Filters
total: 8431
-
Catalog
- Publications 6527 available results
- Journals 48 available results
- Conferences 5 available results
- Publishing Houses 1 available results
- People 150 available results
- Inventions 3 available results
- Projects 6 available results
- Laboratories 3 available results
- Research Teams 1 available results
- e-Learning Courses 487 available results
- Events 12 available results
- Open Research Data 1188 available results
displaying 1000 best results Help
Search results for: OUT-OF-POCKET SPENDING
-
Gdansk Bay sea bed sounding and classification of its results
PublicationThe main goal of this paper is to describe the results of sounding the Gdansk Bay sea bed by using a SES-2000 Standard parametric sub-bottom profiler. Quality of data obtained during trials depends inter alia on a proper location of transducer array to reduce influence of pitch, roll and heave motions as well as ship self noise (resulting from bubbles due to propeller and flow around hull, vibration generated by main engine and...
-
Impact of blending with polystyrene on the microstructural and electrochemical properties of SiOC ceramic
PublicationIn this work, we present the electrochemical behavior and microstructural analysis of silicon oxycarbide (SiOC) ceramics influenced by an addition of polystyrene (PS). Polymer-derived ceramics were obtained by pyrolysis (1000°C, Ar atmosphere) of different polysiloxanes prepared by sol–gel synthesis. This method is very effective to obtain desired composition of final ceramic. Two alkoxysilanes phenylthriethoxysilane and diphenyldimethoxysilane...
-
Spinning Fluids Reactor: A new design of a gas – liquid contactor
PublicationCurrent trends in chemical reactor design are based on adapting these to the requirements of a particular chemical process. Processes involving reactions between the gas and liquid phase in particular require precise adjustment of all parameters. The common denominator for most modern design solutions is enhancement of the mass transfer area and the overall volumetric mass transfer coefficient. Gas – liquid contactors evolved from...
-
Underfrequency Load Shedding: An Innovative Algorithm Based on Fuzzy Logic
PublicationIn contemporary power systems, the load shedding schemes are typically based on disconnecting a pre-specified amount of load after the frequency drops below a predetermined value. The actual conditions at the time of disturbance may largely dier from the assumptions, which can lead to non-optimal or ineective operation of the load shedding scheme. For many years, increasing the eectiveness of the underfrequency load shedding (UFLS)...
-
FEM simulation of laminate failure in the three point bending
PublicationThe paper presents a FEM simulation of failure of laminate subjected to the three point bending. The numeri-cal model is based on the equivalent single layer approach with 6-paramater non-linear shell theory kinematics. It is implemented in the non-commercial FEM code. The failure initiation is detected with the use of Tsai-Wu criterion. After the failure onset the progressive failure process is modelled through the appropriate...
-
Innovative Cold-formed GEB Section under Bending
PublicationThis paper is concerned with the numerical bending capacity study of the innovative cold-formed GEB sections. Both linear buckling analysis and non-linear static analysis incorporating geometric and material nonlinearity were carried out employing a shell structural model. The magnitudes of buckling load and limit load with respect to GEB section depth and thickness were obtained. The opened cold-formed section was tested assuming...
-
Higher-Order Statistics for Fluctuation-Enhanced Gas-Sensing.
PublicationPrzedstawiono wyniki badań eksperymentalnych wykrywania wybranych mieszanin gazów za pomocą analizy fluktuacji rezystancji obserwowanych w sensorach gazu. Do analizy obserwowanych fluktuacji wykorzystano gęstość widmową mocy oraz funkcję bispektrum.
-
Gas sensing by resistance fluctuations in PdxWO3 nanoparticle films.
PublicationPrzedstawiono wyniki badań sensorów gazu wykonanych z nanocząstek WO3 z dodatkiem Pd. Stwierdzono, że badanie fluktuacji rezystancji tych sensorów może istotnie zwiększyć czułość wykrywania gazu w porównaniu z obserwacją wyłącznie rezystancji stałoprądowej.
-
Application of CDMA modulated signals in seafloor remote sensing
PublicationW artykule omowiono zastosowanie modulacji CDMA w procesie detekcji echa od dna. Wyniki badan przedstawone zostaly dla symulacji z wykorzystaniem symulatora BORIS.
-
Noise measurement setups for fluctuations enhanced gas sensing
PublicationObserwacje zjawisk fluktuacyjnych w sensorach gazów pozwala zwiększyć czułość i selektywność detekcji gazów. Problemem jest budowa prostego i taniego systemu do obserwacji tych zjawisk. W artykule przedstawiono dwa systemy pozwalające na obserwacje szumów w rezystancyjnych sensorach gazów dostępnych na rynku i prototypowych, wykonanych z warstwy nanocząstek o zbliżonych wymiarach.
-
Fractal dimension for bending–torsion fatigue fracture characterisation
Publication -
Fluctuation-Enhanced Sensing for Biological Agent Detection and Identification
PublicationPrzedstawiono wcześniejsze wyniki badań dotyczące trzech różnych sposobów wykrywania obecności substancji biologicznych za pomocą zjawisk fluktuacyjnych: 1) wirusów wnikających do komórek, 2) zapachów emitowanych przez mikroby, 3) rozkładu widma i wartości chwilowych szumów podczas rozpraszania światła używanego do wykrywania zarodników na podstawie wyznaczenia współczynnika dyfuzji opisująceo ich ruch.We survey and show our earlier...
-
An odor-sensing system - powerful technique for foodstuff studies
PublicationThis work examines gas sensor array technology combined with multivariate data processing methods and demonstrates a promising potential for rapid, non-destructive analysis of food. Main attention is focused on detailed description of sensor used in e-nose instruments, construction, and principle of operation of these systems. Moreover, this paper briefly reviews the progress in the field of artificial olfaction and future trends...
-
Liquid crystalline optical components for application in optical sensing
PublicationW artykule opisano proces wytwarzania pryzmatów Wollastona na bazie roztworu ciekłokrystalicznego ZLI-1957 i płytek falowych na bazie prekursora polimeru ciekłokrystalicznego RMS03-001. Przedstawiono uzyskane parametry optyczne elementów pod kątem ich potencjalnych aplikacji
-
Hazardous gases detection by fluctuation-enhanced gas sensing
PublicationW pracy przedstawiono układ pomiarowy oraz metodę za pomocą której można jednym rezystancyjnym czujnikiem gazów wykrywać dwa gazy: amoniak i siarkowodór. Podano wskaźnik jaki pozwala dokonać detekcji tych gazów już przy stężeniach rzędu pojedynczych ppm. Przebadano także powtarzalność wyników pomiarów w kilku egzemplarzach czujników.
-
Analytical fluctuation enhanced sensing by resistive gas sensors
PublicationResistance fluctuations across polarised resistive gas sensors were studied in detail to evaluate sensor working conditions for detecting methane and ammonia at various concentrations. The 1/f noise component typically dominates other noise sources up to a few kHz and can be utilised to improve gas selectivity when compared with measurements of the sensor DC resistance. The Arrhenius plot was created and the activation energy for...
-
Remote sensing and photogrammetry techniques in diagnostics of concrete structures
PublicationRecently laser scanning technologies become widely used in many areas of the modern economy. In the following paper authors show a potential spectrum of use Terrestrial Laser Scanning (TLS) in diagnostics of reinforced concrete elements. Based on modes of failure analysis of reinforcement concrete beam authors describe downsides and advantages of adaptation of terrestrial laser scanning to this purpose, moreover reveal under which...
-
3D polypyrrole structures as a sensing material for glucose detection
PublicationIn this work, 3D polypyrrole (PPy) structures as material for glucose detection is proposed. Polypyrrole was electrochemically polymerized on platinum screen-printed electrode from an aqueous solution of lithium perchlorate and pyrrole. The growth mechanism of such PPy structures was studied by ex-situ scanning electron microscopy. Preliminary studies show that studied here PPy film is a good candidate as a sensing material for...
-
Graphene field-effect transistor application for flow sensing
PublicationMicroflow sensors offer great potential for applications in microfluidics and lab-on-a-chip systems. However, thermal-based sensors, which are commonly used in modern flow sensing technology, are mainly made of materials with positive temperature coefficients (PTC) and suffer from a self-heating effect and slow response time. Therefore, the design of novel devices and careful selection of materials are required to improve the overall...
-
Nitrogen dioxide sensing properties of PEDOT polymer films
PublicationThis work presents a simple and fully electrochemical route for the polymerization of poly(3,4-ethylenedioxytiophene) (PEDOT) films for fabricating a NO2 gas sensor prepared by electropolymerization of 3,4-Ethylenedioxythiophene (EDOT) monomer in lithium perchlorate/acetonitrile solution. The main aim of this study is to determine the sensing properties of conductive polymer at elevated temperatures. The effects of the humidity,...
-
Acoustic Sensing Analytics Applied to Speech in Reverberation Conditions
PublicationThe paper aims to discuss a case study of sensing analytics and technology in acoustics when applied to reverberation conditions. Reverberation is one of the issues that makes speech in indoor spaces challenging to understand. This problem is particularly critical in large spaces with few absorbing or diffusing surfaces. One of the natural remedies to improve speech intelligibility in such conditions may be achieved through speaking...
-
Fractal dimension for bending–torsion fatigue fracture characterisation
PublicationFracture surfaces after biaxial fatigue tests were compared using fractal dimension for three types of metallic materials in smooth and notched specimens made of S355J2 and 10HNAP steels and 2017-T4 aluminium alloy, considering both proportional and nonproportional cyclic loading. High-resolution optical 3D measurement studies were performed on the entire fracture surface. A direct correlation between fractal dimension and fatigue...
-
Embedded gas sensing setup for air samples analysis
PublicationThis paper describes a measurement setup (eNose) designed to analyze air samples containing various volatile organic compounds (VOCs). The setup utilizes a set of resistive gas sensors of divergent gas selectivity and sensitivity. Some of the applied sensors are commercially available and were proposed recently to reduce their consumed energy. The sensors detect various VOCs at sensitivities determined by metal oxide sensors’ technology...
-
Zagrożenia bezpieczeństwa IT/OT
PublicationZłośliwe oprogramowanie, obok ataków rozproszonej odmowy świadczenia usług (ang. Distributed Denial of Servi-ce – DDoS), podszywania, SPAMu oraz ogólnie niechcianej komunikacji, stanowi aktualnie jedną z najważniejszych kwestii bezpieczeństwa. Sam termin (Malicious Software – Malware) określa zbiorczo między innymi wirusy, konie trojańskie i robaki komputerowe. Ostateczne rozwiązanie wspomnianych zagrożeń bezpieczeństwa wymaga...
-
Association between Gut Dysbiosis and the Occurrence of SIBO, LIBO, SIFO and IMO
Publication -
Gut microbiota in dementia. Critical review of novel findings and their potential application
Publication -
The impact of gasification wastewater on soil microorganisms and the growth of oat and red clover
Publication -
IT support for OKNO broadband Internet-based distant learning system at WUT
Publication -
Our Europe. Ethnography - Ethnology - Anthropology of Culture
Journals -
Combined computational-experimental approach to predict blood–brain barrier (BBB) permeation based on “green” salting-out thin layer chromatography supported by simple molecular descriptors
Publication -
Green, simple analytical method for biogenic amines determination in fruit juice samples using salting-out assisted liquid-liquid microextraction and gas chromatography-mass spectrometry
PublicationSalting-out assisted liquid-liquid microextraction (SALLME) was integrated with the derivatization procedure to establish a one-step sample pre-treatment approach for rapid analysis of 14 biogenic amines (BAs) in fruit juices. The methodology consists of salting-out of analytes, derivatization with ethyl chloroformate (ECF), extraction with ethyl acetate (EtAc), and the analysis of the derivatized BAs using gas chromatography-mass...
-
Computational fluid dynamics simulation of heat transfer from densely packed gold nanoparticles to isotropic media
PublicationThis work aims to determine and compare heat generation and propagation of densely packed gold nanoparticles (Au NPs) induced by a resonant laser beam (532 nm) according to the Mie theory. The heat flux propagation is transferred into the materials, which here are: silica glass; soda-lime-silica glass; borosilicate glass; polymethyl methacrylate (PMMA); polycarbonate (PC); and polydimetylosiloxane (PDMS). This analysis aims to...
-
The first manganese trialkoxysilanethiolates: formation, properties and structure of solvent ligated complexes - [Mn{SSi(OBut)3}2(MeCN)] and [Mn{SSi(OBut)3}2(MeOH)4]
PublicationW pracy przedstawiono otrzymywanie i strukturę pierwszych trialkoksysilanotiolanowych kompleksów manganu(II). Syntezy prowadzone były reakcji 2≡SiSH+ MnCl2 + 2Et3N = (≡SiS)2Mn + 2Et3N.HCl doprowadziły do otrzymania nowych kompleksów: [Mn{SSi(OBut)3}2(MeOH)4] (gdy jako rozpuszczalnik zastosowano MeOH) oraz [Mn{SSi(OBut)3}2(NCCH3)], gdy w badaniach posłużono się acetonitrylem.
-
Quantum superadditivity in linear optics networks: Sending bits via multiple-access Gaussian channels
PublicationSuperadditivity effects of communication capacities are known in the case of discrete variable quantum channels. We describe the continuous variable analog of one of these effects in the framework of Gaussian multiple access channels (MACs). Classically, superadditivity-type effects are strongly restricted: For example, adding resources to one sender is never advantageous to other senders in sending their respective information...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-002)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-Con)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-004)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-006)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Processing data on sea bottom structure obtained by means of the parametric sounding
PublicationThe aim of the paper is to analyze data obtained during sounding the Gdansk Bay sea bed by means of the parametric echo-sounder. The accuracy of the sea bottom structure investigation needs correct configuration of research equipment and proper calibration of peripheral devices (GPS, heading sensor, MRU-Z motion sensor and navigation instruments which provide necessary data to bathymetrical measurement system, enabling its work...
-
Electronic structure and magnetism of samarium and neodymium adatoms on free-standing graphene
PublicationThe electronic structure of selected rare-earth atoms adsorbed on a free-standing graphene was investigated using methods beyond the conventional density functional theory (DFT+U, DFT +HIA, and DFT+ED). The influence of the electron correlations and the spin-orbit coupling on the magnetic properties has been examined. The DFT+U method predicts both atoms to carry local magnetic moments (spin and orbital) contrary to a nonmagnetic...
-
Binder availability and blending efficiency of reclaimed asphalt: A state-of-the-art review
Publication -
The Fluoride Content of Yerba Mate Depending on the Country of Origin and the Conditions of the Infusion
Publication -
Mineral Composition and Antioxidant Potential of Coffee Beverages Depending on the Brewing Method
Publication -
Sounding Mechanism of a Flue Organ Pipe—A Multi-Sensor Measurement Approach
PublicationThis work presents an approach that integrates the results of measuring, analyzing, and modeling air flow phenomena driven by pressurized air in a flue organ pipe. The investigation concerns a Bourdon organ pipe. Measurements are performed in an anechoic chamber using the Cartesian robot equipped with a 3D acoustic vector sensor (AVS) that acquires both acoustic pressure and air particle velocity. Also, a high-speed camera is employed...
-
Analysis of cyclone separator solutions depending on SEC outlet conditions in nCO2PP
PublicationUtilization of spray ejector condenser in order to carry out direct-contact condensation of vapour with inert gas (CO2) on a spray of subcooled liquid integrated with separator (to make pure CO2) has been proposed for the task of condensation and CO2 separation in the negative CO2 emission gas power plant. Condensation and separation has a significant impact on the thermodynamic efficiency of the entire negative CO2 emission gas...
-
Time variable gain for long range sonar with chirp sounding signal
PublicationThe main purpose of applaying Time Variable Gain (TVG) in active sonars with digital signal processing is to reduce dynamic range of echo signal and adapt it to the dynamic range of the analogue to digital conversion. With high transmission losses level, the dynamic range of the input signal in long range sonars can be very high and even exceed 200dB. When chirp sounding signals with matched filtration are used, sonars can raech...
-
Melting and crystallization DSC profiles of milk fat depending on selected factors
Publication -
Nutritional Status and the Outcomes of Endoscopic Stenting in Benign and Malignant Diseases of Esophagus
Publication -
Processing data on sea bottom structure obtained by means of the parametric sounding
PublicationThe aim of the paper is to analyze data obtain during sounding of the Gdansk Bay by means of the parametric sonar. The accuracy of the sea bottom structure investigation needs the correct configuration of research equipment and the proper calibration of peripheral devices (GPS, heading sensor, motion sensor MRU-Z and navigation units) which provide necessary data to bathymetrical measurement system enabling its work with whole...
-
Electrostatic Zipping Actuators—Analysis of the Pull-In Effect Depending on the Geometry Parameters
PublicationContinuous work on a new generation of actuators, referred to as artificial muscles, resulted in the initiation of work on electrostatic zipping actuators, the concept of which is derived from micro electro-mechanical devices. Despite partial knowledge of their basic operating parameters, a question remains whether electrostatic zipping actuators are able to meet the expectations in the context of generated forces and control possibilities....