Wyszukiwarka
Filtry
wszystkich: 1660
wybranych: 1460
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: OFFSHORE STRUCTURES,DESIGN CALCULATIONS,SEA LOADING,STRESS EVALUATION,FEM
-
Textile reinforced concrete members subjected to tension, bending, and in-plane loads: Experimental study and numerical analyses
PublikacjaTextile reinforced concrete has raised increasing research interest during the last years, mainly due to its potential to be used for freeform shell structures involving complex load situations. Yet, most experimental work has focused on test setups with primarily uniaxial loading. In the current work, such setups are complemented with a novel test setup of deep beams, including in-plane bending and shear. Further, nonlinear finite...
-
Degradation of stiffness of building columns exposed to bending and impact load during ground motions
PublikacjaThe safety of civil engineering structures under external loads, including ground motions, is one of the issues related to the idea of sustainable society. The earthquake-induced soft-storey failure is a typical type of damage observed in buildings due to seismic excitation. The failure of an intermediate soft storey of a structure results in large vertical impact loading acting on the lower floors due to the fall of the upper...
-
Numerical analysis of mechanical properties of an infill structure used in 3D printings
PublikacjaThe paper presents results of a numerical analysis focused on an identification of mechanical properties of an element created by using Fused Deposition Modelling additive manufacturing technique (FDM). There is presented a description of technology of the 3D printing, numerical model created by using the finite element method (FEM), as well as some problems referred to estimation of the mechanical properties of the printout. The...
-
A Model-Order Reduction Approach for Electromagnetic Problems With Nonaffine Frequency Dependence
PublikacjaThe aim of this paper is to present a novel model-order reduction (MOR) technique for the efcient frequency-domain nite-element method (FEM) simulation of microwave components. It is based on the standard reduced-basis method, but the subsequent expansion frequency points are selected following the so-called sparsied greedy strategy. This feature makes it especially useful to perform a fast-frequency sweep of problems that lead...
-
Crystal structure and physical properties of AePd1-xP1+x (Ae = Ca, Sr)
PublikacjaWe report the discovery of two new compounds AePd1-xP1+x (Ae = Ca, Sr) crystallized in different hexagonal structures. Single crystals of AePd1-xP1+x (Ae = Ca, Sr) are obtained using the Bi-flux method. Crystallographic analysis by both powder and single crystal X-ray diffraction shows that CaPd1-xP1+x crystallizes in a non-centrosymmetric hexagonal structure with the space group P-6m2 (No.187) and lattice parameters a = b = 4.0391(9)...
-
Linear-scaling calculation of Hartree-Fock exchange energy with Non-orthogonal Generalised Wannier Functions
PublikacjaWe present a method for the calculation of four-centre two-electron repulsion integrals in terms of localised non-orthogonal generalised Wannier functions (NGWFs). Our method has been imple- mented in the ONETEP program and is used to compute the Hartree-Fock exchange energy component of Hartree-Fock and Density Functional Theory (DFT) calculations with hybrid exchange-correlation functionals. As the NGWFs are optimised in situ...
-
COMPARISON OF INVESTMENT PERFORMANCE MEASURES USING THE EXAMPLE OF SELECTED STOCK EXCHANGES
PublikacjaIn the following paper, the main objective is to examine whether the selection of the performance measure influences the evaluation of individual investments and the performance rankings generated on that basis. This study presents the values of 16 performance indicators along with their detailed descriptions. All calculations were made using the R program, and the source code can be found at the end of the article. Nine selected...
-
Axial capacity of steel built-up battened columns
PublikacjaThis paper deals with the numerical investigation aimed to study the axial capacity of pin-ended steel built-up columns. Three methods of calculating forces in chords and batten, taking into account the material and geometric imperfections specified in the Eurocode 3 are considered. The aim of this study was to compare different methods allowing the calculation of the column load capacity and determine a simpler and faster method...
-
Cost-Efficient EM-Driven Size Reduction of Antenna Structures by Multi-Fidelity Simulation Models
PublikacjaDesign of antenna systems for emerging application areas such as the Internet of Things (IoT), fifth generation wireless communications (5G), or remote sensing, is a challenging endeavor. In addition to meeting stringent performance specifications concerning electrical and field properties, the structure has to maintain small physical dimensions. The latter normally requires searching for trade-off solutions because miniaturization...
-
Wave Frequency Effects on Damage Imaging in Adhesive Joints Using Lamb Waves and RMS
PublikacjaStructural adhesive joints have numerous applications in many fields of industry. The gradual deterioration of adhesive material over time causes a possibility of unexpected failure and the need for non-destructive testing of existing joints. The Lamb wave propagation method is one of the most promising techniques for the damage identification of such connections. The aim of this study was experimental and numerical research on...
-
Investigating the effects of structural pounding on the seismic performance of adjacent RC and steel MRFs
PublikacjaAn insufficient separation distance between adjacent buildings is the main reason for structural pounding during severe earthquakes. The lateral load resistance system, fundamental natural period, mass, and stiffness are important factors having the influence on collisions between two adjacent structures. In this study, 3-, 5- and 9-story adjacent reinforced concrete and steel Moment Resisting Frames (MRFs) were considered to investigate...
-
A Family of Pb-based Superconductors with Variable Cubic to Hexagonal Packing
PublikacjaWe describe three previously unreported superconductors, BaPb3, Ba0.89Sr0.11Pb3, and Ba0.5Sr0.5Pb3. These three materials, together with SrPb3, form a distinctive isoelectronic family of intermetallic superconductors based on the stacking of Pb planes, with crystal structures that display a hexagonal to cubic perovskite-like progression, as rarely seen in metals. The superconducting transition temperatures (Tc) are similar for...
-
Phosphinoborenium cations stabilized by N-heterocyclic carbenes: synthesis, structure, and reactivity
PublikacjaPhosphinoborenium cations stabilized by N-heterocyclic carbenes (NHCs) were synthesized via the reaction of bromo(phosphino)boranes with NHCs. Their structures were investigated by heteronuclear magnetic resonance spectroscopy, X-ray diffraction, and density functional theory calculations. They possess a planar trigonal boron center directly bonded with the pyramidal phosphanyl group (PR2) and can be treated as cationic phosphinoboranes....
-
Ab initio study of formic acid monomer, dimer and trimer
PublikacjaConfigurations of the formic acid monomer, dimer and trimer are presented. The total energies for these structures have been calculated while the negatively charged clusters were considered and the possible pathways of interaction of low energy electrons with monomers and clusters were discussed. Calculations have been executed using 6-311 G** and 6-311 ++G** basis sets. The electron affinities of monomer and clusters are presented....
-
Modelling of high frequency dynamic responses of engineering structures
PublikacjaModelling of high frequency dynamic responses of engineering structures, especially those related to wave propagation, is a real numerical challenge. Nowadays most of numerical models, used for that purpose, are based on the application of various finite element techniques. However, finite element discrete models may also be considered as possessing certain periodic structures, which may manifest themselves in particular scenarios....
-
Some aspects of the constitutive modelling of natural fine grained soils
PublikacjaThe monograph deals with selected problems of the constitutive modelling of natural fine grained soils commonly known as clays. The main idea is not to propose a unified model which is capable of describing all known features of mechanical behaviour of fine grained soils. Instead, separate models are proposed describing the mechanical behaviour of heavily overconsolidated, lightly overconsolidated and normally consolidated clays....
-
Schemat powstawania rys na przykładzie osiowo rozciąganego pręta żelbetowego
PublikacjaW artykule przedstawiono w sposób schematyczny ideę powstawania kolejnych rys w konstrukcjach żelbetowych na przykładzie osiowo rozciąganego pręta. Opisano początkowy oraz końcowy stan zarysowania. Wyprowadzono wzór na szerokość rysy. Przedstawiono interpretację geometryczną rys dla fazy początkowego zarysowania oraz efekt tension stiffening na przykładzie elementu osiowo rozciąganego. Przedstawiono przykładowe obliczenia miary...
-
A Novel Versatile Decoupling Structure and Expedited Inverse-Model-Based Re-Design Procedure for Compact Single-and Dual-Band MIMO Antennas
PublikacjaMultiple-input multiple-output (MIMO) antennas are considered to be the key components of fifth generation (5G) mobile communications. One of the challenges pertinent to the design of highly integrated MIMO structures is to minimize the mutual coupling among the antenna elements. The latter arises from two sources, the coupling in the free space and the coupling currents propagating on a ground plane. In this paper, an array of...
-
Redesign of the Research Platform for Monitoring, Control and Security of Critical Infrastructure Systems
PublikacjaCritical Infrastructure Systems (CISs) play a key role in modern societies. Their sustainable operation depends heavily on the performance of dedicated structures and algorithms targeting monitoring, control and security aspects. In previous work a Research Platform (RP) for the design and simulation of such systems was presented. This works updates the information on the RP through the description of major hardware and software...
-
Injectable poloxamer/graphene oxide hydrogels with well‐controlled mechanical and rheological properties
PublikacjaAlthough significant progress has been made in the design and application of injectable hydrogels for biomedical applications, concurrent control of rheological and mechanical properties of injectable hydrogels has remained as an open challenge to the researchers. In this work, we introduce and put into practice a photo‐curable poloxamer (also known as Pluronic)/graphene oxide (Plu/GO) injectable hydrogel with well‐controlled rheological...
-
Optimization of the Hardware Layer for IoT Systems using a Trust Region Method with Adaptive Forward Finite Differences
PublikacjaTrust-region (TR) algorithms represent a popular class of local optimization methods. Owing to straightforward setup and low computational cost, TR routines based on linear models determined using forward finite differences (FD) are often utilized for performance tuning of microwave and antenna components incorporated within the Internet of Things systems. Despite usefulness for design of complex structures, performance of TR methods...
-
On Fast Multi-objective Optimization of Antenna Structures Using Pareto Front Triangulation and Inverse Surrogates
PublikacjaDesign of contemporary antenna systems is a challenging endeavor, where conceptual developments and initial parametric studies, interleaved with topology evolution, are followed by a meticulous adjustment of the structure dimensions. The latter is necessary to boost the antenna performance as much as possible, and often requires handling several and often conflicting objectives, pertinent to both electrical and field properties...
-
Expedited Acquisition of Database Designs for Reduced-Cost Performance-Driven Modeling and Rapid Dimension Scaling of Antenna Structures
PublikacjaFast replacement models have been playing an increasing role in high-frequency electronics, including the design of antenna structures. Their role is to improve computational efficiency of the procedures that normally entail large numbers of expensive full-wave electromagnetic (EM) simulations, e.g., parametric optimization or uncertainty quantification. Recently introduced performance-driven modeling methods, such as the nested...
-
ANALYSIS OF THE IMPACT OF MASS FLOW EXTRACTION ON THE CHANGE OF PARAMETERS IN A LABYRINTH SEAL USING THE STODOLA METHOD
PublikacjaLabyrinth seals are an important element of a steam turbine set design. The use of diagnostic extraction makes it possible to control the operation of a seal by providing information on the thermodynamic parameters along the length of the seal. Diagnostic extraction has a considerable impact on the change of the parameters, the amount of the extracted mass. This article describes the dependence of pressure in the clearance downstream...
-
ANALYSIS OF THE IMPACT OF MASS FLOW EXTRACTION ON THE CHANGE OF PARAMETERS IN A LABYRINTH SEAL USING THE STODOLA METHOD
PublikacjaLabyrinth seals are an important element of a steam turbine set design. The use of diagnostic extraction makes it possible to control the operation of a seal by providing information on the thermodynamic parameters along the length of the seal. Diagnostic extraction has a considerable impact on the change of the parameters, the amount of the extracted mass. This article describes the dependence of pressure in the clearance downstream...
-
Stability of cylindrical steel silos composed of corrugated sheets and columns based on FE analyses versus Eurocode 3 approach
PublikacjaComprehensive static and dynamic 3D stability finite element analyses of a cylindrical steel silo composed of corrugated sheets and open thin-walled vertical stiffener profiles were carried out by taking the geometric and material non-linearity into account. The silowas subjected to axisymmetric and non-axisymmetric loads imposed by a bulk solid following Eurocode 1. Theoretical and measured initial geometric imperfections were...
-
Accelerated multi-objective design optimization of antennas by surrogate modeling and domain segmentation
PublikacjaMulti-objective optimization yields indispensable information about the best possible design trade-offs of an antenna structure, yet it is challenging if full-wave electromagnetic (EM) analysis is utilized for performance evaluation. The latter is a necessity for majority of contemporary antennas as it is the only way of achieving acceptable modeling accuracy. In this paper, a procedure for accelerated multi-objective design of...
-
Universal autonomous control and management system for multipurpose unmanned surface vessel
PublikacjaThe paper presents design, structure and architecture of the Universal Autonomous Control and Management System (UACAMS) for multipurpose unmanned surface vessel. The system was designed, installed and implemented on the multipurpose platform - unmanned surface vessel named HydroDron. The platform is designed to execute hydrographic survey missions with multi-variant configuration of the survey system (payload? ) including multi-beam...
-
Flexomagneticity in Functionally Graded Nanostructures
PublikacjaFunctionally graded structures have shown the perspective of materials in a higher efficient and consistent manner. This study reports a short investigation by concentrating on the flexomagnetic response of a functionally graded piezomagnetic nano-actuator, keeping in mind that the converse magnetic effect is only taken into evaluation. The rule of mixture assuming exponential composition of properties along with the thickness...
-
Effect of bending-torsion on fracture and fatigue life for 18Ni300 steel specimens produced by SLM
PublikacjaIn this study, different fracture surfaces caused by fatigue failure were generated from 18Ni300 steel produced by selective laser melting (SLM). Hollow round bars with a transverse hole were tested under bending-torsion to investigate the crack initiation mechanisms and fatigue life. Next, the post-failure fracture surfaces were examined by optical profilometer and scanning electron microscope. The focus is placed on the relationship...
-
A robust design of a numerically demanding compact rat-race coupler
PublikacjaA fast and accurate design procedure of a computationally expensive microwave circuit has been presented step-by-step and experimentally validated on the basis of a compact rat-race coupler (RRC) comprising slow-wave resonant structures (SWRSs). The final compact RRC solution has been obtained by means of a sequential optimization scheme exploiting the implicit space mapping (ISM) algorithm. A well-suited surrogate optimization...
-
Step on It Bringing Fullwave Finite-Element Microwave Filter Design up to Speed
PublikacjaThere are many steps in the design of a microwave filter: mathematically describing the filter characteristics, representing the circuit as a network of lumped elements or as a coupling matrix, implementing the distributed elements, finding the initial dimensions of the physical structure, and carrying out numerical tuning using electromagnetic (EM) simulators. The whole process is painstaking and time-consuming, and it requires...
-
Characterizing surface and air temperature in the Baltic Sea coastal area using remote sensing techniques and GIS
PublikacjaEstimation of surface temperature using multispectral imagery retrieved from satellite sensors constitutes several problems in terms of accuracy, accessibility, quality and evaluation. In order to obtain accurate results, currently utilized methods rely on removing atmospheric fluctuations in separate spectral windows, applying atmospheric corrections or utilizing additional information related to atmosphere or surface characteristics...
-
Rapid optimization of compact microwave passives using kriging surrogates and iterative correction
PublikacjaDesign of contemporary microwave components is—in a large part—based on full-wave electromagnetic (EM) simulation tools. The primary reasons for this include reliability and versatility of EM analysis. In fact, for many microwave structures, notably compact components, EM-driven parameter tuning is virtually imperative because traditional models (analytical or network equivalents) are unable to account for the cross-coupling effects,...
-
Nonlocal Models of Plates and Shells with Applications in Micro- and Nanomechanics
PublikacjaNowadays, the use of small-scale structures in micro/nanomachines has become more and more widespread. The most important applications of such small-sized parts are in micro-electro-mechanical systems (MEMS) as well as nano-electro-mechanical systems (NEMS) as actuators, sensors, energy harvesters. For example, nanosensors are nanoscale devices that measure physical quantities and convert these to signals that can be detected and...
-
Influence of separation gap on the structural response of colliding structures under earthquake excitation
PublikacjaThe high level of urbanization in the XXIst century forces the designers to design closely-separated structures and to take into account many factors influencing their response during seismic excitation, which are the most unpredictable loads which can affect civil engineering structures. Interactions between insufficiently adjacent buildings, known as the earthquake-induced structural pounding, may cause serious damage to the structures,...
-
Hybrid all-cellulose reinforcement in polypropylene matrix biocomposites for injection moulding - influence of particle geometry and volume fraction on hybrid effect
PublikacjaThe presented study is focused on evaluation of influence of reinforcement volume fraction and geometry on the occurrence of positive hybrid effect by the hybridisation of man-made cellulose fibres (rayon viscose) with cellulose microparticle fillers applied in polypropylene matrix. Four volume fractions of reinforcement were used at 1:1 combination of short man-made cellulose fibres with cellulose microfillers of different aspect...
-
Evaluation of reformer tubes degradation after long term operation
PublikacjaPurpose of this paper is to show the effect of long-term service at elevated temperatures on microstructural changes of cast steel reformer tubes made of the alloy IN-519 (24%Cr, 24%Ni, Nb). The relationship between mechanical properties and microstructure degradation is discussed. Investigations were performed on five tubes taken from ammonia reformer furnace. Tubes worked at temperature of 880C and 3,2 MPa pressure. The operation...
-
Wykorzystanie środowiska ekspertowego do projektowania wybranych podsystemów energetycznych statków
PublikacjaW artykule przedstawiono koncepcję wykorzystania badań symulacyjnych oraz systemu ekspertowego z bazą wiedzy do wspomagania projektowania podsystemów energetycznych statków. Opisano przykładową strukturą steru strumieniowego oraz poszczególne jej elementy składowe.This paper presents a concept of application of simulation investigations and an expert system with a knowledge-base and data-base to improve design procedures of a ship...
-
Analiza odcinków generujących straty czasu w transporcie tramwajowym
PublikacjaW czasie analiz i studiów przedwykonawczych dotyczących budowy nowych i modernizacji istniejących tras tramwajowych, bardzo często zakładane są nierealne czasy przejazdów, które weryfikuje się już po oddaniu linii do eksploatacji i przeprowadzeniu badań obserwacyjnych. Problematyczne wydaje się określenie, przed zakończeniem inwestycji, rzeczywistej prędkości jazdy, jak również strat czasu powstających w miejscach potencjalnych...
-
Generalized Chebyshev Bandpass Filters With Frequency-Dependent Couplings Based on Stubs
PublikacjaThis paper presents an accurate synthesis method for inline and cross-coupled generalized Chebyshev bandpass filters with frequency-dependent couplings implemented via open and short stubs. The technique involves the synthesis of a lumped-element prototy pe in the form of a coupling matrix with a frequency-dependent term and the conversion of this prototype to a distributed-element mode l composed of sections of TEM lines. This...
-
Effect of manufacturing errors of the pad sliding surface on the performance of the hydrodynamic thrust bearing
PublikacjaIn the present study, investigation of the effect of manufacturing errors on the performance of large tilting pad thrust bearings has been performed, following a CFD-based Thermohydrodynamic analysis of a single pad. A 3D model has been generated, including the pad, the lubricant film and the corresponding part of the collar. The pad has been assumed to be deformed about the pivot point, due to thrust loading. Manufacturing errors...
-
Inverse surrogate modeling for low-cost geometry scaling of microwave and antenna structures
PublikacjaPurpose–The purpose of this paper is to investigate strategies for expedited dimension scaling ofelectromagnetic (EM)-simulated microwave and antenna structures, exploiting the concept of variable-fidelity inverse surrogate modeling.Design/methodology/approach–A fast inverse surrogate modeling technique is described fordimension scaling of microwave and antenna structures. The model is established using referencedesigns obtained...
-
From Janus nanoparticles to multi-headed structure - photocatalytic H2 evolution
PublikacjaThe generation of stable, high-performance photocatalysts with appropriate charge distribution for solar energy conversion is currently one of the urgent missions of photocatalytic science. Recent studies have shown that the Janus NPs with characteristic varied, asymmetric structure may boost overall efficiency of photocatalys. However, there is still a lack of systematic studies in which Janus-type particles are used in the hydrogen...
-
Why Are Left-Handed G-Quadruplexes Scarce?
PublikacjaG-quadruplexes (G4s) are nucleic acid structures crucial for the regulation of gene expression and genome maintenance. While they hold promise as nanodevice components, achieving desired G4 folds requires understanding the interplay between stability and structural properties, like helicity. Although right-handed G4 structures dominate the experimental data, the molecular basis for this preference over left-handed helicity is unclear....
-
Testing of the longest span soil-steel bridge in Europe – new quality in measurements
PublikacjaThe article describes interdisciplinary and comprehensive diagnostic tests of final bridge inspection and acceptance proposed for a soil – steel bridge made of corrugated sheets, being the European span length record holder (25.74 m). As an effect of an original concept a detailed and precise information about the structure response was collected. The load test design was based on the nonlinear numerical simulations performed by...
-
Influence of Different Biofuels on the Efficiency of Gas Turbine Cycles for Prosumer and Distributed Energy Power Plants
PublikacjaThe efficiency of a gas turbine can be affected by the use of different biofuels usually with a relatively Lower Heating Value (LHV). The paper evaluates the impact of calorific value of fuel on turbine performance and analyzes the possibilities of optimizing turbine construction from the point of view of maximum efficiency for a particular fuel. The several variants of design of small power microturbines dedicated to various biofuels...
-
Influence of effective width of flange on calculation and reinforcement dimensioning of beam of reinforced concrete frame
PublikacjaThe paper analyses the influence of modelling the cross-section of a beam in two-storey reinforced concrete frame of industrial warehouse with dimensions: 18.0 m × 32.0 m using bar elements on the results of bending moments, the value of elastic deflection and the dimensioning of reinforcement due to bending. Six options were considered: a beam as a rectangular section and five T-beam variants with different definitions of effective...
-
An experimental study on polymer mass
PublikacjaA new method of repairing damaged structures by filling the cracks with specially prepared polymer mass has been recently proposed. The technique is mainly dedicated to historical objects where minimum intervention is permitted. The flexible joint bonds the disrupted elements and ensures further safe exploitation of a damaged structure. The aim of the present paper is to show the results of an experimental study on polymer mass...
-
Integrated Experimental and Theoretical Approach for Efficient Design and Synthesis of Gold-Based Double Halide Perovskites
PublikacjaApplied cutting-edge electronic structure and phonon simulations provide a reliable knowledge about the stability of perovskite structures and their electronic properties, which are crucial for design of effective nanomaterials. Gold is one of the exceptional elements, which can exist both as a monovalent and a trivalent ion in the B site of a double perovskite such as A2BI BIIIX6. However, until now, electronic properties of Cs2AuI AuIIIX6...