Filtry
wszystkich: 1759
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: COMBUSTION ENGINE TESTING
-
Analysis of balancing of six-cylinder in-line two-stroke internal combustion engines = Analiza wyrównoważenia silników rzędowych dwusuwowych sześciocylindrowych
PublikacjaW pracy wyprowadzono proste zależności opisujące przebieg momentu od sił bezwładności pierwszego i drugiego rzędu dla wszystkich 60 wariantów wałów korbowych w silniku 6-cylindrowym 2-suwowym rzędowym. Dokonano analizy i porównania poszczególnych wariantów z punktu widzenia momentów wypadkowych od sił bezwładności pierwszego i drugiego rzędu. Porównania dokonano dla dwóch wartości parametru mechanizmu korbowego 0,3 i 0,5.
-
Heat transfer to car engine cooling system - influence of coolant flow through engine block
PublikacjaW artykule przedstawiono wyniki badań doświadczalnych nad wpływem nastawianej wydajności pompy cieczy na strumień odbieranego ciepła w silniku spalinowym. Wykorzystano hamownię silnikową z silnikiem o zapłonie iskrowym o objętości skokowej 1.8 dm^3. Przyjęto obciążenia silnika oporami ruchu samochodu na biegu bezpośrednim.
-
Systematic investigation on combustion characteristics and emission-reduction mechanism of potentially toxic elements in biomass- and biochar-coal co-combustion systems
Publikacja -
A review on application of artificial neural network (ANN) for performance and emission characteristics of diesel engine fueled with biodiesel-based fuels
PublikacjaBiodiesel has been emerging as a potential and promising biofuel for the strategy of reducing toxic emissions and improving engine performance. Computational methods aiming to offer numerical solutions were inevitable as a study methodology which was sometimes considered the only practical method. Artificial neural networks (ANN) were data-processing systems, which were used to tackle many issues in engineering and science, especially...
-
Numerical investigations of the engine cooling system in a small power vesel pod propulsion system
PublikacjaThe development of electronics and electrotechnology enabled to put electric motors of the alternating current in the pod and to use them for the main drive of ships. A lot of heat which must be picked up from the system is a problem which is turning up at applying the system of this type. Many big ships lately contended with these problems. Building the small propeller for the boat powered with solar power we decided to check...
-
Self-Testing of Analog Parts Terminated by ADCs Based on Multiple Sampling of Time Responses
PublikacjaA new approach for self-testing of analog parts terminated by analog-to-digital converters in mixed-signal electronic microsystems controlled by microcontrollers is presented. It is based upon a new fault diagnosis method using a transformation of the set of voltage samples of the time response of a tested analog part to a square impulse into localization curves placed in a multidimensional measurement space. The method can be used...
-
Novel MNZ-type microwave sensor for testing magnetodielectric materials
PublikacjaA novel microwave sensor with the mu-near-zero (MNZ) property is proposed for testing magnetodielectric material at 4.5 GHz. The sensor has a double-layer design consisting of a microstrip line and a metal strip with vias on layers 1 and 2, respectively. The proposed sensor can detect a unit change in relative permittivity and relative permeability with a difference in the operating frequency of 45 MHz and 78 MHz, respectively....
-
Challenges in operating and testing loop heat pipes in 500–700 K temperature ranges
PublikacjaThe potential applications of loop heat pipes (LHPs) are the nuclear power space systems, fuel cell thermal management systems, waste heat recovery systems, medium temperature electronic systems, medium temperature military systems, among others. Such applications usually operate in temperature ranges between 500–700 K, hence it is necessary to develop an LHP system that will meet this requirement. Such a thermal management device...
-
Situational Awareness Network for the Electric Power System: the Architecture and Testing Metrics
PublikacjaThe contemporary electric power system is highly dependent on Information and Communication Technologies which results in its exposure to new types of threats, such as Advanced Persistent Threats (APT) or Distributed-Denial-of-Service (DDoS) attacks. The most exposed components are Industrial Control Systems in substations and Distributed Control Systems in power plants. Therefore, it is necessary to ensure the cyber security of...
-
It applications for the remote testing of hearing.
PublikacjaTelemedycyna odgrywa coraz wiekszą rolę w diagnostyce i leczeniu osób z ubytkami słuchu. Jest to związane m.in. ze specyfiką badań audiometrycznych. Postęp technologiczny w dziedzinie aparatów słuchowych i implantów ślimakowych wymusza nowe metody diagnozy w audiologii, jak również w praktyce otolaryngologicznej. Serwis ''Telezdrowie'', w którym zaimplementowano liczne testy przesiewowe jest przykładem prowadzenia diagnostyki w...
-
Testing aggressive TCP configurations
PublikacjaNa podstawie badań symulacyjnych i analizy potwierdzono strukturalne podobieństwo gier wywiązujących się przy autonomicznym ustawianiu parametrów sterowania przeciążeniem w protokole TCP do wieloosobowego Dylematu Więźnia. Przeprowadzono badania przepływności połączeń sieciowych w obecności wielu wąskich gardeł dla kilku topologii sieciowych. W wyniku badań wskazano scenariusze ruchowe szczególnie podatne na agresywne zachowania...
-
FATIGUE TESTING MACHINES AND APPARATUS
Publikacja -
Outboard valve material testing
PublikacjaWykonano analizę przyczyn uszkodzenia korozyjnego zaworu zaburtowego. Sformułowano wnioski.
-
Algorithms for testing security in graphs
PublikacjaIn this paper we propose new algorithmic methods giving with the high probability the correct answer to the decision problem of security in graphs. For a given graph G and a subset S of a vertex set of G we have to decide whether S is secure, i.e. every subset X of S fulfils the condition: |N[X] \cap S| >= |N[X] \ S|, where N[X] is a closed neighbourhood of X in graph G. We constructed a polynomial time property pseudotester based...
-
Conformance testing of parallel languages
PublikacjaPrzedstawiono propozycję formalizacji opisu procesu generacji, wykonania ioceny testów zgodności dla języków i bibliotek programowania równoległego, wzakresie zgodności funkcjonalnej i wydajnościowej. Przykłady ilustrujące proponowany formalizm wykorzystują platformę programowania Athapascan.
-
Mechanical-Level Hardware-In-The-Loop and Simulation in Validation Testing of Prototype Tower Crane Drives
PublikacjaIn this paper, the static and dynamic simulations, and mechanical-level Hardware-In-the-Loop (MHIL) laboratory testing methodology of prototype drive systems with energy-saving permanent-magnet electric motors, intended for use in modern construction cranes is proposed and described. This research was aimed at designing and constructing a new type of tower crane by Krupiński Cranes Company. The described research stage was necessary...
-
A model, design, and implementation of an efficient multithreaded workflow execution engine with data streaming, caching, and storage constraints
PublikacjaThe paper proposes a model, design, and implementation of an efficient multithreaded engine for execution of distributed service-based workflows with data streaming defined on a per task basis. The implementation takes into account capacity constraints of the servers on which services are installed and the workflow data footprint if needed. Furthermore, it also considers storage space of the workflow execution engine and its cost....
-
Modern Platform for Parallel Algorithms Testing: Java on Intel Xeon Phi
PublikacjaParallel algorithms are popular method of increasing system performance. Apart from showing their properties using asymptotic analysis, proof-of-concept implementation and practical experiments are often required. In order to speed up the development and provide simple and easily accessible testing environment that enables execution of reliable experiments, the paper proposes a platform with multi-core computational accelerator:...
-
Machine learning approach to packaging compatibility testing in the new product development process
PublikacjaThe paper compares the effectiveness of selected machine learning methods as modelling tools supporting the selection of a packaging type in new product development process. The main goal of the developed model is to reduce the risk of failure in compatibility tests which are preformed to ensure safety, durability, and efficacy of the finished product for the entire period of its shelf life and consumer use. This kind of testing...
-
A testing method of analog parts of mixed-signal electronic systems equipped with the IEEE1149.1 test bus
PublikacjaA new solution of the JTAG BIST for testing analog circuits in mixed-signal electronic microsystems controlled by microcontrollers and equipped with the IEEE1149.1 bus is presented. It is based on a new fault diagnosis method in which an analog circuit is stimulated by a buffered signal from the TMS line, and the time response of the circuit to this signal is sampled by the ADC equipped with the JTAG. The method can be used for...
-
COMBUSTION EXPLOSION AND SHOCK WAVES
Czasopisma -
Journal of the Korean Society of Combustion
Czasopisma -
Applications in Energy and Combustion Science
Czasopisma -
Nondestructive Testing of the Miter Gates Using Various Measurement Methods
PublikacjaWhen any problems related to civil engineering structures appear, identifying the issue through the usage of only one measuring method is difficult. Therefore, comprehensive tests are required to identify the main source. The strains and displacement measurements, as well as modal identification, are widely used in the nondestructive testing of structures. However, measurements are usually carried out at several points and confirm...
-
Diagnostic Analysis of Exhaust Gas with A Quick-Changing Temperature from a Marine Diesel Engine Part II / Two Factor Analysis
PublikacjaThe article presents a continuation of research carried out to determine the effect of input parameters (changes in engine structure parameters) on selected output parameters (diagnostic measures), based on quickly changing exhaust gas temperature. A method of determining the simultaneous influence of two input factors (the structure parameter and the engine load) on one output factor was presented, as well as an evaluation...
-
Conversion of a diesel engine bus into a trolleybus
PublikacjaPrzedsiębiorstwo Komunikacji Trolejbusowej w Gdyni od 2004 roku we własnym zakresie buduje trolejbusy w oparciu o nadwozia używanych autobusów. W monografii przedstawiono przyczyny rozpoczęcia tego przedsięwzięcie, jego przebieg oraz techniczny budowy trolejbusu w oparciu o nadwozie autobusowe.
-
Experimental verification of a new method of loop resistance testing in low voltage systems with residual current devices
PublikacjaA periodical verification of the effectiveness of protection against electric shock shall be performed in low voltage systems. The scope of this verification includes loop impedance/resistance testing. If a residual current device is installed in a tested circuit, this testing is problematic. A residual current device trips out during the test, because of the high value of measurement current. This precludes the execution of the...
-
Low sulphur coal combustion - Optimisation of boiler tunings.
PublikacjaBadaniami w ramach projektu objęto przede wszystkim kotły parowe oraz układy wspomagające, takie jak: podajniki węgla, młyny, wentylatory, instalacje oczyszczania spalin. Badania eksperymentalne przeprowadzono na obiektach Elektrociepłowni Kraków, natomiast obliczenia numeryczne zostały wykonane przez Politechnikę Wrocławska we współpracy z firmą R&D EDF. Sformułowano szereg konkretnych wytycznych do przeprowadzenia niezbędnych...
-
Synthesis of Multiwalled Carbon Nanotubes by Catalytic Combustion of Polypropylene
Publikacja -
Impedance Spectra of RC Model as a Result of Testing Pulse Excitation Measurement Method Dataset
PublikacjaThe dataset titled Impedance spectra of RC model as a result of testing pulse excitation measurement method contains the impedance spectrum of an exemplary test RC model obtained using pulse excitation. The dataset allows presentation of the accuracy of the impedance spectroscopy measuring instrument, which uses the pulse excitation method to shorten the time of the whole spectrum acquisition.
-
The Impact of Material Selection on Durability of Exhaust Valve Faces of a Ship Engine – A Case Study
Publikacjawo alloys were used in order to extend the service life of marine engine exhaust valve head. Layers of cobalt base alloys were made of the powders with with chemical composition as follow: the layer marked L12; C-1,55%; Si-1,21%; Cr-29,7%; W-9%; Ni-2%; Mo<0,01%; Fe-1,7%; Co-54,83% and the layer marked N; C-1,45%; Co-38,9%; Cr-24,13%; Ni-10,43%; W-8,75%; Fe-7,64%; Mo-7,56%; Si-2,59%. Base metal was valve steel after heat treatment....
-
An idea of an approach to self-testing of mixed signal systems based on a quadratic function stimulation
PublikacjaA new approach to self-testing of the analog parts of mixed-signal electronic systems controlled by microcontrollers equipped with an ADC and a DAC is presented. It is based on a BIST and a new fault diagnosis method. A novelty is the use of the DAC as a component of the BIST, allowing to generate a stimulating signal with a quadratic function shape. It contributes to a better extraction of information about the state of the circuit...
-
Load Testing of GFRP Composite U-Shape Footbridge
PublikacjaThe paper presents the scope of load tests carried out on an innovative shell composite footbridge. The tested footbridge was manufactured in one production cycle and has no components made from materials other than GFRP laminates and PET foam. The load tests, performed on a 14-m long structure, were the final stage of a research program in the Fobridge project carried out in cooperation with: Gdańsk University of Technology (leader),...
-
Thermographic images during testing measuring instrument boards
Dane BadawczeThe dataset presents thermografic images acquired during testing the prototype of measuring instrument for resistiometric corrosion monitoring. The testing was performed in the room temperature. VIGOcam v50 thermal imaging camera (VIGO System S.A., Ozarow Mazowiecki, Poland) was used for taking the pictures. These pictures were used as preliminary tests...
-
Assesment of operation of ship main diesel engine using the theory of semi-markovian and markov processes.
PublikacjaTo precisely determine the task it is necessary to specify also its duration time, apart from conditions in which it will be realized. When considering propulsion engine, i.e. the main element of ship propulsion system, especially important becomes not only the problem which amount of energy could be at one's disposal but also within which time interval it could be delivered. Therefore apart from applying the commonly used reliability...
-
DIAGNOSTIC INFORMATION ANALYSIS OF QUICKLY CHANGING TEMPERATURE OF EXHAUST GAS FROM MARINE DIESEL ENGINE PART I SINGLE FACTOR ANALYSIS
PublikacjaIn this paper, attention was paid to the problem of low controllability of marine medium- and high-speed engines during operation, which significantly limits the parametric diagnosis. The measurement of quickly changing temperature of engine exhaust gas was proposed, the courses of which can be a source of diagnostic information. The F statistic of the Fisher-Snedecor distribution was chosen as a statistical tool. Laboratory tests...
-
Marek Blok dr hab. inż.
OsobyMarek Blok w 1994 roku ukończył studia na kierunku Telekomunikacja wydziału Elektroniki Politechniki Gdańskiej i uzyskał tytuł mgra inżyniera. Doktorat w zakresie telekomunikacji uzyskał w 2003 roku na Wydziale Elektroniki, Telekomunikacji i Informatyki Politechniki Gdańskiej. W 2017 roku uzyskał stopień naukowy dra habilitowanego w dyscyplinie telekomunikacja. Jego zainteresowania badawcze ukierunkowane są na telekomunikacyjne...
-
Novel Cast Polyurethanes Obtained by Using Reactive Phosphorus-Containing Polyol: Synthesis, Thermal Analysis and Combustion Behaviors
PublikacjaPhosphorus-containing polyol applications in polyurethane synthesis can prevent volatilization of flame retardants and their migration on the surface of a material. In this work, novel cast polyurethanes were prepared by a one-step method with the use of different amounts of phosphorus-containing polyol, 4,4′–diphenylmethane diisocyanate and 1,4-butanediol. The chemical structure, thermal, physicochemical and mechanical properties...
-
Genetic Testing and Molecular Biomarkers
Czasopisma -
Papers in Language Testing and Assessment
Czasopisma -
International Journal of Language Testing
Czasopisma -
RUSSIAN JOURNAL OF NONDESTRUCTIVE TESTING
Czasopisma -
SOFTWARE TESTING VERIFICATION & RELIABILITY
Czasopisma -
Selected aspects of determining the reliability of the pump subsystems with redundancy, used in main engine auxiliary systems
PublikacjaThe rules of classification societies require the use of redundancy in the systems essential for the safety of the ship. Duplication of pumps in the main engine auxiliary systems like cooling water system, lubricating oil system, fuel oil system is a good example here. Therefore, in the author's opinion, some attention should be paid to this issue. Two important questions arise here. Does duplication of pumps in marine systems...
-
Experimental database of 3D lattice structure scaffolds testing
Dane BadawczeDataset contains results of validation (experimental testing) of 3D lattice scaffolds proposed in the paper "Mathematical approach to design 3D scaffolds for the 3D printable bone implant". There are presented three series of experimental testing for each of seven tested scaffolds:
-
APPLICATION OF INFRARED THERMOGRAPHY TO NON-CONTACT TESTING OF AD/DC POWER SUPPLY
PublikacjaTesting of AC/DC power supplies using the thermography was carried out in order to assess their assembly and operation correctness before launching them on the market. The investigation was carried out for 17 AC/DC power supplies which passed the standard tests (measurements of their basic parameters and characteristics). The investigation consisted of two steps. In the first step the dispersion of temperature on power supply boards...
-
Computer modeling and testing of structural metamaterials
Publikacja -
Testing of the Superconducting Magnets Frequency Characteristics
PublikacjaPrzedstawiono zagadnienia związane z opracowaniem systemu do wyznaczania impedancji uzwojeń magnesów nadprzewodzących w funkcji częstotliwości. Omówiono strukturę sprzętową systemu, oprogramowanie oraz sposób wyznaczania parametrów badanego uzwojenia. Pokazano przykładowe wyniki uzyskane przy użyciu omawianego systemu w GSI w Darmstadt.
-
Testing the usability of decisional DNA in robotics
PublikacjaW pracy poddano dyskusji i nalizie obszary mozliwych zastowac reprezentacji wiedzy zwanej Decisional DNA w zagadnieniach zwiazanych z robotyka.
-
Testing and tuning PLC application programs
PublikacjaWe wstępie zawarto kilka uwag autora dotyczących pilnej potrzeby wdrażania na Wydziale Mechanicznym idei mechatronicznego kształcenia. Przedstawiono przegląd sposobów monitorowania i testowania programów aplikacyjnych PLC podczas budowania lub modernizacji systemów sterowania. Przedyskutowano zakres zastosowań oraz ograniczenia poszczególnych sposobów. Opisano przykład zastosowania zbudowanego stanowiska do eksperymentalnych testów...