Filtry
wszystkich: 1231
wybranych: 1039
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: INDUCTION MOTOR DRIVES, SLIDING‐MODE, SPEED OBSERVER, VARIABLE SPEED
-
Evolutionary Ship Track Planning within Traffic Separation Schemes – Evaluation of Individuals
PublikacjaThe paper presents an extended version of the author’s Evolutionary Sets of Safe Ship Trajectories method. The method plans safe tracks of all ships involved in an encounter including speed reduction manoeuvres, if necessary, and taking into account Rule 10 of COLREGS, which specifies ships’ behaviour within Traffic Separation Schemes governed by IMO. The paper focuses on the evaluation phase of the evolutionary process and shows...
-
Vibration of the bridge under moving singular loads - theoretical formulation and numerical solution
PublikacjaThe paper presents the results of the numerical analysis of a simple vehicle passing over a simply supported bridge span. The bridge is modelled by a Euler-Bernoulli beam. The vehicle is modelled as a linear, visco-elastic oscillator, moving at a constant speed. The system is described by a set of differential equations of motion and solved numerically using the Runge-Kutta algorithm. The results are compared with the solution...
-
Tool Wear Prediction in Single-Sided Lapping Process
PublikacjaSingle-sided lapping is one of the most effective planarization technologies. The process has relatively complex kinematics and it is determined by a number of inputs parameters. It has been noted that prediction of the tool wear during the process is critical for product quality control. To determine the profile wear of the lapping plate, a computer model which simulates abrasive grains trajectories was developed in MATLAB. Moreover,...
-
Effect of pulse laser treatment at different process variables on mechanical behavior of carbon nanotubes electrophoretically deposited on titanium alloy
PublikacjaPurpose: Titanium and its alloys are widely used as biomaterials for long-term implants, but they are usually surface-modified due to their weak bioactivity and wear resistance. Laser processing was used to modify the surface layer, and elemental carbon was a component of the deposited coatings. This research aims to use a combination of both methods based on preliminary electrophoretic deposition of multi-wall carbon nanotubes...
-
DIAGNOSTIC INFORMATION ANALYSIS OF QUICKLY CHANGING TEMPERATURE OF EXHAUST GAS FROM MARINE DIESEL ENGINE PART I SINGLE FACTOR ANALYSIS
PublikacjaIn this paper, attention was paid to the problem of low controllability of marine medium- and high-speed engines during operation, which significantly limits the parametric diagnosis. The measurement of quickly changing temperature of engine exhaust gas was proposed, the courses of which can be a source of diagnostic information. The F statistic of the Fisher-Snedecor distribution was chosen as a statistical tool. Laboratory tests...
-
Scale effect in the self-propulsion prediction for Ultra Large Container Ship with contra-rotating propellers
PublikacjaThis article addresses the problem of the scale effect for an Ultra Large Container Ship (ULCS) with a novel twin-crp-pod propulsion system. Twin-crp-pod steering-propulsion arrangement is an innovative solution that gains from three well-known systems: twin-propeller, contra-rotating propellers and pod propulsors. It is expected that applying the twin-crp-pod system to the analysed Ultra Large Container Ship will increase propulsion...
-
A Simple Neural Network for Collision Detection of Collaborative Robots
PublikacjaDue to the epidemic threat, more and more companies decide to automate their production lines. Given the lack of adequate security or space, in most cases, such companies cannot use classic production robots. The solution to this problem is the use of collaborative robots (cobots). However, the required equipment (force sensors) or alternative methods of detecting a threat to humans are usually quite expensive. The article presents...
-
Assessment of the Steering Precision of a Hydrographic Unmanned Surface Vessel (USV) along Sounding Profiles Using a Low-Cost Multi-Global Navigation Satellite System (GNSS) Receiver Supported Autopilot
Publikacjahe performance of bathymetric measurements by traditional methods (using manned vessels) in ultra-shallow waters, i.e., lakes, rivers, and sea beaches with a depth of less than 1 m, is often difficult or, in many cases, impossible due to problems related to safe vessel maneuvering. For this reason, the use of shallow draft hydrographic Unmanned Surface Vessels (USV) appears to provide a promising alternative method for performing...
-
Wpływ zmian dopuszczalnych wartości parametrów geometrycznych i kinematycznych na podatność modernizacyjną układów torowych
PublikacjaPodatnością modernizacyjną nazywamy stopień przystosowania analizowanego odcinka linii kolejowej do zmiany prędkości eksploatacyjnej. Skala możliwych zmian prędkości (w sensie jej zwiększenia) jest wypadkową istniejącego układu geometrycznego linii w planie, ograniczeń lokalizacyjnych oraz dopuszczalnych wartości parametrów geometrycznych i kinematycznych. Jakiekolwiek zmiany tych ostatnich wpływają bezpośrednio na obliczenie elementarnych...
-
Drgania i hałaśliwość silników asynchronicznych - weryfikacja nowych hipotez
PublikacjaArtykuł zawiera nowe spojrzenie na postaci drgań kadłuba i tarcz silników asynchronicznych wymuszanych siłami elektromagnetycznymi. Omówiono badania postaci drgań własnych i eksploatacyjnych kadłuba i tarcz łożyskowych. Poddano analizie związki przyczynowo-skutkowe postaci drgań tarcz łożyskowych z łożyskami tocznymi i ślizgowymi. Wykazano, że wibracyjne eksploatacyjne odkształcenia tarcz silników klatkowych małej i średniej mocy,...
-
Effect of underwater local cavity welding method conditions on diffusible hydrogen content in deposited metal
PublikacjaOne of the methods with great potential for applications in underwater repairs is local cavity welding. In local cavity method, cooling conditions and diffusible hydrogen amount in weld metal are nearly the same as those existed during welding in the air. This paper presents the results of literature survey and preliminary tests of the effect of local cavity welding conditions on diffusible hydrogen amount in a deposited metal....
-
The Imaging of Gdansk Bay Seabed by Using Side Sonar
PublikacjaThis paper is mainly aimed at presentation of an impact of environmental conditions on imaging accuracy by using hydro-acoustic systems in waters of a high non-uniformity of spatial distribution of hydrological parameters. Impact of refraction on erroneous estimation of range, in case of wave radiation into water under a large angle, like in side sonars or multi-beam echo-sounders, is especially important. In this paper seasonal...
-
Investigations on mixture preparation for two phase adiabatic pressure drop of R134a flowing in 5 mm diameter channel
PublikacjaThe article presents detailed two-phase adiabatic pressure drops data for refrigerant R134a. Study cases have been set for a mass flux varying from 200 to 400 kg/m2 s, at the saturation temperature of 19.4 ◦C. Obtained experimental data was compared with the available correlations from the literature for the frictional pressure drop during adiabatic flow. Influence of mixture preparation on pressure drop was investigated, for...
-
The study of acoustic climate of the Southern Baltic
PublikacjaThis paper presents the statistical characteristics of seawater properties, which are necessary for predicting the propagation of acoustic waves in selected areas of the Baltic Sea. The statistics were elaborated based on long-term measurements of vertical distributions of sound speed, temperature, and salinity, and the nonlinearity parameter B/A. Nonlinear properties of the environment are considered, in connection...
-
Simplified Map-based Selection of Optimal Spindle Speeds When Milling Complex Structures
PublikacjaIn the paper a method for selecting optimal spindle speeds for complex structures during milling operations is presented. It is based on the selection of the spindle speed in accordance with a simple equation resulting from the minimisation of vibration energy, which leads to the minimisation of the work of cut-ting forces presented in previous elaborations by the authors [1]. Optimal spindle speeds are obtained for many points...
-
Comparison of natural frequencies of a circular saw blade obtained empirically and with FEM
PublikacjaThe knowledge of the natural frequencies’ values of circular saw blades is necessary to determine the minimal critical rotational speed in which they can work with required stability. Moreover, testing the circular saw blades with more complicated shapes, e.g. which have additional holes inside blades for cleaning knifes or additional indirect teeth in gullets, reveals some kind of problematic properties of these saw blades. The...
-
Evaluation of Wear Resistance of Ti alloys used for elements friction of knee endoprosthesis
PublikacjaThe paper presents research results of resistance to abrasive wear of titanium alloys: Ti6Al4V (commonly used) and Til3Nb13Zr (alloy of new generation) in association with polyethylene (UHMW-PE) predisposed for elements on pair of the knee endoprosthesis. The results were analysed from the point of possibility of an use of new generation titanium alloys as components of such implants. The tests of resistance to abrasive wear of...
-
Simple gait parameterization and 3D animation for anonymous visual monitoring based on augmented reality
PublikacjaThe article presents a method for video anonymization and replacing real human silhouettes with virtual 3D figures rendered on a screen. Video stream is processed to detect and to track objects, whereas anonymization stage employs animating avatars accordingly to behavior of detected persons. Location, movement speed, direction, and person height are taken into account during animation and rendering phases. This approach requires...
-
Disturbances of magnetic field in surrounding of mobile, metalic plate
PublikacjaThe uniform magnetic field of the Earth in the surrounding of a mobile, metalic object undergoes deformation by eddy currents. The influence of the moving conducting object on total magnetic field of the Earth depends on the object's shape, position and speed of the changes relative to the magnetic field's vector of the Earth as well as the electric conductivity and the relative magnetic permeability of the material. The disturbances...
-
Apparent molar volumes and compressibilities of alkaline earth metal ions in methanol and dimethylsulfoxide
PublikacjaTemperature dependencies of density of magnesium (II), calcium (II), strontium (II), barium (II) perchlorates as well as beryllium (II), and sodium trifluoromethanesulfonates in methanol and dimethylsulfoxide have been determined over the composition range studied. From density data the apparent molar volumes and partial molar volumes of the salts at infinite dilution as well as the expansibilities have been evaluated. The apparent...
-
Modelling of the Movement of Designed Vehicles on Parking Space for Designing Parking
PublikacjaNowadays, in all cities there is an acute problem of lack of parking spaces. The vehicles are becoming more and more not only in megacities, but also in small cities of the country, and there are no more parking places - the pace of solving the problem is several times slower than the speed of transport growth among the citizens. The article is dedicated to determination of the optimum sizes parking place for designing vehicles...
-
Fluctuation-Enhanced Sensing (FES): A Promising Sensing Technique
PublikacjaFluctuation-enhanced sensing (FES) is a very powerful odor and gas sensing technique and as such it can play a fundamental role in the control of environments and, therefore, in the protection of health. For this reason, we conduct a comprehensive survey on the state-of-the-art of the FES technique, highlighting potentials and limits. Particular attention is paid to the dedicated instrumentation necessary for the application of...
-
Novel Investigation of Higher Order Spectral Technologies for Fault Diagnosis of Motor-Based Rotating Machinery
PublikacjaIn the last decade, research centered around the fault diagnosis of rotating machinery using non-contact techniques has been significantly on the rise. For the first time worldwide, innovative techniques for the diagnosis of rotating machinery, based on electrical motors, including generic, nonlinear, higher-order cross-correlations of spectral moduli of the third and fourth order (CCSM3 and CCSM4, respectively), have been comprehensively...
-
Investigation of Weigh-in-Motion Measurement Accuracy on the Basis of Steering Axle Load Spectra
PublikacjaWeigh-in-motion systems are installed in pavements or on bridges to identify and reduce the number of overloaded vehicles and minimise their adverse eect on road infrastructure. Moreover, the collected trac data are used to obtain axle load characteristics, which are very useful in road infrastructure design. Practical application of data from weigh-in-motion has become more common recently, which calls for adequate attention to...
-
Analysis of Residual Stresses and Dislocation Density of AA6082 Butt Welds Produced by Friction Sir Welding
PublikacjaThe Friction Stir Welding (FSW) method was employed to join AA6082 sheets. The welds were produced with different tool traverse speed (200 and 250 mm/min), rotational speed (1000 and 1250 RPM) and tool tilt angle (0 and 2 deg). Based on the analysis of XRD patterns, the total precipitation volume fractions in the nugget zones and the base material were calculated. The FSW process resulted in a reduction in the fraction of precipitates...
-
Energy Management for PV Powered Hybrid Storage System in Electric Vehicles Using Artificial Neural Network and Aquila Optimizer Algorithm
PublikacjaIn an electric vehicle (EV), using more than one energy source often provides a safe ride without concerns about range. EVs are powered by photovoltaic (PV), battery, and ultracapacitor (UC) systems. The overall results of this arrangement are an increase in travel distance; a reduction in battery size; improved reaction, especially under overload; and an extension of battery life. Improved results allow the energy to be used efficiently,...
-
Contribution of dynamic vehicle loads to pavement failure
PublikacjaPavement surfaces are not ideally even, which causes dynamic loads of vehicle axles. Distribution of dynamic loads of a given axle is similar to normal distribution and can be described by static load and dynamic load coefficient. The dynamic load coefficient depends on road profile, vehicle speed, properties of suspensions and static load of axle. While for a given road section road profile remains constant, vehicle speed and...
-
Effect of Processing Parameters on Strength and Corrosion Resistance of Friction Stir-Welded AA6082
PublikacjaThe friction stir welding method is increasingly attracting interest in the railway sector due to its environmental friendliness, low cost, and ease of producing high-quality joints. Using aluminum alloys reduces the weight of structures, increasing their payload and reducing fuel consumption and running costs. The following paper presents studies on the microstructure, strength, and corrosion resistance of AA6082 aluminum alloy...
-
Effectiveness of Random Field Approach in Serviceability Limit State Analysis of Strip Foundation
PublikacjaThis work conducts a probabilistic inquiry on how the variability of the parameter defining soil deformability affects the settlement of the foundation located on the soil. The analysis addresses the random foundation model to relevantly estimate the probability of allowable deflection exceedance. The constitutive model parameter is based either on a single random variable or a random field. The computations incorporate direct...
-
A multithreaded CUDA and OpenMP based power‐aware programming framework for multi‐node GPU systems
PublikacjaIn the paper, we have proposed a framework that allows programming a parallel application for a multi-node system, with one or more GPUs per node, using an OpenMP+extended CUDA API. OpenMP is used for launching threads responsible for management of particular GPUs and extended CUDA calls allow to manage CUDA objects, data and launch kernels. The framework hides inter-node MPI communication from the programmer who can benefit from...
-
Emotion Recognition - the need for a complete analysis of the phenomenon of expression formation
PublikacjaThis article shows how complex emotions are. This has been proven by the analysis of the changes that occur on the face. The authors present the problem of image analysis for the purpose of identifying emotions. In addition, they point out the importance of recording the phenomenon of the development of emotions on the human face with the use of high-speed cameras, which allows the detection of micro expression. The work that was...
-
TIRE/ROAD NOISE AND TIRE ROLLING RESISTANCE ON PROTOTYPE PERS SURFACE
PublikacjaPoroelastic road surfaces are characterized by low noise of tires running on them.Road pavements of this type are promising solution to problems related to traffic noise in cities and on rural roads. Some technical problems still have to be solved, in particular regarding durability and skid resistance on wet surface. Ongoing and planned works are to contribute to create a quiet, durable and safe road surface, which will become...
-
Characteristics of an image sensor with early-vision processing fabricated in standard 0.35 µm CMOS technology
PublikacjaThe article presents measurement results of prototype integrated circuits for acquisition and processing of images in real time. In order to verify a new concept of circuit solutions of analogue image processors, experimental integrated circuits were fabricated. The integrated circuits, designed in a standard 0.35 µm CMOS technology, contain the image sensor and analogue processors that perform low-level convolution-based image...
-
Application in circular sawing machines of the experimental results of investigations of the chip removing system operation
PublikacjaThe experimental results of the chip removing system operation are presented. The main aim of them was to optimize suction system of the panel saw Fx3 and its follower Fx550. The attention was focused on the upper casing, which was the part of removing system. Within the framework of the work a systematic experimental study of pressure distribution in the casing during operation of the selected rotational speed of saw blade with...
-
Numerical investigation on the performance of a small counter-rotating wind turbine
PublikacjaThe article presents the results of the investigation on the performance of a small counter-rotating wind turbine. The wind turbine has been simulated using Computational Fluid Dynamics methods. Actuator Line Model has been successfully used to represent rotors in the computational domain. A parametric study has been carried out, taking into account changes in the tip speed ratio of the rotors while maintaining a constant distance...
-
A bound on the number of middle-stage crossbars in f-cast rearrangeable Clos networks
PublikacjaIn 2006 Chen and Hwang gave a necessary and sufficient condition under which a three-stage Clos network is rearrangeable for broadcast connections. Assuming that only crossbars of the first stage have no fan-out property, we give similar conditions for f-cast Clos networks, where f is an arbitrary but fixed invariant of the network. Such assumptions are valid for some practical switching systems, e.g. high-speed crossconnects....
-
Approximate models and parameter analysis of the flow process in transmission pipelines
Publikacjathe paper deals with the problem of early leak detection in transmission pipelines. First we present the derivation of state-space equations of the flow process in the pipelines. This description is then aggregated in order to obtain a principal model. Next, the problem of process model parameterization is addressed, taking into account the maximization of a model stability margin. The location of the maximum is determined using...
-
A multistage turbine for a micro power plant
PublikacjaThis paper presents results of a design analysis of a multi-stage turbine for the cogeneration micro-power plant working in accordance with Organic Rankine Cycle (ORC). The heat power of the plant is assumed equal to 20 kW and the corresponding available electric output is estimated to be of about 3 kW. Different variants of the radial and axial-flow turbines have been considered, while the detailed results of the calculations...
-
Analog CMOS processor for early vision processing with highly reduced power consumption
PublikacjaA new approach to an analog ultra-low power visionchip design is presented. The prototype chip performs low-levelconvolutional image processing algorithms in real time. Thecircuit is implemented in 0.35 μm CMOS technology, contains64 x 64 SIMD matrix with embedded analogue processors APE(Analogue Processing Element). The photo-sensitive-matrix is of2.2 μm x 2.2 μm size, giving the density of 877 processors permm2. The matrix dissipates...
-
Comparison of Tracking Methods in Respect of Automation of Animal Behavioral Test
PublikacjaAutomation in experiments carried out on animals is getting more and more important in research. Computers take over laborious and time-consuming activities like recording and analysing images of experiment scene. The first step in an image analysis is finding and distinguishing between the observed animals, and then tracking all objects during the experiment. In this paper four tracking methods are presented. Quantitative and...
-
One Europe, one product, two prices - the price disparity in the EU
PublikacjaThe price dispersion in the European Union in the last fifteen years (1990-2005) is analysed. The analysis of price convergence is examined on aggregate and disaggregate levels. The macro approach is based on Comparative Price Level index calculated as the ratio between PPPs and exchange rate. The disaggregate analysis utilizesactual prices of 148 individual products sold in the 15 capital cities of the EU. The calculations comprise...
-
CMOS implementation of an analogue median filter for image processing in real time
PublikacjaAn analogue median filter, realised in a 0.35 μm CMOS technology, is presented in this paper. The key advantages of the filter are: high speed of image processing (50 frames per second), low-power operation (below 1.25 mW under 3.3 V supply) and relatively high accuracy of signal processing. The presented filter is a part of an integrated circuit for image processing (a vision chip), containing: a photo-sensor matrix, a set of...
-
Real-time generator of AIS/ARPA/GPS data
PublikacjaThe paper presents a real-time generator of AIS/ARPA/GPS position data in the standardized NMEA 0183 text format. Position data are produced by a set of various types of ships simulated on the Polish part of the Baltic Sea and are generated on defined IP/UDP addresses and RS-232 ports. In the simulation an extensive set of input parameters is taken into account including the number of particular types of ships, their dimensions,...
-
Enhanced Eye-Tracking Data: a Dual Sensor System for Smart Glasses Applications
PublikacjaA technique for the acquisition of an increased number of pupil positions, using a combined sensor consisting of a low-rate camera and a high-rate optical sensor, is presented in this paper. The additional data are provided by the optical movement-detection sensor mounted in close proximity to the eyeball. This proposed solution enables a significant increase in the number of registered fixation points and saccades and can be used...
-
DIGITAL HYDRAULICS CIRCUIT BASED ON PWM FUNCTION FOR CONTROLLING HYDRAULIC ACTUATOR POSITION
PublikacjaHydraulic systems are used in many different industries, such as multi-source hydrostatic drive systems. In traditional hydraulic systems, a proportional servo valve is used to control the position of hydraulic actuators. The low energy efficiency and high cost of these control valves are two major problems with these systems. Digital hydraulics is one of the most unique ideas on how to solve these problems. Researchers like digital...
-
A new concept of PWM duty cycle computation using the Barycentric Coordinates in a Three-Dimensional voltage vectors arrangement
PublikacjaThe paper presents a novel approach to the Pulse Width Modulation (PWM) duty cycle computing for complex or irregular voltage vector arrangements in the two (2D) and three–dimensional (3D) Cartesian coordinate systems. The given vectors arrangement can be built using at least three vectors or collections with variable number of involved vectors (i.e. virtual vectors). Graphically, these vectors form a convex figure, in particular,...
-
Electrochemical synthesis of 2D copper coordination-polymers: Layer-stacking deviation induced by the solvent and its effect on the adsorptive properties
PublikacjaA 2D Cu-based Metal-Organic Framework (MOF), namely copper-terephthalate (Cu(1,4-BDC)), was successfully synthesized by electrochemical method for effective methylene blue (MB) sorption from aqueous solutions. The composition, morphology, and the presence of functional groups in the obtained material were verified by Fourier Transform Infrared spectroscopy (FTIR), Powder X-Ray Diffraction (PXRD), Thermal (TGA), and Elemental (EA)...
-
Extended duration running and impulse loading characteristics of an acoustic bearing with enhanced geometry
PublikacjaThis paper presents performance during prolonged running of the acoustic bearing when PZTs are switched off and when they are switched on. The effect of active PZT on shaft’s displacements in X and Y directions is clearly demonstrated. Performance of the acoustic bearing was also assessed when an impulse force was applied to the running shaft at speed. Once again the benefits of having PZTs active are beyond doubt. The instability...
-
Simulation of large thrust-bearing performance at transient states, warm and cold start-up
PublikacjaThe start-up of a large hydrodynamic thrust bearing of a vertical hydrogenerator is one of the most critical situations during the lifetime of a bearing. Hydrodynamic load capacity is low due to low speed and higher thermal deformations of the pad. A new approach to the simulation of a hydrodynamic bearing is shown in this article. A combination of finite elements method and computational fluid dynamics is used to perform the transient...
-
A correlation between electron-hole pair radii and magnetomodulation of exciplex fluorescence in electron donor-electron acceptor organic systems
PublikacjaElectric field dependencies of electromodulated photoluminescence and magnitudes of the magnetic-field effect on photoluminescence havebeen measured in vacuum-evaporated films of m-MTDATA [4,4',4"-tris(N-(3-methylphenyl)-N-phenylamino)triphenylamine]:bathophe-nanthroline, m-MTDATA:BCP (bathocuproine), as well as 4,4',4"-tris[2-naphthyl(phenyl)amino]triphenylamine:BCP. The Sano-Tachiya-Noolandi-Hong extension of standard Onsager...