wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: tailor-made polysaccharides
-
Performance analysis of power swing blocking feature in ABB 670 series impedance relays
PublikacjaThis paper presents test results of a distance protection’s PSD power swing detection feature in ABB 670 series relays. A RED670 relay was tested, which is part of the hydroelectric set protection in Żarnowiec Pumped Storage Plant. The power swing blocking feature’s performance was analysed on the basis of the results of object tests made with an Omicron digital tester. Also presented are simulation results that illustrate the...
-
Cough influence on fascia-mesh system built for a hernia repair - an experimental research
PublikacjaAn experimental approach to identify stronger and weaker fixation schemes in laparoscopic ventral hernia repair is presented in the paper. Two types of implants, whose mechanical properties are significantly different and five kinds of connectors are considered. Physical models of operated hernia have been built using those materials and porcine abdominal tissue. The models have been subjected to dynamic impulse load, similar to...
-
Electrical properties of hybrid planar diode based on palladium phthalocyanine and titanium dioxide
PublikacjaThis work details experimental studies of a planar diode made of indium tin oxide/titanium dioxide/palladium phthalocyanine/gold. The rectification ratio of current was 105 at 1.5 V. The analysis of the electrical properties of the system was based on small signal complex capacitance spectra measured in the frequency range of 25 Hz-1 MHz at different values of bias. No depletion region at the TiO2/PdPc interface was observed. Forward...
-
Investigation on water infiltration and water content changes in a large-scale experimental test dike
PublikacjaThe paper presents result of series of experiments made within the DREDGDIKES project, performed on a test dike built from composite soil. The composite is produced by mixing fly ash (by-product of energetics) with dredged material (sand) taken from the mouth of The Vistula river. The test dike, located near Gdansk in Poland, was subjected to hydraulic load in several flooding time scenarios and the unsaturated unsteady flow was...
-
Numerical estimation of the pile toe and shaft unit resistances during the installation process in sands
PublikacjaNumerical simulations of a pile jacking were carried out. A Coupled Eulerian–Lagrangian (CEL) formulation was used to treat with large deformation problems. An Abaqus, a commercial Finite Element Method software suit, was used as a computing environment. The Mohr–Coulomb constitutive model was applied and the Coulomb model of friction was used to describe pile-soil interaction. Calculations were made for three different pile diameters....
-
A method for counting people attending large public events
PublikacjaThe algorithm for people counting in crowded scenes, based on the idea of virtual gate which uses optical flow method is presented. The concept and practical application of the developed algorithm under real conditions is depicted. The aim of the work is to estimate the number of people passing through entrances of a large sport hall. The most challenging problem was the unpredicted behavior of people while entering the building....
-
An Analysis of the Relationship between the Architecture and the Structure of a Vessel on the Example of the Reconstruction Design Process of the Historical Sailing Yacht "General Zaruski" Carried Out between 2009 and 2012
PublikacjaThe article analyzes the relation between architecture and structure of a vessel on the example of the reconstruction design of a wooden sailing yacht "General Zaruski" built in Ekanӓs, Sweden in 1939. Based on the documentation of "Kaparen" (sister yacht), "Mloda Gwardia" (ex "General Zaruski") and the reconstruction classification project made by the authors, the impact of functional, spatial and aesthetic design objectives (e.g....
-
Polarization interferometer using a Liquid Crystalline Polymer waveplate for wavelength measurement
PublikacjaA two-beam polarization interferometer for measuring wavelength changes of a tunable semiconductor laser was designed, built and tested. This interferometer uses a λ/8 waveplate made from Liquid Crystalline Polymer in order to generate two output signals in quadrature. The λ/8 waveplate can be manufactured either on a beamsplitter face or on the mirror surface, reducing the cost and complexity of the optomechnical assembly. Experiment...
-
Application of virtual gate for counting people participating in large public events
PublikacjaThe concept and practical application of the developed algorithm forpeople counting in crowded scene is presented. The aim of the work is to estimatethe number of people passing towards entrances of a large sport hall. Thedetails of implemented the Virtual Gate algorithm are presented. The video signalfrom the camera installed in the building constituted the input for the algorithm.The most challenging problem was the unpredicted...
-
Formation of High Corrosion Resistant Nanotubular Layers on TitaniumAlloy Ti13Nb13Zr
PublikacjaThis paper presents results of oxidation tests and corrosion investigations of titanium alloy Ti13Nb13Zr performed at different conditions. The oxide layers have been formed by electrochemical method in 2M H3PO4 + 0.3% HF solution for 30 min. and 1 h at 20 V constantvoltage. The corrosion tests have been made by potentiodynamic method in Ringer`s solution at pH ranged between 3 and 7. It has been shown that the nano-oxide films,...
-
Preparation of nano-tubular oxide layers on titanium alloy Ti13Nb13Zr
PublikacjaThe article presents results of oxidation tests and corrosion investigations of titanium alloy Ti13Nb13Zr preformed at different conditions. The oxide layers have been formed using electrochemical method in 2M H3PO4 + 0,3% HF solution for 30 min. and 1h at 20V constant voltage. The corrosion tests heve been made with poteniodynamic method in Ringer's solution at pH ranged 3 and 7. It has been shown that the nano-oxide films, which...
-
Design criterion for hydrodynamic vortex separators
PublikacjaTechnical objects designing involves determination of geometrical parameters that characterize a given object. When the device is described by the differential equations, an inverse problem brings difficulties, as geometrical values sought condition the solution to the problem. Vortex separators can be designed by the "criterion method'. Firstly, a critical particle is distinguished such that bigger particles are removed from...
-
Search for the most useful geometry of an acoustic journal bearing
PublikacjaComputer simulations of a number of journal bearing’s geometries utilising acoustic levitation were carried out. The choice of the best geometry depended on the ability of a deformed shape, created by piezo-electric elements, to facilitate squeeze film ultrasonic levitation, and also to create three evenly distributed diverging aerodynamic gaps. Deformations of analysed variants of the bearing’s shape were generated by numerical...
-
Modal properties identification of a novel sandwich footbridge – Comparison of measured dynamic response and FEA
PublikacjaA modern sandwich composite footbridge made of high-tech materials, being an example of practical application of laminated composites in civil engineering, is presented. The in situ non-destructive testing of the footbridge, aiming to identify modal properties and pedestrian comfort, is described. The measured eigenmodes and eigenfrequencies are compared with numerically estimated values. Finite element analyses of the footbridge...
-
Approach to evaluation of time to the critical degradation of ship pipelines
PublikacjaIn the article an approach to the problem of estimating time to the critical degradation of ship pipelines is considered. Such an assessment would consist of six stages. The fundamental idea is to include to the estimation of time to failure of pipelines such elements like: materials that the pipelines are made, destructive physical phenomena taking place in them and applied means of protection. The result of that evaluation should...
-
Sparse vector autoregressive modeling of audio signals and its application to the elimination of impulsive disturbances
PublikacjaArchive audio files are often corrupted by impulsive disturbances, such as clicks, pops and record scratches. This paper presents a new method for elimination of impulsive disturbances from stereo audio signals. The proposed approach is based on a sparse vector autoregressive signal model, made up of two components: one taking care of short-term signal correlations, and the other one taking care of long-term correlations. The method...
-
Influence of nanoparticle concentration on thermal properties of thermal oil-MWCNT nanofluid
PublikacjaResults of the measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of thermal oil-MWCNT (TO-MWCNT) nanofluid have been presented. Nanoparticles were tested at the concentration of 0.001%, 0.005%, 0.01%, 0.05%, and 0,1% by weight. Thermal oil (TO) was selected as a base liquid, because of possible application in ORC systems as an intermediate heating agent. Multi-walled carbon nanotubes were used...
-
Evidence-Based Risk Management for Civil Engineering Projects Using Bayesian Belief Networks (BBN)
PublikacjaThe authors are seeking new methods for improving the efficiency of the investments associated with the maintenance and operation of existing civil engineering structures. It is demonstrated how the knowledge about the elements of construction and operation phases and their relationships, combined with monitoring data can be used for more effective management of the risks associated with civil engineering projects. The methodology...
-
A Model for Risk Assessment and Management of Construction Projects in Urban Conditions
PublikacjaThe authors are seeking new methods for improving the efficiency of the investments associated with the maintenance and operation of existing civil engineering structures. It is demonstrated how the knowledge about the elements of construction and operation phases and their relationships, combined with monitoring data can be used for more effective management of the risks associated with civil engineering projects. The methodology...
-
Formation of High Corrosion Resistant Nanotubular Layers on TitaniumAlloy Ti13Nb13Zr
PublikacjaThis paper presents results of oxidation tests and corrosion investigations of titanium alloy Ti13Nb13Zr performed at different conditions. The oxide layers have been formed by electrochemical method in 2M H3PO4 + 0.3% HF solution for 30 min. and 1 h at 20 V constantvoltage. The corrosion tests have been made by potentiodynamic method in Ringer`s solution at pH ranged between 3 and 7. It has been shown that the nano-oxide films,...
-
Count Data Modeling About Relationship Between Dubai Housing Sales Transactions and Financial Indicators
PublikacjaIn this study, illustrating and comparing the performances of count data models such as Poisson, negative binomial (NB), Hurdle and zero-inflated models for the determination of factors affected housing sales in Dubai. Model comparisons are made via Akaike’s information criterion (AIC), the Vuong test and examining the residuals. Main purpose of this study is building reliable statistical model for relationship between Dubai housing...
-
L’indistricabile intreccio. Imprese, imprenditori e regime fascista. (An Inextricable Intertwining. Companies, Entrepreneurs, and the Fascist Regime)
PublikacjaThe papers of this section analyse the relationships between the economic and business community and the fascist regime. Their aim is to refresh the interpretations that were established in the 1960s-1970s and remained undisputed in the decades thereafter, becoming a sort of mantra among Italian contemporary historians. The article presents the most relevant contributions of that historiographical season, explaining the reasons...
-
Economic benefits of dynamic charging of electric buses
PublikacjaDiesel engines buses are still the most used type of buses. Electric buses provide promising green alternatives and a lot of advantages, but their main disadvantages are limited travel range and long charging time. This article is a presentation of innovative solution for charging of electric busses - Dynamic Charging (IMC). The modern IMC system in Solingen was presented. At the end of the article, a proposal was made to introduce...
-
The use of machine learning for face regions detection in thermograms
PublikacjaThe aim of this study is to analyse the methods of detecting characteristic points of the face in thermographic images. As part of the implementation an extensive analysis of scientific publications covering similar issues both for the analysis of images made in visible light and thermographic images was carried out. On the basis of this analysis, 3 models were selected and then they were implemented and tested on the basis of...
-
Selected properties and parameters of radio channel impulse response estimation in ISM 2.4 GHz band
PublikacjaThe article presents experimental research indicating that the impulse response of the communication channel, determined in practice, are not of an universal character, but only represent its approximate value for the frequency on which this measurement was made. Phases for each of the replicas of the measurement signal were determined during the analysis of the received signals in the baseband. Phase changes of individual replicas...
-
Ultrasonic wave propagation, digital image correlation and X-ray micro-computed tomography measurements of concrete during splitting (cube #3)
Dane BadawczeThe DataSet contains the results of the mechanical behaviour of a concrete cube under the splitting test. The cube had dimensions 70 x 70 x 70 cm3 and was made of concrete with the following ingredients: cement type CEM I 42.5R (330 kg/m3), water (165 kg/m3), aggregate 0/2 mm (710 kg/m3), aggregate 2/8 mm (664 kg/m3), aggregate 8/16 mm (500 kg/m3),...
-
Ultrasonic wave propagation, digital image correlation and X-ray micro-computed tomography measurements of concrete during splitting (cube #1)
Dane BadawczeThe DataSet contains the results of the mechanical behaviour of a concrete cube under the splitting test. The cube had dimensions 70 x 70 x 70 cm3 and was made of concrete with the following ingredients: cement type CEM I 42.5R (330 kg/m3), water (165 kg/m3), aggregate 0/2 mm (710 kg/m3), aggregate 2/8 mm (664 kg/m3), aggregate 8/16 mm (500 kg/m3),...
-
Ultrasonic wave propagation, digital image correlation and X-ray micro-computed tomography measurements of concrete during splitting (cube #4)
Dane BadawczeThe DataSet contains the results of the mechanical behaviour of a concrete cube under the splitting test. The cube had dimensions 70 x 70 x 70 cm3 and was made of concrete with the following ingredients: cement type CEM I 42.5R (330 kg/m3), water (165 kg/m3), aggregate 0/2 mm (710 kg/m3), aggregate 2/8 mm (664 kg/m3), aggregate 8/16 mm (500 kg/m3),...
-
Ultrasonic wave propagation, digital image correlation and X-ray micro-computed tomography measurements of concrete during splitting (cube #2)
Dane BadawczeThe DataSet contains the results of the mechanical behaviour of a concrete cube under the splitting test. The cube had dimensions 70 x 70 x 70 cm3 and was made of concrete with the following ingredients: cement type CEM I 42.5R (330 kg/m3), water (165 kg/m3), aggregate 0/2 mm (710 kg/m3), aggregate 2/8 mm (664 kg/m3), aggregate 8/16 mm (500 kg/m3),...
-
Acoustic emission signals in concrete beams under 3-point bending (polyolefin and steel fibre concrete)
Dane BadawczeThe DataSet contains the results of the mechanical behaviour of concrete beams with dimensions 40 x 40 x 160 cm3 under the 3-point bending. All specimens were manufactured based on the same concrete mixture composed of cement CEM I 42.5R (380 kg/m3), water (165 kg/m3), aggregate 0/2 mm (648 kg/m3), aggregate 2/8 mm (426 kg/m3), aggregate 8/16 mm (754...
-
Localization and identyfication of ferromagnetic objects
PublikacjaA compact ferromagnetic object placed in the earthly magnetic field causes disturbance of this field. This disturbance is associated with magnetization of the object. Ferromagnetic objects have induced and can also have permanent magnetization. In methods of locating and identifying ferromagnetic objects usually is using the model of the dipol moment. Determination of the position and values of the extremes of the magnetic field...
-
Analysis of sloping brace stiffness influence on stability and load bearing capacity of a truss
PublikacjaThe paper is focused on the numerical study of stability and load bearing capacity of a truss with side elastic braces. The structure is made in reality. The rotational and sliding brace stiffnesses were taken into account. Linear buckling analysis and non-linear static analysis with geometric and material nonlinearity were performed for the beam and shell model of the truss with respect to the angle of sloping braces. As a result...
-
THE PHASE SHIFTERS INFLUENCE ON THE POWER SYSTEM STABILITY
PublikacjaThe paper presents the effect of phase shifters as FACTS devices on the possibility of improving the angle stability. Presented results obtained by the dynamic simulation performed on the mathematical model of the three machine system cooperating with the 400 kV network. The generative blocks models include turbine models with their controllers and models of synchronous generators with their excitation systems and voltage regulation....
-
A handwritten signature verification method employing a tablet
PublikacjaA signature verification system based on static features and time-domain functions of signals obtained using a tablet has been presented in the paper. The signature verification method, based mainly on dynamic time warping coupled with some signature image features, has been described. The FRR measures reflecting the method's efficiency have been evaluated for verification attempts performed directly after obtaining model signatures...
-
On the modelling of aerodynamic force coefficients for over-shroud seals of turbine stages
PublikacjaThis paper presents experimental investigations which made it possible to determine dynamic coefficients of labyrinth over-shroud seal of a model air turbine. The coefficients associate pressure forces with turbine rotor displacement, velocity and acceleration respective to turbine casing (linear model) and play important role in analyzing turbine-set dynamics. The obtained results indicated that involving serious errors can be...
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublikacjaIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (),were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublikacjaIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (s), were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
Determination of Mechanical Properties of P91 Steel by Means of Magnetic Barkhausen Emission
PublikacjaIn this work, an attempt at determination of mechanical properties by means of a method based on magnetic Barkhausen emission measurements was proposed. The specimens made of P91 steel were subjected to creep or plastic flow which were interrupted after a range of selected time periods in order to achieve specimens with an increasing level of strain. Subsequently, measurements of magnetic Barkhausen emission were carried out, and...
-
Modeling of truss with cold-formed section and positive eccentricity in the node
PublikacjaThis work is dedicated to establishing the load carrying capacity of tensed and compressed truss’ nodes made of cold-formed open cross sections. The occurrence of bending in the truss’ nodes is the result of a specific production technology for system lattice girders assumed by the designer and the producer. The aim of this research is to present the methodology of conduct for creation of computational models that best depict the...
-
“Project-factor-decision”. Decisive factors in IT projects and their impact on its success
PublikacjaThe aim of this article is to indicate the need for a deepening, systematizing and codifying of the theoretical and practical knowledge on IT project management, in the area of management decision-making processes. The scope of decisions made by managers is constantly on the increase. Project managers make decisions not only within the classic triangle of constraints, which consists of a schedule, a budget and the project scope,...
-
Diffusible hydrogen content in deposited metal of multilayer welded joints
PublikacjaThe article describes manufacturing technology of multilayer joints in terms of control the diffusible hydrogen content. Diffusible hydrogen content in deposited metal for multilayer welded joints made of covered rutile electrodes or covered cellulosic and basic electrodes was determined. It was found that after four beads, the diffusible hydrogen content decreases in the case of the first technology from 36 ml/100 g to 18 ml/100...
-
Determination of Failure Causes of a Steam Turbine Casing
PublikacjaThe paper presents results of research and failure analysis undertaken to determine failure causes of a steam turbine casing. After 130,000 hours of service the crack in a outer shell of the turbine casing was found. The inner shell of the casing was made of cast steel grade G21CrMoV5-7, and the outer shell of grade G20CrMo4-5. Following research were performed in order to determine causes of the casing failure: chemical analysis;...
-
Numerical solutions for large deformation problems in geotechnical engineering
PublikacjaThe problem of large deformations often occurs in geotechnical engineering. Numerical modeling of such issues is usually complex and tricky. The chosen solution has to implicate soil-soil and soil-structure interactions. In this paper, a review of the most popular numerical methods for large deformation problems is presented. The Coupled Eulerian-Lagrangian (CEL) method, the Arbitrary Lagrangian-Eulerian (ALE) method, the Smoothed...
-
Shaping of the turnout diverging track with variable curvature sections
PublikacjaThe paper presents an analytical method of shaping the turnout diverging railroad track with variable curvature segments on its length, which in an evident way distinguished it from a typical solution, made up of a single circular arc with no transition curves. Two separate causes including a linear and a nonlinear curvature one in the form of a polynomial have been examined. The obtained solutions of the problem have a universal...
-
Influence of an applied bearing system on behaviour of multi-span footbridge
PublikacjaThe cycle overpass in Gdynia is a box structure over 300 metres long, 10-span. It was opened for bicycle traffic in the second half of 2013. At the end of its construction, there was failure due to excessive horizontal displacement of the system. A number of bearings exceeded the range of permissible transverse shifts thus it was necessary to temporarily protect the spans from slipping. The FEM analysis of the original solution...
-
Determinants of the surface quality, density and dimensional correctness in selective laser melting of the Ti-13Zr-13Nb alloy
PublikacjaSelective laser melting is widely used for custom-designed elements. Successful manufacturing depends on laser treatment parameters and material features. This research aimed to determine the effects of laser power, scan time and hatch distance on surface quality, relative density and dimensional precision for cuboids made of the Ti-13Zr-13Nb alloy. The influence of energy density, energy flux and pre-heating was seen to be decisive...
-
Proton transfer reactions for ionized water clusters
PublikacjaCalculations of formation energies of the ionized water clusters and energies of reactions between small (including less than eight water molecules) neutral and positively ionized water clusters are presented. Moreover, we discuss some reaction paths between neutral and positively charged dimers, trimers and tetramers and proton transfer reactions (PTR) between cyclic clusters and H3O+ ions which can appear in beam experiments...
-
Roof over PGE Arena in Gdansk. Review of structure and monitoring system
PublikacjaThis paper presents general structural assumptions of the steel construction designed for a newfootball stadium to be built for UEFA Championship 2012 in the city of Gdańsk. The superstructureis founded directly on the modified abutment. The facade and the roof are collected from 82 steelgirders made of tube profiles. The girders are braced by circular beams and X tension rods. All thiscreates a quasi - dome covered by polycarbonate...
-
Analysis of soundscape recordings in close proximity to the road in changeable wather conditions
PublikacjaThe acoustic vehicle sensing is the least invasive type of traffic detection. Also, acoustic-based vehicle detection technology is insensitive to precipitation and can operate in low light level. Therefore, this kind of method may be used for automatic detection of the vehicle passage events. It can also be employed for measurements of a vehicle speed and the vehicle assignment to the particular category. In this paper the results...
-
Influence of vacuum sublimation deposited metal layer thickness on metrological parameters of the amperometric gas sensor with Nafion membrane
PublikacjaThe paper presents the results of investigation on an influence of vacuum sublimation deposited platinum layer thickness on the signal, sensitivity and response time of a prototype of sulphur dioxide sensor with Nafion membrane. The working electrode was made by vacuum sublimation deposition of platinum on a surface of Nafion membrane. Pt layers deposited changed an initial structure of Nafion membrane and that phenomenon was utilized...