Filtry
wszystkich: 162
wybranych: 144
Wyniki wyszukiwania dla: model assembly
-
Cooperativity of Halogen- and Chalcogen-Bonding Interactions in the Self-Assembly of 4‑Iodoethynyl- and 4,7-Bis(iodoethynyl)benzo-2,1,3-chalcogenadiazoles: Crystal Structures, Hirshfeld Surface Analyses, and Crystal Lattice Energy Calculations
PublikacjaSeveral new 4-iodoethynyl- and 4,7-bis- (iodoethynyl)benzo-2,1,3-chalcogenadiazoles were prepared, and a comprehensive analysis of the most prominent secondary bonding interactions responsible for the crystal self-assembly was performed using X-ray diffraction. The presence of both the iodoethynyl and chalcogenadiazole moieties allows an evaluation of the preference of these molecules to aggregate through either chalcogen- or halogen-bonding...
-
Failure mode prediction for composite structural insulated panels with MgO board facings
PublikacjaSandwich panels are readily used in civil engineering due to their high strength to weight ratio and the ease and speed of assembly. The idea of a sandwich section is to combine thin and durable facings with a light-weight core and the choice of materials used allows obtaining the desired behaviour. Panels in consideration consist of MgO (magnesium oxide) board facings and expanded polystyrene core and are characterized by immunity...
-
QUASI-DISTRIBUTED NETWORK OF LOW-COHERENCE FIBER-OPTIC FABRY-PÉROT SENSORS WITH CAVITY LENGTH-BASED ADDRESSING
PublikacjaDistributed measurement often relies on sensor networks. In this paper, we present the construction of low coherent fiber-optic Fabry-Pérot sensors connected into a quasi-distributed network. We discuss the mechanism of spectrum modulation in this type of sensor and the constraints of assembly of such sensors in the network. Particular attention was paid to separate the signals from individual sensors, which can be achieved by...
-
Influence of bush wear in water lubricated marine stern tube bearings with shaft misalignment
PublikacjaWater lubricated propeller shaft bearings are frequently employed on modern ships due to their advantages such as durability, simplicity and low price. Specific working conditions on ships cause shaft misalignment which often results in rapid wearing of bush and shaft. Shaft misalignment could be an effect of manufacturing or assembly faults but sometimes it appears due to hull or shaft deformation. The wearing process has influence...
-
Safety assessment of a concrete viaduct damaged by vehicle impact and an evaluation of the repair
PublikacjaDamage to lower parts of viaducts caused by impact from under-passing high vehicles is relatively frequent. One such incident, in which a viaduct was damaged by the impact from a truck with an improperly assembled hydraulic crane, is considered in this work. The analysis is based on a detailed object damage evaluation, 3D laser scanning, and numerical simulations. The aim of the study is to accurately model the vehicle impact into...
-
Programmed metalloporphyrins for self-assembly within light-harvesting stacks: 5,15-dicyano-10,20-bis(3,5-di-tert-butylphenyl)-porphyrinato zinc(II) and its push-pull 15-N,N-dialkylamino-5-cyano congeners obtained by a facile direct amination.
PublikacjaThe title dicyano compound was synthesized via cyanation and it self-assembles in nonpolar solvents giving red-shifted and broad absorption maxima just as the bacteriochlorophylls which are encountered in the light-harvesting organelles of early photosynthetic bacteria. In the crystal, stacks are formed through a hierarchic combination of π-stacking and a CNZn electrostatic interaction. Push−pull 15-N,N-dialkylamino-5-cyano congeners...
-
Modelling and analysis of medium frequency transformers for power converters
PublikacjaThe evolutions in power systems and electric vehicles, related to the economic opportunities and the environmental issues, bring the need of high power galvanically isolated DC-DC converter. The medium frequency transformer (MFT) is one of its key components, enabled by the increasing switching frequency of modern power semiconductors like silicon carbide transistors or diodes. The increased operating frequency offers small...
-
Pilicides effectively hinder chaperone-usher interactions in all Gram-negative bacteria
PublikacjaThe chaperone-usher pathway of adhesive structures biogenesis is highly conserved in all Gram-negative bacteria. Pili are polymers of thousands protein subunits that possess conserved immunoglobuline-like structure denoted by lack of the seventh G strand. The effect of this structural defect is a hydrophobic acceptor cleft. The folding of protein subunits is strictly dependent on the action of specific periplasmic chaperone protein...
-
Pose-Configurable Generic Tracking of Elongated Objects
PublikacjaElongated objects have various shapes and can shift, rotate, change scale, and be rigid or deform by flexing, articulating, and vibrating, with examples as varied as a glass bottle, a robotic arm, a surgical suture, a finger pair, a tram, and a guitar string. This generally makes tracking of poses of elongated objects very challenging. We describe a unified, configurable framework for tracking the pose of elongated objects, which...
-
Wpływ drążenia pionowego w silikatowych elementach murowych na nośność kotew wklejanych
PublikacjaThe article is showing results of measurements of the effectiveness of the assembly anchor of inmates glued in in sunk vertically lime-sandy blocks. Examinations were performed for cases of the assembly anchor in different fragments of blocks: in part fullwall, in an axis of symmetry and on the edge of the aperture vertical. An influence of the location of places of settling was examined anchor to the way of the forming of uniting...
-
Impact of AlphaFold on structure prediction of protein complexes: The CASP15‐CAPRI experiment
PublikacjaWe present the results for CAPRI Round 54, the 5th joint CASP-CAPRI protein assembly prediction challenge. The Round offered 37 targets, including 14 homodimers, 3 homo-trimers, 13 heterodimers including 3 antibody–antigen complexes, and 7 large assemblies. On average 70 CASP and CAPRI predictor groups, including more than 20 automatics servers, submitted models for each target. A total of 21 941 models submitted by these groups...
-
Design and Evaluation of the Compact and Autonomous Energy Subsystem of a Wave Energy Converter
PublikacjaThis paper presents the results of the design process focused on the development of the energy subsystem (ES) of a wave energy converter (WEC). The ES is an important electrical part that significantly affects the energy reliability and energy efficiency of the entire WEC device. The designed ES was intended for compact WECs powering IoT network devices working in the distributed grid. The developed ES is an electronic circuit...
-
Strain gauges monitoring of arch bridge over the Vistula river in Toruń during construction
PublikacjaIn 2013 one of the biggest Polish road bridges over the Vistula was built in Torun. Considering the use of original engineering solutions and innovative assembly it was decided on monitoring of strain gauges and assessment of building’s behaviour during its construction. The research was aimed at determining the degree of strain and the assessment of proper work of main arch girders during assembly phases. This work presents the...
-
Self-Association of Amphotericin B: Spontaneous Formation of Molecular Structures Responsible for the Toxic Side Effects of the Antibiotic
PublikacjaAmphotericin B (AmB) is a lifesaving antibiotic used to treat deep-seated mycotic infections. Both the pharmaceutical activity and highly toxic side effects of the drug rely on its interaction with biomembranes, which is governed by the molecular organization of AmB. In the present work we present detailed analysis of self-assembly of AmB molecules in different environments, interesting from the physiological standpoint, based...
-
Interplay of hydrogen bonding and aryl-perfluoroaryl interactions in construction of supramolecular aggregates
PublikacjaThe stacking between aryl and perfluoroaryl units is an important class of the aromatic – aromatic interactions that has attracted rapidly growing interest in recent years. Continuing interest of our group in this subject it had been prepared three new complexes of pentafluorobenzoic acid with benzyl alcohol, 4-methylbenzyl alcohol and 4-tert-butylbenzyl alcohol and in the next step investigated their self-assembly modes by...
-
Aggregation of nonionic surfactants in imidazolium ionic liquids
PublikacjaMicellar aggregation of surfactants in aqueous solutions has been described in terms of the balance between dispersive interactions of the hydrocarbon part of the amphiphilic molecule, and the hydration and electrostatic repulsive effects of hydrophilic head group. Changing the interactions by replacing water with another polar solvent, such as amides or glycols, has been studied to a smaller extent (Singh, Saleem et al. 1980;...
-
DESIGN AND THEORETICAL ANALYSIS OF A PROTOTYPE TILTING-PAD RADIAL BEARING WITH ADJUSTABLE CLEARANCE
PublikacjaThe article introduces a design and analysis results of a prototype ORC (organic Rankine cycle) turbo generator rotor assembly of 300kW power, supported by tilting-pad bearings of original design. The calculations were performed for a prototype turbo generator rotor. The shaft of this machine is supported with two radial bearings, lubricated with an unusual lubricant – a low-boiling-point agent. The main objective of the presented...
-
Highly linear self-assembled porphyrin wires
PublikacjaAn efficient noncovalent assembly process involving high geometrical control was applied to a linear bis(imidazolyl zinc porphyrin) 7Zn, bearing C18 substitutents, to generate linear multiporphyrin wires. The association process is based on imidazole recognition within the cavity of the phenanthroline-strapped zinc porphyrin. In chlorinated solvents, discrete soluble oligomers were obtained after (7Zn)n was end-capped with a terminal...
-
Application of the Mathar method to identify internal stress variation in steel as a welding process result
PublikacjaThe paper deals with the method to identify internal stresses in two-dimensional steel members. Steel members were investigated in the delivery stage and after assembly, by means of electric-arc welding. In order to perform the member assessment two methods to identify the stress variation were applied. The first is a non-destructive measurement method employing local external magnetic field and to detecting the induced voltage,...
-
Results from tests on bolted connection components for evaluation of friction coefficient in various contact conditions
PublikacjaThe main purpose of the work was the analysis and evaluation of the self-locking quality of a bolted joint covered with Xylan 1070 coating, with comparison to the classic bolts lubricated with Molykote compound during assembly. The second part of the work was the verification of the compliance of the bolts and nuts used in the installation with the ASME B1.1 norm.
-
Segmentation-Based BI-RADS ensemble classification of breast tumours in ultrasound images
PublikacjaBackground: The development of computer-aided diagnosis systems in breast cancer imaging is exponential. Since 2016, 81 papers have described the automated segmentation of breast lesions in ultrasound images using arti- ficial intelligence. However, only two papers have dealt with complex BI-RADS classifications. Purpose: This study addresses the automatic classification of breast lesions into binary classes (benign vs. ma- lignant)...
-
THE EFFECT OF ALTERNATIVE CUTTER PATHS ON FLATNESS DEVIATIONS IN THE FACE MILLING OF ALUMINUM PLATE PARTS
PublikacjaIn this paper the relationships between the alternative machining paths and flatness deviations of the aluminum plate part, were presented. The flatness tolerance of the main surface of the plate part has crucial meaning due to the assembly requirement of piezoelectric elements on the radiator. The aluminum bodies under investigation are the base part of the radiators with crimped feathers for the train industry. The surface of...
-
Review of non- welded piping technologies on offshore equipment projects
PublikacjaThe aim of this article are considerations on welded and non-welded tube connection technologies, with advantages and disadvantages of both. After choosing non-welded solutions as the assembly method of choice, the thesis progresses to describing the most widely-used tube connection technologies (JIC, Ermeto, retain ring flanges, flared tube flanges and other, minor, solutions) and their properties.
-
Design of Inner Gate for CRIST Shipyard Dry Dock
PublikacjaThe paper deals with a removable steel inner gate which was designed to separate two parts of a dry dock of about 70 m in width and 380 m in length. The gate allows for independent assembly of ship structures in two separated parts of the dock. The fore part of the dock can be flooded while the after part is dry. Tthe gate was designed by IDEK Company Ltd in 2011 and it was soon constructed and used by CRIST Shipyard in Gdynia.
-
Several notes on technical modernization of a historical building
PublikacjaThis paper describes methods and means used during the renovation process of several elements of a building – the assembly hall, inner courtyards and attics of the main building at Gdansk University of Technology, both in design and construction domains. A tissue of a historic building required special approach to these tasks, with special emphasis on good recognition of problems, careful planning and consistent implementing of...
-
Communication and Load Balancing Optimization for Finite Element Electromagnetic Simulations Using Multi-GPU Workstation
PublikacjaThis paper considers a method for accelerating finite-element simulations of electromagnetic problems on a workstation using graphics processing units (GPUs). The focus is on finite-element formulations using higher order elements and tetrahedral meshes that lead to sparse matrices too large to be dealt with on a typical workstation using direct methods. We discuss the problem of rapid matrix generation and assembly, as well as...
-
Damage of a post-tensioned concrete bridge – Unwanted cracks of the girders
PublikacjaThe cracking of a post-tensioned T-beam superstructure, which was built using the incremental launching method, is analyzed in the paper. The problem is studied in detail, as specific damage was observed in the form of longitudinal cracks, especially in the mid-height zone of the girder at the interface of two assembly sections. The paper is a case study. A detailed inspection is done and non-destructive testing results of the...
-
Reduction of Derivative pipeline effort in water turbine
PublikacjaThe paper presents an approach to evaluate and reduce the effort of the derivative pipeline in a water turbine of a hydrostatic power station in its vulnerable spots. Potential places of the biggest effort of the structure, as well as the coefficient of displacement and safety factor related to them were identified using FEM numerical method. Pipeline reinforcement was designed and made based on FEM analysis. Original technology...
-
Checkpoints that regulate balanced biosynthesis of lipopolysaccharide and its essentiality in Escherichia coli
PublikacjaThe outer membrane (OM) of Gram-negative bacteria, such as Escherichia coli, is essential for their viability. Lipopolysaccharide (LPS) constitutes the major component of OM, providing the permeability barrier, and a tight balance exists between LPS and phospholipids amounts as both of these essential components use a common metabolic precursor. Hence, checkpoints are in place, right from the regulation of the first committed step...
-
Polarization interferometer using a Liquid Crystalline Polymer waveplate for wavelength measurement
PublikacjaA two-beam polarization interferometer for measuring wavelength changes of a tunable semiconductor laser was designed, built and tested. This interferometer uses a λ/8 waveplate made from Liquid Crystalline Polymer in order to generate two output signals in quadrature. The λ/8 waveplate can be manufactured either on a beamsplitter face or on the mirror surface, reducing the cost and complexity of the optomechnical assembly. Experiment...
-
Finite element matrix generation on a GPU
PublikacjaThis paper presents an efficient technique for fast generation of sparse systems of linear equations arising in computational electromagnetics in a finite element method using higher order elements. The proposed approach employs a graphics processing unit (GPU) for both numerical integration and matrix assembly. The performance results obtained on a test platform consisting of a Fermi GPU (1x Tesla C2075) and a CPU (2x twelve-core...
-
On a design of a torque sensor for the iCub humanoid robot
PublikacjaThe paper presents the evaluation process of a first version of the one axis torque sensor designed for the iCub humanoid robot. Newly designed strain gauges equipped sensor was found to show a significant readouts hysteresis, therefore several tests were run to define the reason of the hysteresis. Some of the design issues met while testing the new sensor are discussed including the screws connection and relative rigidity of the...
-
Prediction of protein assemblies, the next frontier: The CASP14‐CAPRI experiment
PublikacjaWe present the results for CAPRI Round 50, the 4th joint CASP-CAPRI protein assembly prediction challenge. The Round comprised a total of 12 targets, including 6 dimers, 3 trimers, and 3 higher-order oligomers. Four of these were easy targets, for which good structural templates were available either for the full assembly, or for the main interfaces (of the higher-order oligomers). Eight were difficult targets for which only distantly...
-
Safety of erection and repair of steel tanks with geometric imperfections using heavylift jack-up system
PublikacjaSafety analysis is performed of cylindrical vertical steel tanks during erection using heavylift jack up system. During an assembly or repair process a set of hydraulic supports is used. It allows to use the in-place lifting of heavy steel constructions on the required height. Wind can strongly influence stability of the lifted tank. Any geometric imperfections can reduce the critical or limit load. In the work failures of the...
-
Application of Barkhausen effect in the impact assessment of welding to internal stress distribution in steel
PublikacjaThe paper presents identification method of internal stresses in plane steel elements in the chase of deliverance and welding assembly. The assessment was made by means of a non-destructive experimental method based on measurements incorporating local external magnetic field and the measurement of induced voltage, including Barkhausen noise. This method allows a degradation assessment due to internal and external actions, causing...
-
Application of Barkhausen effect in the impact assessment of welding to internal stress distribution in steel
PublikacjaThe paper presents identification method of internal stresses in plane steel elements in the chase of deliverance and welding assembly. The assessment was made by means of a non-destructive experimental method based on measurements incorporating local external magnetic field and the measurement of induced voltage, including Barkhausen noise. This method allows a degradation assessment due to internal and external actions, causing...
-
Selected aspects of system design theory.
PublikacjaPrzedstawiono wybrane zagadnienia z teorii projektowania systemów. Szczgólną uwagę zwrócono na problemy występujące w systemach o dużej złożoności, które charakteryzują się skomplikowaną funkcją globalną, jak również dużą ilością elementów należących do takich systemów. Omówiono także niektóre cechy elementów wynikające z różnych procesów wytwarzania oraz ich wpływ na funkcję, strukturę i eksploatację systemu, powstałego ze skojarzenia...
-
The complexity of bicriteria tree-depth
PublikacjaThe tree-depth problem can be seen as finding an elimination tree of minimum height for a given input graph G. We introduce a bicriteria generalization in which additionally the width of the elimination tree needs to be bounded by some input integer b. We are interested in the case when G is the line graph of a tree, proving that the problem is NP-hard and obtaining a polynomial-time additive 2b-approximation algorithm. This particular...
-
An innovative method of measuring the extension of the piston rod in hydraulic cylinders, especially large ones used in the shipbuilding and offshore industry
PublikacjaThe article presents the results of selected works related to the wider subject of research conducted at the Faculty of Mechanical Engineering and Shipbuilding at the Gdańsk University of Technology, regarding designing various on board devices with hydraulic drive for ships and other offshore facilities. One of the commonly used these mechanisms are hydraulic actuators with the measurement of the piston rod extension. The issue...
-
APPLICATION OF INFRARED THERMOGRAPHY TO NON-CONTACT TESTING OF AD/DC POWER SUPPLY
PublikacjaTesting of AC/DC power supplies using the thermography was carried out in order to assess their assembly and operation correctness before launching them on the market. The investigation was carried out for 17 AC/DC power supplies which passed the standard tests (measurements of their basic parameters and characteristics). The investigation consisted of two steps. In the first step the dispersion of temperature on power supply boards...
-
π-Conjugated Donor-acceptor Polyelectrolytes: Toward Artificial Photosynthesis
PublikacjaGreat advances have been made in the development of conjugated polyelectrolytes (CPEs), which provide tunable properties including water solubility and processability, main-chain exciton and charge transport, variable energy light absorption and fluorescence, non-covalent interactions, and formation of tertiary structures via self-assembly.[1] These characteristics allow CPEs to be considered for use in various optoelectronic applications,...
-
Accurate and continuous adhesive fracture energy determination using an instrumented wedge test
PublikacjaThe wedge test and the related double cantilever beam test are practical methods of assessing structural adhesive fracture energy. In the former, and to a lesser extent the latter, a recognised problem is the difficulty of following the length of the growing crack, required to calculate fracture energy with any accuracy. We present a novel method of measurement of crack length that has the advantages of being accurate and allowing...
-
ortho-Fluorobenzanilides and ortho-fluorothiobenzanilides: Molecular conformations and crystal packing
PublikacjaSeries of 2-fluoro and 2,6-difluorobenzanilides and their thiobenzanilide analogs have been synthesized to investigate the influence of the fluorine atom on their crystal structures and self-assembly in the crystal lattice. The X-ray analysis of the single crystal revealed that the synthesized molecules adopt a geometry being deflected from planarity. The deflection was investigated by analysis of dihedral angles between mean planes...
-
A CONCEPT DESIGN OF DIESEL – HYDRAULIC PROPULSION SYSTEM FOR PASSENGER SHIP INTENDED FOR INLAND SHALLOW WATER NAVIGATION
PublikacjaThis paper presents an analysis of environmental and technical conditions necessary for working out a possibly most favourable propulsion system for a two – segment passenger ship intended for navigation between Berlin and Kaliningrad. There are presented various types of propulsion systems for small ships as well as analyzed their possible applications and consequences. In this work there were taken into account system’s reliability,...
-
Intermolecular Hydrogen Bonding Directed by Aryl–Perfluoroaryl π–π Stacking Interactions
PublikacjaThe crystal structures of five compounds capable of forming self-complementary hydrogen bonds but crystallizing as catemers or creating more complex crystal structures were compared with their complexes prepared by cocrystallization with perfluoroaryl compounds. The results of X-ray diffraction revealed that in all the cases the π–π stacking interactions caused reorganization of hydrogen bonds and induced creation of the expected...
-
Morphology control via dual solvent crystallization for high-mobility functionalized pentacene-blend thin film transistors
PublikacjaWe present an approach to improving the performance of solution processed organic semiconductor transistors based on a dual solvent system. We here apply this to a blend containing the π-conjugated small molecule 6,13 bis(triisopropylsilylethynyl) pentacene (TIPS-pentacene) and polystyrene, which acts as an inert binder. Using a semiconductor-binder solution of two solvents, where the main solvent is a better solvent of the small...
-
Chemical treatment of crystalline silicon solar cells as a main stage of pv modules recycling = Obróbka chemiczna krzemowych ogniw słonecznych jako najważniejszy etap w recyklingu modułów fotowoltaicznych
PublikacjaIn recent years, photovoltaic systems have gained worldwide recognition and popularity as a environmentally friendly way of solving energetic problems. However, a problem of utilizing worn out photovoltaic systems, amount of which will rapidly increase in the future, is yet to be solved. Establishing a technology of recycling and reusing obsolete photovoltaic panels is a necessity.Photovoltaic modules in crystalline silicon solar...
-
COMPARATIVE ANALYSES OF INTERNATIONALIZATION OF KAZAKHSTAN ENTERPRISES
PublikacjaThis paper presents the instruments of internationalization of enterprises operating within the Eurasian Economic Union. Research contains answers of 108 enterprises exporters located in the Republic of Kazakhstan. The purpose of the paper is to show the main forms of the internationalization of enterprises in Kazakhstan. The paper also presents the following instruments of enterprises’ internationalization including: indirect...
-
Torque Transmitted by Multi-plate Wet Clutches in Relation to Number of Friction Plates and Their Dimensions
PublikacjaIn the paper results of experimental tests on multi-plate wet clutch torque capacity for various diameters and numbers of friction plates are presented. Construction of an apparatus for laboratory tests of wet clutch engagement, drag torque and maximum torque is shown. Methodology of maximum torque capacity experiment and hydraulic circuit diagram, which supplies a motor and an actuator for the experiment are described. Analytically...
-
Ln2(SeO3)2(SO4)(H2O)2 (Ln=Sm, Dy, Yb): A Mixed‐Ligand Pathway to New Lanthanide(III) Multifunctional Materials Featuring Nonlinear Optical and Magnetic Anisotropy Properties
PublikacjaBottom-up assembly of optically nonlinear and magnetically anisotropic lanthanide materials involving precisely placed spin carriers and optimized metal-ligand coordination offers a potential route to developing electronic architectures for coherent radiation generation and spin-based technologies, but the chemical design historically has been extremely hard to achieve. To address this, we developed a worthwhile avenue for creating...