Search results for: REFINERY EFFLUENTS
-
Design considerations for compact microstrip resonant cells dedicated to efficient branch-line miniaturization
PublicationA conventional compact microstrip resonant cell (CMRC)has been thoroughly investigated to enhance its slow-wave properties and subsequently ensure an efficient miniaturization of a microstrip circuit. The geometry of a classic CMRC has been improved in terms of slowwave effect in two progressive steps: (i) a single-element topology has been replaced with a double-element one and (ii) a high-impedance section has been refined by...
-
Multi-Fidelity Local Surrogate Model for Computationally Efficient Microwave Component Design Optimization
PublicationIn order to minimize the number of evaluations of high-fidelity (“fine”) model in the optimization process, to increase the optimization speed, and to improve optimal solution accuracy, a robust and computational-efficient multi-fidelity local surrogate-model optimization method is proposed. Based on the principle of response surface approximation, the proposed method exploits the multi-fidelity coarse models and polynomial interpolation...
-
Low-Cost Multi-Objective Optimization of Antennas By Means Of Generalized Pareto Ranking Bisection Algorithm
PublicationThis paper introduces a generalized Pareto ranking bisection algorithm for low-cost multi-objective design optimization of antenna structures. The algorithm allows for identifying a set of Pareto optimal sets of parameters (that represent the best trade-offs between considered objectives) by iterative partitioning of the intervals connecting previously found designs and executing a Pareto-ranking-based poll search. The initial...
-
Multiobjective Aerodynamic Optimization by Variable-Fidelity Models and Response Surface Surrogates
PublicationA computationally efficient procedure for multiobjective design optimization with variable-fidelity models and response surface surrogates is presented. The proposed approach uses the multiobjective evolutionary algorithm that works with a fast surrogate model, obtained with kriging interpolation of the low-fidelity model data enhanced by space-mapping correction exploiting a few high-fidelity training points. The initial Pareto...
-
Hybrid constructed wetlands for the National Parks in Poland - a case study, requirements, dimensioning, preliminary results
PublicationWater and wastewater management, especially in rural areas, greatly affects loads of nutrients discharged to the Baltic Sea. In Poland, this management is unbalanced because of the dispersed development and in many locations con struction of sewerage system is uneconomic or even impossible. For this reason, a significant part of sewage from single-family houses in rural areas must be discharged into domestic sewage systems. The...
-
Phototransformation of Amlodipine: Degradation Kinetics and Identification of Its Photoproducts
PublicationNowadays, monitoring focuses on the primary compounds and does not include degradation products formed during various biological and chemical processes. Transformation products may have the same effects to human health and the environment or sometimes they can be more toxic than the parent compound. Unfortunately, knowledge about the formation of degradation products is still limited, however, can be very important for the environmental...
-
A review on recent advances in the application of biosurfactants in wastewater treatment
PublicationMicroorganisms produce a variety of non-conventional surface-active molecules, known as biosurfactants. The biosurfactants find diverse applications in the oil industry, agriculture, emulsifiers, and wastewater treatment, to name a few. Since they are produced from microbes, advantages such as biodegradability, lower toxicity, and environmental compatibility can be leveraged compared to the chemical surfactants. Recently, biosurfactants...
-
Phototransformation of three selected pharmaceuticals, naproxen, 17α-Ethinylestradiol and tetracycline in water: Identification of photoproducts and transformation pathways
PublicationTransformation products (TPs) may be formed during various processes, however, it was proved that one of the main mechanisms responsible for degradation of pharmaceuticals in natural waters is photolysis. Three compounds were selected, tetracycline (TC), 17-α-ethinylestradiol (EE2) and naproxen (NAP), for degradation experiments which were performed using a xenon lamp emitting light with a spectrum closely approximating that of...
-
A Comprehensive Approach to Azo Dichlorotriazine Dye Treatment: Assessing the Impact of Physical, Chemical, and Biological Treatment Methods through Statistical Analysis of Experimental Data
PublicationThis exploration investigates integrated treatment systems combining advanced oxidation processes (Fenton and photo-Fenton) with biological methods for the effective elimination of stubborn organic compounds in simulated textile wastewater composed of azo Dichlorotriazine dye. A comprehensive optimization of key process factors including catalyst dosage, hydrogen peroxide quantity, irradiation duration, etc. was systematically...
-
Sonocatalytic degradation of Bisphenol A from aquatic matrices over Pd/CeO2 nanoparticles: Kinetics study, transformation products, and toxicity
PublicationIn this work, different ratios of palladium – cerium oxide (Pd/CeO2) catalyst were synthesized and characterized, while their sonocatalytic activity was evaluated for the degradation of the xenobiotic Bisphenol A (BPA) from aqueous solutions. Sonocatalytic activity expressed as BPA decomposition exhibited a volcano-type behavior in relation to the Pd loading, and the 0.25Pd/CeO2 catalyst characterized by the maximum Pd dispersion...
-
Rapid on-line method of wastewater parameters estimation by electronic nose for control and operating wastewater treatment plants toward Green Deal implementation
PublicationIn order to comply with legal regulations related to wastewater quality, the operational mode of facilities at wastewater treatment plant (WWTP) should be properly adjusted according to parameters of influents, however it is very difficult without frequently performed measurements. Currently there are known many techniques and devices for assesment of wastewater parameters such as chemical oxygen demand, biochemical oxygen demand,...
-
Design Space Reduction for Expedited Multi-Objective Design Optimization of Antennas in Highly-Dimensional Spaces
PublicationA surrogate-based technique for efficient multi-objective antenna optimization is discussed. Our approach exploits response surface approximation (RSA) model constructed from low-fidelity antenna model data (here, obtained through coarse-discretization electromagnetic simulations). The RSA model enables fast determination of the best available trade-offs between conflicting design goals. The cost of RSA model construction for multi-parameter...
-
Finding the Right Solvent: A Novel Screening Protocol for Identifying Environmentally Friendly and Cost-Effective Options for Benzenesulfonamide
PublicationThis study investigated the solubility of benzenesulfonamide (BSA) as a model compound using experimental and computational methods. New experimental solubility data were collected in the solvents DMSO, DMF, 4FM, and their binary mixtures with water. The predictive model was constructed based on the best-performing regression models trained on available experimental data, and their hyperparameters were optimized using a newly...
-
Structure and paramagnetism in weakly correlated Y8Co5
PublicationWe report the basic physical properties of monoclinic Y8Co5 determined by means of magnetic susceptibility, electrical resistivity, and specific heat measurements. The crystal structure of Y8Co5 is monoclinic (P21/c) with lattice parameters a = 7.0582(6) Å, b = 7.2894(6) Å, c = 24.2234(19) Å, and β = 102.112(6)° as refined by using synchrotron powder x-ray diffraction data. The compound shows temperature independent paramagnetism...
-
Impact assessment culture in the European Union. Time for something new?
PublicationCurrent approaches and cultures for the economic evaluations of environmental and health policies may suffer from excessive reliance on a standard neoclassic economic toolbox that neglects alternative perspectives. This may prematurely limit the spectrum of available policy options. Here we show how the inclusion of neglected currents of thought such as non-Ricardian economics, bioeconomics and a set of qualitative-quantitative...
-
A strong preference for the TA/TA dinucleotide step discovered for an acridine-based, potent antitumor dsDNA intercalator, C-1305: NMR-driven structural and sequence-specificity studies
PublicationTriazoloacridinone C-1305, a potent antitumor agent recommended for Phase I clinical trials, exhibits high activity towards a wide range of experimental colon carcinomas, in many cases associated with complete tumor regression. C-1305 is a well-established dsDNA intercalator, yet no information on its mode of binding into DNA is available to date. Herein, we present the NMR-driven and MD-refined reconstruction of the 3D structures...
-
Influence of the boron doping level on the electrochemical oxidation of raw landfill leachates: advanced pre-treatment prior to the biological nitrogen removal
PublicationThe electrochemical oxidative treatment of landfill leachates (LLs) containing high amounts of ammonia nitrogen and organic matter was used as a promising method, prior to biological processes, to achieve the final effluent quality that would be acceptable by current regulations. The deposited boron-doped diamond electrodes (BDDs) with different boron doping concentrations (10000, 5000 and 500 ppm of B) were applied as anodes....
-
Sequential treatment of landfill leachate by electrocoagulation/aeration, PMS/ZVI/UV and electro-Fenton: Performance, biodegradability and toxicity studies
PublicationThis study presents a systematic study on sequential treatment of highly resistant landfill leachate by electrocoagulation (EC)/aeration, sulfate radical advanced oxidation process (SR-AOP) and electro-Fenton (EF). In case of SR-AOP, peroxymonosulfate (PMS) catalyzed by zero valent iron (ZVI) and ultraviolet irradiation (UV) system was developed. Treatment process was optimized in respect to COD removal. Analysis of results revealed...
-
An Overview of Treatment Approaches for Octahydro-1, 3, 5, 7-tetranitro-1, 3, 5, 7-tetrazocine (HMX) Explosive in Soil, Groundwater, and Wastewater
PublicationOctahydro-1, 3, 5, 7-tetranitro-1, 3, 5, 7-tetrazocine (HMX) is extensively exploited in the manufacturing of explosives; therefore, a significant level of HMX contamination can be encountered near explosive production plants. For instance, up to 12 ppm HMX concentrations have been observed in the wastewater effluent of a munitions manufacturing facility, while up to 45,000 mg/kg of HMX has been found in a soil sample taken from...
-
The Simulation of Activated Sludge System for Optimization of Predictive Aeration at Large WWTP
PublicationEffective use of biodegradable substrates as an internal carbon sources (ICS) for denitrification and EBPR and predicting performance of aeration systems during nitrification in activated sludge bioreactors, may be useful in realization the sustainable development by potentially saving energy consumption at WWTPs. A large number of WWTPs use activated sludge systems with an integrated removal of carbon, nitrogen and phosphorus...
-
DETERMINATION OF SURFACTANTS IN ENVIRONMENTAL SAMPLES - PART I. CATIONIC COMPOUNDS = Oznaczanie Surfaktantów W Próbkach Środowiskowych. Część I. Związki Kationowe
PublicationCompounds from the group of cationic surfactants are widely applied in household, industrial, cleaning, disinfectant, cosmetic and pharmaceutical products as their specific properties (antimicrobial, emulsifying, anticorrosion, softening). After use, cationic surfactants are disposed to wastewater-treatment plants and finally with effluent water to surface waters due to their incomplete degradation. Moreover, they can freely circulate...
-
Computationally Efficient Multi-Objective Optimization of and Experimental Validation of Yagi-Uda Antenna
PublicationIn this paper, computationally efficient multi-objective optimization of antenna structures is discussed. As a design case, we consider a multi-parameter planar Yagi-Uda antenna structure, featuring a driven element, three directors, and a feeding structure. Direct optimization of the high-fidelity electromagnetic (EM) antenna model is prohibitive in computational terms. Instead, our design methodology exploits response surface...
-
A hybrid approach to optimization of radial inflow turbine with principal component analysis
PublicationEnergy conversion efficiency is one of the most important features of power systems as it greatly influences the economic balance. The efficiency can be increased in many ways. One of them is to optimize individual components of the power plant. In most Organic Rankine Cycle (ORC) systems the power is created in the turbine and these systems can benefit from effective turbine optimization. The paper presents the use of two kinds...
-
New hybrid quadrature schemes for weakly singular kernels applied to isogeometric boundary elements for 3D Stokes flow
PublicationThis work proposes four novel hybrid quadrature schemes for the efficient and accurate evaluation of weakly singular boundary integrals (1/r kernel) on arbitrary smooth surfaces. Such integrals appear in boundary element analysis for several partial differential equations including the Stokes equation for viscous flow and the Helmholtz equation for acoustics. The proposed quadrature schemes apply a Duffy transform-based quadrature...
-
Seismic damage diagnosis in adjacent steel and RC MRFs considering pounding effects through improved wavelet-based damage-sensitive feature
PublicationThis paper aims to propose complex Morlet (cmorfb-fc) wavelet-based refined damage-sensitive feature (rDSF) as a new and more precise damage indicator to diagnose seismic damages in adjacent steel and Reinforced Concrete (RC) Moment Resisting Frames (MRFs) assuming pounding conditions using acceleration responses. The considered structures include 6- and 9-story steel and 4- and 8-story RC benchmark MRFs that are assumed to have...
-
A Surrogate-Assisted Measurement Correction Method for Accurate and Low-Cost Monitoring of Particulate Matter Pollutants
PublicationAir pollution involves multiple health and economic challenges. Its accurate and low-cost monitoring is important for developing services dedicated to reduce the exposure of living beings to the pollution. Particulate matter (PM) measurement sensors belong to the key components that support operation of these systems. In this work, a modular, mobile Internet of Things sensor for PM measurements has been proposed. Due to a limited...
-
Instrumented end notched flexure - Crack propagation and process zonemonitoring Part II: Data reduction and experimental
PublicationA mode II instrumented end notched flexure three point bending (ENF) adhesion test is described. The adhesive joint consists of two aluminium alloy (AW7075-T6) plates bonded with a structural epoxy adhesive (Hysol EA 9395™). Strain gauges are attached to the outer surface (backface) of the substrates in the lengthwise direction to measure local surface strain during crack propagation. Simultaneously, load/displacement measurements...
-
The Implementation of Fuzzy Logic in Forecasting Financial Ratios
PublicationThis paper is devoted to the issue of forecasting financial ratios. The objective of the conducted research is to develop a predictive model with the use of an innovative methodology, i.e., fuzzy logic theory, and to evaluate its effectiveness. Fuzzy logic has been widely used in machinery, robotics and industrial engineering. This paper introduces the use of fuzzy logic for the financial analysis of enterprises. While many current...
-
Multi-Taper-Based Automatic Correction of Non-Anechoic Antenna Measurements
PublicationPrototype measurements belong to the key steps in the development of antenna structures. Although accurate validation of their far-field performance can be realized in dedicated facilities, such as anechoic chambers, the high cost of their construction and maintenance might not be justified if the main goal of measurements is to support teaching or low-budget research. Instead, they can be performed in non-anechoic conditions and...
-
An image processing approach for fatigue crack identification in cellulose acetate replicas
PublicationThe cellulose acetate replication technique is an important method for studying material fatigue. However, extracting accurate information from pictures of cellulose replicas poses challenges because of distortions and numerous artifacts. This paper presents an image processing procedure for effective fatigue crack identification in plastic replicas. The approach employs thresholding, adaptive Gaussian thresholding, and Otsu binarization...
-
Indirect Determination of MCPD Fatty Acid Esters in Lipid Fractions of Commercially Available Infant Formulas for the Assessment of Infants’ Health Risk
PublicationMCPD esters are intensively investigated food lipid contaminants for over a decade. Concern related to their presence in various types of food products is related to the fact that possible free MCPD release from its esterified form during digestion may lead to elevated daily intake of these toxicants.Special attention should be devoted into powdered infant formulas, which contain significant amounts of refined vegetable oils, likely...
-
Protection and viability of fruit seeds oils by nanostructured lipid carrier (NLC) nanosuspensions
PublicationIn this paper, we focused on the development of nanostructured lipid carriers (NLCs) for dermal application. The NLC matrix was designed as a protective reservoir of biological active compounds that naturally occur in domestic fruit seed oils. Over the years, emulsions, as a popular physicochemical form of personal care products, were refined in order to obtain the best possible penetration into the skin of any bioactive compound...
-
A total scoring system and software for complex modified GAPI (ComplexMoGAPI) application in the assessment of method greenness
PublicationEvaluating analytical methods with innovative metrics is essential to ensure the effectiveness of analytical procedures. Various approaches have been proposed to assess the performance of an analytical method and its environmental consequences, as sustainable environment and green chemistry ideology are of high importance nowadays. Considering greenness evaluation of developed analytical procedures, Green Analytical Procedure Index...
-
Superconductivity in a breathing kagome metals ROs2 (R = Sc, Y, Lu)
PublicationWe have successfully synthesized three osmium-based hexagonal Laves compounds ROs2 (R = Sc, Y, Lu), and discussed their physical properties. LeBail refinement of pXRD data confirms that all compounds crystallize in the hexagonal centrosymmetric MgZn2- type structure (P63/mmc, No. 194). The refined lattice parameters are a = b = 5.1791(1) Å and c = 8.4841(2) Å for ScOs2, a = b = 5.2571(3) Å and c = 8.6613(2) Å for LuOs2 and a =...
-
Efficient Simulation-Based Global Antenna Optimization Using Characteristic Point Method and Nature-Inspired Metaheuristics
PublicationAntenna structures are designed nowadays to fulfil rigorous demands, including multi-band operation, where the center frequencies need to be precisely allocated at the assumed targets while improving other features, such as impedance matching. Achieving this requires simultaneous optimization of antenna geometry parameters. When considering multimodal problems or if a reasonable initial design is not at hand, one needs to rely...
-
Human-associated bacteria and their mobile genetic elements - important minority in wastewater and wastewater impacted ecosystems
PublicationSince human-associated bacteria have been recognized as vectors in two - way gene transmission between the pathogenic and environmental populations, health hazard connected with wastewater discharge requires reevaluation. In this paper the particular attention was given to antimicrobial-resistance of Escherichia coli and enterococci isolated from wastewater and wastewater impacted environments. The obtained results showed that...
-
Elucidation of transformation pathway of ketoprofen, ibuprofen, and furosemide in surface water and their occurrence in the aqueous environment using UHPLC-QTOF-MS
PublicationThe identification and determination of transformation products (TPs) of pharmaceuticals is essential nowadays, in order to track their fate in the aqueous environment and, thus, to estimate the actual pollution. However, this is a challenging task due to the necessity to apply high-resolution instruments enable to detect known and unknown compounds. This work presents the use of liquid chromatography quadrupole time-of-flight...
-
Treated wasetewater as a source of humic substances in surface waters
PublicationHumic substances impose substantial effect on the aquatic environment as well as the water organisms and human health. Among other features, the humic acids determine organoleptic properties of surface waters. Therefore explanation of the origin and properties of humic acids in surface waters is one of the priorities of water technology.Recently it was pointed out that in the wastewater treatment process organic compounds characterized...
-
Sustainable recovery of plant essential Nitrogen and Phosphorus from human urine using industrial coal fly ash
PublicationCoal-based thermal power plants play a pivotal role in meeting global energy demand. The amount of fly ash generated from these plants increases every year, and its successful use has posed a significant environmental risk in the last decade. In this study, coal fly ash was packed in a fixed-bed adsorption column to remove Urea–N from synthetic human urine. To assess the efficacy of fly ash in the removal of Nitrogen, various process...
-
Improving the energy balance in wastewater treatment plants by optimization of aeration control and application of new technologies
PublicationThe methods to improve the energy balance of a wastewater treatment plant (WWTP) by optimization of aeration process control and application of innovative nitrogen removal technologies were overviewed in the study. The control of aeration based on the ABAC (Ammonia-Based Aeration Control) system allows not only for significant savings in electricity consumption, but it can also increase the efficiency of the denitrification process....
-
Modelling of Different Aeration Modes Influencing Processes in SBR Bioreactor
PublicationCurrently, computer modelling together with the simulation tools tailored for that purpose constitute a very important element in planning technological changes within wastewater treatment plant. From the point of view of the WWTP operator every modification should be introduced in order to improve the quality of treated sewage with the lowest financial outlays. These requirements can be met by using computer programmes to effectuate...
-
Efficiency of pollutants removal from landfill leachates using Nb/BDD and Si/BDD anodic oxidation
PublicationLandfill leachates (LLs) is a complex, refectory and difficult to depurate liquid generated from sanitary landfills. It contains excessive levels of biodegradable and in particular non-biodegradable products (e.g. heavy metals, phenols, sulphide, plasticisers). LLs are among the effluents that may pose major environmental concerns, they can be a dangerous source of pollution e.g. due to infiltration into soil and underlying water....
-
A selection of the optimal eluent components for separation of carnivorous plants metabolites by planar chromatography chromatography
PublicationAbstract: The development of the new procedures of the separation components with the complicated chemical structure from natural complex matrix by column chromatography is very difficult and in many cases expensive. Therefore to pre-select the conditions of the separation process the use of thin layer chromatography (TLC) is proffered. The possibility of proceeding the chromatographic process for several mixtures on single plate,...
-
eFRADIR: An Enhanced FRAmework for DIsaster Resilience
PublicationThis paper focuses on how to increase the availability of a backbone network with minimal cost. In particular, the new framework focuses on resilience against natural disasters and is an evolution of the FRADIR/FRADIR-II framework. It targets three different directions, namely: network planning, failure modeling, and survivable routing. The steady state network planning is tackled by upgrading a sub-network (a set of links termed...
-
Thermo-Mechanical Simulation of Underwater Friction Stir Welding of Low Carbon Steel
PublicationThis article investigates the flow of materials and weld formation during underwater friction stir welding (UFSW) of low carbon steel. A thermo-mechanical model is used to understand the relation between frictional heat phenomena during the welding and weld properties. To better understand the effects of the water environment, the simulation and experimental results were compared with the sample prepared by the traditional friction...
-
Application of shifted Chebyshev polynomial-based Rayleigh–Ritz method and Navier’s technique for vibration analysis of a functionally graded porous beam embedded in Kerr foundation
PublicationPresent study is dealt with the applicability of shifted Chebyshev polynomial based Rayleigh-Ritz method and Navier’s technique on free vibration of Functionally Graded (FG) beam with uniformly distributed porosity along the thickness of the beam. The material properties such as Young’s modulus, mass density, and Poisson’s ratio are also considered to vary along the thickness of the FG beam as per the power-law exponent model....
-
Generalized Pareto ranking bisection for computationally feasible multi-objective antenna optimization
PublicationMulti-objective optimization (MO) allows for obtaining comprehensive information about possible design trade-offs of a given antenna structure. Yet, executing MO using the most popular class of techniques, population-based metaheuristics, may be computationally prohibitive when full-wave EM analysis is utilized for antenna evaluation. In this work, a low-cost and fully deterministic MO methodology is introduced. The proposed generalized...
-
Cost-Efficient Multi-Objective Design of Miniaturized Microwave Circuits Using Machine Learning and Artificial Neural Network
PublicationDesigning microwave components involves managing multiple objectives such as center frequencies, impedance matching, and size reduction for miniaturized structures. Traditional multi-objective optimization (MO) approaches heavily rely on computationally expensive population-based methods, especially when exe-cuted with full-wave electromagnetic (EM) analysis to guarantee reliability. This paper introduces a novel and cost-effective...
-
Spotkanie naukowe w ramach Rethinking Economics Gdańsk
EventsProfesor Erik S. Reinert wygłosi wykład na temat: "What causes economic development to be so uneven between countries? Theoretical and Historical Perspectives." 18 marca 2021, o godz. 18:00 na platformie Zoom.
-
Assessment of River Water Quality and Pollution Status Using Physicochemical and Biometrics, Awetu River, Ethiopia
PublicationThe surface water is contaminated by a variety of synthetic organic and inorganic compounds, chemicals, and nutrients; due to this reason, the quality of the water resources of Ethiopia is declining at an alarming rate, resulting in severe environmental degradation. The main objective of the study was to recognize the pollution status river for the study area by physicochemical parameters and the extent of microbial environmental...