Wyszukiwarka
Filtry
wszystkich: 868
-
Katalog
Wyniki wyszukiwania dla: GLASS-PLY CRACKING
-
On degradation of glass/polyester laminate immersed in water
PublikacjaMechanical behaviour was compared for glass/ polyester laminates manufactured in the boatbuilding plant using three methods: hand lay-up, vacuum bagging, infusion. Specimens were tested in dry condition and following accelerated water immersion test (70°C- corresponding to the exposure of 30 years at 19°C). In three point bending test 40-50% reduction in laminate strength was observed due to water immersion. The highest degradation...
-
Sulfate‐reducing bacteria‐assisted hydrogen‐induced stress cracking of 2205 duplex stainless steels
PublikacjaThe paper presents the results of a laboratory investigation of the microbiologically assisted hydrogen‐induced stress cracking (HISC) of 2,205 duplex stainless steel (DSS). The testing of susceptibility toward HISC was performed with two different methods. Precharged in sulfate‐reducing bacteria (SRB), inoculated medium samples were subjected to slow strain‐rate testing in artificial seawater. In situ constant load tests were...
-
The Issue of Shading Photovoltaic Installation Caused by Dust Accumulation on the Glass Surface
PublikacjaThe issue of accumulation of dust and other pollutants on the surface of photovoltaic modules was thoroughly analysed over the years. One of the first surveys in this field of knowledge linked pollutant accumulation on the module surface with transmittance loss of its glass covering, which leads to lessened amount of solar radiation reaching solar cells. First stage of this accumulation process is linear transparency loss, and second...
-
Ho2Pd1.3Ge2.7 – a ternary AlB2-type cluster glass system
PublikacjaWe report a successful synthesis of a ternary AlB2-type intermetallic compound. The phase purity was obtained by fine-tuning the Pd-Ge ratio out of the idealized 1-3. Attempts to synthesize an Er analogue were not successful. We discuss the instability of the Er analogue based on the atomic size ratio and also suggest that the increased stability of Ho2Pd1+xGe3−x in the Pd-rich range likely stems from a combination of atomic size...
-
Effect of porosity on physical properties of lightweight cement composite with foamed glass aggregate
PublikacjaThis paper reports on a study of physical properties of lightweight cement composite. We investigate the possibility of replacing traditional aggregate with Granulated Ash Aggregate (GAA) and above all with Granulated Expanded Glass Aggregate (GEGA). For this purpose, 15 specimens of different percentage share of each aggregate in total aggregate volume were tested: 0%, 25%, 50%, 75% or 100% of foam glass aggregate (GEGA) partially...
-
Enhancing electrical properties through in-situ controlled nanocrystallization of V2O5–TeO2 glass
PublikacjaV2O5–TeO2 glass–ceramics (VTGC) were prepared by controlled annealing of the V2O5–TeO2 glass (VTG), which illustrates a parent glass matrix with a single charge carrier. The annealing proceeded at six temperatures selected between the glass transition and the maximum of the frst crystallization process to obtain various nanocrystallite sizes. Heat treatment caused an increase in DC conductivity by 2.5–3.5 (250–285 °C) order of...
-
Eu3+ doped tellurite glass ceramics containing SrF2 nanocrystals: Preparation, structure and luminescence properties
PublikacjaEu3+ doped tellurite glass ceramics containing SrF2 nanocrystals were prepared using melt quenching technique and subsequent heat treatment of glass in 370 °C for different time periods. Thermal properties of glass matrix have been determined based on DSC measurements. XRD and XPS results confirmed formation of SrF2 nanocrystals in glass matrices after annealing at 370 °C. FTIR studies revealed absorption bands in the range of...
-
Glass-ceramic joining of Fe22Cr porous alloy to Crofer22APU: interfacial issues and mechanical properties
PublikacjaThis work deals with the joining of porous Fe22Cr ferritic stainless steel to a dense Crofer22APU plate by using a silica-based, Ba-containing glass-ceramic. The chemical and interfacial stability and the mechanical properties of the joints were evaluated before and after thermal ageing at 700 ◦C for 500hrs. The sintering behaviour of the glass was assessed by using heating stage microscopy (HSM) to study the influence of a porous...
-
Lightweight glass and metal roof structures in the 19th century. Architecture and construction.
PublikacjaThe 19th century brought new construction possibilities. The usage of metal elements in mesh structures, filled in with glass, resulted in creating entirely new types of objects. They have distinguished themselves in architecture and technical solutions. The envelope structures giving spatial interiors were arising very quickly. They have been enabling large light penetration, triggering them extremely bright. Thus these building...
-
Application of lightweight cement composite with foamed glass aggregate in shell structures
PublikacjaThe purpose of the paper is to investigate the abilities of applying Granulated Expanded Glass Aggregate (GEGA) as a natural volume substitute of aggregate as a component of lightweight concrete. The GEGA aggregates used in the experiments were made of confused glass waste. In order to achieve satisfactory strength of concrete Granulated Ash Aggregate (GAA) was added as well. To produce specimens three grain sizes of aggregates...
-
Mechanical, thermo-mechanical properties of epoxy/glass composites with submicron particles
PublikacjaIn this research the influence of submicron zinc oxide and silicon dioxide particles on mechanical, thermo-mechanical properties of epoxy matrix composites reinforced with glass fibres was investigated. Composites were fabricated using hand lay-up method. Materials contained 39-41 wt.% of glass fibres. The bending tests, dynamic mechanical analysis and tribological tests were performed on each group of composites and also for...
-
A novel approach for processing CaAlSiON glass-ceramics by spark plasma sintering: Mechanical and electrical properties
PublikacjaLithium containing glassy materials can be used as solid electrolytes or electrode materials for lithium-ion batteries due to their high energy density. Conventional melt-quenched Ca11Al14Si16O49N10 glass powder containing 24 e/o N, doped with Li-ions (1, 3, and 6 wt. %) and sintered by spark plasma sintering technique (SPS) was studied. The benefits of using SPS to produce glass-ceramics are rapid heating rates compared to conventional...
-
Evaluating the impact of ZnO doping on electrical and thermal properties of calcium-aluminosilicate oxynitride glass-ceramics
PublikacjaThis study aimed to investigate the impact of ZnO content on the structure, thermal, and electrical properties of oxynitride glass-ceramic(s) within the Ca–Al–Si–O–N (CASON) system. The base glass had the composition of Ca7Al14Si17O52N7, with ZnO additions ranging from 3 to 15 % by weight. A pristine Ca7Al14Si17O52N7 glass was successfully prepared by melt-quenching technique followed by converted into glass-ceramic by incorporating various...
-
Structural and luminescence properties of B2O3-Bi2O3-AlF3 glass doped with Eu3+, Tb3+ and Tm3+ ions
PublikacjaThe B2O3-Bi2O3-AlF3 glass system doped with Eu3+, Tb3+, Tm3+ and triply doped with Eu3+/Tm3+/Tb3+ ions in different molar ratios were successfully synthesized. Glass transition and crystallization temperatures were examined by Differential Scanning Calorimetry (DSC) measurements. X-ray Diffraction (XRD) confirmed the amorphous character of the samples. Fourier Transform Infrared Spectroscopy (FTIR) revealed that the glass matrix...
-
Investigation of polyurethane elastomer–steel joints using glass lacquer as an adhesive agent
PublikacjaThis article describes an innovative method of coupling polyurethane elastomer (based on polyurethane glycolysate) with constructional steel, by implementation of a Glaspur®—glass lacquer containing latent polyurethanes and monosilane adhesion promoters. The commonly applied coupling agent is Cilbond® 45SF glue or its derivatives. Additionally, glycolysate was synthesised from polyurethane waste and 1,3-propylene glycol in 6:1...
-
Blue Upconversion Emission in Germanate Glass Co‐Doped with Yb3+/Tm3+ Ions
Publikacja -
Spectroscopic properties of Eu-doped antimony-germanate glass and glass-ceramics
Publikacja -
Mixed ionic-electronic conductivity and structural properties of strontium-borate glass containing nanocrystallites of Bi2 VO5.5
PublikacjaSamples of strontium borate glass containing bismuth vanadate nanocrystallites were prepared. Nanocomposites containing up to 45mol% of the Bi2VO5.5 phase exhibit electrical properties closer to the strontium-borate glass than to the ferroelectric Bi2VO5.5 ceramic. The glass matrix still may contain some part of bismuth and vanadium ions even after crystallization process and there is too little of crystalline phase to observe...
-
Correlations of structural, thermal and electrical properties of sodium doped complex borophosphosilicate glass
PublikacjaBorophosphosilicate glasses with varying sodium ion concentrations were investigated for their, structural, thermal, and electrical properties. All the obtained glasses were transparent except the glass with the highest sodium content, which exhibited translucency due to inhomogeneities. Increasing sodium content led to reduced boron and silicon content while maintaining a constant B/Si ratio, indicating progressive depolymerization...
-
Influence of concentration on contact angle of water-Cu nanofluid on glass substrate
PublikacjaIn the paper the results of an experimental investigation of influence of nanoparticle concentration on contact angle of water-Cu nanofluid on glass substrate have been presented. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight. In the present study copper was applied as nanoparticle while distilled, deionized water was used as a base fluid. The mean diameter of nanoparticle is estimated to be 50...
-
Spin-glass behavior in a binary Pr 3 Ir intermetallic compound
PublikacjaPolycrystalline Pr3Ir was synthesized by arc melting. Its cementite-type crystal structure (Pnma) was confirmed by powder X-ray diffraction and estimated lattice parameters are in agreement with literature. Physical properties were measured by means of the ac and dc magnetic susceptibility, electrical resistivity and heat capacity. Our results indicate spin-glass behavior in Pr3Ir with a freezing temperature Tf = 6.58 K and activation...
-
Role of MnO in manganese–borate binary glass systems: a study on structure and thermal properties
PublikacjaStructural and thermal properties of x MnO−(100−x)B2O3 (where x=40, 50 and 60 mol%) glass samples have been investigated with the employment of various techniques. Fourier transform infrared spectroscopy results revealed the influence of MnO on glass matrix. Decrease of B–O bond-related band intensities has been observed. MnO addition was found to introduce broken [BO2O−]n chains. Differential scanning calorimetry (DSC) measurements...
-
Resistance to cold cracking of steel joints of P460NL1 steel
PublikacjaPrzedstawiono wyniki badań odporności na zimne pękanie złączy spawanych ze stali przeznaczonej do pracy pod ciśnieniem. Badano równoczesny wpływ zawartości wodoru dyfundującego i energii liniowej na naprężenie krytyczne w próbie implant dla złączy spawanych elektrodami otulonymi i drutem proszkowym w osłonie gazów ochronnych. Stwierdzono wpływ energii liniowej jak i zawartości wodoru dyfundującego na odporność na zimne pękanie...
-
Hydrogen delayed cracking of high-strength weldable steels
PublikacjaOceniano podatność na niszczenie wodorowe stali 14HNMBCu o wysokiej wytrzymałości i jej połączeń spawanych przy obciążeniu stałym w wodzie morskiej. Badania przeprowadzono w powietrzu, oraz w środowisku wody morskiej przy potencjale korozyjnym i przy polaryzacji katodowej. Obecność lub brak opóźnionych pęknięć próbek z karbem przyjęto za miarę odporności na niszczenie wodorowe przy stałym obciążeniu.
-
Tunable emission and energy transfer of B2O3–Bi2O3–AlF3 glass system doped with Eu3+/Dy3+
PublikacjaThe structure and luminescent properties of the B2O3–Bi2O–AlF3 glass system doped with Eu3+/Dy3+ ions in different molar ratios were studied. A series of glasses were synthesized by the conventional melt quenching technique. Glass transition and crystallization temperatures were examined by Differential Thermal Analysis (DTA) measurements. The amorphous character of the prepared samples was confirmed by the X-ray diffraction (XRD)...
-
Submicron inorganic particles as an additional filler in hybrid epoxy matrix composites reinforced with glass fibres
PublikacjaIn this study, the effect of selected submicron metal oxide (zinc oxide, titanium oxide) or non-metal oxide (silicon dioxide) particles on mechanical and thermo-mechanical properties of epoxy/glass composites was investigated. The applied epoxy resin was a diglycidyl ether of bisphenol-A cured with triethylenetetramine. As a reinforcement twill weave E-glass fabric was used. Hybrid composites (contained particulate and fibrous...
-
Structure and magnetic properties of BeO-Fe2O3-Al2O3-TeO2 glass-ceramic composites
PublikacjaIn this work, glass-ceramics in the xBeO–20Fe2O3–(80-x)TeO2 system with x = 0–25 mol% were synthesized by the traditional melt quenching route and studied by inductively coupled plasma optical emission spectroscopy, X-ray diffraction, confocal microscopy, infrared and Raman spectroscopy. BeO addition was found to support the crystallization process of Fe2O3 during melting, and an increased BeO content was associated with an increased...
-
Nonlinear Impedance as Possible Result of Ion-Polaron Interaction in Cu2O-Al2O3-SiO2 Glass
PublikacjaNonlinear a.c. impedance measurements were performed in Cu2O-Al2O3-SiO2 glass in wide frequency range. The obtained results shows that a large nonlinearity in the impedance signal is observed at moderate electric fields of an order 1V/mm. The contents of the third harmonics reaches about 10% and strongly depends on temperature and frequency. The investigated glass exhibits mixed electronic-ionic conductivity. Electronic conduction...
-
Glass-ceramic sealants and steel interconnects: accelerated interfacial stability and reactivity tests at high temperature
PublikacjaHigh-temperature reactions between glass-ceramic sealants and Fe-Cr alloy interconnects may lead to the formation of undesirable phases, and consequently degradation of solid oxide fuel/electrolyser devices. In this work, three different glass-ceramic sealants (Na-containing, Ba-containing, Sr-containing compositions) and Fe22Cr stainless steel powders (raw and pre-oxidised) are considered in order to test their chemical reactivity...
-
Improvement of glass break acoustic signal detection via application of wavelet packet decomposition
PublikacjaThe main subject of the authors' research are non-contact methods of glass break detection based on analysis of the acoustic signal generated during the event. This problem has essential meaning for modern cost- effective alarm systems, particularly those installed into big buildings. The main difficulties of the matter are: transient character of the signal, great number of similar sounds (false signals, mainly accidental glass...
-
Increasing the conductivity of V2O5 -TeO2 glass by crystallization: structure and charge transfer studies
PublikacjaIn the present paper, V2O5-TeO2 glass...
-
From structure to luminescence investigation of oxyfluoride transparent glasses and glass-ceramics doped with Eu3+/Dy3+ ions
PublikacjaGlasses and glass-ceramics with nominal composition 73 TeO2– 4BaO– 3Bi2O3–18SrF2-2RE2O3 (where RE = Eu, Dy) have been synthesized by conventional melt-quenching technique and subsequent heat treatment at 370 °C for 24 h in air atmosphere. Various Eu3+ to Dy3+ molar ratio have been applied to investigate luminescence properties in both glass and glass-ceramic matrices. Especially, white light emission through simultaneous excitation...
-
The research of glass-ceramics implants used for bone pitches to examine bacteria adhesion occuring in human body
PublikacjaThe paper deals with the research concerning the bacteria adhesion on bioactive glass - ceramics materials
-
Mechanism of hopping conduction in Be–Fe–Al–Te–O semiconducting glasses and glass–ceramics
PublikacjaElectrical properties of beryllium-alumino-tellurite glasses and glass–ceramics doped with iron ions were studied using impedance spectroscopy. The conductivity was measured over a wide frequency range from 10 mHz to 1 MHz and the temperature range from 213 to 473 K. The D.C. conductivity values showed a correlation with the Fe-ion concentration and ratio of iron ions on different valence states in the samples. On the basis of...
-
Micro-cracking pattern recognition of hybrid CNTs/GNPs cement pastes under three-point bending loading using acoustic emission technique
PublikacjaThe generation of microcracks has an important influence on the behaviour of concrete structures. In this study, the acoustic emission (AE) technique was used to investigate the fracture phenomena and micro-cracking behavior of hybrid carbon nanotubes (CNTs, the 1-D allotrope of carbon atoms) and graphene nanoplatelets (GNPs, 2D monolayer of sp2-hybridized carbon atoms), cement composites under three-point bending loading. In...
-
Degradation of Gel-Coat Layer in Glass/Polyester Laminate in Seawater Environment
PublikacjaGlass/polyester laminate coated with gelcoat layer of different thickness 0,5; 1,5; 3 mm was studied in terms of blistering behaviour and water sorption in hot water environment. Blistering was found to be accelerated for thin (0,5 mm) gel-coat layer compared to the thick (1,5; 3 mm), however no significant difference in blistering behaviour was observed between the laminates with gel-coat thickness 1,5 and 3 mm which may suggest...
-
Factors affecting low-temperature cracking of asphalt pavements: analysis of field observations using the ordered logistic model
PublikacjaAccurate identification of factors that primarily affect the number of low-temperature cracks is crucial for selection of road materials and planning of pavement maintenance. Field investigations of lowtemperature cracks were performed in the years 2014 and 2020 on the same 68 road sections being in service in typical traffic conditions. The collected data were statistically analysed using the ordered logistic regression model....
-
The effect of lithium fluoride on the thermal stability and thermoluminescence properties of borosilicate glass and glass-ceramics
Publikacja -
Barium boron aluminum silicate glass system for solid state optical gas sensors
PublikacjaRecent increasing demand for new eco-friendly materials and for low cost fabrication process for use in optical sensors field, raise concern about alternative materials for this application. We have designed two glass-ceramics compositions from the quaternary ROAl2O3- SiO2-B2O3(R=Ba) alkali-earth aluminum silicate system, labeled B72 and B69, with high refractive index (>1.6), large values of Abbe number (94.0 and 53.0, respectively),...
-
Influence of burnishing on stress corrosion cracking susceptibility of duplex steel
PublikacjaNa próbkach ze stali duplex poddanych procesom nagniatania przeprowadzono badania podatności do naprężeniowego pękania korozyjnego. Przeprowadzono testy odkształcania z małą prędkością w środowisku wrzącego 35% MgCl2 i środowisku obojętnym- glicerynie. Stwierdzono zwiększoną odporność korozyjną stali po procesach nagniatania z niewielkim stopniem zgniotu. Stwierdzono, że zgniot powierzchniowy ma wpływ na przebieg procesu korozyjnego...
-
Surface cracking of laser melted Ti-6Al-4V alloy
PublikacjaOpisano charakterystyczne cechy pękania powierzchniowego obserwowanego po nadtapianiu laserem CO2 i Nd:YAG stopu Ti-6Al-4V. Obserwowano pęknięcia niezależnie od sposobu nadtapiania, penetrujące głęboko strefę przetopioną i w niewielkim stopniu zależne od sposobu nadtapiania. Przypisano obserwowane zjawisko przemianie martenzytycznej i (lub) naprężeniom cieplnym powstającym podczas gwałtownego chłodzenia.
-
Investigation of transverse cracking of asphalt pavements in the north-eastern Poland
PublikacjaSpękania poprzeczne są jednym z najczęstszych typów uszkodzeń występujących na polskich drogach. Artykuł przedstawia wyniki badań spękań poprzecznych dróg zlokalizowanych w Polsce północno-wschodniej. Na podstawie badań terenowych podjęto próbę wyznaczenia związków pomiędzy częstotliwością spękań, zdefiniowaną indeksem spękań, a wybranymi cechami nawierzchni. Analizowane były następujące cechy nawierzchni: typ podbudowy (podbudowa...
-
Applications of electrochemical noise technique in stress corrosion cracking diagnosis
PublikacjaW pracy przedstawione zostały rezultaty analizy prądowego szumu elektrochemicznego, generowanego podczas korozji naprężeniowej próbek stali stopowej. W przeciwieństwie do tradycyjnych metod analizy nie zakładano stacjonarności analizowanych sygnałów. Zamiast tego analizie poddana została zmodyfikowana widmowa odpowiedź szumowa o charakterze zależnym od czasu. Rezultaty badań skonfrontowano z wynikami otrzymanymi za pomocą techniki...
-
Pitting corrosion and stress-corrosion cracking of buffer tanks in a brewery
PublikacjaW pracy przedstawiono wyniki ekspertyzy zbiornika magazynowego na ciepłą wodę do produkcji piwa w browarze. Zbiornik uległ przyśpieszonym procesom korozyjnym, które doprowadziły do jego perforacji. Podczas eksploatacji zbiornika wystąpił proces korozji wżerowej oraz pękania korozyjnego. Przyśpieszone procesy korozyjne zbiornika związane były z wysoką zawartością jonów chlorkowych w wodzie oraz statycznymi naprężeniami mechanicznymi....
-
Hydrogen delayed cracking of high-strength 14hnmbcu steel in seawater
PublikacjaOceniano podatność na niszczenie wodorowe stali o wysokiej wytrzymałości i jej połączeń spawanych przy stałym obciążeniu w wodzie morskiej. Badania przeprowadzono na próbkach okrągłych z karbem w środowisku wody morskiej przy potencjale korozyjnym oraz przy polaryzacji katodowej. Badano stal gatunku 14HNMBCu o minimalnej granicy plastyczności 690 MPa oraz jej połączenia spawane automatycznie łukiem krytym i ręcznie łukowo elektrodą...
-
Evaluation of susceptibility of high-strength steels to hydrogen delayed cracking
PublikacjaPrzedstawiono wyniki badań podatności na opóźnine pękanie wodorowe stali o wysokiej wytrzymałości w oparciu o próbę stałego obciążenia. Badano stal do pracy w podwyższonych temperaturach 26H2MF oraz stal do ulepszania cieplnego 34HNM w środowisku przepracowanego oleju silnikowego. Badano również stal 14HNMBCu i jej złącza spawane w środowisku wody morskiej przy polaryzacji katodowej.
-
Structure, luminescent properties and FDTD simulation of TeO2-BaO-Bi2O3-Ag:Ln3+ glass-ceramics system
PublikacjaTeO2-BaO-Bi2O3-Ag glass systems (TBB) co-doped with terbium and europium ions have been successfully synthesized through conventional melt-quenching technique. Heat treatment procedure at 350 °C has been conducted in order to synthesize silver nanoparticles embedded in TBB glass matrix. Structural measurements involved XRD studies that revealed no crystallization of glass structure after heat treatment at elevated temperatures....
-
Field investigation of low-temperature cracking and stiffness moduli on selected roads with conventional and high modulus asphalt concrete
PublikacjaHigh Modulus Asphalt Concrete (HMAC) was introduced in Poland as a one of the solutions to the problem of rutting, type of deterioration common in the 1990s. After first encouraging trials in 2002 HMAC was widely used for heavily loaded national roads and motorways. However some concerns were raised about low-temperature cracking of HMAC. This was the main reason of the studies presented in this article were started. The article...
-
Heat treatment effect on Eu3+ doped TeO2-BaO-Bi2O3 glass systems with Ag nanoparticles.
PublikacjaGlass systems of 73TeO2-4BaO-3Bi2O3-2Eu2O3-xAg ( in molar ratio where x= 0, 1, 2, 3) compositions have been successfully synthesized. Silver nanoparticles were obtained with the employment of heat treatment (HT) procedure executed at 350 °C. Glass transition temperatures of different compositions have been determined through DSC measurements. XRD measurement results presented characteristic amorphous halo indicating lack of long...
-
Influence of selected submicron inorganic particles on mechanical and thermo-mechanical properties of unsaturated polyester/glass composites
PublikacjaIn this paper, the influence of different submicron-scaled particles (zinc oxide, titanium dioxide, or silica) on mechanical and thermo-mechanical properties of unsaturated polyester matrix composites reinforced with glass fabric was investigated. Surface morphology of obtained composites was also examined. At first inorganic particles were mechanically dispersed into unsaturated polyester resin system as per the calculated weight...