Filtry
wszystkich: 1518
wybranych: 1192
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: HARDWARE IN THE LOOP TESTING
-
A Low-Cost System for Far-Field Non-Anechoic Measurements of Antenna Performance Figures
PublikacjaPrototype measurements are the key step in the development of antenna structures. Typically, their far-field characteristics are validated in expensive, dedicated facilities such as open range sites, or anechoic chambers. Despite being necessary for obtaining high-precision data (e.g., for device qualification), the use of costly infrastructure might not be fully justified when the main goal of measurements includes demonstration...
-
STEROWNIK MIKROSIECI ELEKTROENERGETYCZNEJ
PublikacjaW artykule rozpatruje się konstrukcję sterownika mikrosieci elektroenergetycznej. Sterownik zarządza zasobamienergii elektrycznej w celu pokrycia zapotrzebowania lokalnych gospodarstw domowych z uwzględnieniem kwestii ekonomicznych. Przedstawiono strukturę sterowania, zdefiniowano zadanie optymalizacji, dokonano badań symulacyjnych dla przykładowej mikrosieci o zróżnicowanych sposobach generowania i magazynowania. Zaproponowano...
-
A universal method for the identification of genes encoding amatoxins and phallotoxins in poisonous mushrooms
PublikacjaABSTRACT Background. As the currently known diagnostic DNA targets amplified in the PCR assays for detection of poisonous mushrooms have their counterparts in edible species, there is a need to design PCR primers specific to the genes encoding amanitins and phallotoxins, which occur only in poisonous mushrooms. Objective. The aim of the study was testing of PCR-based method for detection of all genes encoding hepatotoxic cyclic...
-
Pose classification in the gesture recognition using the linear optical sensor
PublikacjaGesture sensors for mobile devices, which have a capability of distinguishing hand poses, require efficient and accurate classifiers in order to recognize gestures based on the sequences of primitives. Two methods of poses recognition for the optical linear sensor were proposed and validated. The Gaussian distribution fitting and Artificial Neural Network based methods represent two kinds of classification approaches. Three types...
-
APPLICATION POSSIBILITIES OF THE S960 STEEL IN UNDERWATER WELDED STRUCTURES
PublikacjaIn this paper, the application possibilities of the ultra-high strength (UHSS). Domex 960 steel in the underwater welded structures are analyzed. In the research, the investigated material has been tested in bead-on-plate wet welding conditions with the usage of different heat input values, namely 0.63 kJ/mm, 0.72 kJ/mm and 0.93 kJ/mm. Specimens were performed by the manual metal arc (MMA) welding method with the usage of rutile...
-
JamesBot - an intelligent agent playing StarCraft II
PublikacjaThe most popular method for optimizing a certain strategy based on a reward is Reinforcement Learning (RL). Lately, a big challenge for this technique are computer games such as StarCraft II which is a real-time strategy game, created by Blizzard. The main idea of this game is to fight between agents and control objects on the battlefield in order to defeat the enemy. This work concerns creating an autonomous bot using reinforced...
-
An Attempt to Create Speech Synthesis Model That Retains Lombard Effect Characteristics
PublikacjaThe speech with the Lombard effect has been extensively studied in the context of speech recognition or speech enhancement. However, few studies have investigated the Lombard effect in the context of speech synthesis. The aim of this paper is to create a mathematical model that allows for retaining the Lombard effect. These models could be used as a basis of a formant speech synthesizer. The proposed models are based on dividing...
-
Surface Texture Analysis of Hardened Shafts after Ceramic Ball Burnishing
PublikacjaThis article represents the results of testing the surface condition of shafts manufactured by the burnishing process. The shafts with a hardness of approximately 62 HRC (Rockwell C). were burnished with a ceramic ball (Si3N4), where the force range was controlled by the means of a hydraulic system. The machining process consisted of hard turning shafts with cubic boron nitride (CBN) inserts, followed by burnishing with the use...
-
Towards a Lightweight Approach for the Evaluation of Requirements Engineering Impact on Other IT Project Areas
PublikacjaRequirements Engineering (RE) is recognized as one of the most important, but difficult areas of software engineering, with a significant impact on other areas of the IT project and its final outcome. The empirical studies investigating this impact are hard to conduct, mainly due to large effort required. It is thus difficult for researchers and even more for industry practitioners to make evidence-based evaluations, how decisions...
-
The Usefulness of Cyclic Diamidines with Different Core-substituents as Antitumor Agents
PublikacjaA series of related polycationic compds. has been screened for potential antitumor activity by the NCI's in vitro testing (one dose primary anticancer assay and the NCI-60 full panel screening). The GI50 values of triazines 3 and 4 are on av. 1.9 μM and 2.4 μM, resp. Furan 8 deserves mention too (1.9 μM). The biol. test results showed that carbazole 10 possessed cytotoxic activity in the nanomolar range, much better than...
-
Multivariate analysis of impedance data obtained for coating systems of varying thickness applied on steel
PublikacjaElectrochemical impedance spectroscopy (EIS) has proven to be a valuable test method for the electrochemical characterization of protective coatings on metals. The common way of analysis in impedance spectroscopy is to model the impedance spectrum by means of an equivalent circuit and to extract the quantity of interest using optimization techniques. A model, corresponding to the behavior of the sample under testing, is important...
-
TASTE QUALITIES ESTIMATION BY TASTE SENSE AND ELECTROCHEMICAL SENSORS
PublikacjaThe principles of taste sense and kinds of tastes (sweet, salty, sour, bitter, umami and fat) have been described. Food quality estimation by taste sense: organoleptic testing and sensory analysis has been presented. The principle of operation of potentiom etric sensor composed of several Ion Selective Electrodes or All Solid State Electrodes with polymeric membranes and macromolecular chemical compounds sensitive to substances...
-
Designate CTOD of Weld Metal of butt weld, No WOiO/II/108/2013
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
Influence of low-temperature physical hardening on stiffness and tensile strength of asphalt concrete and stone mastic asphalt
PublikacjaThis paper presents laboratory testing of stiffness modulus and indirect tensile strength of three asphalt concrete (AC) and three stone mastic asphalt (SMA) mixes after isothermal storage at temperature of -20oC, at different time intervals up to 16 days. The tests under repeated dynamic loading showed physical hardening of all tested mixes which was manifested by an evident increase of their stiffness moduli after isothermal...
-
Designate CTOD Heat Affected Zone of butt weld, Report No: WOiO/II/76/2013
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
Cooperation of ORC installation with a gas boiler as a perspective co-generation system for households
PublikacjaThis paper reports tests of an innovative micro-CHP unit prototype, consisting of a traditional gas boiler and organic Rankine cycle (ORC), which incorporates original system components such as an axial vapour microturbine, evaporator and condenser. The system co-generates heat and electricity for a single household or a group of households. Electricity is only a by-product during production of heat. While testing the prototype,...
-
DETERMINING THE TIME CONSTANT USING TWO METHODS AND DEFINING THE THERMOCOUPLE RESPONSE TO SINE EXCITATION OF GAS TEMPERATURE
PublikacjaThis paper describes the two methods of determining the time constant of type K thermocouple, for two construction solutions: the exposed weld and the mantle fillet weld. This is an important parameter indicating the response time of the thermocouple on the recorded signal. The first method consists of determining the value of τ in the way of numerical simulation of heat exchange between the thermocouple and the current of gas...
-
ANALYSIS OF CLIMATIC ZONES IN POLAND WITH REGARD TO ASPHALT PERFORMANCE GRADING
PublikacjaTowards the end of the last century a new system of bitumen grading was developed and implemented as part of the American Strategic Highway Research Program (SHRP). Its aim was to better adjust the testing methods and requirements for road bitumens to the actual conditions in which those bitumens serve in road pavements. Currently in Poland, similarly as in the other EU countries, road bitumens are tested and classified with regard...
-
Two-Dimensional Gas Chromatography Coupled With Mass Spectrometry in Food Analysis
PublikacjaThe development of instrumental analytical techniques provided the opportunity for in-depth characterization of many food matrices. In particular, the use of gas chromatography coupled with mass spectrometry gives impressive results in terms of quality and authenticity testing, conducting food freshness evaluations and contamination assessments. A new variant of gas chromatography, namely two-dimensional gas chromatography (GC...
-
Influences of grain shape and size distribution on permeability
PublikacjaThe present study investigates the effects of shape and size distributions of grains on the coefficient of permeability (k). A series of constant head permeability tests were performed to characterize the coefficient of permeability. Three particle size ranges (4.75- 0.075, 1.18- 0.075 and 0.300-0.075 mm) of two different sands (Narli Sand, Crushed Stone Sand) having different shapes were tested in a constant head permeability...
-
EXPERIMENTAL RESEARCH ON INFLUENCE OF THE FUEL NOZZLE GEOMETRY ON THE FUEL CONSUMPTION OF THE MARINE 4-STROKE DIESEL ENGINE
PublikacjaThe article presents experimental research that has been carried out on a marine, 4-stroke, 3-cylinder, turbocharged engine. During testing, the engine operated at a constant rotational speed of 750 rpm and a load from 0 kW to 280 kW. The engine was fuelled by diesel oil of known specification and loaded by electric generator with water resistance. The fuel consumption was measured during the engine operation with fuel nozzles...
-
Programmatic Simulation of Laser Scanning Products
PublikacjaThe technology of laser scanning is widely used for producing three-dimensional digital representations of geographic features. The measurement results are usually available in the form of 3D point clouds, which are often used as a transitional data model in various remote sensing applications. Unfortunately, while the costs of Light Detection And Ranging scanners have dropped significantly in recent years, they are still considered...
-
CTOD designation for WM and HAZ in butt joint made from S460 ML steel, Expertise No. WOiO/II/82/2015
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
Development of potential candidate reference materials for drugs in bottom sediment, cod and herring tissues
PublikacjaRegular use of a reference material and participation in a proficiency testing program can improve the reliability of analytical data. This paper presents the preparation of candidate reference materials for the drugs metoprolol, propranolol, carbamazepine, naproxen, and acenocoumarol in freshwater bottom sediment and cod and herring tissues. These reference materials are not available commercially. Drugs (between 7 ng/g and 32...
-
Designate of CTOD for WM and HAZ, report no: WOiO/II/122/2014
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
The effect of tire aging on acoustic performance of CPX reference tires
PublikacjaReduction of tire/road noise is one of the biggest environmental challenges of road traffic. To reduce that noise it is necessary to perform acoustic measurements on the base of wellproven standard procedures. One method of measurements that is in common use, namely the Close Proximity Method (CPX), is described in standard ISO-DIS 11819-2. As this method is used to classify road surfaces regarding their influence on vehicle noise,...
-
Pressure drop and heat transfer during boiling and condensation at subcritical region
PublikacjaMost of the data presented in the literature relate to saturation temperatures in the range - 20°C to 40°C due to the application in refrigeration technology. There is necessity to extend databases to higher values of saturation temperature due to new applications such as Organic Rankine Cycle and high temperature heat pumps. Only few papers contain data for high reduced pressure for low boiling point liquids. This paper focus...
-
Determination of the tram track axis using a multi receiver GNSS measurement system
PublikacjaThis article refers to research, that has been conducted by an interdisciplinary research team from the Gdańsk University of Technology and the Maritime University in Gdynia since 2009. These investigation concerns the determination of a railway track axis using the mobile satellite measurement technique. Following the dynamic development of GNSS techniques, that could be seen in the last decade, the team carried out further experiments...
-
Numerical modelling of the mesofracture process of sintered 316L steel under tension using microtomography
PublikacjaThis paper concerns numerical modelling of the deformation process, taking into account the local fracture of porous 316L sinters at the mesoscopic scale using the finite element method. Calculations are performed with the use of geometrical models, to map the realistic shape of the porous mesostructure of the material, obtained by means of computed microtomography. The microtomographic device has limited and insufficient measurement...
-
Methodology of research on the impact of ramp metering on the safety and efficiency of road traffic using transport models
PublikacjaThe methods currently used to assess the impact of Intelligent Transport Systems (ITS) services on traffic safety and efficiency are mainly based on expert assessments, statistical studies or traffic models that need further development. There is no structured, uniform evaluation method to compare the impact of different ITS services and their different configurations. The impact of ITS deployment on the road network adjacent to...
-
Toward Robust Pedestrian Detection With Data Augmentation
PublikacjaIn this article, the problem of creating a safe pedestrian detection model that can operate in the real world is tackled. While recent advances have led to significantly improved detection accuracy on various benchmarks, existing deep learning models are vulnerable to invisible to the human eye changes in the input image which raises concerns about its safety. A popular and simple technique for improving robustness is using data...
-
Auto-tuning methodology for configuration and application parameters of hybrid CPU + GPU parallel systems based on expert knowledge
PublikacjaAuto-tuning of configuration and application param- eters allows to achieve significant performance gains in many contemporary compute-intensive applications. Feasible search spaces of parameters tend to become too big to allow for exhaustive search in the auto-tuning process. Expert knowledge about the utilized computing systems becomes useful to prune the search space and new methodologies are needed in the face of emerging heterogeneous...
-
A prototype information system for managing and pricing e-waste
PublikacjaThere is no doubt that innovation drives development in all areas of human activity, including electrical and electronic equipment. However, the production of new equipment has a significant impact on the natural environment and a relatively high consumption of natural resources. To address these issues, the circular economy has been implemented in recent years by promoting and introducing numerous measures to facilitate the recycling...
-
Improved maximum power point tracking algorithms by using numerical analysis techniques for photovoltaic systems
PublikacjaSolar photovoltaic (PV) panels generate optimal electricity when operating at the maximum power point (MPP). This study introduces a novel MPP tracking algorithm that leverages the numerical prowess of the predictor-corrector method, tailored to accommodate voltage and current fluctuations in PV panels resulting from variable environmental factors like solar irradiation and temperature. This paper delves into the intricate dynamics...
-
Unsupervised Learning for Biomechanical Data Using Self-organising Maps, an Approach for Temporomandibular Joint Analysis
PublikacjaWe proposed to apply a specific machine learning technique called Self-Organising Maps (SOM) to identify similarities in the performance of muscles around human temporomandibular joint (TMJ). The performance was assessed by measuring muscle activation with the use of surface electromyography (sEMG). SOM algorithm used in the study was able to find clusters of data in sEMG test results. The SOM analysis was based on processed sEMG...
-
Hydrazinolysis Products of Selected Sugar Lactones—Crystal Structure and Microbiological Activity
PublikacjaCommercially available lactones, as well as those synthesized by us, turned out to be good substrates for the synthesis of sugar hydrazides. The exception was L-ascorbic acid, whose hydrazinolysis led to the formation of a hydrazinium salt, not the hydrazide as expected. The structure of all compounds was confirmed by NMR and X-ray analyses. The lower durability of hydrazinium L-ascorbate was additionally confirmed by thermogravimetric...
-
Virtual tour as an innovative tool for architectural education - from understanding heritage to creativity stimulation
PublikacjaThe article presents the potential of the virtual tour in architectural education as an innovative tool to better understand heritage and stimulate creativity. A methodology for creating a virtual tour based on a point cloud obtained from a survey based on 360° camera images is presented. Two different purposes for the use of point clouds are presented from reliable indicators of heritage documentation useful for digital twin modelling...
-
Low-volume label-free SARS-CoV-2 detection with the microcavity-based optical fiber sensor
PublikacjaAccurate and fast detection of viruses is crucial for controlling outbreaks of many diseases; therefore, to date, numerous sensing systems for their detection have been studied. On top of the performance of these sensing systems, the availability of biorecognition elements specific to especially the new etiological agents is an additional fundamental challenge. Therefore, besides high sensitivity and selectivity, such advantages...
-
Conserved motifs of MutL proteins
PublikacjatThe MutL protein is best known for its function in DNA mismatch repair (MMR). However, there isevidence to suggest that MutL is not only the linker connecting the functions of MutS and MutH in MMR,but that it also participates in other repair systems, such as Very Short Patch (VSP), Base Excision (BER)and Nucleotide Excision Repair (NER). This study set out to identify the most highly conserved aminoacid sequence motifs in MutL...
-
Proportional-Derivative and Model-based Controllers used for a Serial Type Manipulator in case of a Variable Mass Payload
PublikacjaIn the paper, numerical analysis of dynamics of a variable mass system is considered. Its reference example is a serial-like manipulator composed of revolute joints and rigid bodies. Payload of its gripper is considered as its variable mass element (mass and inertia irregularly between subsequent payloads). For the rest of the system, inertia parameters are considered as known (precisely identified during the assembling process)....
-
Fast and reliable knowledge-based design closure of antennas by means of iterative prediction-correction scheme
PublikacjaA novel framework for expedited antenna optimization with an iterative prediction-correction scheme is proposed. The methodology is comprehensively validated using three real-world antenna structures: narrow-band, dual-band and wideband, optimized under various design scenarios. The keystone of the proposed approach is to reuse designs pre-optimized for various sets of performance specifications and to encode them into metamodels...
-
From ashes to porous hierarchical nanocarbon electrode: Upcycling secondary waste materials through self-catalytic chemical vapour deposition
PublikacjaMetal and metal oxide particles are abundant in various ash-based wastes. Utilizing these as catalyst sources for the fabrication of carbon nanomaterials could present a valuable approach to reduce our reliance on non-renewable and costly catalyst sources, thereby facilitating large-scale nanomaterial production. In this context, secondary waste materials (SWMs) are by-products resulting from the (complete or partial) combustion...
-
Microstructure and mechanical properties of a dissimilar metal welded joint of Inconel 617 and P92 steel with Inconel 82 buttering layer for AUSC boiler application
PublikacjaThe application of the novel dissimilar metal welded (DMW) joint, utilizing Inconel 617 and P92 steel, was showcased in the advanced ultra-supercritical (AUSC) boiler. The work has been performed to investigate the effect of Inconel 82 (ERNiCr-3) buttering layer on microstructure and mechanical properties (high-temperature tensile strength, impact strength and microhardness) of gas tungsten arc welded (GTAW) dissimilar joint between...
-
ZASTOSOWANIE APLIKACJI INTERNETOWEJ W OCENIE JAKOŚCI DOPASOWANIA APARATÓW SŁUCHOWYCH
PublikacjaW pracy opisano zastosowanie aplikacji internetowej do oceny jakości dopasowania aparatów słuchowych. Metoda oceny polega na badaniu ankietowym, uzupełnionym testem rozumienia słów jednosylabowych w polu swobodnym. Opisywana aplikacja internetowa pozwala na przeprowadzenie badania z dowolnego komputera z dostępem do sieci. Dzięki implementacji metody w postaci aplikacji internetowej, można w systematyczny i uporządkowany sposób...
-
NADZOROWANIE WYPOSAŻENIA DO MONITOROWANIA I POMIARÓW WEDŁUG WYMAGAŃ WYBRANYCH NORM ORAZ PRZEPISÓW PRAWNYCH
Publikacja: Przyrządy pomiarowe stanowią zasadniczy element złożonego systemu oceny jakości wyrobów na wszystkich etapach produkcji. Odpowiednio zaprojektowane procedury opisujące procesy kontrolne i pomiarowe, sprawnie zorganizowane i przeprowadzane operacje monitorowania i pomiarów parametrów procesów i produktów oraz skutecznie funkcjonujący nadzór nad wyposażeniem do monitorowania i pomiarów w organizacji są podstawą do wykazania, że...
-
Akcelerator predykcji wewnątrzramkowej H.264 do kompresji obrazu w sensorach wizyjnych
PublikacjaW komunikacie przedstawiono konfigurowalny cyfrowy akcelerator predykcji wewnątrzramkowej przeznaczony dla enkodera wideo standardu H.264. Akcelerator realizuje predykcję typu „intra” dla makrobloków luminancji o wymiarach 4x4 i 16x16. Akcelerator wstępnie zaimplementowano w układzie FPGA, gdzie został on pomyślnie zweryfikowany, a następnie zaimplementowano go w układzie ASIC w technologii UMC 90 nm. Szczegółowe wyniki testów...
-
Akcelerator predykcji wewnątrzramkowej H.264 do kompresji obrazu w sensorach wizyjnych
PublikacjaW artykule przedstawiono konfigurowalny cyfrowy akcelerator predykcji wewnątrzramkowej przeznaczony dla enkodera wideo standardu H.264. Akcelerator realizuje predykcję typu „intra” dla makrobloków luminancji o wymiarach 4x4 i 16x16. Akcelerator wstępnie zaimplementowano w układzie FPGA, gdzie został on pomyślnie zweryfikowany, a następnie zaimplementowano go w układzie ASIC w technologii UMC 90 nm. Szczegółowe wyniki testów akceleratora...
-
Badania stanu technicznego ścianek szczelnych strony południowej i północnej komory południowej śluzy Dzierżno
PublikacjaPrace dotyczyły badań nieniszczących łączników (zamków) Paine`a oraz ścianek szczelnych. Ściany boczne komory południowej śluzy Dzierżno zbudowane są ze stalowych pasów blachy o grubości około 16mm i długości 22m połączonych ze sobą wzdłuż dłuższej krawędzi za pomocą zamków Peine`a. System ten umożliwia uzyskanie szczelnego połączenia na całej długości ścianki. Zaawansowany proces korozji spowodował rozszczelnienie połączenia...
-
Musical Instrument Tagging Using Data Augmentation and Effective Noisy Data Processing
PublikacjaDeveloping signal processing methods to extract information automatically has potential in several applications, for example searching for multimedia based on its audio content, making context-aware mobile applications (e.g., tuning apps), or pre-processing for an automatic mixing system. However, the last-mentioned application needs a significant amount of research to reliably recognize real musical instruments in recordings....
-
EXPERIENCE-ORIENTED SMART EMBEDDED SYSTEM
PublikacjaThe Experience-Oriented Smart Embedded System (EOSES) is proposed as a new technological platform providing a common knowledge management approach that allows mass embedded systems for experiential knowledge capturing, storage, involving, and sharing. Knowledge in the EOSES is represented as SOEKS, and organized as Decisional DNA. The platform is mainly based on conceptual principles from Embedded Systems and Knowledge Management....