Filters
total: 3546
filtered: 2763
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: nanohydroxyapatite coating
-
Biological and mechanical research of titanium implants covered with bactericidal coating
PublicationThe paper concerns the biological and mechanical properties of titanium implants with an antibacterial coating. The Ti13Zr13Nb alloy samples were coated with hydroxyapatite (HAp) coatings using the electrophoretic deposition technique (EPD). Subsequently, the surface of the samples was modified with silver, copper, and nickel nanoparticles by the immersion method. Different titanium sample types (i.e. HAp-only and nanometals-enriched...
-
Modified Manganese Phosphate Conversion Coating on Low-Carbon Steel
PublicationConversion coatings are one of the primary types of galvanic coatings used to protect steel structures against corrosion. They are created through chemical reactions between the metal surface and the environment of the phosphating. This paper investigates the impact that the addition of new metal cations to the phosphating reaction environment has on the quality of the final coating. So far, standard phosphate coatings have contained...
-
Corrosion degradation of spacers – examination of changes in bone cement coating.
PublicationSpacer is a special implant used at the time of infection after endoprosthetic surgery. It consists of a metal core and bone cement coating with an antibiotic. In the human body spacers are exposed to degradation processes. This paper looks at the effect of corrosion on spacers. Electrochemical corrosion tests were performer on titanium pins with bone cement coating in two solutions: Ringer’s solution and artificial...
-
Identification and localization of organic coating degradation onset by impedance imaging
Publication -
Assessment of organic coating degradation via local impedance imaging
PublicationThe paper presents a new approach to organic coating condition evaluation at micrometer scale using localized impedance measurements. It is based on atomic force microscopy (AFM) in contact mode. Impedance is measured between conductive AFM tip and metal substrate covered with organic coating. A single-frequency voltage perturbation signal is applied between the electrodes and current response signal is registered. As the tip is...
-
Selection of Organic Coating Systems for Corrosion Protection of Industrial Equipment
PublicationThe most important element of corrosion protection in industrial conditions is the protective coating system. However, selecting the right coating can often be a real problem due to the sheer number of coating manufacturers and their products on the market. A quantitative approach based on the data mining technique used to analyze the obtained multi-site exposure data has been proposed. This was demonstrated by the example of the...
-
Damage Development on the Surface of Nickel Coating in the Initial Period of Erosion
PublicationThe common occurrence of the phenomenon of cavitation in many industries and the multitude of factors affecting the resistance to cavitation erosion of used materials contribute to the search for methods and appropriate parameters of coating application that are able to minimize the effects of erosion. To determine the validity of the developed application parameters and the method used, cavitation studies and microscopic observations...
-
Measurements of the optical and thermal properties of the 2D black phosphorus coating
PublicationBlack phosphorus is a 2D material, which properties are still being discovered. In this paper, the sensitivity to the temperature of a few-layer black phosphorus coating deposited, on the surface of a microsphere-based fiber-optic sensor, by a dip-coating method is presented. The coating was investigated after 2, 3, and 5 deposition cycles and during temperature growth from 50 °C to 300 °C in an interferometric setup. The intensity...
-
Conducting coatings as anodes in cathodic protection
PublicationPrzedstawiono wyniki pomiarów elektrochemicznych powłok przewodzących opartych o mieszaninę pigmentów węglowych osadzonych w matrycy polimerowej. Wyznaczono parametry powłok przewodzących w oparciu o metodę elektrochemicznej spektroskopii impedancyjnej. Parametry elektryczne i elektrochemiczne były wyznaczane jednocześnie, w czasie długotrwałej anodowej polaryzacji badanych powłok. Stwierdzono, że badane powłoki mogą być używane...
-
Local impedance spectra of organic coatings
Publication -
WETTABILITY OF HYBRID CHITOSAN/PHOSPHOLIPID COATINGS
Publication -
Advancements in Diamond-Like Carbon Coatings
PublicationAn essential resource for engineers and scientists in the coatings field, providing an in-depth examination of current and advanced technologies for industrially oriented nanoceramic and nanocomposite coatings
-
Cavitation erosion degradation of Belzona® coatings
PublicationIn hydrocarbon and maritime industry there is a constant need of materials and coatings withstanding severe conditions. One of adverse phenomena present there is cavitation erosion. The paper presents evaluation of cavitation resistance of three different steel coatings. Belzona 2141 (ACR-Fluid Elastormer), 1321 (Ceramic S-Steal) and 5831 (ST-Barrier) were deployed on P110 steel and subjected to ultrasound cavitation in distilled...
-
Local impedance spectra of organic coatings
PublicationPublikacja przedstawia nowe podejście do lokalnych spektroskopowych pomiarów impedancyjnych powłok organicznych, oparte o mikroskop sił atomowych pracujący w trybie kontaktowym. Pomiędzy nieporuszającą się igłę mikroskopu i podłoże metalowe pokryte powłoką epoksydową przyłożono serię sinusoidalnych napięciowych sygnałów pobudzenia w zadanym zakresie częstotliwości. W ten sposób zarejestrowano lokalne widma w trybie "frequency by...
-
Biopsy needles coated with the antimicrobial coatings
PublicationDrug delivery systems are used to achieve higher therapeutic effects of medicaments in a specific diseased site with minimal toxicological effect. The used of biopolymers in drug delivery systems ensure the biocompatibility, biodegradability and low immunogenicity. Drug delivery systems enhance the drug delivery actively and can be used in different diseases. In this study, two types of polymer coatings were prepared and were...
-
Analysis of Cutting Force and Power Under the Conditions of Minimized Cooling in the Process of Turning AISI-1045 Steel with the Use of the Parameter Space Investigation Method
Publication -
Influence of polyaniline primer on the corrosion properties of St3S steel - coating system
PublicationPraca przedstawia wyniki badań wpływu podkładu z polianiliny osadzonej elektrochemicznie na właściwości antykorozyjne powłoki epoksydowej na stali niskowęglowej St3S. Wykonano badania próbek nieuszkodzonych, a także próbek ze sztucznym defektem powłoki. Próbki były eksponowane na środowisko korozyjne przez 63 dni i były sukcesywnie badane za pomocą elektrochemicznej spektroskopii impedancyjnej. Postępy korozji były również oceniane...
-
Quantification of interlayer adhesion in protective coating systems using impedance spectroscopy
PublicationNowoczesne systemy powłokowe stosowane w praktyce są wielowarstwowe. Potencjalnie słabymi obszarami z punktu widzenia właściwości ochronnych są obszary międzywarstwowe. Osiągnięcie odpowiedniej przyczepności pomiędzy warstwami pozwala na polepszenie zdolności ochronnych całego zestawu. Tradycyjne metody pomiaru adhezji międzywarstwowej są destrukcyjne. Zaproponowano nową metodę oceny przyczepności międzywarstwowej przy użyciu...
-
Impedance-based sensing of the interlayer adhesion loss in organic coating systems.
PublicationZmienne parametry środowiska takie jak: temperatura,wilgotność i promieniowanie UV powodują degradację własności ochronnych powłok organicznych. Stosując sensor w postaci elektrod wykonanych z prądoprzewodzącego tuszu umieszczonych pomiędzy warstwami zestawu oraz technikę spektroskopii impedancyjnej stwierdzono możliwość monitorowania utraty adhezji międzywarstwowej.
-
Characteristics of silver-dopped carbon nanotube coating destined for medical applications
PublicationCarbon nanotubes are materials demonstrating outstanding mechanical, chemical, and physical properties and are considered coatings of titanium implants. The present research is aimed to characterize the microstructure and properties of the multi-wall carbon nanotubes (MWCNTs) layer decorated with silver nanoparticles (Ag NPs) on the Ti13Nb13Zr alloy destined for long-term implants. The electrophoretic deposition of coatings...
-
Application of impedance imaging to evaluation of organic coating degradation at a local scale
Publication -
Impedance-based sensing of the interlayer adhesion loss in organic coating systems
Publication -
Effect of interconnect coating procedure on solid oxide fuel cell performance
PublicationChromium (Cr) species vaporizing from chromia-forming alloy interconnects is known as a source of degradation in solid oxide fuel cell (SOFC) stacks called “cathode poisoning”. (Mn,Co)3O4 spinel coatings offer good protection against Cr evaporation during operation. In this study, Crofer 22 APU steel interconnects were electrophoretically deposited in different mediums to obtain high packing of green coating layer. The optimized...
-
Novel application of dynamic electrochemical impedance monitoring to a cataphoretic coating process
PublicationThe paper presents a novel method of on-line impedance monitoring of cataphoretic coating application process. Utilization of dynamic electrochemical impedance spectroscopy (DEIS) overcame the fundamental problem connected with non-stationarity of the aforementioned coating deposition process, which eliminates classical impedance spectroscopy technique from a real-time description of cataphoresis. The paper illustrates selected examples...
-
In Vitro Biological Characterization of Silver-Doped Anodic Oxide Coating on Titanium
PublicationDespite the high biocompatibility and clinical effectiveness of Ti-based implants, surface functionalization (with complex osteointegrative/antibacterial strategies) is still required. To enhance the dental implant surface and to provide additional osteoinductive and antibacterial properties, plasma electrolytic oxidation of a pure Ti was performed using a nitrilotriacetic acid (NTA)-based Ag nanoparticles (AgNP)-loaded calcium–phosphate...
-
On the peculiarities of anti-plane surface waves propagation for media with microstructured coating
PublicationWe discuss new type of surface waves which exist in elastic media with surface energy. Here we present the model of a coating made of polymeric brush. From the physical point of view the considered model of surface elasticity describes a highly anisotropic surface coating. Here the surface energy model could be treated as 2D reduced strain gradient continuum as surface strain energy depends on few second spatial derivatives of...
-
Effect of Coating Material Properties on Tilting-pad Thrust Bearing Performance
PublicationPolymer lined tilting-pad bearings demonstrate many advantages over traditional bearing systems. Bearings with a polymer layer in comparison with a babbitted layer show, for example: lower value of friction coefficient (important during start/stops), higher fatigue strength of the coating, better distribution of the load on individual pads due to lower elasticity of the polymers, wider range of operational temperatures or the ability...
-
Structure of sol-gel derived Nb2O5 films for active coating devices
PublicationW artykule przedstawiono wyniki badań struktury cienkich warstw nb2o5 otrzymywanych metodą zol-żel. wytworzone warstwy charakteryzowano pod kątem zastosowania jako materiałów na aktywne pokrycia fotoniczne.
-
Aplication of impedance imaging to evaluation of organic coating degradation at a local scale
PublicationZaproponowano nowe podejście do oceny lokalnych właściwości elektrycznych powłok organicznych. Wykorzystuje ono mikroskop sił atomowych pracujący w trybie kontaktowym. Pomiędzy igłę mikroskopu i podłoże metalowe pokryte powłoką przykładany jest sinusoidalny napięciowy sygnał pobudzenia o zadanej częstotliwości i mierzony jest prądowy sygnał odpowiedzi. Zalety tego podejścia zostały zaprezentowane na przykładzie powłoki akrylowej...
-
Ceramic dispersion effect on composite coating properties after plastic working
PublicationW pracy określono wpływ fazy dyspersyjnej Al2O3 na wybrane potencjalne właściwości powłok kompozytowych o osnowie niklowej. Powłoki Ni-Al-Al2O3 zostały nałożone na próbki stalowe przy użyciu technologii poddźwiękowego płomieniowego natryskiwania cieplnego. Następnie poddane zostały obróbce plastycznej na zimno i na gorąco poprzez walcowanie, a także prasowania na zimno na prasie hydraulicznej. Omówiono wpływ obróbki plastycznej...
-
FEM approach to estimate the behaviour of biocomposite metal-surface coating system
PublicationA three dimensional (3D) model of biocomposite metal-surface coating system, which is influenced byknown external forces, is proposed. This model consists of the metallic substrate (Ti6Al4V) and thehydroxyapatite (HA) coating. Using FEM (finite element method), strain-stress maps of model weregenerated for investigating relations between the extreme stress of HA coating and the magnitude ofexternal force and the thickness of the...
-
Effect of electrode waterproof coating on quality of underwater wet welded joints
PublicationIn this paper, the effects of different hydrophobic coatings on the surface of covered electrodes on the quality of wet welded carbon steel joints were discussed. Commonly available hydrophobic substances used in industrial applications were selected for the research. The aim of using waterproof coatings was to check the possibility to decreasing the susceptibility of highstrength low-alloy S460N steel to cold cracking. During...
-
Bidirectional voting and continous voting concepts as possible use of Internet in democratic voting process
PublicationDemocracies need elections for choosing their authorities and governments.This process has many factors that shape today's procedures. However, the Internet is a medium that may change possibilities and elections. The main issue is concern on how changes may influence the whole democratic process. this paper shows two possible ideas - that of bidirectional voting and continous voting., and considers possible reasons for introducing...
-
Nucleate pool boiling on porous metallic coatings
PublicationPrzedstawiono wyniki systematycznych badań eksperymentalnych przejmowania ciepła podczas wrzenia pęcherzykowego wody destylowanej w stanie nasycenia od płaskich i cylindrycznych powierzchni o specjalnie przygotowanej powierzchni: gładkiej, chropowatej oraz pokrytej warstwą porowatą.
-
Effect of SiC on the corrosion behaviour of chromium coatings
PublicationWarstwy kompozytowe Cr-SiC osadzono z kąpieli zawierającej Cr(VI) oraz zielony proszek SiC. Zawartość SiC w warstwie chromowej wynosiła od 0,1-0,9% wag. Badania XPS wykazały iż SiC pokrywała warstwa SiO2, która powstała w wyniku utleniania SiC za pomocą Cr(VI). Przeprowadzono badania potencjodynamiczne i badania za pomocą spektroskopii impedancyjnej w celu określenia właściwości korozyjnych warstw Cr-SiC w środowisku kwaśnym....
-
Impedance evaluation of coatings from biobased material
PublicationThe authors propose a modification of sodium caseinate edible coating for foodstuff protection. The aim was to improve the film’s barrier properties. It was achieved by the addition of propolis, which is a natural, environmentally friendly product known from its intrinsic sealing action. In the next step, propolis-admixed sodium caseinate films were exposed to elevated temperature for 10 min. This approach was meant to improve...
-
AFM-assisted investigation of conformal coatings in electronics
PublicationPurpose – This paper aims to presents a new method of investigation of local properties of conformal coatings utilized in microelectronics. Design/methodology/approach – It is based on atomic force microscopy (AFM) technique supplemented with the ability of local electrical measurements, which apart from topography acquisition allows recording of local impedance spectra, impedance imaging and dc current mapping. Potentialities...
-
Electrical properties of polymer coatings modified with nanoadditives
PublicationW pracy przedstawiono właściwości elektryczne (antystatyczne, rezystancję powierzchniową) polimerowych powłok. Pokazano wpływ różnych domieszek na czasy rozładowania się warstwy oraz na jej rezystancję powierzchniową.
-
Hydroxyapatite coatings on porous ti and ti alloys
PublicationDeposition of hydroxyapatite coating on porous Ti and Ti alloys with electrochemical and biomimetic deposition approach is presented. The enhancement of phosphates deposition by well oriented and uniform titanium oxide nanotube array on the surface of titanium substrate is discussed.
-
Effect of ZrO2 on corrosion behaviour of chromium coatings
PublicationW celu zbadania wpływu cząstek ZrO2 na zachowania korozyjne powłok chromowych pokryto stal chromem z elektrolitów Cr(VI) z dodatkiem i bez ZrO2. Właściwości korozyjne osadzonych warstw zbadano w elektrolicie 0,01 mol L(-1) kwasu siarkowego plus 0,5 mol L(-1) siarczanu sodu za pomocą metody spektroskopii impedancyjnej i woltamperometrii cyklicznej. Zaproponowano elektryczny obwód zastępczy dla procesu korozji i wyznaczono pęd korozji....
-
Protective coatings for stainless steel for SOFC applications
PublicationW pracy przedstawiono badania związane z warstwami antykorozyjnymi stali nierdzewnych stosowanych w tlenkowych ogniwach paliwowych. Warstwy przygotowana z użyciem prekursorów polimerowych na bazie Y i Co. Użyta stal to Crofer 22 APU.
-
A method for the tribological testing of thin, hard coatings
Publication -
Fabrication methods of smart composite coatings - review
PublicationPostoperative bacterial infections are one of the main reasons for unsuccessful implantation of long-term implants. The development of bacterial infection requires antibiotic therapy, in extreme cases a reimplantation procedure is necessary. In order to provide materials for implants with antibacterial properties, they are subjected to modifications to create a coating that will release the drug substance, when the inflammation...
-
RESEARCH ON ORGANIC COATINGS DESIGNED FOR UNDERWATER APPLICATIONS
PublicationUnderwater steel structures require periodic maintenance. In the case of vessels, anti-corrosion works are carried out in the shipyard, where very good conditions for applying organic protective coatings can be provided. Very good surface preparation can be obtained by the use of abrasive blasting. The well-prepared metal surface is free from impurities (particularly inorganic salts). Suitable conditions for the application and...
-
Integration of antifouling properties into epoxy coatings: a review
Publicationhe need for nontoxic antifouling coatings has encouraged material scientists to develop a class of organic coatings for diverse applications. As a versatile thermosetting resin and well known for coating application, antifouling characteristics have been integrated into epoxy along with anticorrosion and adhesive functions. Accordingly, both micro- and macro-biofoulings have been successfully controlled by using epoxy-based antifouling...
-
Effects of Surface Pretreatment of Titanium Substrates on Properties of Electrophoretically Deposited Biopolymer Chitosan/Eudragit E 100 Coatings
PublicationThe preparation of the metal surface before coating application is fundamental in determining the properties of the coatings, particularly the roughness, adhesion, and corrosion resistance. In this work, chitosan/Eudragit E 100 (chit/EE100) were fabricated by electrophoretic deposition (EPD) and both their microstructure and properties were investigated. The present research is aimed at characterizing the effects of the surface...
-
Nanotubular oxide layers and hydroxyapatite coatings on ‘Ti–13Zr–13Nb’ alloy
PublicationThe presented research was aimed to determine the mechanical properties of the nanotubular oxide layer covered with hydroxyapatite coating. The Ti–13Zr–13Nb alloy was oxidised in 1M phosphoric acid with an addition of 0?5% HF for HF solution at 20 V voltage. The electrochemically assisted deposition of hydroxyapatite was performed at cyclic polarisation in NH4H2PO4 and CaCl2 solution at 80uC. The mechanical properties were determined...
-
The effect of improved cutting conditions of the circular saw blade on precision of cutting
PublicationW pracy przedstawiono analizę i wyniki badań doświadczalnych dokładności przecinania na dwuwrzecionowej pilarce tarczowej. W warunkach przemysłowych badano piły starej (typ "Multix") i nowej konstrukcji podczas przecinania pryzm ze zmrożonego drewna brzozowego. Ponadto, określono wpływ kinematyki układu przecinania na uzyskiwaną dokładność przecinania.
-
Ecological floating dock
PublicationZaprezentowano efekt końcowy projektu europejskiego grupy EUREKA pn. ''Przyjazne środowiskowo doki pływające''. Przedstawiono konsorcjum realizacyjne projektu, scharakteryzowano zagrożenia ekologiczne, wskazano najważniejsze uregulowania prawne oraz scharakteryzowano projekt proekologicznego doku pływającego SINE 212CD i koncepcję przebudowy doku istniejącego SINE 126 CD. Artykuł zawiera też kompletną bibliografię prac wykonanych...
-
Floating caissons of Gdynia
PublicationArtykuł poświecono projektom i wykonawstwu zelbetowych skrzyń pływających stosowanych jako elementy konstrukcyjne nabrzeży i falochronów w porcie gdyńskim.