environment) on the morphology, physicochemical properties, and photocatalytic activity was investigated. It was found that acetaminophen degradation was positively correlated with TiO2 content in the composite structure. Furthermore,...
-
Application of surface active amino acid ionic liquids as phase-transfer catalyst
PublicationFive structurally related morpholinium derived ionic liquids containing N-acetyl-glycinate anion were synthesized and their thermal stability, surface properties and activity as phase transfer catalysts investigated. The thermal properties were studied by differential scanning calorimetry, while the adsorption at the air/water interface and micellization behavior was analyzed by surface tension measurements, conductometry and isothermal...
-
Recovery and re-use of photovoltaic solar cells from crystalline silicon
PublicationCrystalline silicon-type PV modules consist, in order of mass, of glass, an aluminium frame, an EVA coating, solar cells, a terminal box, back film and tapping screws. From the economic point of view, pure silicon, recoverable from spent cells, is the most important material owing to its cost and shortage. For crystalline, silicon-based PV cells, the following chemical treatments were performed: removal of the metal coating, followed...
-
Hydrogen evolution reaction catalyzed by Co-based metal-organic frameworks and their derivatives
PublicationIn this study, Co-bearing Metal-Organic Frameworks (MOFs) are grown via a facile solvothermal process on the surface of two kinds of conductive substrates – titanium dioxide nanotubes (TiO2NT) and fluorine-doped tin oxide (FTO) glass and tested as electrodes in the electrochemical hydrogen evolution reaction (HER). The materials derived from three organic linkers - terephthalic acid (Co-BDC), 2-aminoterephthalic acid (Co-BDCNH2),...
-
Unexpected Z/E isomerism of N-methyl-O-phosphothioyl benzohydroxamic acids, their oxyphilic reactivity and inertness to amines
PublicationThiophosphinoylation of N-methyl p-substituted benzohydroxamic acids using disulfanes (method A) or diphenylphosphinothioyl chloride (method B) provides only one conformer of the respective O-phosphothioyl derivative (Xray and NMR analysis). Undergoing the P-transamidoxylation reaction is an evidence of the reversibility of thiophosphinoylation. Only those products containing strong EWG substituents in the aroyl residue or bulky...
-
Enhanced Mechanical and Electromechanical Properties of Compositionally Complex Zirconia Zr1–x(Gd1/5Pr1/5Nd1/5Sm1/5Y1/5)xO2−δ Ceramics
PublicationCompositionally complex oxides (CCOs) or high-entropy oxides (HEOs) are new multi-element oxides with unexplored physical and functional properties. In this work, we report fluorite structure derived compositionally complex zirconia with composition Zr1- x(Gd1/5Pr1/5Nd1/5Sm1/5Y1/5)xO2-δ (x = 0.1 and 0.2) synthesized in solid-state reaction route and sintered via hot pressing at 1350 °C. We explore the evolution of these oxides'...
-
Pochodne kwasu neopentylidenofosforoditiowego jako substraty do syntezy ugrupowania trisulfidowego
PublicationBadania przeprowadzone w Katedrze Chemii Organicznej Wydziału Chemicznego Politechniki Gdańskiej na przestrzeni ostatnich kilku lat, pokazały wszechstronność pochodnych kwasu neopentylidenofosforoditiowego [32] w syntezie symetrycznie i niesymetrycznie podstawionego ugrupowania disulfidowego. Wyniki powyższych badań doprowadziły do opracowania nowej strategii syntetycznej, umożliwiającej otrzymywanie...
-
Photoresponsive Amide-Based Derivatives of Azobenzene-4,4′-Dicarboxylic Acid—Experimental and Theoretical Studies
PublicationAzobenzene derivatives are one of the most important molecular switches for biological and material science applications. Although these systems represent a well-known group of compounds, there remains a need to identify the factors influencing their photochemical properties in order to design azobenzene-based technologies in a rational way. In this contribution, we describe the synthesis and characterization of two novel amides...
-
Genotoxicity of selected pharmaceuticals, their binary mixtures, and varying environmental conditions – study with human adenocarcinoma cancer HT29 cell line
PublicationPharmaceutical residues are present in the environment in mixtures and their adverse effects may also result from interactions that occur between compounds. Studies presented in this work focus on genotoxicity of pharmaceuticals from different therapeutic groups in mixtures and in individual solutions impacted with different environmental conditions assessed using comet assay (alkaline approach). Binary mixtures of pharmaceuticals...