displaying 1000 best results Help
Search results for: ATMOSPHERIC CORROSION
-
High temperature corrosion of evaporator tubes in low-emission steam boilers
PublicationW artykule opisano zjawisko korozji wysokotemperaturowej rur ekranowych kotłów parowych niskoemisyjnych. Przeprowadzono badania rur po eksploatacji. Wykonano badania składu chemicznego zgorzelin. Stwierdzono, że główną przyczyną pocienienia rur na wyższych poziomach jest korozja siarkowa, natomiast na poziomach niższych oddziaływanie stopionych soli.
-
Investigations into tendency to stress corrosion of joints welded in austenitic and duplex steels
PublicationPrzedstawiono wyniki badań spawanych złączy różnoimiennych wykonanych ze stali austenitycznej oraz typu duplex 2205. Badania podatności do korozji naprężeniowej złączy wykonano metodą odkształcania z małą prędkością. Próby przeprowadzono w środowisku obojętnym oraz agresywnym (MgCl2).
-
EVALUATION OF CAUSES OF CORROSION OF HEATING PIPES AND BALLAST CHAMBERS ON HLVJ INNOVATION
Publication..
-
Diaryl Sulfide Derivatives as Potential Iron Corrosion Inhibitors: A Computational Study
PublicationThe present work aimed to assess six diaryl sulfide derivatives as potential corrosion inhibitors. These derivatives were compared with dapsone (4,4′-diaminodiphenyl sulfone), a common leprosy antibiotic that has been shown to resist the corrosion of mild steel in acidic media with a corrosion efficiency exceeding 90%. Since all the studied compounds possess a common molecular backbone (diphenyl sulfide), dapsone was taken as the...
-
Novel fast non-linear electrochemical impedance method for corrosion investigations
PublicationThe paper presents a novel approach to corrosion rate monitoring using non-linear electrochemical impedance spectroscopy. The authors propose a new variant of non-linear impedance measurement using amplitude-modulated multi-frequency ac perturbation signal. It allows shortening of measurement duration so it is possible to monitor corrosion rate of the systems experiencing rapid changes. In this way a limitation resulting from lack...
-
The Impact of Crushed Rock Spoil on Pitting Corrosion of Selected Stainless Steel
PublicationThe paper presents the results of the pitting resistance investigations of selected stainless steels in the chloride environment and the simultaneous impact of erosive factors using the cyclic polarization technique. Additionally, using electrochemical techniques, ie: electrochemical impedance spectroscopy (EIS) and measurement of corrosion potential, the behavior of the passive layer of selected stainless steels in the environment...
-
Evaluation of reinforcement corrosion rate in concrete structures by electrochemical noise measurements
PublicationW pracy przedstawiono wyniki obliczeń rezystancji polaryzacyjnej w układzie złożonym z dwóch elektrod (ze stali węglowej oraz elektrody odniesienia), umieszczonych w otulinie betonowej. Szybkość korozji ulega zmianom uzależnionym od stopnia nasiąknięcia betonu roztworem zawierającym jony chlorkowe. Zmiany rezystancji polaryzacyjnej elektrody stalowej oceniane są na podstawie pomiarów prądowego i potencjałowego szumu elektrochemicznego....
-
Imaging of the effects of pitting corrosion with the use of AFM
Open Research DataPitting corrosion is a local attack on a metal surface, limited to a point or small area, which appears as a hole. Pitting corrosion is one of the most harmful forms of corrosion due to the fact that it is associated with small, difficult to detect damage, that can even lead to perforation of the structure. A single pit may range in size from micrometers...
-
SEM micrographs of Ti tooth implant corrosion
Open Research DataThe dataset contains micrographs made with a scanning electron microscope (SEM) Hitachi S-3400N of the tooth implant removed after inflammation. The inflammation was induced by the increased corrosion rate of the titanium screw. The reason for the corrosion to occur was the appearance of the concentration cell of different aeration for various areas...
-
The influence of the spatial distribution of leads and ice floes on the atmospheric boundary layer over fragmented sea ice
Publication -
Pobieranie próbek opadów i osadów atmosferycznych do analizy. Sampling of atmospheric precipitation and deposits for the analysis.
PublicationOmówiono różne typy próbników stosowanych do pobierania próbek opadów i osadów atmosferycznych (mgła i woda z chmur, rosa i szadź). Zaprezentowano urządzenia o różnym stopniu automatyzacji. Przedstawiono również informacje literaturowe na temat oznaczania związków nieorganicznych i organicznych w próbkach opadów i osadów atmosferycznych z zastosowaniem odpowiednich technik pomiarowych.
-
Rapid eradication of bacterial phytopathogens by atmospheric pressure glow discharge generated in contact with a flowing liquid cathode
Publication -
Comprehensive studies on the properties of apple juice treated by non-thermal atmospheric plasma in a flow-through system
Publication -
Ceramic atmospheric pressure micro glow discharge device with evaporating liquid flowing cathode for analytical purposes
Publication -
Variations in the near-surface atmospheric electric field at high latitudes and ionospheric potential during geomagnetic perturbations
Publication -
Effect of substorms in the Earth’s nightside sector on variations in the surface atmospheric electric field at polar and equatorial latitudes
Publication -
An analytical performance of atmospheric pressure glow discharge generated in contact with flowing small size liquid cathode
Publication -
Direct elemental analysis of honeys by atmospheric pressure glow discharge generated in contact with a flowing liquid cathode
Publication -
Ocena jakości powietrza atmosferycznego na terenie Aglomeracji Trojmiejskiej = Quality of atmospheric air in the Tricity area
PublicationNa terenie Aglomeracji Trójmiejskiej i Tczewa monitoring jakości powietrza prowadzony jest, obok jednostek samorządowych przez fundację: Agencja Monitoringu Regionalnego Atmosfery Aglomeracji Gdańskiej - ARMAAG. Katedra Chemii Analitycznej PG współpracując z fundacją ARMAAG podjęła próbę uzupełnienia informacji na temat stanu atmosfery na terenie Trójmiasta i Tczewa o ocenę pod względem zawartości analitów z grupy BTEX. Celem...
-
Optical Emission Spectroscopy of Microwave (915 MHz) Plasma in Atmospheric Pressure Nitrogen with Addition of Ethanol Vapour
PublicationIn this paper results of optical emission spectroscopic study of microwave 915 MHz plasma in atmospheric pressure nitrogen with an addition of ethanol vapour are presented. The plasma was generated in waveguide- -supplied cylinder-type nozzleless microwave plasma source. The aim of research was to determine the rotational Trot and vibrational Tvib temperatures of CN and C2. A method called bubbling was employed to introduce alcohol (ethanol)...
-
Electrochemical noise analysis methods for the investigation of corrpsion processes
PublicationProcesy korozji mogą być badane przez obserwacje przepływu ładunków między elektrolitem a korodującą elektrodą metalową. Przepływy te są obserwowane jako fluktuacje prądu i napięcia nazywane szumem elektrochemicznym. Różne rodzaje procesów korozji mogą być identyfikowane za pomocą szumów elektrochemicznych. Szybkość korozji jednorodnej jest określana przez estymację rezystancji polaryzacji występującej między elektrolitem a metalem....
-
Determination of causes of accelerated local corrosion of austenitic steels in water supply systems
PublicationThis paper concerns an inspection of a water supply system, made of AISI 304 steel, which showed signs of local corrosion at the weld. Such corrosion caused material perforation after very short periods of operation. It was revealed that steel was sensitised during the welding process. It was also proven that chromium micro-segregation occurred in the alloy leading to galvanic cell formation which initialised the process of pitting...
-
Influence of water salinity on corrosion risk - the case of the southern Baltic Sea coast.
PublicationWater corrosivity in Gdansk Bay, Poland, the southern part of the Baltic Sea, was investigated. The analysed region is heavily industrialized, and the coastline is very diverse. Twenty-seven test points along the coastline were selected. Water parameters such as salinity, total dissolved solids content, resistivity, conductivity, oxygenation, pH and corrosion rate were determined. The results of the investigation are presented....
-
Investigation of pitting corrosion of stainless steel by means of acoustic emission and potentiodynamic methods
Publication -
Complex Corrosion Monitoring System for Crude Distillation Unit in Form of Neutral Network
PublicationComplex and successful corrosion monitoring of refinery processes can significantly reduce material losses and failure risk. The developed corrosion monitoring system is based on online ultrasonic sensors, ER (electrical resistance) probes, gravimetric method and multipoint analytical analysis of chemical composition of the fluids. Additional online LPR (linear polarization resistance) sensors controlling corrosiveness of sour...
-
Acoustic Emission Monitoring of Structural Elements of a Ship for Detection of Fatigue and Corrosion Damages
PublicationUszkodzenia korozyjne i pęknięcia zmęczeniowe są głównymi przyczynami defektów strukturalnych we wszystkich środkach transportu takich jak statki, cysterny drogowe i kolejowe. Oba typy degradacji tzn. degradacja materiału i konstrukcji są przedmiotem badań przeprowadzanych w projekcie badawczym VII Programu Ramowego Unii Europejskiej o nazwie ''Monitorowanie efektywnych kosztów korozji i zmęczenia w środkach transportu'' (akronim...
-
Corrosion behavior of hydrogen charged super duplex stainless steel welded joints
PublicationThe electrochemical behavior of the weld metal, heat-affected zone (HAZ), and base material of super duplex stainless steel (SDSS) welded joints, made with the application of flux-cored arc welding (FCAW) and submerged arc welding (SAW), were investigated with the use of metallographic examinations (optical microscopy and scanning electron microscopy), potentiodynamic polarization measurements and total hydrogen content determination...
-
Analysis of features of stainless steels in dissimilar welded joints in chloride inducted corrosion
PublicationStainless steels of femtic-austenitic microstructure that means the duplex Cr-Ni-Mo steels, in comparison with austenitic steel includes less expensive nickel and has much better mechanical properties with good formability and corrosion resistance, even in environments containing chloride ions. Similar share of high chromium ferrite and austenite, which is characterized by high ductility, determines that the duplex steels have...
-
Corrosion and Cavitation Resistances of Low Alloy Steel After Frictional-Mechanical Treatment
PublicationPaper presents the results of the studies of wear, corrosion and cavitation resistances of the S355J2 low alloy medium carbon steel subjected to surface modification by friction-mechanical treatment, as tested in sea water simulated solution. To evaluate the effect of the surface treatment, the comparative studies of the corrosive properties of the steel before and after treatment have been considered. The treatment due to a severe...
-
Influence of yttria surface modification on high temperature corrosion of porous Ni22Cr alloy
PublicationProtective coatings for porous alloys for high temperature use are relatively new materials. Their main drawback is high temperature corrosion. In this work protective coatings based the on Y-precursor infiltrated into the sintered Ni22Cr alloys are studied at 700°C. Effects of the amount of the protective phase on the resulting corrosion properties are evaluated in air and humidified hydrogen. Weight gain of the samples, their...
-
Fabrication of anti-corrosion nitrogen doped graphene oxide coatings by electrophoretic deposition
PublicationThis work assesses anti-corrosion properties of graphene and N-doped graphene coatings deposited on copper by an electrophoretic method. Graphene oxide (GO) precursor was synthesized by an improved Hummers' method, whereas N-doping was performed hydrothermally in the presence of ammonia. After nitrogenation, doped graphene oxide samples (NGO) contained a reduced amount of oxygen and about 9% w/w nitrogen as pyridinic, pyrrole,...
-
Experimental study of corrosion in reinforced concrete by acoustic emission and electrochemical noise techniques
PublicationTechnika emisji akustycznej jest znaną metodą badań korozji zbrojenia żelbetu. Źródłem aktywności akustycznej są zawsze zjawiska o naturze mechanicznej. Przedstawiono wynik badań akustycznych zbrojonego betonu w warunkach polaryzacji anodowej, przyspieszającej procesy korozyjne. Symultanicznie prowadzona była rejestracja szumu elektrochemicznego. Dla umożliwienia korelacji wyników, uzyskanych obiema technikami, wykonana została...
-
Corrosion characteristics of the AL-Si alloy after laser treatment at cryogenic conditions
PublicationOmówiono wpływ laserowego powierzchniowego przetapiania stopu Al-Si w warunkach kriogenicznych na jego mikrostrukturę i właściwości użytkowe. W wyniku badań korozyjnych stwierdzono zwiększenie odporności na korozję stopu Al-Siw 0,01 M roztworze H2SO4.
-
Elektrochemiczne badania korozyjne stali do azotowania.Electrochemical corrosion tests of nitriding steels
PublicationPrzedstawiono badania elektrochemiczne podatności na korozję stali do azotowania gatunków 31CrMoV9 i 34CrAlNi7-10 oraz warstw azotowanych jarzeniowo. Badania wykonano metodą potencjoskokową w środowisku słabo kwaśnym.
-
Cavitation erosion of some laser-produced iron-base corrosion-resistance alloys
PublicationW pracy przedstawiono badania kawitacyjne stali C45, X20Cr13 oraz X5CrNi18-10 po laserowym stopowaniu ich warstwy wierzchniej proszkami Mn, Cr, Ni, Si, Ti, Co, Al, Mo, B. Badania kawitacyjne prowadzono na stanowisku z wirującą tarczą. Zniszczenia powierzchni w okresie inkubacji oceniano metodą optyczną. Przedstawiono związek pomiędzy uzyskaną mikrostrukturą obrabianej warstwy i jej odpornością kawitacyjną.
-
Long-term researches of stress corrosion cracking of Al-Zn-Mg alloys
PublicationPraca przedstawia wyniki odporności na korozję naprężeniową stopów Al-Zn-Mg uzyskane w warunkach stacjonarnych. Dodatkowo określono wpływ składu chemicznego oraz obróbki cieplnej na odporność korozyjną tych stopów. Badania prowadzono w 3% NaCl w warunkach stałego obciążenia σ = 0.8R0.2 przez 1500 godzin. Stwierdzono, iż zawartość Zn i Mg oraz szybkość chłodzenia to główne czynniki wpływające na podatność tych stopów na korozje...
-
Cobalt Base Clad Layer Resistance On The Corrosion Under Low Sulfur Preassure
PublicationNapawane laserowo warstwy ze stopu kobaltu, zostały poddane siarkowaniu przy niskich ciśnieniach cząstkowych w temperaturze 800 stopni celsiusza prze 24 godziny. Uzyskano warstwę zgorzeliny zróżnicowaną w zależności od zastosowanego ciśnienia. W obu jednak przypadkach podobne były zmiany zachodzące w warstwie po zgorzeliną - degradacja węglików i intensywna korozja wzdłuż granic dendrytów.
-
Fabrication of anti-corrosion nitrogen doped graphene oxide coatings by electrophoretic deposition
Publication -
An investigation of microstructural basis for corrosion behavior of Al-CNT composites fabricated by SPS
PublicationIn this research effect of the addition of multi-wall carbon nanotubes (MWCNTs) as additive powder on microstructure and corrosion behavior of fabricated Al-CNT composites was studied. The aluminum powder and CNTs were mixed with high energy planetary ball-mill. It is observed that by increasing milling time, the uniformity of CNTs on aluminum matrix and consequently corrosion resistance of Al-CNT composite is increased. On the...
-
Nondestructive corrosion degradation assessment based on asymmetry of guided wave propagation field
PublicationThe article presents the results of numerical and experimental investigation of guided wave propagation in steel plates subjected to corrosion degradation. The development of novel procedures allowing for the assessment of the corrosion degradation level is crucial in the effective diagnostics of offshore and ship structures that are especially subjected to aggressive environments. The study’s main aim is to investigate the influence...
-
Characterization of corrosion in reinforced concrete beams using destructive and non-destructive tests
PublicationThe paper presents both non-destructive and destructive experimental tests on steel-reinforced concrete beams subjected to electrochemical corrosion. To examine the condition and behavior of the specimens, destructive tests were carried out, i.e., a three-point bending together with a modulated ultrasonic wave test. In addition, a series of non-destructive experiments were conducted, such as the potential measurement method, low-frequency...
-
Morphology and corrosion characteristics of laser surface remelted Al-Sialloy at cryogenic conditions
PublicationPrzedstawiono koncepcję obróbki laserowej stopu Al-Si w warunkach kriogenicznych. Określono jej wpływ na lokalny skład chemiczny oraz mikrostrukturę i właściwości korozyjne wymienionego stopu. Stwierdzono znaczącą poprawę właściwości korozyjnych w 0,01 M H2SO4.
-
Experimental ultimate strength assessment of stiffened plates subjected to marine immersed corrosion
PublicationThis study experimentally analyses the impact of marine immersed corrosion degradation on the compressive strength of the stiffened plates where the lower degradation levels were considered. The corrosion degradation test was accelerated by controlling the natural corrosion environmental factors, avoiding applying an electric current. Different groups of corrosion degradation levels and initial plate thicknesses were investigated....
-
Deis assessment of intergranular corrosion process proceeding on AISI 304 stainless steel
PublicationW pracy przedstawiono nowe podejście do badania mechanizmu i intensywności korozji międzykrystalicznej. Badania przeprowadzono przy wykorzystaniu techniki dynamicznej elektrochemicznej spektroskopii impedancyjnej (DEIS), która pozwala na jednoczesne rejestrowanie chwilowych zmian impedancji oraz prądu stałego badanego układu. Tym samym możliwe jest otrzymanie z jednego pomiaru informacji dotyczących zarówno mechanizmu korozji międzykrystalicznej,...
-
Wear and corrosion characteristics of the layers type (mn-p) formed on aluminium alloys
Publicationopisano multipleksową metodę wytwarzania warstw zawierających mangan i fosfor (mn-p) na stopach aluminium. przedstawiono wyniki badań mikrostruktury, właściwości tribologicznych i korozyjnych tych warstw. stwierdzono obecność tlenku manganu i fosforku manganu w wytworzonych warstwach oraz ich wysoką twardość, rzędu 1272 hv0,02. warstwy typu (mn-p) zmniejszają podatność stopu alsi13mg1cuni na korozję w 0,01 mh2so4.
-
Ultrafine grained Mg-1Zn-1Mn-0.3Zr alloy and its corrosion behaviour
Publication -
Effect of native air-formed oxidation on the corrosion behavior of AA7075 aluminum alloys
PublicationThe microstructure of aluminum alloys plays a key role in their corrosion resistance. In particular, the presence of intermetallic precipitates differing in the potential from the alloy matrix induces local corrosion. The study presents the effect of native air-formed oxidation on the corrosion behavior of AA 7075 aluminum alloy. Various microscopic and spectroscopic techniques were used to examine the changes occurring in the...
-
Effect of microstructure on mechanical properties and corrosion resistance of 2205 duplex stainless steel
PublicationThis paper presents results of the research on impact of microstructure of austenitic-ferritic steel of duplex type on its mechanical properties and susceptibility to stress corrosion cracking. As showed, improper processing technologies more and more often used in shipbuilding industry for plates and other half-finished products made of duplex steel may cause significant lowering their properties, which frequently makes their...
-
Influence of laser remelting at cryogenic conditions on corrosion resistance of non-ferrous alloys
PublicationCelem nadtapiania laserowego elementów wytwarzanych z stopów aluminium, miedzi i tytanu jest uzyskanie wysokiej twadrości i odporności na korozję dla wydłużenia okresu ich eksploatacji w rezultacie ich szybkiej krystalizacji. Końcowa mikrostruktura, skład fazowy i właściwości wymienionych stopów zależą od parametrów obróbki laserowej oraz budowy wykresów równowagi fazowej. W artykule przedstawiono wpływ laserowego nadtapiania...
-
Corrosion resistance of sintered duplex stainless steels in the salt fog spray test
Publication