Filtry
wszystkich: 7924
wybranych: 6337
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: DESTROYED JOINTS, WELDED JOINTS, STEEL STRUCTURE, ACCELERATIONS, EARTHQUAKES, SHAKING TABLE TESTS
-
Influence of the laser remelting parameters on the thickness of surface layers created on the stainless steel X5CrNi18-10
PublikacjaIn this work the surface of austenitic stainless steel type X5CrNi18-10 was treated by using laser. Laser remelting was done by means of laser MLT 2500 CO2 with different parameters of treatment: P - power beam (800 [W], 1000 [W], 1100 [W], 1200 [W]); v - scanning velocity (6 [mm/s], 7 [mm/s], 8 [mm/s]); diameter of laser beam (1.4 [mm], 1.6 [mm]). The influence of these parameters on the thickness and shape of layers in manufacturing...
-
Bead-on-plate welding on S235JR steel by underwater local dry chamber process
PublikacjaThe article presents the results of the effect of parameters of underwater local dry chamber welding on the properties of padding welds. The effect of heat input and the type of shielding gas on the structure and hardness of welds was established. the functions for estimating the maximum hardness of the heat affected zone have been also elaborated.
-
The Influence of the Depth of Cut in Single-Pass Grinding on the Microstructure and Properties of the C45 Steel Surface Layer
PublikacjaThe paper contains the results of a metallographic examination and nanoindentation test conducted for the medium carbon structural steel with low content of Mn, Si, Cu, Cr, and Ni after its grinding to a depth ranging from 2 μm to 20 μm, at constant cutting speed (peripheral speed) of vs = 25 ms−1 and constant feed rate of vft = 1 m/min. Applied grinding parameters did not cause the surface layer hardening, which could generate...
-
STRUCTURE AND ALGORITHMS OF A DIAGNOSTIC DEVICE IN A WHEELED TRACTOR
PublikacjaDiagnostic device monitors the tractor’s technical condition and identifies the location of damaged components during operation. The diagnostic device detects and identifies the following types of defects: functional defects (uf) which affect performance, exhaust defects (ue) which increase toxic emissions and fuel consumption, defects that jeopardize driving safety (us), defects that affect engine performance (ud). The key component...
-
Verification of algorithms determining wave loads on support structure of wind turbine
PublikacjaThe offshore wind turbines require determination of wave loads on their support structure. This structure is fixed and, therefore, this problem is reduced to solving only the diffraction problem, which is determined by Laplace equation and conditions on the following boundaries: on the support structure, on the sea free surface and on its bottom, and at infinity on free surface. The linear problem was applied to determine the wave...
-
Application of the fluid–structure interaction technique for the analysis of hydrodynamic lubrication problems.
PublikacjaFluid–structure interaction technique seems to be one of the most promising possibilities for theoretical analysis of lubrication problems. It allows coupling of different physical fields in one computational task, taking into account the interaction between them. In this article, two sets of fluid–structure interaction analyses focusing on the bearing performance evaluation are presented. One analysis was applied to a water-lubricated...
-
Mathematical Models of Control Systems of Angular Speed of Steam Turbines for Diagnostic Tests of Automatic and Mechatronic Devices
PublikacjaAccurate modeling of physical processes of many automatics and mechatronics systems is often necessity. In power system such a process is control of angular velocity of power objects during connection to operation in parallel. This process is extremely dynamic. For this reason response of control system depends from changes of many physical parameters (temperature, pressure and flow of the medium, etc.). Precision modeling influences...
-
Effective yttrium based coating for steel interconnects of solid oxide cells: Corrosion evaluation in steam-hydrogen atmosphere
PublikacjaThis work describes manufacture, analysis and test of a new well conducting corrosion-protection coating that can be applied on steel types with high chromium content. Electrolytic deposition of yttrium salts is used to form thin (<100 nm) coatings on both flat steel sheets (material: Crofer 22 APU) and its properties are proven on woven wire-meshes (materials from two different sources: SUS316 and SUS316L). The oxide scale on...
-
An enhanced method in predicting tensile behaviour of corroded thick steel plate specimens by using random field approach
PublikacjaThe present work investigates the possibility of using random field techniques in modelling the mechanical behaviour of corroded thick steel plate specimens. The nonlinear Finite Element method, employing the explicit dynamic solver, is used to analyse the mechanical properties of typical specimens. A material model considering full nonlinearity is used to evaluate the stress-strain response. The influence of major governing parameters...
-
Effects of Column Base Flexibility on Seismic Response of Steel Moment-Frame Buildings
PublikacjaSteel Moment Resisting Frames (SMRFs) are very popular lateral load resisting systems in many seismically active regions. However, their seismic response is strongly dependent on the rotational fixity of column base connections. Despite many studies (both experimental and numerical) in this particular area, available approaches for estimating column base flexibility have been validated only against laboratory test data. In the...
-
The influence of applying supplementary web plates on structural joint moment resistance and rotational stiffness
PublikacjaContinual trend to simplify structural elements and find less time-consuming solutions on construction site as well as inevitable increase in labour costs determine for instance elimination of those technological steps that are difficult to automation. Welding additional reinforcements and web stiffeners is a great example of such a step. The method presented in EN 1993-1-8 [8] is a result of long-term studies focused on calculating...
-
Fracture surface topography investigation and fatigue life assessment of notched austenitic steel specimens
PublikacjaThe objectives of this study were to investigate the fracture surface topography of X8CrNiS18-9 austenitic stainless-steel specimens for different loadings and notch radii and to supplement the knowledge about the fracture mechanisms for fatigue performance. Cases with three different values of the notch radius ρ and the stress amplitude σa were analysed. The fracture topographies were quantified by the areas over their entire...
-
The Performance of ASON/GMPLS Network with Hierarchical Control Plane Structure
PublikacjaThe paper regards the problem of ASON/GMPLS network performance with hierarchical control plane structure in condition of incomplete domain network information. The authors propose the hierarchical ASON/GMPLS control plane architecture, which fulfills the requirements of modern optical networks and allows to control the multidomain network with requirement quality of service. The authors examine the scalability and properties of...
-
Subsoil degradation effect in reliability analysis of the jack-up platform structure
PublikacjaStructural reliability analysis is considered, by FORM and SORM applied to a certain idealized soil-platform structure interaction problem due to cyclic water wave and wind loads. Wave and wind loads are random variables, whereas dead load is deterministic. Load parameters are typical for storm conditions in the Baltic Sea. The soil-structure interaction is idealized as a set of linear translational and rotational springs. Due...
-
The effect of Sr and Mg substitutions on structure, mechanical properties and solubility of fluorapatite ceramics for biomedical applications
PublikacjaIonic substitutions play important role in the modifications of biological apatites. Recently, attention has been focused on the co-doping effects on the functional properties of apatite-based biomaterials. In this research work, the dense samples of fluorapatites, Ca10(PO4)6F2 and Ca8MgSr(PO4)6F2, were produced after sintering at 1250 °C for 6 h in air. Structural characterization carried out with XRD, IR, Raman and SEM, confirmed...
-
Low temperature deposition of dense MnCo 2 O 4 protective coatings for steel interconnects of solid oxide cells
PublikacjaIn this work manganese cobalt spinel (MnCo2O4) coatings were deposited on steel substrates by spray pyrolysis at 390 °C. This is at much lower temperatures than previously reported (typically in excess of 900 °C). It was possible to produce coatings with well controlled thickness (2-5-10 μm). The as-deposited coatings were evaluated for their microstructural changes and electrical conductivity up to 800 °C. Results confirm the...
-
Selected problems of stability of steel structures.
PublikacjaW pracy przedstawiono wyniki badań dotyczących stateczności wybranych konstrukcji stalowych. Prezentowane rozważania są oparte na klasycznych założeniach teorii prętów cienkościennych o nieodkształcalnym przekroju poprzecznym. Wyznaczono pierwszą wariację sił krytycznych pręta cienkościennego o bisymetrycznym otwartym przekroju poprzecznym uwzględniając następujące zmienne projektowe: ⎯wymiary przekroju poprzecznego, ⎯ charakterystyki...
-
The Structure of Entrepreneurial Team Members’ Competencies: Between Effectuation and Causation
PublikacjaA conscious shaping of entrepreneurial competence is a relevant element of entrepreneurial education. In order to recognize which of the competencies regarded as entrepreneurial are characteristic of members of entrepreneurial teams, which is crucial for the work of those teams, it is necessary to identify the structure of those competencies. This quantitative study was conducted with the use of a survey method and involved 111...
-
High-temperature kinetics study of 430L steel powder oxidized in air at 600–850 °C
PublikacjaThe 430L stainless steel powder with a mean particle size of 95 μm was studied to determine its high-temperature oxidation properties. Continuous thermogravimetric measurements were carried out for 100 h in air at temperatures in the range of 600–850 °C. Even though a considerable amount of Cr (up to ˜5 wt.% Cr) inside the grains was depleted – especially inside small grains – no breakaway oxidation was observed. This indicates...
-
Determination of moisture resistance of covered electrodes according to PN-EN ISO 14372
PublikacjaMoisture present in the electrode covering is one of the sources of diffusible hydrogen in welded joints. In order to study the diffusible hydrogen content in deposited metal, a stand for moisturizing covered electrodes, in accordance with the PN-EN ISO 14372 standard, was built. After the stand was completed, a test of moisturizing the electrodes was carried out and measurements of the diffusible hydrogen content in deposited...
-
DESIGN AND STRENGTH CALCULATIONS OF THE TRIPOD SUPPORT STRUCTURE FOR OFFSHORE POWER PLANT
PublikacjaThe support structure being the object of the analysis presented in the article is Tripod. According to the adopted assumptions, it is a foundation gravitationally set in the water region of 60 m in depth, not fixed to the seabed, which can be used for installing a 7MW wind turbine. Due to the lack of substantial information on designing and strength calculations of such types of structures in the world literature, authors have...
-
Fuctional structure of diagnostic system for wheeled tractors
PublikacjaAn application of computer controlled fuel injection systems in vehicle engines and growing demands concerning toxic substances emission and fuel consumption was a main reason for OBD (On Board Diagnosis) development. In spite of a great technological development, only some tractors are equipped in diagnostic systems. On board diagnosis is strongly connected with emission demands and does not concern other important vehicle functions.In...
-
MECHANICAL PROPERTIES OF BOTTOM ASH – DREDGED MATERIAL MIXTURES IN LABORATORY TESTS
PublikacjaBottom ash from EC Gdańsk and dredged material taken from the mouth of The Vistula were mixed to form an engineering material used for dike construction. Mixtures with different bottom ash content were tested in laboratory to determine its basic physical and mechanical properties. The optimum bottom ash–dredged material mixture, built in the corps of the test dike, contains 70% of ash. The optimum bottom ash content in the mixture...
-
Experimental tests results of the diode rectifier with series active power filter
Publikacja -
The Comparison of the Emissions from Light Duty Vehicle in On-road and NEDC Tests
Publikacja -
Reliability of UAVs in Fire Services Operations. Tests and Measurements of Selected Parameters
Publikacja -
Lamb Wave Based Structural Damage Detection Using Stationarity Tests
Publikacja -
Badania międzylaboratoryjne w chemii analitycznej. Interlaboratory tests in analytical chemistry.
PublikacjaW pracy dokonano podziału dostępnych badań międzylaboratoryjnych w zależności od założonego celu badań. Przedstawiono i scharakteryzowano podstawowe typy programów badań międzylaboratoryjnych oraz aspekt ich organizacji. Omówiono również wykorzystanie badań biegłości/porównań międzylaboratoryjnych w procesach akredytacji i nadzoru laboratoriów oraz możliwy sposób obróbki danych nadesłanych przez uczestników badań.
-
Characterization of aggregate interlocking in hot mix asphalt by mechanistic performance tests
Publikacja -
Verification of geotechnical numerical simulations by model tests using PIV technique
PublikacjaPrzedstawiono metodykę i wyniki badań modelowych stateczności fundamentów bezpośrednich posadowionych w sąsiedztwie kątowych ścian oporowych. Dla takiego złożonego układu fundament - obciążenie - podłoże gruntowe wykonano badania modelowe w płaskim stanie odkształcenia na gruncie naturalnym i analogowym. Trajektorie i izopola przemieszczeń oraz progresywny rozwój kształtu i zasięgu powierzchni poślizgu określono techniką PIV.
-
Tests on lateral resistance in railway track during operation of tamping machine
PublikacjaArtykuł prezentuje koncepcję prowadzenia badań oporów poprzecznych w trakcie procesu regulacji geometrycznej toru kolejowego za pomocą podbijarki. Jest to zatem kontynuacja badań nad zastosowaniem podbijarki torowej w diagnostyce toru bezstykowego; wcześniej zajmowano się kwestią określania sił podłużnych w szynach. Przedstawiono sposób wyznaczania oporów poprzecznych polegający na ciągłej rejestracji przemieszczenia oraz siły...
-
The assessment of load-settlement curve for Atlas piles correlated with CPT tests
PublikacjaRacjonalne stosowanie pali przemieszczeniowych typu Atlas wymaga analitycznej oceny pełnej krzywej obciążenie - osiadanie. W pracy przedstawiono możliwości wykorzystania metody funkcji transformacyjnych t-z (dla pobocznicy) oraz q-z (dla podstawy) dla oceny krzywej osiadania. Jednostkowe graniczne opory na pobocznicy, tmax, oraz pod podstawą, gf, określono na podstawie metody bezpośredniej, wykorzystując opory stożka sondy, qc....
-
The basics of design and experimental tests of the commutation unit of a hydraulic satellite motor
Publikacjahe article presents an analytical method to design the commutation unit in a hydraulic satellite motor. It is shown that the size of the holes feeding the working chambers and their location on the plates closing those chambers depends on the geometrical dimensions of the working mechanism. The overlap in the commutation unit depends on the rotational speed range. It is demonstrated that the geometrical dimensions of the commutation...
-
Application of linear buckling sensitivity analysis to economic design of cylindrical steel silos composed of corrugated sheets and columns
PublikacjaThe paper deals with global stability of steel cylindrical silos composed of corrugated walls and vertical columns with loads imposed by a bulk solid following Eurocode 1. The optimum silo design with respect to the steel weight was based on a sensitivity analysis method. The changes of silo column profiles at each design step were performed by means of influence lines for the buckling load factor due to the unit column bending...
-
Electronic structure of CeBa2Cu3O7.
PublikacjaPrzeprowadzono obliczenia ab initio struktury elektronowej związku CeBa2Cu3-O7(Ce123) metodą LAPW oraz porównano z analogicznymi strukturami otrzymanymi dla YBa2Cu3O7 (Y123), NdBa2Cu3O7(Nd123) i PrBa2Cu3O7(Pr123). Wszystkie wyliczone struktury pasmowe są zasadniczo podobne. W pracy postawiono hipotezę dotyczącą korelacji pomiędzy silnym rozszczepieniem spinowym w Pr123 i Ce123a niestabilnością strukturalną tych układów.
-
Fatigue of the ship structure.
PublikacjaZaprezentowano wyniki prac badawczych zachowania paneli SANDWICH pod obciążeniem zginającym. Prace prowadzone były w Kat. Technol. Okrętów i Obiektów Oceanotechn. Wydz. OiO i obejmowały między innymi badania konstrukcji w skali rzeczywistej. Dokonano porównania uzyskanych rezultatów z wynikami prezentowanymi w literaturze.
-
The structure of nystatin A2
PublikacjaBudowa chemiczna składnika kompleksu nystatyn (nystatyny A2) została ustalona na podstawie analizy estru metylowego N-acetylonystatyny A2 przy pomocy metod spektroskopowych UV, MS i NMR. Widmo UV wskazało obecność w badanym związku chromoforu tetraenowego. Ciężar cząsteczkowy ustalono jako 909 j.m. na postawie analizy MS z wykorzystaniem techniki FAB, co pozwoliło wydedukować skład elementarny nystatyny A2 jako C47H75NO16. Analizy...
-
Electronic structure of TbBa2Cu3O7
PublikacjaW pracy wykonano obliczenia kwantowomechaniczne struktury elektronowej hipotetycznego materiału TbBa2Cu3O7 (Dy123) metodą FP-LAPW (full potential - linearized augmented plane wave) w ramach formalizmu DFT (density functional theory) stosując przybliżenie GGA (generalized gradient approximation). Ze względu na silne oddziaływania korelacyjne elektronów 4f w atomie Tb zastosowano dodatkowo poprawkę kulombowską U w ramach modelu...
-
Quasistatic and fatigue behavior of an AISI H13 steel obtained by additive manufacturing and conventional method
PublikacjaThis work aims to compare the mechanical behavior of an AISI H13 steel obtained by additive manufacturing with that obtained by conventional manufacturing methods. The average values of the ultimate tensile strength (UTS) and ductility obtained for the specimens produced by the conventional method were equal to 658 MPa and 18%, respectively, which compares with 503 MPa and 0.75% registered for the selective laser melting (SLM)...
-
Variable-structure algorithm for identification of quasi-periodically varying systems
PublikacjaThe paper presents a variable-structure version of a generalized notchfiltering (GANF) algorithm. Generalized notch filters are used for identification of quasi-periodically varying dynamic systems and can be considered an extension, to the system case, of classical adaptive notch filters. The proposed algorithm is a cascade of two GANF filters: a multiple-frequency "precise" filter bank, used for precise system tracking, and a...
-
Reconstruction of 3D structure of positive corona streamer by local methods
PublikacjaThe computer algorithms were used for reconstruction of streamer 3D structure. We propose the 3D tree structure model of corona discharge streamer composed with nodes and edges between chosen couples of nodes, which enables easy computation of some important parameters ofstreamers. The 3D model can be derived directly from two projection images by global methods like evolutionary searching or particle simulations. In this paper...
-
Formation of Porous Structure of the Metallic Materials Used on Bone Implants
PublikacjaResearch on improvement of structure and fabrication methods of the bone implants are carried out for many years. Research are aimed to shape the structures, that will have a Young's modulus value similar to the value of the human bones Young's modulus. Depending on theporosity, Young's moduli can even be tailored to match the modulus of bone closer than solid metals can, thus reducing the problems associated with stress shielding...
-
The changes of crosslink density of polyurethanes synthesised with using recycled component. Chemical structure and mechanical properties investigations.
PublikacjaThis paper aims at the utilisation of glycerolysate (Gly) obtained in polyurethane recycling process by means of crude glycerine, which has in its structure hydroxyl end groups that allow for further processing. Polyurethanes (PUs) were synthesised using prepolymer method with the mixture of neat polyol and glycerolysate, in different ratios, with 4,4-diphenylmethane diisocyanate (MDI). The prepolymer was subsequently extended...
-
Cross-sectional imaging of materials structure using PS-OCT
PublikacjaOptical low-coherence tomography is a measurement technique for non-contact and non-destructive investigation of materials inner structure. Nowadays, this method is highly applied in medical treatment especially in dermatology and ophthalmology. During our research we have developed an optical low-coherence tomography system with polarization state analysis for structure examination of a broad range of technical materials. In this...
-
Crystal structure and physical properties of a novel ternary compound La15MoxGe9
PublikacjaWe present the synthesis, structural characterization and physical properties measurements of a new compound, La15MoxGe9 in Mn5Si3-type derived structure with interstitial Mo. The sample was synthesized by arc-melting method. La15MoxGe9 crystallizes in non-centrosymmetric hexagonal structure P63mc (#186) with lattice parameters a = b = 15.495(5) Å and c = 6.917(2) Å. The refinement on single X-ray diffraction data show that interstitial...
-
Study of microstress state of P91 steel using complementary mechanical Barkhausen, magnetoacoustic emission, and X-ray diffraction techniques
PublikacjaThe paper deals with assessment of microstress state of martensite P91 steel using three complementary techniques: mechanical Barkhausen emission, magnetoacoustic emission (MAE), and X-ray diffraction (XRD) profile analysis. Magnetic coercivity Hc and microstructure were investigated with inductive magnetometry and magnetic force microscopy (MFM), respectively. Internal stress level of P91 steel was modified by heat treatment....
-
Structure of Microemulsion Formulated with Monoacylglycerols in the Presence of Polyols and Ethanol
PublikacjaThe influence of polyols as cosurfactants (propylene glycol PG; glycerol G) and short chain alcohol as a cosolvent (ethanol EtOH) on the formation and solubilization capacity of the systems: hexadecane/monoacylglycerols (MAG)/polyol/water:EtOH, at 60C, was investigated. Electrical conductivity measurement, and the DSC method were applied to determine the structure and type of microemulsions formed. The dimension of the droplets...
-
ENERGY EFFICIENT SMALL INLAND PASSENGER SHUTTLE FERRY WITH HYBRID PROPULSION - CONCEPT DESIGN, CALCULATIONS AND MODEL TESTS
PublikacjaIn recent years, there has been a significant development in “green” and energy efficient propulsion systems, which fits into the general trend of environmentally friendly “green shipping”. The pursued goal is to construct a safe passenger ship that is low in energy demand and equipped with a highly energy efficient, emission-free propulsion system. The paper presents main problems encountered by designers of a small, hybrid-powered...
-
A structure and design of a novel compact UWB MIMO antenna
PublikacjaIn the paper, a concept and design procedure of a novel compact MIMO slot antenna is presented. In order to achieve a better filling of available space, individual antennas are constrained to a triangular shape and optimized for a reduced size. The MIMO structure is then assembled using the two of previously designed antennas in orthogonal arrangement. Surrogate-assisted numerical optimization involving variable-fidelity electromagnetic...
-
Effect of Different Structure Type Traffic On Railway Line Capacity
PublikacjaThe article points to methods of analyzing railway traffic conditions based on two parameters: capacity and delay of trains. The impact of the differentiated railway type structure on the capacity of the railway line was presented. Particular attention has been paid to the assessment of commonly used simplifications in analyzes.