Wyszukiwarka
Filtry
wszystkich: 1700
wybranych: 1276
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: cavitation erosion resistance
-
Fluctuation enhanced gas sensing using UV irradiated Au-nanoparticle-decorated WO3-nanowire films
PublikacjaWO3 nanowires (WO3-NWs) decorated with gold nanoparticles (AuNPs) were utilized in resistive gas sensor devices to detect ethanol by use of fluctuation enhanced sensing (FES). The experimental system records both DC resistance and fluctuations of the sensing film. Our data verify that the sensitivity and selectivity of the gas sensor are improved by applying FES when the sensor is stimulated with a combination of UV light and heating....
-
Nickel Oxide Thin Film Sensor for Fluctuation-Enhanced Gas Sensing of Formaldehyde
PublikacjaNanocrystalline nickel-oxide-based thin films were prepared by advanced reactive gas deposition, and the response of these films to formaldehyde was studied by fluctuationenhanced sensing. Morphological and structural analyses showed porous deposits of nickel oxide particles with face-centered cubic structure. Resistance fluctuations were measured upon exposure to ethanol, formaldehyde and methane at 200 °C. Power density spectra...
-
Measurement methods for assessing insulation condition of underground pipelines
PublikacjaThe paper discusses the most frequently applied measurement methods for assessing the quality of external insulation along pipelines and detecting defect locations in the protective coating. The quality of coating along a given pipeline section under investigation is assessed by determining unitary resistance of the coating, which is calculated on the basis of measurement results obtained along a pipeline subjected to cathodic...
-
Investigation of polyurethane elastomer–steel joints using glass lacquer as an adhesive agent
PublikacjaThis article describes an innovative method of coupling polyurethane elastomer (based on polyurethane glycolysate) with constructional steel, by implementation of a Glaspur®—glass lacquer containing latent polyurethanes and monosilane adhesion promoters. The commonly applied coupling agent is Cilbond® 45SF glue or its derivatives. Additionally, glycolysate was synthesised from polyurethane waste and 1,3-propylene glycol in 6:1...
-
Improved performance of LaNi0.6Fe0.4O3 solid oxide fuel cell cathode by application of a thin interface cathode functional layer
PublikacjaIn this work, novel functional layers were prepared by a low temperature spray pyrolysis method on the oxygen side of the solid oxide cells. Thin layers of Ce0.8Gd0.2O2 and LaNi0.6Fe0.4O3 are prepared between the electrolyte and the porous oxygen electrode. Additionally the influence of the sprayed ceria barrier layer on the zirconia based electrolyte with the new layers is evaluated. Impedance spectroscopy results show improvement...
-
Experimental investigations on pressure drop during the condensation in flow of HFE7000 in vertical minichannel
PublikacjaIn the work presented in the paper authors focused attention on the issues of flow resistance and pressure drop during condensation in the flow. The case of the descending flow through a cylindrical single-channel of 2.3 mm inner diameter was carefully analyzed. In the course of investigations a new working fluid HFE 7000 has been scrutinised which has a strongly differing properties in comparison to the other fluids that are commonly...
-
Effect of native air-formed oxidation on the corrosion behavior of AA7075 aluminum alloys
PublikacjaThe microstructure of aluminum alloys plays a key role in their corrosion resistance. In particular, the presence of intermetallic precipitates differing in the potential from the alloy matrix induces local corrosion. The study presents the effect of native air-formed oxidation on the corrosion behavior of AA 7075 aluminum alloy. Various microscopic and spectroscopic techniques were used to examine the changes occurring in the...
-
Scientific research in the Department of Machine Design and Automotive Engineering
PublikacjaShort descriptions of various research subjects taken up at the Department of Machine Design and Automotive Engineering are included in the paper. The subjects cover a wide range of bearing systems and tribology research and the research on tires and road surfaces. A third field of activity is biomedical engineering – with the attempts to improve methods of modelling biological materials in FEM calculations. The Department has...
-
Uncertainty estimation of loop impedance measurement determined by the vector method
PublikacjaThis article presents a detailed analysis of uncertainty estimation of loop impedance measurement determined by the vector method. The analysis includes the following estimates: resistance variance, voltage variance and time measurement variance. This paper presents a methodology for estimating the combined standard uncertainty of loop impedance by the vector method. The vector method allows to determine loop impedance based on...
-
Dynamics of Ice Jam Formation and Release
PublikacjaThe numerical model DynaRICE and its application to ice jam formation and release is presented. The model is a two-dimensional coupled flow and ice dynamic model. The ice dynamic component, which includes both the internal ice resistance and boundary friction on ice motion, uses a Lagrangian SPH method. The hydrodynamic component of the model uses a streamline upwind finite element method, which is capable of simulating trans-critical...
-
Investigations of Titanium Implants Covered with Hydroxyapatite Layer
PublikacjaTo reduce unfavorable phenomena occurring after introducing an implant into human body various modifications of the surface are suggested. Such modifications may have significant impact on biocompatibility of metallic materials. The titanium and it's alloys are commonly used for joint and dental implants due to their high endurance, low plasticity modulus, good corrosion resistance as well as biocompatibility. Special attention...
-
Analysis of sloping brace stiffness influence on stability and load bearing capacity of a truss
PublikacjaThe paper is focused on the numerical study of stability and load bearing capacity of a truss with side elastic braces. The structure is made in reality. The rotational and sliding brace stiffnesses were taken into account. Linear buckling analysis and non-linear static analysis with geometric and material nonlinearity were performed for the beam and shell model of the truss with respect to the angle of sloping braces. As a result...
-
Accurate electrothermal modelling of high frequency DC-DC converters with discrete IGBTs in PLECS software
PublikacjaIn the paper, a novel, improved method of the IGBT junction temperature computations in the PLECS simulation software is presented. The developed method aims at accuracy of the junction temperature computations in PLECS by utilising a more sophisticated model of transistor losses, and by taking into account variability of transistor thermal resistance as a function of its temperature. A detailed description of the proposed method,...
-
Stability of an imperfect truss loaded by wind
PublikacjaThe present paper is devoted to the numerical research of stability of a truss loaded by wind and stiffened by elastic supports located at the top chord. The lateral braces or lateral and torsional braces were taken into account. In this paper, the linear buckling analysis re- sults for the beam and shell model were presented. Two different shapes of initial geometric imperfections were considered in the non-linear static analysis...
-
Effect of polymer fibres reinforcement on selected properties of asphalt mixtures
PublikacjaThe paper presents selected results of the research program concerning fibre reinforced asphalt concrete. Aramid-polyalphaolefin fibres was used in this study. Selected properties responsible for low temperature cracking and resistance to permanent deformation are presented in this paper. Low temperature cracking susceptibility was evaluated with the results obtained from bending test of rectangular beams with constant rate of...
-
СИСТЕМА КОНТРОЛЯ СОСТОЯНИЯ ИЗОЛЯЦИИ ЭЛЕКТРОПРИВОДОВ В СЕТЯХ С ГЛУХОЗАЗЕМЛЕННОЙ НЕЙТРАЛЬЮ (System of insulation status monitoring for electric drives in networks with a dead-earth neutral)
PublikacjaПредложен метод контроля изоляции частотно-регулируемых электроприводов в сетях с глухозаземленной нейтралью. Система контроля изоляции включается в момент остановки электропривода. Ключи инвертора коммутируются по специальному закону, и с помощью сигнала трансформатора тока, который изме- ряет ток во всех трех фазах привода одновременно, определяется ток утечки. Рассмотрена схема датчика тока утечки и приведены экспериментальные...
-
Zastosowanie audytu wewnętrznego u operatorów produkcyjnych w zapobieganiu kryzysom-studium przypadku
PublikacjaGłównym tematem artykułu była analiza badań przeprowadzonych u producenta farb proszkowych przedsiębiorstwa X, w zakresie zastosowania audytu wewnętrznego, jako metody pozwalającej na zapobieganie pojawienia się kryzysu. Właściwa współpraca operatorów produkcyjnych z menedżerami ma kluczowe zna-czenie dla budowy właściwej pozycji audytu wewnętrznego w przedsiębiorstwie X. Brak należytej współpracy na etapie badań, przy braku...
-
Glucose metabolism disorders in patients with non-functioning adrenal adenomas — single-centre experience
PublikacjaIntroduction: The presence of glucose metabolism disorders and their possible correlation with degree of cortisol secretion were evaluated in patients with non-functioning adrenal incidentalomas (NFAIs). Material and methods: The study group consisted of 131 patients with hormonally inactive adrenal incidentalomas....
-
Influence of grain shape on the mechanical behaviour of granular materials
PublikacjaWe performed series of numerical vertical compression tests on assemblies of 2D granular material using a Discrete Element code and studied the results in regard to the grain shape. The samples consist of 5000 grains made either of 3 overlapping discs (clump - grain with concavities) or of six-edged polygons (convex grain). These two types of grains have a similar external envelope, ruled with a geometrical parameter α. In the...
-
Development and experimental validation of a novel double-stage yield steel slit damper-buckling restrained brace
PublikacjaThis research is focused on the development and experimental validation of a novel double-stage yield steel slit damper-buckling restrained brace (SSD-DYB) system designed for seismic resistance of steel structures. The SSD-DYB integrates the energy dissipation capability of a steel slit damper (SSD) in its initial segment, enhancing performance in the case of lower seismic intensities levels while employing a larger segment for...
-
Influence of CeO2 and TiO2 Particles on Physicochemical Properties of Composite Nickel Coatings Electrodeposited at Ambient Temperature
PublikacjaThe Ni-TiO2 and Ni-CeO2 composite coatings with varying hydrophilic/hydrophobic characteristics were fabricated by the electrodeposition method from a tartrate electrolyte at ambient temperature. To meet the requirements of tight regulation by the European Chemicals Agency classifying H3BO3 as a substance of very high concern, Rochelle salt was utilized as a buffer solution instead. The novelty of this study was to implement a...
-
Modal Analysis of a Steel Radial Gate Exposed to Different Water Levels
PublikacjaWith the increase in water retention needs and planned river regulation, it might be important to investigate the dynamic resistance of vulnerable elements of hydroelectric power plants, including steel water locks. The most frequent dynamic loads affecting hydroengineering structures in Poland include vibrations caused by heavy road and railway traffic, piling works and mining tremors. More destructive dynamic loads, including...
-
Effect of the let-through energy of overcurrent protective devices on the temperature of conductors during short-circuits
PublikacjaThe scope of the verification of low-voltage systems covers the earth fault loop impedance measurement. This measurement is usually performed with the use of low-value current meters, which force a current many times lower than the one occurring during a real short-circuit. Therefore, the international standard recommends consideration of the increase of resistance of conductors with the increase of temperature, which may occur...
-
Biocompatibility and Bioactivity of Load-Bearing Metallic Implants
PublikacjaThe main objective of here presented research is to develop the titanium (Ti) alloy base composite materials possessing better biocompatibility, longer lifetime and bioactivity behaviour for load-bearing implants, e.g. hip joint and knee joint endoprosthesis. The development of such materials is performed through: modeling the material behaviour in biological environment in long time and developing of new procedures for such evaluation;...
-
Improvement of Fingerprinting Method based on Hill Cipher by using Frequency Domain
PublikacjaThe main goal of this paper is to present the advantages of a digital fingerprinting in a frequency domain over a pixel domain, in case of VoD services (Video on Demand). The paper presents basic issues of a multimedia data protection by digital fingerprinting. It also describes threats to embedded fingerprints from both collusion attacks and from a transmission itself. Possible solution was presented on the example of the DCT...
-
Secured wired BPL voice transmission system
PublikacjaDesigning a secured voice transmission system is not a trivial task. Wired media, thanks to their reliability and resistance to mechanical damage, seem an ideal solution. The BPL (Broadband over Power Line) cable is resistant to electricity stoppage and partial damage of phase conductors, ensuring continuity of transmission in case of an emergency. It seems an appropriate tool for delivering critical data, mostly clear and understandable...
-
Stability and limit load analysis of a cold-formed channel section column
PublikacjaThe paper presents stability and limit load analysis of a steel column 1440 mm high of a cold-formed channel section, subjected to a combination of compression and bending. Experimental results were compared to the resistance of a code procedure and to the outcome of numerical non-linear analysis. Comparison was made of numerical solutions by means of static (Riks) and dynamic (Explicit and Implicit) methods. Perfectly elastic...
-
Properties comparison of rubber and three layer PTFE-NBR-bronze water lubricated bearings with lubricating grooves along full bush circumference based on experimental tests
PublikacjaWater lubricated bearings have been in industrial use for well over a century. During the last decade their traditional range has been expanded with new, modern products. Despite that fact, certain solutions continue to employ the standard rubber bearing with lubricating grooves located along entire bush circumference. The work presents experimental research conducted on comparable sliding bearings with lubrication grooves along...
-
UWB-Based Indoor Navigation in a Flexible Manufacturing System Using a Custom Quadrotor UAV
PublikacjaA novel solution for indoor navigation of a transportation drone in flexible manufacturing is presented in this paper. To address the challenges of accurate and robust drone navigation in occluded environments, an ultra-wideband (UWB) navigation system has been integrated with a commercially available open source control platform. The system offers high accuracy (± 20 mm), low power consumption, resistance to electronic interference,...
-
NANOCRYSTALLINE CATHODES FOR SOLID OXIDE FUEL CELLS MADE OF NOBLE METALS
PublikacjaCathodes for solid oxide fuel cells prepared by the infiltration method at 600 °C are presented. The infiltration method allows to produce stable, nanostructured electrodes. Cathodes were prepared using gold, platinum, La2NiO4+δ (L2N) and La0.6Sr0.4Co0.2Fe0.8O3 δ (LSCF). Symmetrical cathode/electrolyte/cathode samples were prepared and examined with SEM microscopy and electrochemical impedance spectroscopy. Despite successful deposition...
-
Fluctuation enhanced gas sensing with WO3-based nanoparticle gas sensors modulated by UV light at selected wavelengths
PublikacjaThe sensitivity and selectivity of WO3-based gas sensors can be enhanced by UV-irradiation-induced modulation, especially if different wavelengths are employed. We used fluctuation-enhanced gas sensing, based on measurements of resistance fluctuations in the gas sensor, to study the effects of such modulation on the noise intensity for ambient atmospheres of synthetic air without and with additions of small amounts of ethanol,...
-
Ocena stanu technicznego konstrukcji zgarniaczy będących na wyposażeniu osadników wstępnych Grupowej Oczyszczalni Ścieków „DĘBOGÓRZE
PublikacjaOsadniki wstępne typu DORRA – 4 szt., o pojemności 1830 m3, wyposażone są w elementy mechaniczne do kierunkowego przemieszczania się osadu w kierunku leja centralnego. Celem pracy jest ocena stany technicznego części mechanicznej, a w szczególności: - konstrukcji zespołu zgarniania części pływających oraz osadu. - zespołu napędu i sterowania, - zespołu napędu i jazdy. Pierwsze dwa zespoły będą oceniane również z punktu widzenia...
-
Wpływ błędów parametrów modelu maszyny indukcyjnej na działanie rozszerzonego obserwatora prędkości
PublikacjaW artykule opisano metodę odtwarzania prędkości wirnika maszyny indukcyjnej przy wykorzystaniu rozszerzonego obserwatora prędkości. Zbadano wpływ błędów parametrów modelu maszyny indukcyjnej na właściwości dynamiczne obserwatora poprzez porównanie macierzy stanu obserwatora obarczonego oraz nieobarczonego błędami parametrów. Zbadany został także wpływ błędów parametrów na jakość odtwarzania zmiennych maszyny w stanie ustalonym.
-
A comparative performance assessment of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublikacjaThis work presents the investigation results of a journal bearing lubricated with magnetorheological fluid that is activated by a local constant magnetic field to vary both the local flow resistance and pressure. The bearing performance is assessed via Finite Element Modelling (FEM) and results are corroborated by experiments. The FEM model uses the Bingham model to describe the fluid film. A dedicated test rig is used to assess...
-
Stability of a truss under upward wind loading
PublikacjaThe present paper is devoted to the numerical investigations of stability of a truss under upward wind load. The truss is braced at its the upper cord. A structural variant including lateral braces, or lateral and torsional braces is considered. The research presents the problems of linear buckling and non-linear static analysis of the truss shell and beam model with geometric and material non-linearity are presented. The initial...
-
Transformation of bimetallic Ag–Cu thin films into plasmonically active composite nanostructures
PublikacjaFormation of plasmonically active silver, copper and composite silver-copper nanostructures were studied in this paper. Metallic nanostructures were fabricated by thermal disintegration, so called dewetting, of the thin films in an argon atmosphere. The formation process of the nanostructures was in-situ observed by a novel method, based on resistance measurements. The influence of the material and thickness of the initial thin...
-
Degradation of reference tyres used for CPX measurements
PublikacjaMeasurements of tyre/road noise using the Close Proximity Method are based on reference tyres that are described in ISO/TS 11819-3. The standard specifies two tyres, namely "P1" and "H1" that should be used during measurements. To be used for measurements each tyre must fulfill certain conditions that are listed in the standard. The conditions are related to the tread pattern depth and rubber hardness. During experiments performed...
-
Production of fuel briquette from solid waste biomass using natural resin as a binder
PublikacjaBackground: This research aimed to evaluate the use of natural resin as a binder for the production of fuel briquette from solid waste biomass.Methods: Proximate analyses were made for fuel briquette prepared from solid waste biomass using natural resin as a binder in comparison with using starch as a binder.Results: The results for density, percent content of moisture, percent content of volatile matter, percent...
-
Production of fuel briquette from solid waste biomass using natural resin as a binder
PublikacjaAbstract Background: This research aimed to evaluate the use of natural resin as a binder for the production of fuel briquette from solid waste biomass. Methods: Proximate analyses were made for fuel briquette prepared from solid waste biomass using natural resin as a binder in comparison with using starch as a binder. Results: The results for density, percent content of moisture, percent content of volatile matter, percent content...
-
Influence of selected WMA additives on viscoelastic behaviour of asphalt mixes and pavements
PublikacjaWarm mix asphalt additives are effective in decreasing production, laying and compaction temperatures of asphalt mixes. However, there are still questions concerning influence of warm mix additives on properties of asphalt mixes and pavement performance. This paper presents results of the comprehensive research of viscoelastic behaviour of asphalt mixes and pavement structures with layers made with warm mix asphalt additives at...
-
Osteoblast and bacterial cell response on RGD peptide‐functionalized chitosan coatings electrophoretically deposited from different suspensions on Ti13Nb13Zr alloy
PublikacjaMetallic materials for long-term load-bearing implants still do not provide high antimicrobial activity while maintaining strong compatibility with bone cells. This study aimed to modify the surface of Ti13Nb13Zr alloy by electrophoretic deposition of a chitosan coating with a covalently attached Arg-Gly-Asp (RGD) peptide. The suspensions for coating deposition were prepared in two different ways either using hydroxyacetic acid...
-
Effects of preheating on laser beam–welded NSSC 2120 lean duplex steel
PublikacjaDuplex stainless steels show sustainable alternative for the conventional austenitic grades, with higher strength, higher resistance against stress corrosion cracking, and lower purchase cost. Thus, duplex stainless steel gains more attention in construction, oil and gas, and chemical industries. Among duplex stainless steels, low nickel and low molybdenum alloyed lean duplex stainless steel are a cost-efective substitution of...
-
Experimental Investigation of the Thermal Performance of a Wickless Heat Pipe Operating with Different Fluids: Water, Ethanol, and SES36. Analysis of Influences of Instability Processes at Working Operation Parameters
PublikacjaIn this study, the influences of different parameters on performance of a wickless heat pipe have been presented. Experiments have been carried out for an input power range from 50 W to 300 W, constant cooling water mass flow rate of 0.01 kg/s, and constant temperature at the inlet to condenser of 10 C. Three working fluids have been tested: water, ethanol, and SES36 (1,1,1,3,3-Pentafluorobutane) with different filling ratios (0.32,...
-
Activity of isavuconazole and other triazole derivatives against clinical isolates of Aspergillus fumigatus
PublikacjaAspergillus fumigatus is the most frequent pathogen of the genus Asperillus, which is highly susceptible to triazole derivatives, especially to isavuconazole and voriconazole. Many countries face a growing problem of infections due to A. fumigatus showing acquired resistance to one or several triazoles. In medical centres, monitoring the susceptibility of isolated Aspergillus spp. is recommended. The aim of this study was to collect...
-
Timber - material of the future. Examples of small wooden architecture structures.
PublikacjaThe aim of this article is to present various types of wood-based products, classified as engineered timber, while specifying the implications of their structural properties for their forms. Timber is used as a construction material due to its fire resistance, good structural characteristics and insulating properties. The advent of new technologies of wood processing and wood-based materials production has converted timber into...
-
Concrete mix design using machine learning
PublikacjaDesigning a concrete mix is a process of synthesizing many components, it is not a simple process and requires extensive technical knowledge. The design process itself focuses on obtaining the required strength of concrete. Very often designing a concrete mix takes into account the need to maintain the proper water-demand and frost-resistance features. The parameters that influence the concrete class most significantly are the...
-
Proceedings of the fib Symposium 2019: Concrete - Innovations in Materials, Design and Structures 2019
PublikacjaDesigning a concrete mix is a process of synthesizing many components, it is not a simple process and requires extensive technical knowledge. The design process itself focuses on obtaining the required strength of concrete. Very often designing a concrete mix takes into account the need to maintain the proper water-demand and frost-resistance features. The parameters that influence the concrete class most significantly are the...
-
Wpływ zbrojenia polimerowymi włóknami rozproszonymi na wybrane właściwości mieszanek mineralno-asfaltowych
PublikacjaW artykule przedstawiono wybrane wyniki badań mieszanek mineralno-asfaltowych zbrojonych polimerowymi włóknami rozproszonymi. Ocenie poddano mieszankę włókien zbrojących aramidowo-poliolifenowych pod kątem wpływu ich zastosowania na właściwości niskotemperaturowe i odporności na deformacje trwałe mieszanek mineralno-asfaltowych. Właściwości niskotemperaturowe oceniano na podstawie testu zginania próbek belkowych oraz na podstawie...
-
Prognozowanie krzywej osiadania pala wierconego z iniekcją ciśnieniową pod podstawą
PublikacjaArtykuł jest kontynuacją tematyki autora dotyczącą mechanizmu działania iniekcji ciśnieniowej pod podstawą pala wierconego. W poprzednich publikacjach, autor wykazał, że iniekcja ta w głównej mierze uaktywnia zwiększone opory gruntu wzdłuż pobocznicy pala. Na tej podstawie w niniejszym artykule zaprezentowano procedurę obliczeniową prognozowania krzywą osiadania pala wierconego z iniekcją ciśnieniową pod podstawą. Przedstawiono...
-
ASSESSMENT OF CLIFF STABILITY AFTER THE DEMOLITION OF THE ENGINEERING FACILITIES
PublikacjaAs a part of an experiment, cliff in Gdynia Redlowo (southern coast of Baltic Sea, Gdansk Bay) was measured using terrestrial laser scanner. The main reason for taking up the subject of the Orlowo Cliff’s stability was a decision about controlled removal one of the war fortification elements. The main purpose of that analysis was to specify suitability of laser scanning in determination of slope’s stability after a violent event....