Wyszukiwarka
Wyniki wyszukiwania dla: NUMERICAL MODELLING
-
On the influence of the acceleration recording time on the calculation of impact severity indexes
PublikacjaThe paper concerns with the analysis of normative requirements pertaining to experimental setup of a crash test and its numerical modelling. An overview of parameters describing the collision of a vehicle with a road restraining system is presented. A short description of a concrete road safety barrier is presented. A brief description of numerical modelling procedures for crash tests is given as well. The parametric influence...
-
Modelling of elastic wave propagation in a bolted joint using a thin layer of shell elements
PublikacjaThere are many mathematical models describing the propagation of elastic waves through the imperfect boundary of two media. They were successfully applied to modelling of high frequency bulk waves and their interaction with local defects. On the other hand, the existing literature models of bolted connections ignore the aspect of imperfect connection between elements. Therefore, this paper presents the concept of application of...
-
Modelling of Longitudinal Elastic Wave Propagation in a Steel Rod Using the Discrete Element Method
PublikacjaThe paper deals with the issue of modelling elastic wave propagation using the discrete element method (DEM). The case of a longitudinal wave in a rod with a circular cross-section was considered. A novel, complex algorithm consisting of the preparation of models and simulation of elastic waves was developed. A series of DEM models were prepared for simulations, differing in discretisation and material parameters. Additional calculations...
-
Spectral Methods for Modelling of Wave Propagation in Structures in Terms of Damage Detection—A Review
PublikacjaModern methods of detection and identification of structural damage direct the activities of scientific groups towards the improvement of diagnostic methods using for example the phenomenon of mechanical wave propagation. Damage detection methods that use mechanical wave propagation in structural components are extremely effective. Many different numerical approaches are used to model this phenomenon, but, due to their universal...
-
Dynamic analysis of lightweight structure of the Viaduct Millau in France subjected to the wind fluctuations described by Karman’s and Davenport’s spectrum
PublikacjaThe article presents numerical simulations for wind impact modelling on the Millau Viaduct structure in France performed with two independent spectrum generation methods. The viaduct's construction in affected by strong forces, as it is situated in the Tarn river's valley. Thus, the loading coming from the wind cannot be modelled, the way it is in case of simple structures as static loading, but as a loading in a form of a spectrum...
-
Thermal-FSI modeling of flow and heat transfer in a heat exchangerbased on minichanels
PublikacjaIn this paper selected numerical modelling problems for an advanced thermal-FSI ("Fluid Solid Interaction") mini-channel heat exchanger model are presented. Special attention is given to the heat transfer between the separated mediums for different mass flows. Similar modelling problems have also been discussed in the literature dedicated to numerical and theoretical modelling problems for typical heat exchangers [1, 2, 3]. Basic...
-
Three dimensional simulations of FRC beams and panels with explicit definition of fibres-concrete interaction
PublikacjaHigh performance concrete (HPC) is a quite novel material which has been rapidly developed in the last few decades. It exhibits superior mechanical properties and durability comparing to normal concrete. HPC can achieve also superior tensile performance if strong fibres (steel or carbon) are implemented in the matrix. Thus, there exist the unabated interest in studying how the addition of different types of fibres modifies the...
-
Numerical simulation of the influence of the selected factors on the performance of a concrete road barrier H2/W5/B
PublikacjaThis paper discuss the influence of selected factors on the performance of a concrete road barrier H2/W5/B. Modelling techniques of a concrete road safety system were briefly discussed. Comparison to the full scale crash test results has been shown. The concrete road safety barrier has been investigated for evaluation of the overall damage after collision under various initial conditions. The failure assessment criterion has been...
-
3D MODELLING OF CYLINDRICAL-SHAPED OBJECTS FROM LIDAR DATA - AN ASSESSMENT BASED ON THEORETICAL MODELLING AND EXPERIMENTAL DATA
PublikacjaDespite the increasing availability of measured laser scanning data and their widespread use, there is still the problem of rapid and correct numerical interpretation of results. This is due to the large number of observations that carry similar information. Therefore, it is necessary to extract from the results only the essential features of the modelled objects. Usually, it is based on a process using filtration, followed by...
-
Micro-modelling of shear localization during quasi-static confined granular flow in silos using DEM
PublikacjaThe paper deals with the quasi-static confined flow of cohesionless sand in a plane strain model silo with parallel walls and a slowly movable bottom. Numerical modelling was carried out by the discrete element method (DEM) using spheres with contact moments to approximately capture a non-uniform shape of sand particles. Different initial void ratios of sand and silo wall roughness grades were employed. Regular triangular grooves...
-
Sensitivity analysis based on non-intrusive regression-based polynomial chaos expansion for surgical mesh modelling
PublikacjaThe modelling of a system containing implants used in ventral hernia repair and human tissue suffers from many uncertainties. Thus, a probabilistic approach is needed. The goal of this study is to define an efficient numerical method to solve non-linear biomechanical models supporting the surgeon in decisions about ventral hernia repair. The model parameters are subject to substantial variability owing to, e.g., abdominal wall...
-
3-D finite-difference time-domain modelling of ground penetrating radar for identification of rebars in complex reinforced concrete structures
PublikacjaThis paper presents numerical and experimental investigations to identify reinforcing bars using the ground penetrating radar (GPR) method. A novel element of the paper is the inspection of different arrangements of reinforcement bars. Two particular problems, i.e. detection of few adjacent transverse bars and detection of a longitudinal bar located over or under transverse reinforcement, have been raised. An attention was also...
-
A Finite Element Approach for Wave Propagation in Elastic Solids
PublikacjaThis book focuses on wave propagation phenomena in elastic solids modelled by the use of the finite element method. Although the latter is a well-established and popular numerical tool used by engineers and researchers all around the word the process of modelling of wave propagation can still be a challenge. The book introduces a reader to the problem by presenting a historical background and offering a broad perspective on the...
-
Numerical Analysis of Impact of Energy Buoy Anchoring Configurations on its Motion and Efficiency
PublikacjaThis paper presents a numerical analysis of the impact of energy buoy mooring configurations on its movement on the wave and effectiveness. The method used to analyse the buoy movement modelling in six degrees of freedom was described in a paper presented at the Conference 2011. Simulations of the buoy movement in regular wave and power calculations were conducted for several configurations of anchoring systems and position of...
-
Chip suction system in circular sawing machine: empirical research and computational fluid dynamics numerical simulations
PublikacjaThe experimental analysis of the wood chip removing system during its redesigning in the existing sliding table circular saw and computational fluid dynamic (CFD) numerical simulations of the air flow process is presented in the paper. The attention was focused on the extraction hood and the bottom shelter of the actual existing system. The main aim was to perform experimental research on the pressure distribution inside the...
-
Experimental and computational study on mechanical behaviour of carpentry corner log joints
PublikacjaThis work concerns experimental and numerical research on carpentry joints used in historic wooden buildings in southeastern Poland and western Ukraine. These structures are mainly sacred buildings, and the types of corner log joints characteristic of this region are primarily saddle-notch and dovetail joints; thus, these two types of joints were analysed in this study. The modelling of historic timber structures is a complex...
-
The impact of the shape of deep drilled well screen openings on the filtration process in full saturation conditions
PublikacjaThe authors propose a supplementary method of modelling seepage flow around the deep drilled well screen. The study applies 3D numerical modelling (FEM) in order to provide an in-depth analysis of the seepage process. The analysis of filtration parameters (flow distribution q(x,t) and pressure distribution p) was conducted using the ZSoil.PC software system. The analysis indicates that the shape of perforation is of secondary importance...
-
Damaged plasticity model - seismic analysis of structure of the Petronas Twin Towers (Kuala Lumpur) in Malaysia
PublikacjaThe article presents numerical simulations for the modelling of seismic impact on the structure of Petronas Twin Towers (Kuala Lumpur) in Malaysia with application of two methods. The Response Spectrum method, in which a spectrum of the structure's responses to an earthquake's impact is generated and the Acceletogram (BETA) method, in which we generate dynamic load in the form of a diagram of the connection between acceleration...
-
Experimental and numerical investigations of ultimate strength of degradated structures
PublikacjaThe presented work investigates the corrosion influence on the structural behaviour of structural elements. Nine welded large-scale stiffened plates, and 30 standard small specimens have been subjected to the accelerated marine immersed conditions. After corrosion testing, the specimens have been accurately measured in terms of surface characteristics. The coupon specimens were furtherly subjected to tensile loading to develop...
-
A new open-source software developed for numerical simulations usingdiscrete modeling methods
PublikacjaThe purpose of this work is to present the development of an open-source software based on a discrete description of matter applied to study the behavior of geomaterials. This software uses Object Oriented Programming techniques, and its methodology design uses three different methods, which are the Discrete Element Method (DEM) [F. Donzé, S.A. Magnier, Formulation of a three-dimensional numerical model of brittle behavior, Geophys....
-
LDFEM analysis of pore water pressure development in cohesive soil due to FDP auger drilling
PublikacjaThis paper presents the preliminary modelling of FDP auger drilling in soft soil with emphasis on excess pore water pressure (EPWP) development using CEL formulation and Abaqus software suit. The EPWP generation in single points is investigated and the results of a numerical analysis are compared with the field measurements. It is found that numerical model qualitatively reflects the field measurements. However,...
-
NUMERICAL ANALYSIS OF SPECIES DIFFUSION AND METHANOL DECOMPOSITION IN THERMOCATALYTIC REACTOR BASED ON THE INTERMETALLIC PHASE OF Ni3Al FOR LOW REYNOLDS NUMBERS
PublikacjaNumerical modelling of hydrogen production by means of methanol decomposition in a thermocatalytic reactor using corrugated foil made of the Ni3Al intermetallic phase is shown in the paper. Experimental results of the flow analysis of mixtures containing helium and methanol in a thermocatalytic reactor with microchannels were used for the initial calibration of the CFD calculations (calculations based on the Computational Fluid...
-
Long-term hindcast simulation of sea level in the Baltic Sea
Dane BadawczeThe dataset contains the results of numerical modelling of sea level fluctuations over a period of 50 years (1958-2007) in the Baltic Sea. A long-term hindcast simulation was performed using a three-dimensional hydrodynamic model PM3D (Kowalewski and Kowalewska-Kalkowska, 2017), a new version of the M3D model (Kowalewski, 1997). The hydrodynamic model...
-
NUMERICAL MODEL QUALITY ASSESSMENT OF OFFSHORE WIND TURBINE SUPPORTING STRUCTURE BASED ON EXPERIMENTAL DATA
PublikacjaAs a structure degrades some changes in its dynamical behavior can be observed, and inversely, observation and evaluation of these dynamical changes of the structure can provide information of structural state of the object. Testing of the real structure, besides of being costly, can cover only limited working states. It is particularly considerable in case of hardly accessible, and randomly/severely dynamically loaded offshore...
-
Numerical Analysis of Recharge Rates and Contaminant Travel Time in Layered Unsaturated Soils
PublikacjaThis study focused on the estimation of groundwater recharge rates and travel time of conservative contaminants between ground surface and aquifer. Numerical simulations of transient water flow and solute transport were performed using the SWAP computer program for 10 layered soil profiles, composed of materials ranging from gravel to clay. In particular, sensitivity of the results to the thickness and position of weakly permeable...
-
Assessing groundwater vulnerability to pollution in the Puck region (denudation moraine upland) using vertical seepage method
PublikacjaDegradation of groundwater quality can cause a serious water supply and environmental problems. The identify of potential groundwater pollution can be determined by assessment of groundwater vulnerability method. The assessment of groundwater vulnerability to pollution was based on estimation of migration time of potential conservative contamination through the vadose zone. Area of investigation is a type of denudation moraine...
-
Rebuilding Bailey Bridge to Bridge With Bascule Span – A Case Study
PublikacjaThe structural analysis of a road foldable prefabricated steel Bailey- type bridge located over the Tuga River in Żelichowo, Poland is performed in this paper. Interesting and untypical bridge redevelopment performed made it possible to lift the middle foldable bridge span by approximately 4.0 m concerning the existing state. The paper begins with a survey of literature carried out on the investigations of foldable Bailey-type...
-
Coupled Urban Areas Inundation Model with Interaction Between Storm Water System and Surface Flow - Case Study of Sea Level Impact on Seaside Areas Flooding
PublikacjaInundations are becoming more frequent than ever. What is connected with increasing area of impervious surface in cities. This makes predicting urban flooding and its scale especially important. At the seaside we observe additional conditions such as sea level that makes accurate numerical modelling of issue even harder. With complex approach to the matter which is simultaneous calculation of storm water conduit flow and overland...
-
Junctions In Shell Structures: A Review
PublikacjaMany shell structures used in modern technology consist of regular shell parts joined together along their common boundaries. We review different theoretical, numerical, and experimental approaches to modelling, analyses and design of the compound shell structures with junctions. Several alternative forms of boundary, continuity and jump conditions at the singular midsurface curves modelling the shell junction are reviewed. We...
-
Long-term hindcast simulation of water temperature and salinity in the Baltic Sea
Dane BadawczeThe dataset contains the results of numerical modelling of water temperature and salinity over a period of 50 years (1958-2007) in the Baltic Sea. A long-term hindcast simulation was performed using a three-dimensional hydrodynamic model PM3D (Kowalewski and Kowalewska-Kalkowska, 2017), a new version of the M3D model (Kowalewski, 1997). The hydrodynamic...
-
Long-term hindcast simulation of currents in the Baltic Sea
Dane BadawczeThe dataset contains the results of numerical modelling of currents over a period of 50 years (1958-2007) in the Baltic Sea . A long-term hindcast simulation was performed using a three-dimensional hydrodynamic model PM3D (Kowalewski and Kowalewska-Kalkowska, 2017), a new version of the M3D model (Kowalewski, 1997). The hydrodynamic model was coupled...
-
Research into the Movements of Surface Water Masses in the Basins Adjacent to the Port
PublikacjaThis paper presents the results of the practical and simulation research into determining the routes of movement of small objects moving together with surface water masses in basins adjacent to the port. The results of this research were referenced against the modelling of routes of small objects in port channel basins. The results of practical research concerning the movement of small objects in basins adjacent to the port were...
-
A three-dimensional periodic beam for vibroacoustic isolation purposes
PublikacjaThis paper presents results of investigations on a three-dimensional (3-D) isotropic periodic beam. The beam can represent a vibroacoustic isolator of optimised dynamic characteristics in the case of its longitudinal, flexural and torsional behaviour. The optimisation process concerned both the widths as well as the positions of particular frequency band gaps that are present in the frequency spectrum of the beam. Since the dynamic...
-
Experimental and numerical study of thermal and electrical potential of BIPV/T collector in the form of air-cooled photovoltaic roof tile
PublikacjaAmong renewable energy sources, Building-Integrated Photovoltaic/Thermal (BIPV/T) systems are gaining increasing interest. To improve their economic competitiveness, technologies that increase their efficiency are searched for. The paper is devoted to evaluating the impact of various air-cooling configurations on the thermal and electrical performance of a photovoltaic roof tile. A numerical model of the own experimental system...
-
Experimental and numerical investigation on shell and coil storage unit with biodegradable PCM for modular thermal battery applications
PublikacjaThermal energy storage (TES) in automotive applications is currently growing in importance. TES can visibly reduce primary energy consumptions, decrease CO2 emission, and improve thermal comfort in electric as well as hybrid vehicles. However, to meet the new ambitious target (15% reduction of CO2 emissions in the new cars until 2025) it is required to use plug-in electric vehicles. For this reason, this paper focuses on the optimization...
-
Technical fabrics in costruction of large scale roofs - numerical and experimental aspects
PublikacjaDesigning and construction of textile hanging roofs is the challenging subject for engineers. This type of structure needs geometrically and very often also physically non-linear calculations. Due to different behaviour of two families of threads (warp and weft), which during deformation can change the angle between their directions, they require special constitutive modelling. Also the loading of hanging roofs is very special....
-
Numerical Analysis of an Impact of Planned Location of Sewage Discharge on Natura 2000 Areas – The Dead Vistula Region Case Study
PublikacjaThis article presents results of an analysis of impact of a designed discharge of contaminated water into the Dead Vistula (Wisła Martwa) in the region of the Isthmus (Przesmyk) with the aim of determination of a possible effect of the pollution onto protected areas of Natura 2000 (bird habitats and sites, especially the Bird Paradise – Ptasi Raj) nature reserve. The analysis was conducted on the basis of the two-dimensional modelling...
-
THE EFFECT OF NOTCH DEPTH ON CTOD VALUES IN FRACTURE TESTS OF STRUCTURAL STEEL ELEMENTS
PublikacjaIn elements of steel structures working at low temperatures, there is a risk of appearance of brittle fracture. This risk is reduced through the use of certified materials having guaranteed strength at a given temperature. A method which is most frequently used to determine brittle fracture toughness is the Charpy impact test, preformed for a given temperature. For offshore structures intended to work in the arctic climat e, the...
-
Large deformation finite element analysis of undrained pile installation
PublikacjaIn this paper, a numerical undrained analysis of pile jacking into the subsoil using Abaqus software suit has been presented. Two different approaches, including traditional Finite Element Method (FEM) and Arbitrary Lagrangian–Eulerian (ALE) formulation, were tested. In the first method, the soil was modelled as a two-phase medium and effective stress analysis was performed. In the second one (ALE), a single-phase medium was assumed...
-
Neural Networks, Support Vector Machine and Genetic Algorithms for Autonomous Underwater Robot Support
PublikacjaIn this paper, artificial neural networks, a classification technique called support vector machine and meta-heuristics genetic algorithm have been considered for development in autonomous underwater robots. Artificial neural networks have been used for seabed modelling as well as support vector machine has been applied for the obstacles classification to avoid some collision problems. Moreover, genetic algorithm has been applied...
-
Viscoplastic damage analysis of structures subjected to impact loading. Plate and shell structures. - Ł. Pyrzowski.
PublikacjaThe work presents the investigation in the response of plate-shell structures subjected to impact loading (gas mixture explosions). This phenomenon is studied in the context of its mechanical aspects, mainly the ductile fracture prediction. The work starts with the literature review and the description of theories, which are nowadays the most popular in the damage and failure modelling. After selecting the theoretical models and...
-
Turbulence models impact on the flow and thermal analyses of jet impingement
PublikacjaAccurate numerical reconstruction of heat and mass transfer processes in particular applications, such a jet impingement, is difficult to obtain even with the use of modern computational methods. In the proposed paper, the flow and thermal phenomena occurring during single minijet impingement on the flat, concave and convex, heated surfaces were considered. Problem of impingement on non-flat surface, still not common and purely...
-
Pounding between Inelastic Three-Storey Buildings under Seismic Excitations
PublikacjaStructural interactions between adjacent, insufficiently separated buildings have been repeatedly observed during damaging ground motions. This phenomenon, known as the structural pounding, may result in substantial damage or even total collapse of structures. The aim of the present paper is to show the results of the nonlinear numerical analysis focused on pounding between inelastic three-storey buildings under seismic excitations....
-
Simulations of hydro-fracking in rock mass at meso-scale using fully coupled DEM/CFD approach
PublikacjaThe paper deals with two-dimensional (2D) numerical modelling of hydro-fracking (hydraulic fracturing) in rocks at the meso-scale. A numerical model was developed to characterize the properties of fluid-driven fractures in rocks by combining the discrete element method (DEM) with computational fluid dynamics (CFD). The mechanical behaviour of the rock matrix was simulated with DEM and the behaviour of the fracturing fluid flow...
-
Viscous versus electromagnetic damping – amplification in a neighbourhood of a mechanism singular position
PublikacjaIn the paper, damping of vibrations are considered and compared in a mechanical and in a electromechanical system. In the system, a continuous beam is considered as the main vibrating element. The compared dissipations methods are based on: viscous dampers and DC generators. To increase the possible damping effectiveness, velocity amplification is proposed, i.e., a mechanism is introduced between the beam and the damping element....
-
Influence of anisotropic stiffness in numerical analyses of tunneling and excavation problems in stiff soils
PublikacjaIn the stiff overconsolidated soil deposits anisotropy influences small and intermediate strain stiffness and hence it has important impact on the results of discplacement preditcions in soil-structure modelling. The authors developed a cross-anisotropic soil model which combines both stress dependent and micro-structural anisotropy. The model is based on the anisotropic hyperelastic kernel for small strain stiffness. Reference...
-
Modelling and simulations in time-fractional electrodynamics based on control engineering methods
PublikacjaIn this paper, control engineering methods are presented with regard to modelling and simulations of signal propagation in time-fractional (TF) electrodynamics. That is, signal propagation is simulated in electromagnetic media described by Maxwell’s equations with fractional-order constitutive relations in the time domain. We demonstrate that such equations in TF electrodynamics can be considered as a continuous-time system of...
-
MODELLING OF TRANSIENT FLOW IN STORM SEWERS
PublikacjaThe paper focuses on the assessment of second-order explicit numerical scheme for unsteady flows in sewers. In order to simulate the pressurized flow the 'Preissmann slot' concept is implemented. For simulation of the transcritical flow the original and improved McCormack scheme is used. The calculated results are compared with numerical solutions and laboratory measurements published in the technical literature. Moreover, the...
-
Spectral Finite Element Method in Condition Monitoring and Damage Detection
PublikacjaIt is well known that the dynamic behaviour of engineering structures may carry very important and crucial information that can be further used for the assessment of their condition as well as detection of any damage induced. The current interest in monitoring techniques based on the propagation of guided elastic waves requires that numerical techniques used for modelling the phenomena associated must shift into the realm of high...
-
Comparative study of a combined heat and power plant retrofitted by CO2 capture during the combustion of syngas from sewage sludge gasification versus zero-emission combustion of hydrogen produced using renewables
PublikacjaWith ecological requirements aimed at limiting the production of CO2, it is necessary to produce all, or most of the energy from RES. During the transformation process, ecological and highly efficient combustion power plants will be needed. The classic cycle of combined heat and power (CCGT) with green improvements will continue to be one of the most suitable technologies for this task. This article presents the modernization of...