Filters
total: 3497
-
Catalog
displaying 1000 best results Help
Search results for: KERATIN FIBERS
-
Optimization of the Aeration Strategies in a Deammonification Sequencing Batch Reactor for Efficient Nitrogen Removal and Mitigation of N2O Production
PublicationIn deammonification systems, nitrite-oxidizing bacteria (NOB) suppression and nitrous oxide (N2O) mitigation are two important operational objectives. To carry out this multivariable analysis of response, a comprehensive model for the N cycle was developed and evaluated against experimental data from a laboratory-scale deammonification granular sludge sequencing batch reactor. Different aeration strategies were tested, and the manipulated...
-
Structural Assessment of Reinforced Concrete Beams Incorporating Waste Plastic Straws
PublicationThe behavior of reinforced concrete beams containing fibers made of waste plastic straws (WPSs) under the three point bending test is examined. The effect of WPS fiber addition on the compressive and split tensile strength is reported. Four concrete mixes were prepared. The control mix PS-0 had a proportion of 1 cement: 1 sand: 2 coarse aggregate and a water cement ratio of 0.4. In the other three mixes PS-0.5, PS-1.5 and PS-3,...
-
<title>Manufacturing and measurements of triple-core, double-core, and twin-core single-mode soft-glass optical fibers</title>
Publication -
The State Of Lightguide Technology In Poland On The Basis Of The IV National Symposium "Optical Fibres And Their Applications"
Publication -
Nanocrystalline CVD Diamond Coatings on Fused Silica Optical Fibres: Optical Properties Study
Publicationpre-treatment by dip coating in two detonation nanodiamond (DND) seeding media has been studied. The DND suspension in ethyl alcohol and dispersion of DND in dimethyl sulfoxide (DMSO) with polyvinyl alcohol (PVA) were chosen for the seeding purpose. The grain size distribution of nanodiamond particles in both seeding media was kept at the same level (approximately 1050 nm). After the seeding nanocrystalline diamond lms were deposited...
-
Exploration of optical fibres as a carrier for new benzene and toluene matrix-free reference materials
PublicationTo meet high expectations concerning precision and accuracy of reference materials, preparation of matrixfree reference materials using thermal decomposition-gas chromatography-mass spectrometry (TD-GC-MS) was proposed in this study. In the paper, the results obtained in preparation of the new reference materials for benzene and toluene are presented, based on the thermal decomposition technique of compounds chemically bound to...
-
Polyethylene glycol-coated solid-phase microextraction fibres for the extraction of polar analytes-A review
PublicationThe article discusses the merits and limitations of commercially available solid-phase microextraction (SPME) fibres and compares them with the new type of extraction coatings, in particular those containing polyethylene glycol as sorbent, as well as the methods of the preparation of the latter. It also analyses their possible application for the extraction of a broad spectrum of analytes, with particular emphasis on the sampling...
-
Preparation, morphology and properties of natural rubber composites filled with untreated short jute fibres
PublicationGreen composites were obtained by incorporation of short jute fibres in natural rubber matrix using a laboratory two-roll mill. The influence of untreated fibre content (1, 2.5, 5, 7.5 and 10 phr) on the mechanical properties, dynamic mechanical properties, swelling properties was examined. The behaviour of prepared green composites under cyclic compression was also investigated. Fibre dispersion in rubber matrix was studied by...
-
Nucleation and growth of CVD diamond on fused silica optical fibres with titanium dioxide interlayer
PublicationNucleation and growth processes of thin diamond films on fused silica optical fibres have been investigated. Fibres were coated with diamond film using microwave plasma enhanced chemical vapour deposition (µPE CVD) system. Since the growth of diamond on the fused silica glass requires high seeding density, two types of glass pre-treatment were applied: titanium dioxide (TiO2) interlayer deposition and sonication in nanodiamond...
-
Simulation of fracture process in concrete elements with steel fibres using discrete lattice model
PublicationArtykuł omawia wyniki modelowania procesu zarysowania w elementach betonowych zawierające stalowe włókna przy zastosowaniu dyskretnego modelu kratownicowego. Beton był modelowany na poziomie mezoskali z uwzględnieniem 5 faz: kruszywa, zaczynu cementowego, włókien i obu stref kontaktu. Obliczenia wykonano dla jednoosiowego ściskania, jednoosiowego rozciągania i zginania prostego.
-
Effect of steel fibres on concrete behavior in 2D and 3D simulations using lattice model.
PublicationW artykule przedstawiono wyniki numerycznej symulacji betonu zbrojonego włóknami stalowymi. Beton został opisany w skali mezo jako materiał 3-fazowy przy zastosowaniu modelu sieciowego. Obliczenia wykonano dla rozciągania jednoosiowego. Porównano ze sobą wyniki dwu- i trójwymiarowe.
-
Biobased Polyethylene Hybrid Composites with Natural Fiber: Mechanical, Thermal Properties, and Micromechanics
Publication -
The method of improving the dynamic range of jitter analyzers in optical-fiber transmission systems
Publication -
Ancient mitochondrial DNA and the genetic history of Eurasian beaver (Castor fiber) in Europe
Publication -
Chemically modified glass fiber as a matrix-free reference material for volatile compounds
PublicationW pracy opisano sposób wytwarzania nowego typu bezmatrycowych materiałów odniesienia lotnych związków organicznych. Do otrzymywania lotnych analitów wykorzystano technikę termicznego rozkładu związków powierzchniowych. Jako nośnik zastosowano modyfikowane chemicznie włókna szklane. Związkiem oznaczanym był chlorek metylu.
-
Nonlinearity shaping in nanostructured glass-diamond hybrid materials for optical fiber preforms
PublicationNanodiamond integration with optical fibers has proved a compelling methodology for magneto-optics. We reveal that the applicability of nanodiamonds in nonlinear optics goes beyond the previous demonstrations of frequency converters. Instead, we exploit the recently reported volumetric integration of nanodiamonds along the optical fiber core and show that the nonlinear response of glasses can be manipulated by nanodiamonds. By...
-
Data-Driven Modeling of Mechanical Properties of Fiber-Reinforced Concrete: A Critical Review
PublicationFiber-reinforced concrete (FRC) is extensively used in diverse structural engineering applications, and its mechanical properties are crucial for designing and evaluating its performance. The compressive, flexural, splitting tensile, and shear strengths of FRCs are among the most important attributes, which have been discussed more extensively than other properties. The accurate prediction of these properties, which are required...
-
High-Resolution, Broad-Range Detection Setup for Polarimetric Optical Fiber Sensors
PublicationA common-path polarization interferometer using a Wollaston prism and an area detector for the measurement of retardation or optical path difference is presented. Employing a moderate-resolution 1280 by 1024 pixel monochrome camera, it offers a measurement range of approximately 780 radians at 830 nm and 1350 radians at 515 nm while maintaining a high measurement resolution. Retardation introduced by a zero-order waveplate or a...
-
ZnO coated fiber optic microsphere sensor for the enhanced refractive index sensing
PublicationOptical fiber-based sensors are expected to become key components in the control of industrial processes,and the tuning and the enhancement of their sensing properties are crucial for the further developmentof this technology. Atomic Layer Deposition (ALD), a vapor phase technique allowing for the deposition ofconformal thin films, is particularly suited for the deposition of controllable thin films on challenging sub-strates....
-
Effect of sisal fiber filler on thermal properties of bio-based polyurethane composites
PublicationThis work is mainly focused on study of thermal and thermomechanical properties of obtained bio-based polyurethane (coded as bio-PU) composites via using different types of bio-components (bio-glycol, modified soybean oil and sisal fiber) in the procedure. The chemical structure, morphology and mechanical properties were also investigated and described in this manuscript in order to know more perfect characterization of produced...
-
Optical properties of thin TiO2 film deposited on the fiber optic sensor head
PublicationThe presented study was focused on investigation of the titanium dioxide (TiO2) thin film deposited on the fiber tip. The intention of this investigation was using TiO2 film in the construction of the optical fiber sensor head. In the demonstrated construction TiO2 thin layer was deposited on the tip of a commonly used telecommunication single mode optical fiber (SMF-28) by means of the Atomic Layer Deposition (ALD). Thickness...
-
Investigation on Mode I Fracture Behavior of Hybrid Fiber-Reinforced Geopolymer Composites
PublicationRecent reports in the literature have shown that fber-reinforced geopolymer composites (FRGC) made with monofbers exhibit a signifcant enhancement in fracture energy. However, many aspects of the fracture performance of hybrid fberreinforced geopolymer composites (HFRGC) remain largely unexploited, and these are predominant for the structures. For the frst time, the mode I fracture energy of HFRGC is investigated. The mode I behavior...
-
Experimental and Numerical Study on Mechanical Characteristics of Aluminum/Glass Fiber Composite Laminates
PublicationThe fiber-metal composites made of aluminum sheets and glass fibers reinforced with a polyester resin as the matrix were studied. The composites were prepared by hand lay-up method. Some aspects of manufacturing affecting the composite behavior were considered. In particular, the influences of the arrangement of layers and their number on the mechanical and physical properties of composites with ten different compositions were...
-
Mechanical properties of sisal fiber-reinforced soybean oil-based polyurethane biocomposites
PublicationIn this paper the results of the mechanical properties of polyurethane biocomposites reinforced with short sisal fibers are presented. The fillers were added in different amount: 5, 10 and 15% by mass. Tensile test, hardness, abrasion resistance, elasticity were determined according to the standards.
-
Impact of ultrasounds on physicochemical characteristics of potato tubers
Publication -
Methylene bridged glycoluril dimers: synthetic methods
PublicationZaprezentowano syntezę pochodnych glikolurylu tworzących ściśle sprecyzowane dimeryczne struktury w roztworze wodnym. Opisano diastereoselektywną syntezę pochodnych o strukturze amfifilowej.
-
Low-Cost Surrogate Models for Microwave Filters
PublicationA novel low-cost kriging-based multivariable parametric macromodeling technique for microwave filters is presented. Kriging is used to model both the residues and poles of a microwave filter's reflection coefficient, and the zeros of the transmission coefficient. The proposed residue-pole-zero (RPZ) technique is demonstrated to efficiently model a high dimensional (8D) microwave filter with pseudoelliptic characteristics.
-
Zero-Pole Space Mapping for CAD of Filters
PublicationIn this paper, we propose a new space-mapping technique tailored to the CAD of microwave filters. The goal of space mapping is to achieve a satisfactory design with the minimal number of fine model evaluations. In our approach, the filter is represented by a rational function. To quickly align the coarse and fine models, and to speed up the direct optimization of the coarse model, we propose matching the zeros and poles of a rational...
-
Treatment of malodorous air in biotrickling filters: A review
PublicationOdour nuisance, resulting mainly from the presence of the compounds containing osmophore group and characterized by low olfactory threshold, is associated with danger and may be the cause of negative psychosomatic symptoms. Among different methods of malodorous air treatment, biological methods are of importance, mainly due to reduced operating costs, high purification efficiency of voluminous gas streams characterized by low concentrations...
-
A New Approach to Stability Evaluation of Digital Filters
PublicationIn this paper, a new numerical method of evaluating digital filter stability is presented. This approach is based on novel root-finding algorithms at the complex plane using the Delaunay triangulation and Cauchy's Argument Principle. The presented algorithm locates unstable zeros of the characteristic equation with their multiplicities. The proposed method is generic and can be applied to a vast range of systems. Verification of...
-
Fibre Optic Probes For Ophthalmology
Publication -
Optical Fibre Technology In Poland
Publication -
Fibre-Optic pH Sensor
Publication -
Optical Fibre Technology - A Digest
Publication -
Automatic tagging of musical files
PublicationCelem niniejszej pracy jest zbadanie możliwości automatycznego tagowania utworów muzycznych z wykorzystaniem systemu śledzenia punktu fiksacji wzroku użytkownika. Badania przeprowadzono z udziałem dwudziestu osób o różnym doświadczeniu muzycznym. Zadaniem badanej osoby było wskazanie odpowiedzi na pytania zawarte w ankiecie internetowej, która pozwala na określenie cech utworów muzycznych, takich jak: tempo, dynamika, gatunek....
-
The new silica-based coated SPME fiber as universal support for the confinement of ionic liquid as an extraction medium
PublicationThe new silica-based SPME fiber coating is reported for the first time as universal support purposed to confinement of ionic liquid as an extraction medium. Fiber coating was prepared by the sol-gel process, using potassium silicate (K2SiO3) as a precursor and dimethylformamide (DMF) as a pore-forming medium. The concept of synthesis assumes obtaining a solid porous material on the surface of the glass rod and, being characterized...
-
Impact performance of novel multi-layered prepacked aggregate fibrous composites under compression and bending
PublicationMulti-layered Prepacked aggregate fibrous composite (MLPAFC) is a new type of concrete, which is prepared in two subsequent stages of aggregate-fibre skeleton prepacking and cementitious grouting. In this study, ten MLPAFC mixtures were prepared in three subsequent layers incorporating different contents of four different types of steel fibres. Long and short hooked-end and crimped steel fibers were adopted with 3.0 and 1.5% dosages...
-
Synergistic effect of carbon fibers and carbon nanotubes on improving thermal stability and flame retardancy of polypropylene: a combination of a physical network and chemical crosslinking
Publication -
Influence of transglutaminase or 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide (EDC) on the properties of fish-skin gelatin films
PublicationBadano wpływ sieciowania żelatyny przy użyciu transglutaminazy (TG) lub EDC na rozpuszczalność oraz mechaniczne i barierowe właściwości wytworzonych folii. Rozpuszczalność sieciowanych enzymatycznie folii w buforach o pH 3 i 6 obniżyła się ze 100% do 30%, a folii modyfikowanych TG w obecności ditiotreitolu lub cysteiny, odpowiednio, do 5 i 15%. Rozpuszczalność folii modyfikowanych EDC wynosiła 10%. Sieciowanie enzymatyczne nie...
-
Rearrangeable clos networks C(n,r_1,n^2-1,n,r_2) with certain restrictions for connections
PublicationW pracy została zaproponowana nowa metoda sprawdzania przestrajalności pól Closa dla połączeń jeden do wiele. W rozważaniach zakładamy grupowanie połączeń.In the article we will propose new method of checking rearrangeability of multicast Clos networks. In the literature there is no precise method for checking rearrangeability. We focused on three-stage Clos networks without any constraints about fan-out capability. We show the...
-
Release kinetics and antimicrobial properties of the potassium sorbate-loaded edible films made from pullulan, gelatin and their blends
Publication -
Preparation and characterization of genipin cross-linked porous chitosan–collagen–gelatin scaffolds using chitosan–CO2 solution
PublicationNovel porous scaffolds composed of chitosan, collagen and gelatin were prepared by the multistep procedure involving final freeze-drying and characterized. To eliminate the need for residual acid removal from the material after drying, carbon dioxide saturation process was used for chitosan blend formulation. The use of CO2 for chitosan dissolution made the scaffold preparation process more reproducible and economically sustainable....
-
Polyurethanes modified with natural polymers for medical application. Part II. Polyurethane/gelatin, polyurethane/starch, polyurethane/cellulose
PublicationThis paper is a literature overview of biomedical PUR modifications with natural polymers such as starch, cellulose and gelatin. Properties like biodegradability and biocompatibility of modified PUR cause that these materials may be used as wound dressings, tissue scaffolds, tissue implants and also vascular grafts.
-
Inhibition effect of free ammonia on deammonification process under different intermittent aeration strategies in sequencing batch reactor
PublicationThe deammonification process involves two steps. The first step is the partial nitrification of ammonia (NH4-N) by ammonia oxidizing bacteria (AOB) to produce nitrite (NO2-N) and the second step is the anammox process to “anaerobically” oxidize ammonia to nitrogen gas with nitrite as an electron acceptor (Lackner et al., 2014). Free ammonia (FA) plays a significant role in the stable, long-term deammonification system operation....
-
Aeration Process in Bioreactors as the Main Energy Consumer in a Wastewater Treatment Plant. Review of Solutions and Methods of Process Optimization
PublicationDue to the key role of the biological decomposition process of organic compounds in wastewater treatment, a very important thing is appropriate aeration of activated sludge, because microorganisms have to be supplied with an appropriate amount of oxygen. Aeration is one of the most energy-consuming processes in the conventional activated sludge systems of wastewater treatment technology (may consume from 50% to 90% of electricity...
-
Metal-coated fused silica fibres as a support for immobilized compounds yielding a volatile analyte (C2H4)
PublicationPrzedstawiono wyniki badań dotyczących wykorzystania chemicznie modyfikowanych włókien szklanych pokrytych warstwą metalu (aluminium), jako nośników związków powierzchniowych. W trakcie procesu termicznego rozkładu z tak zmodyfikowanych włókien uwalnia się eten, który stanowi składnik mierzony uzyskiwanej gazowej mieszaniny wzorcowej. Ilość uwalnianego etenu zależy jedynie od długości danego rodzaju i typu modyfikowanego włókna...
-
Submicron inorganic particles as an additional filler in hybrid epoxy matrix composites reinforced with glass fibres
PublicationIn this study, the effect of selected submicron metal oxide (zinc oxide, titanium oxide) or non-metal oxide (silicon dioxide) particles on mechanical and thermo-mechanical properties of epoxy/glass composites was investigated. The applied epoxy resin was a diglycidyl ether of bisphenol-A cured with triethylenetetramine. As a reinforcement twill weave E-glass fabric was used. Hybrid composites (contained particulate and fibrous...
-
Mechanical Performance and Environmental Assessment of Sustainable Concrete Reinforced with Recycled End-of-Life Tyre Fibres
PublicationThe presented research’s main objective was to develop the solution to the global problem of using steel waste obtained during rubber recovery during the tire recycling. A detailed comparative analysis of mechanical and physical features of the concrete composite with the addition of recycled steel fibres (RSF) in relation to the steel fibre concrete commonly used for industrial floors was conducted. A study was carried out using...
-
<title>Technological aspects of fiber optic image guides for needle endoscope manufacturing</title>
Publication -
The structure and mechanical properties of AlMg5Si2Mn alloy after surface alloying by the use of fiber laser
Publication