Wyszukiwarka
Filtry
wszystkich: 852
wybranych: 746
Wyniki wyszukiwania dla: airborne wear particles
-
Effective density of airborne wear particles from car brake materials
PublikacjaPeople living in urban environments are subject to high health risks due to various anthropogenic sources of airborne particulate matter, including wear of transport vehicle brakes. Studies of airborne particles often require an estimate of the effective particle density, a property that allows correct matching of mass and size characteristics measured by different aerosol instruments. In this study we investigated the effective...
-
A Study on Emission of Airborne Wear Particles from Car Brake Friction Pairs
PublikacjaThe emission of airborne wear particles from friction material / cast iron pairs used in car brakes was investigated, paying special attention to the influence of temperature. Five low-metallic materials and one non-asbestos organic material were tested using a pin-on-disc machine. The machine was placed in a sealed chamber to allow airborne particle collection. The concentration and size distribution of 0.0056 to 10 μm particles...
-
Emission and properties of airborne wear particles from train brake friction materials based on novolac phenolic resins and butadiene rubbers
PublikacjaThe emission of airborne particulate matter from a train brake depends on the formulation of its friction material. This study investigates the emission and properties of wear particles from train brake friction materials based on straight or resorcinol-modified novolac phenolic resin and nitrile or styrene butadiene rubber used as binding ingredients. The wear particles are generated by a pin-on-disc tribomachine inside an aerodynamic...
-
Correlations between the wear of car brake friction materials and airborne wear particle emissions
PublikacjaAirborne wear particles emitted from transport vehicle brakes are one of the main sources of toxic metals in inhalable particulate matter. Prediction of wear particle emissions may become more accurate if the relationship between the wear and particle emission characteristics is known. An experimental study was performed to investigate proportional correlations between the mass wear, 0.01–0.42 μm particle emission measured by a NanoScan...
-
Emission of 1.3–10 nm airborne particles from brake materials
PublikacjaOperation of transport vehicle brakes makes a significant contribution to airborne particulate matter in urban areas, which is subject of numerous studies due to the environmental concerns. We investigated the presence and number fractions of 1.3–10 nm airborne particles emitted from a low-metallic car brake material (LM), a non-asbestos organic car brake material (NAO) and a train brake cast iron against a cast iron. Particles...
-
Quantification of ultrafine airborne particulate matter generated by the wear of car brake materials
PublikacjaThe wear of car brakes is one of the main sources of airborne particulate matter in urban environments. Ultrafine wear particles are of special environmental interest since they can easily penetrate the human body through inhalation and cause various diseases. In the present study, the contribution of ultrafine particles to airborne particulate matter emitted from car brake materials was investigated under different friction conditions....
-
Analysis of airborne metal containing particles with EDX/EDS detectorsin electron microscopes
PublikacjaIn years 2006-2010 particulate matter analysis was undertaken for dust samples collected from Gdansk and London area in orderto compare their morphology and composition. Part of those studies was devoted to analysis of particulate matter (PM) bearingmetals. Characterization of the morphology and size of the particles collected onto the filters was performed using a scanning electronmicroscope (SEM) and transmission electron microscope...
-
A pin-on-disc study of airborne wear particle emissions from studded tyre on concrete road contacts
PublikacjaStudded tyres wear surfaces of winter roads, generating inhalable airborne particles. In this study, four concrete road materials and two stud geometries were investigated in terms of wear, road material hardness and airborne particle concentration. The sliding contact between studded tyres and road materials was studied using a pin-on-disc machine in a clean chamber. The results show that the normal load and the stud size have...
-
Airborne wear particle emission from train brake friction materials with different contents of steel and copper fibres
PublikacjaThis study investigated the influence of the amount of steel and copper fibres in a train brake friction material on the tribological performance, emission intensity and characteristics of airborne wear particles. The particles were generated on a pin-on-disc tribometer under controlled friction and environmental conditions. It was found that the steel fibre results in a more intensive emission of 0.3–10 μm particles compared to...
-
Porosity and shape of airborne wear microparticles generated by sliding contact between a low-metallic friction material and a cast iron
PublikacjaThe wear of brakes in transport vehicles is one of the main anthropogenic sources of airborne particulate matter in urban environments. The present study deals with the characterisation of airborne wear microparticles from a low-metallic friction material / cast iron pair used in car brakes. Particles were generated by a pin-on-disc machine in a sealed chamber at sliding velocity of 1.3 m/s and contact pressure of 1.5 MPa. They...
-
A concept for reducing PM 10 emissions for car brakes by 50%
PublikacjaWith regard to airborne particles with an aerodynamic diameter of less than 10 μm (PM10), in countries in the European Union, the mass of brake emissions equals approximately 8–27% of the total traffic-related emissions. Using a research methodology combining tests at different scale levels with contact mechanics simulations and PM10 chemical characterization, the REBRAKE EU-financed project had the following aims: i) to demonstrate...
-
Influence of permanent magnetic field on wear performance of dry sliding contacts
PublikacjaResults of experimental studies concerning the influence of permanent magnetic field on wear of dry sliding contact are presented.It was found that magnetic field of horizontal orientation is causing temporary reduction of material's hardness. It also facilitates and accelerates removal process of wear particles from the contact zone.Formation of bulges, consisting of accumulated and compacted anti-ferromagnetic material produced...
-
Sliding bearings with sintered bronze bush lubricated by contaminated water with solid particles – Theoretical and experimental studies
PublikacjaSliding journal bearings lubricated with water coming directly from the environment are a solution used in shipbuilding, pumps and hydropower. However, the working fluid or surrounding water cannot always be filtered because of design limitations, which often causes the problem of premature wear of these sensitive bearings. The research conducted made it possible to assess the wear of sliding bearings lubricated with water containing...
-
Optimization of Single-Sided Lapping Kinematics Based on Statistical Analysis of Abrasive Particles Trajectories
PublikacjaThe chapter presents the influence of selected kinematic parameters on the geometrical results of the single-sided lapping process. The optimization of these parameters is aimed at improving the quality and flatness of the machined surfaces. The uniformity of tool wear was assumed as main optimization criterion. Lapping plate wear model was created and in detail was analyzed. A Matlab program was designed to simulate the abrasive...
-
Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites
PublikacjaHybrid aluminium metal matrix composites have the potential to replace single reinforced aluminium metal matrix composites due to improved properties. Moreover, tribological performance is critical for these composites, as they have extensive application areas, such as the automotive, aerospace, marine and defence industries. The present work aims to establish the tribological characteristics of Al7068/Si3N4/BN hybrid metal matrix...
-
Modeling of lapping plate wear and conditioning in single-sided lapping
PublikacjaIn order to achieve higher quality on worked surfaces with lower roughness, very high accuracy of shape and dimensions it is crucial to improve conventional finishing technologies and to develop new working principles. Single-sided lapping is one of the most effective planarization technologies and it is determined by a number of factors and boundary conditions. The most significant influence over a dimensional and profile accuracy,...
-
Real-time monitoring of volatiles and particles emitted from thermoplastic filaments during 3D printing
PublikacjaThe proliferation of consumer-grade three-dimensional (3D) printers using fused deposition, also known as fused filament fabrication, has given rise to concerns over the exposure of users to potentially harmful substances. Thermoplastic filaments made of different polymers are extruded through a heated printer nozzle and deposited layer by layer on a build platform to form the printed object. This process leads to the emission...
-
Wear of electroplated diamond tools in lap-grinding of Al2O3 ceramic materials
PublikacjaCurrent development of modern products, together with ever-increasing demands for their operation and usage, necessitate the search for new processing methods. Abrasive machining is widely used in many industrial areas, especially for processing difficult-to-machine materials such as advanced ceramics. Grinding with lapping kinematics, also called lap-grinding, is still one of the innovative methods of abrasive processing being...
-
Tribological Properties of Ni-P/Si3N4 Nanocomposite Layers Deposited by Chemical Reduction Method on Aluminum Alloy AW-7075
PublikacjaThe article presents the results of tribological tests of Ni-P/Si3N4 nanocomposite and Ni-P nickel layers deposited on the AW-7075 aluminum alloy by chemical reduction method, and the AW-7075 alloy without coating. Nanocomposite layers were produced using Si3N4 siliconnitride in the form of a polydisperse powder whose particle sizes ranged from 20 to 25 nm. The influence of the content of the dispersion phase layer material on...
-
Nickel-nanodiamond coatings electrodeposited from tartrate electrolyte at ambient temperature
PublikacjaIn this study, nanocrystalline Ni and Ni-diamond coatings were obtained by electrodeposition from tartrate electrolyte at ambient temperature aiming at improving corrosion and wear properties of the material. The created surfaces were investigated with regard to microhardness, adhesion, wear- and corrosion-resistance. The various methods such as atomic force microscopy, scanning electron microscopy, electrochemical impedance spectroscopy...
-
The Effect of Cryogenic Treatment on Microstructure and Mechanical Response of AISI D3 Tool Steel Punches
PublikacjaRecently, deep cryogenic treatment is performed to improve the mechanical responses (wear, hardness, fatigue, and thermal conductivity) of various steel components. Researchers have tried to evaluate the eco-friendly and nontoxic process to optimize the parameters. Cold-shearing punches used to manufacture various holes that undergo severe impact loading and wear in the metal forming process. This study concerns the effect of soaking...
-
Mitigation effect of face shield to reduce SARS-CoV-2 airborne transmission risk: Preliminary simulations based on computed tomography
PublikacjaWe aimed to develop a model to quantitatively assess the potential effectiveness of face shield (visor) in reducing airborne transmission risk of the novel coronavirus SARS-CoV-2 during the current COVID-19 pandemic using the computational fluid dynamics (CFD) method. The studies with and without face shield in both an infected and healthy person have been considered in indoor environment simulation. In addition to the influence...
-
Mitigation effect of face shield to reduce SARS-CoV-2 airborne transmission risk: Preliminary simulations based on computed tomography
PublikacjaWe aimed to develop a model to quantitatively assess the potential effectiveness of face shield (visor) in reducing airborne transmission risk of the novel coronavirus SARS-CoV-2 during the current COVID-19 pandemic using the computational fluid dynamics (CFD) method. The studies with and without face shield in both an infected and healthy person have been considered in indoor environment simulation. In addition to the influence...
-
Non-conventional approach in single-sided lapping process: kinematic analysis and parameters optimization
PublikacjaThe lapping process is strongly affected by a number of input parameters. One of the fundamental mechanical processes in lapping is the abrasive effect of particles. In order to examine the influence of the kinematic parameters on the lapping uniformity of unconventional single-sided machine, numerical simulations of particles sliding trajectories are performed. Changing the kinematic parameters, e.g., rotational velocities or...
-
The use of Preston equation to determine material removal during lap-grinding with electroplated CBN tools
PublikacjaGrinding executed in a lapping configuration is an alternative finishing process benefiting from both grinding and free-abrasive machining, while minimizing the heat effect impact. Electroplated tools can be effectively used in different abrasive processes, including high-speed grinding, however, the assessment of machining performance over time is a key factor in their correct use to achieve satisfactory technological results....
-
Degradation of electrical performance of a crystalline photovoltaic module due to dust deposition in northern Poland
PublikacjaThe reduction in power output caused by the accumulation of dust on the photovoltaic module surface is an important problem and should receive much more attention in the literature. This study was an evaluation of the performance degradation of crystalline photovoltaic modules due to natural and simulated dust deposition. Dust is created from powdered grains of sand and particles of different bodies. Dust originates from different...
-
Polybrominated diphenyl ether (PBDE) concentrations in dust from various indoor environments in Gdańsk, Poland: Prediction of concentrations in indoor air and assessment of exposure of adults
PublikacjaMonitoring of polybrominated diphenyl ethers (PBDEs) in indoor environments involves the determination of their concentrations in air, airborne particles, and settled dust. Each of these is a source of human exposure to PBDEs. In this study, we attempted to model PBDEs concentrations in various typical indoor environments on the basis of real PBDEs measurements in dust collected from them. The analytical procedure for determining...
-
Diatomaceous earth as a drug-loaded carrier in a glass-ionomer cement
PublikacjaThe effect of a natural filler (diatomaceous earth [DE], a promising drug-delivery agent) and its content was investigated on the performance of a model glass-ionomer cement (GIC). Three sample series, differing in DE content (0, 2.5 and 5 wt%), were prepared using a commercial GIC as a matrix (3M Ketac Molar Easymix). The resultant surface microhardness and roughness, wear performance, and compressive strength of the samples were...
-
Mechanical Behavior of Bi-Layer and Dispersion Coatings Composed of Several Nanostructures on Ti13Nb13Zr Alloy
PublikacjaTitanium implants are commonly used because of several advantages, but their surface modification is necessary to enhance bioactivity. Recently, their surface coatings were developed to induce local antibacterial properties. The aim of this research was to investigate and compare me-chanical properties of three coatings: multi-wall carbon nanotubes (MWCNTs), bi-layer composed of an inner MWCNTs layer and an outer TiO2 layer, and...
-
Determination of polybrominated diphenyl ethers in house dust using standard addition method and gas chromatography with electron capture and mass spectrometric detection
PublikacjaMonitoring of the environmental fate of polybrominated diphenyl ethers (PBDEs) involves determination of their concentration in air, airborne particles and settled dust. This requires the implementation of appropriate analytical tools like measuring instruments, reference materials and analytical procedures. In this study an analytical procedure was developed for determining PBDEs in samples with a complex matrix composition. The...
-
Laser Welding of UNS S33207 Hyper-Duplex Stainless Steel to 6061 Aluminum Alloy Using High Entropy Alloy as a Filler Material
PublikacjaThe high entropy alloy (HEA) filler used during the fabrication method determines the reliability of HEAs for steel-aluminum dissimilar alloy configuration. HEAs have a direct impact on the formation of intermetallic compounds (IMC) formed by the interaction of iron (Fe) and aluminum (Al), and influence the size of the joint’s interaction zone. A novel welding process for Fe-Al alloy joints was developed to prevent the development...
-
The wave character of commutator wear in electrical machines
PublikacjaW pracy przedstawiono wyniki badań doświadczalnych zużycia elementów ze styku ślizgowego silnika komutatorowego prądu przemiennego małej mocy. Zakres badań obejmował okresowe pomiary profilu powierzchni ślizgowej komutatora w przekroju poprzecznym oraz profilu powierzchni wycinków komutatora w przekroju podłużnym względem osi wirowania. Ponadto zmierzono okresowe wielkości zużycia powierzchni ślizgowej komutatora oraz szczotek...
-
Experimental analysis of wear resistance of compacts of fine-dispersed iron powder and tungsten monocarbide nanopowder produced by impulse pressing
PublikacjaThe paper presents the results of studying the structure and wear resistance of compacts produced from fine dispersed reduced iron powder (average particle size 3–mu m) with the addition of tungsten carbide (WC) nanopowder with the average particle size of 25–30 nm. The mass fraction of tungsten carbide (wolfram carbide) in the powder composition was 5% and 10% of the total mass. Impulse pressing was conducted using the modified...
-
ASSESSMENT OF WEAR OF THE BANDSAW TEETH IN INDUSTRIAL CONDITIONS
PublikacjaA methodology for measuring bandsaw tooth wear is presented in this paper. This type of measurement is proposed as an alternative way of determining tooth wear in industrial conditions. The method is based on determining the KE value, i.e., the distance of the radius of the rounded cutting edge of the tooth and the intersection of the surface of the back and the surface of the face of the cutting wedge of the bandsaw tooth....
-
Pseudo-superparamagnetic behaviour of bariumhexaferrite particles
PublikacjaThe effect of hexadecyltrimethylammonium bromide (CTAB) addition on the crystal structure, morphology,and magnetic properties of co-precipitated hexagonal barium ferrite was investigated. For afixed amount ofsurfactant, different Fe3+concentrations and Fe3+/Ba2+ratios were used to optimize the formation ofsingle-phase barium ferrite particles. The results indicated that the obtained ferrite particles exhibitedcoercivity changes...
-
Types of wear and tear of biomaterials used in orthopaedic surgery
PublikacjaPurpose of this paper is presentation of observations on different kinds of wear and tear of biomaterials used in contemporary orthopaedic surgery. Types of prosthesis damage, encountered in medical practice, and their causes have been described. Results of many clinical studies were analysed to review prosthesis damage from the stage of implanting (such as intrusion of a foreign object between its components) to their natural...
-
Airborne and mobile laser scanning in measurements of sea cliffs on the southern Baltic
PublikacjaMeasurements of sea cliffs performed using periodic surveying based on laser scanning is currently one of the fastest and most accurate solutions. Supported with the technology of satellite measurements using GNSS (Global Navigation Satellite System) positioning and photographic measurements with the use of aerial vehicle, they enable an effective monitoring of the sea cliffs affected by the erosion. In case of the coast of southern...
-
WEAR OF Si OR B DOPED AMORPHOUS CARBON COATINGS
PublikacjaThe paper describes a complex wear research on DLC (amorphous carbon) moped with boron (B) and silicone (Si). The tests were carried out in two different sliping systems: flat–on–flat (ring contact, unidirectional sliding) and ball–on–flat (reciprocating sliding). Water and medical saline solutions were used as lubricants. A comparative analysis of the results revealed differences in the initiation and progress of wear and the...
-
Tool Wear Prediction in Single-Sided Lapping Process
PublikacjaSingle-sided lapping is one of the most effective planarization technologies. The process has relatively complex kinematics and it is determined by a number of inputs parameters. It has been noted that prediction of the tool wear during the process is critical for product quality control. To determine the profile wear of the lapping plate, a computer model which simulates abrasive grains trajectories was developed in MATLAB. Moreover,...
-
Automatic classification and mapping of the seabed using airborne LiDAR bathymetry
PublikacjaShallow coastal areas are among the most inhabited areas and are valuable for biodiversity, recreation and the economy. Due to climate change and sea level rise, sustainable management of coastal areas involves extensive exploration, monitoring, and protection. Current high-resolution remote sensing methods for monitoring these areas include bathymetric LiDAR. Therefore, this study presents a novel methodological approach to assess...
-
APPLYING RANSAC ALGORITHM FOR FITTING SCANNING STRIPS FROM AIRBORNE LASER SCANNING
PublikacjaDuring the development of the data acquired by airborne laser scanning the important issue is the fitting and georeferencing of ALS point clouds by means of the tie surfaces and the reference planes. The process of scanning strips adjustment is based on mutual integration of point clouds (scanning strips) and their adaptation to the reference planes.In simultaneous adjustment all strips are combined into one geometrically coherent...
-
Wear measurements of self lubricating bearing materials in small oscillatory movement
PublikacjaRosnące wymagania ekologiczne powodują wzrost tendencji wymiany klasycznych materiałów łożyskowych, wymagających dodatkowego czynnika smarnego, na materiały nie wymagające smarowania. Zamianie takiej może towarzyszyć obniżenie trwałości zmodernizowanego łożyska. Ten niekorzystny efekt nierzadko obserwuje się w węzłach łożyskowych kierownic turbin wodnych. Autorzy podjęli próbę wyjaśnienia zjawisk występujących w tego typu łożyskach....
-
Wear measurements of self-lubricating bearing materials in small oscillatory movement
Publikacja -
Influence of magnetic field on wear in high frequency reciprocatingsliding contacts
PublikacjaResults of experimental studies concerning the influence of permanent magnetic field on wear of dry sliding contact operating at short stroke and high frequency are presented. It was found that horizontal magnetic field with different orientations relative to the sliding direction is affecting performance of the contact. The increase in frequency of sliding reduces accumulated mass loss and lowers the surface roughness of the wear...
-
Research on the wear evenness of the tool in flat lapping
PublikacjaIn this paper, the dimensionless distribution of the material removal stock and the trajectories of abrasive grains cutting in single-sided lapping process are presented. They were numerically simulated based on the tribological model and kinematics equations. It can be observed that the trajectories geometry of single abrasive as well the velocities have a great influence on the final geometrical deviation. During machining, the...
-
A COMPARISON OF WEAR PROPERTIES OF WATER LUBRICATED NBR AND PTFE SLIDING BEARINGS
PublikacjaThe excessive wear of a journal shaft can be caused by many factors, for example, working conditions (e.g., temperaturę, slip speed, the type of lubricant), pressure, the type of material used on the bearings and shafts and their roughness, as well as contamination remaining in the system. This paper presents the roughness profiles co-operating with a rubber (NBR) and polytetrafluoroethylene (PTFE) bushes. The conditions of cooperation...
-
High performance filtering for big datasets from Airborne Laser Scanning with CUDA technology
PublikacjaThere are many studies on the problems of processing big datasets provided by Airborne Laser Scanning (ALS). The processing of point clouds is often executed in stages or on the fragments of the measurement set. Therefore, solutions that enable the processing of the entire cloud at the same time in a simple, fast, efficient way are the subject of many researches. In this paper, authors propose to use General-Purpose computation...
-
Haemocompatibility Of Non-Functionalized And Plasmachemical Functionalized Detonation Nanodiamond Particles
PublikacjaThe purpose of this paper is to present the innovative design of microwave plasma system for modification of detonation nanodiamond particles (DNP) using a special rotating drum placed inside the reactor. Nanodiamond particles manufactured by detonation method reveal the biological activity depending on surface functionalization. Plasmachemical modification of detonation nanodiamond particles gives the possibility of controlling...
-
Mechanical, thermo-mechanical properties of epoxy/glass composites with submicron particles
PublikacjaIn this research the influence of submicron zinc oxide and silicon dioxide particles on mechanical, thermo-mechanical properties of epoxy matrix composites reinforced with glass fibres was investigated. Composites were fabricated using hand lay-up method. Materials contained 39-41 wt.% of glass fibres. The bending tests, dynamic mechanical analysis and tribological tests were performed on each group of composites and also for...
-
An algorithm to generate high dense packing of particles with various shapes
PublikacjaDiscrete Element Method (DEM) is one of available numerical methods to compute movement of particles in large scale simulations. The method has been frequently applied to simulate the cases of grain or bulk material as the major research issue. The paper describes a new method of generating high dense packing with mixed material of two different shape used in DEM simulation. The initial packing is an important parameter to control,...