Filtry
wszystkich: 310
Wyniki wyszukiwania dla: 2d/3d surface texture
-
Comparison of road and laboratory measurements of tyre/road noise
PublikacjaTyre/road noise is one of the major environmental problems related to road traffic. There are several measuring methods of tyre/road noise that may be carried out on the road (for example Coast-down and Close Proximity Method) or in the laboratory (Drum Method). Road measurements are preferred for evaluations of pavement properties while laboratory methods are mostly used to evaluate tyres. One of the biggest problems associated...
-
The inverse problem in a hyperbolic section radial compressor.
PublikacjaNa przykładzie wirnika sprężarki porównano wyniki rozwiązania zadania odwrotnego w ramach modelu 2D prowadzącego do kształtu wirnika, z zadaniem prostym, w ramach modelu 3D, dla skonstruowanego wirnika na bazie modelu 2D.Zasadniczym celem było uzyskanie równomiernych (bez oderwań) pól parametrów w obrębie wirnika sprężarki. Pokazano jak zmiana obrysu wirnika, z klasycznego kształtu stożkowego na hiperboliczny, wpłynąć może na...
-
Roughness evaluation of turned composite surfaces by analysis of the shape of Autocorrelation Function
PublikacjaIn this paper, the application of an Autocorrelation Function for the characterisation of surface topography was validated. The roughness evaluation of turned composite surfaces was supported by sophisticated studies of the Autocorrelation Function properties, considering especially the shape of the function. Details were measured with the optical method. The selection of the surface roughness evaluation procedures was carried...
-
The electrochemical studies of CB-PLA electrode after surface activation by proteinase K digestion
Dane BadawczeThe dataset contains the electrochemical studies performed to evaluate surface activation of the CB-PLA 3D printed electrodes by enzymatic hydrolysis in a solution containing proteinase K (72h digestion period). Different enzyme concentrations were evaluated: 0.2, 0.4, 0.6 and 0.8 mg/ml. The studies were performed before surface activation, during and...
-
Using GPUs for Parallel Stencil Computations in Relativistic Hydrodynamic Simulation
PublikacjaThis paper explores the possibilities of using a GPU for complex 3D finite difference computation. We propose a new approach to this topic using surface memory and compare it with 3D stencil computations carried out via shared memory, which is currently considered to be the best approach. The case study was performed for the extensive computation of collisions between heavy nuclei in terms of relativistic hydrodynamics.
-
Shear fracture of longitudinally reinforced concrete beams under bending using Digital Image Correlation and FE simulations with concrete micro-structure based on X-ray micro-computed tomography images
PublikacjaThe paper presents experimental and numerical investigations of the shear fracture in rectangular concrete beams longitudinally reinforced with steel or basalt bar under quasi-static three point bending. Shear fracture process zone formation and development on the surface of beams was investigated by Digital Image Correlation (DIC) whereas thorough analyses of 3D material micro-structure, air voids, width and curvature of shear...
-
CAD Introduction (2023/24)
Kursy OnlineThe course aim is to demonstrate the application of Computer Aided Design in preparation of architectural drawings and project presentations. No previous CAD experience is necessary. Using hands-on exercises, students explore how to create project presentations using 2D drawings and 3D models created in AutoDesk AutoCAD and other programs.
-
A new concept of PWM duty cycle computation using the Barycentric Coordinates in a Three-Dimensional voltage vectors arrangement
PublikacjaThe paper presents a novel approach to the Pulse Width Modulation (PWM) duty cycle computing for complex or irregular voltage vector arrangements in the two (2D) and three–dimensional (3D) Cartesian coordinate systems. The given vectors arrangement can be built using at least three vectors or collections with variable number of involved vectors (i.e. virtual vectors). Graphically, these vectors form a convex figure, in particular,...
-
The cyclic voltammetry studies of CB-PLA electrode after surface activation by electrolysis in 1M NaOH
Dane BadawczeThe dataset contains the electrochemical studies performed for surface activation of the CB-PLA 3D printed electrodes by electrolysis in 1M NaOH solution. The studies were performed after treatment at an anodic overpotential of 1V, found to be optimal for surface activation. The measurements were carried out with cyclic voltammetry (CV) under different...
-
Modelling method for a class of distributed-lumped parameter systems
PublikacjaThe paper presents an alternative approach for modelling and order reduction of continuous system. The proposed methodology combines application of two methods: the modal decomposition method and the rigid finite element method. The given continuous structure is divided into 1D continuous substructures. For each 1D substructure modal decomposition and reduction procedure is applied. Interactions between substructures are described...
-
Weak localization competes with the quantum oscillations in a natural electronic superlattice: The case of Na1.5(PO2)4(WO3)20
PublikacjaWe report an investigation of the combined structural and electronic properties of the bronze Na1.5(PO2)4(WO3)20. Its low-dimensional structure and possible large reconstruction of the Fermi surface due to charge density wave instability make this bulk material a natural superlattice with a reduced number of carriers and Fermi energy. Signatures of multilayered two-dimensional (2D) electron weak localization are consequently reported,...
-
Genetic programming extension to APF-based monocular human body pose estimation
PublikacjaNew method of the human body pose estimation based on a single camera 2D observation is presented, aimed at smart surveillance related video analysis and action recognition. It employs 3D model of the human body, and genetic algorithm combined with annealed particle filter for searching the global optimum of model state, best matching the object's 2D observation. Additionally, new motion cost metric is employed, considering current...
-
Chemical Pressure Tuning Magnetism from Pyrochlore to Triangular Lattices
PublikacjaGeometrically frustrated lattices combined with magnetism usually host quantum fluctuations that suppress magnetic orders and generate highly entangled ground states. Three-dimensionally (3D) frustrated magnets generally exist in the diamond and pyrochlore lattices, while two-dimensionally (2D) frustrated geometries contain Kagomé, triangular, and honeycomb lattices. In this work, we reported using chemical pressure to tune the magnetism...
-
Morphology changes in Fe-Cr porous alloys upon high-temperature oxidation quantified by X-ray tomographic microscopy
PublikacjaThe effect of high-temperature oxidation at 850 C (10 h, 30 h, 100 h) and 900 C (10 h) on porous (30 % porosity) ferritic stainless steel (Fe22Cr) has been investigated using synchrotron tomographic microscopy, which allowed for visualisation, separation and quantitative analysis of the metallic core, closed pores, open pores and oxide scale phase. The same regions within the samples were investigated before and after oxidation...
-
Analysis of the Surface Stereometry of Alloyed Austenitic Steel after Fibre Laser Cutting using Confocal Microscopy
PublikacjaThe paper extends the concept of cut edge quality and examines the fibre laser cutting process. A Prima Power Platino Fiber Evo device with a reference speed (RS) of 3500 mm/min was used for laser cutting. In order to analyse the influence of the laser cutting speed on the cut edge quality of X5CrNi18-10 stainless steel sheets, macroscopic studies were conducted on a stereoscopic microscope and surface stereometry on a confocal...
-
Trawl-Door Shape Optimization with 3D CFD Models and Local Surrogates
PublikacjaDesign and optimization of trawl-doors are key factors in minimizing the fuel consumption of fishing vessels. This paper discusses optimization of the trawl-door shapes using high-fidelity 3D computational fluid dynamic (CFD) models. The accurate 3D CFD models are computationally expensive and, therefore, the direct use of traditional optimization algorithms, which often require a large number of evaluations, may be prohibitive....
-
Dynamic effect of the vehicle passing under lightweight footbridge.
PublikacjaThe paper describes a numerical study of dynamic response of cable-stayed steel footbridge for a big lorry passing underneath. The footbridge is an existing object crossing Wolska street in Warsaw. The structural model of footbridge was verified by dynamic test loading. A numerical study of a vehicle passing under footbridge is presented. 2D and 3D incompressible flow fields are modeled using sliding mesh in transient CFD computation....
-
Numerical investigations on early indicators of fracture in concrete at meso-scale.
PublikacjaFracture is a major reason of the global failure of concretes. The understanding of fracture is important to ensure the safety of structures and to optimize the material behaviour. In particular an early prediction possibility of fracture in concretes is of major importance. In this paper, concrete fracture under bending was numerically analysed using the Discrete Element Method (DEM). The real mesoscopic structure of a concrete...
-
Solvothermal growth of {0 0 1} exposed anatase nanosheets and their ability to mineralize organic pollutants. The effect of alcohol type and content on the nucleation and growth of TiO2 nanostructures
PublikacjaHerein, the series of {0 0 1} exposed anatase nanosheets from HF-assisted solvothermal growth synthesis were obtained. The two-dimensional TiO2 were characterized, including both bulk (XRD, DR-UV–Vis, Mott-Schottky) and surface characteristics (N2 sorption, XPS, SEM) with experimental results compiled with Density Functional Theory (DFT) calculations. The effect of alcohol amount and type was studied, demonstrating the crucial...
-
Wizyjny system monitoringu stanu nakładek stykowych odbieraków prądu
PublikacjaEksploatowane do niedawna w Polsce nakładki pantografów kolejowych były wykonywane w postaci styków miedzianych. Na początku 2011 r. przeprowadzono kompleksową zmianę typu nakładek stykowych, stosowanych przez operatorów korzystających z infrastruktury PKP PLK S.A., z miedzianych na metalizowane węglowe. Wraz z wprowadzeniem nakładek węglowych istnieje potrzeba opracowania nowych metod diagnostyki tego istotnego elementu toru zasilania...
-
Long-Term Impact of Wind Erosion on the Particle Size Distribution of Soils in the Eastern Part of the European Union
PublikacjaWind erosion is the leading cause of soil degradation and air pollution in many regionsof the world. As wind erosion is controlled by climatic factors, research on this phenomenon isurgently needed in soil and land management in order to better adapt to climate change. In thispaper, the impact of wind erosion on the soil surface in relation to particle size distribution wasinvestigated. Changes in percentage of sand, silt and...
-
Partial PLA composite surface activation by femtosecond laser ablation
Dane BadawczeThe dataset contains the studies on electrochemical activity of PLA composite (commercially available CB-PLA Protopasta), which was 3D printed in a form of 1x1cm electrodes. The electrodes were submitted to femtosecond laser ablation, etching a certain % of the electrochemically-exposed electrode size. The % value is in the name of each file. The goal...
-
The XPS studies of the CB-PLA electrodes after different surface treatments (chemical, electrochemical, enzymatic)
Dane BadawczeThe dataset contains the Xray Photoelectron Spectroscopy results of the studies performed under different conditions of surface activation of the CB-PLA 3D printed electrodes. The activation was performed by hydrolysis in different solvents (DMF, 1M HCl, 1M NaOH), electrolysis in 1M NaOH, enzymatic treatment in polymerase or simultaneous electrolysis...
-
Analysis of the bulk solid flow during gravitational silo emptying using X-ray and ECT tomography
PublikacjaW pracy przedstawiono wyniki pomiarów zmian koncentracji piasku bezkohezyjnego zachodzących w prostokątnym modelu silosu opróżnianym grawitacyjnie. Pomiary wykonano z zastosowaniem kontynualnego promieniowania rentgenowskiego oraz z użyciem tomografii pojemnościowej. Badania wykonano dla zróżnicowanego zagęszczenia początkowego piasku oraz różnego stopnia szorstkości ścian. Szczególny nacisk położono na zachowanie sie materiału...
-
EXPERIMENTAL AND NUMERICAL INVESTIGATIONS OF CONCRETE BEHAVIOUR AT MESO-LEVEL DURING QUASI-STATIC SPLITTING TENSION
PublikacjaThe paper describes experimental and numerical results of quasi-static splitting tensile tests on concrete specimens at meso-scale level. The loading strip was made of plywood or steel. Fracture in concrete was detected at the aggregate level by means of three non-destructive methods: 3D x-ray micro-computed tomography, 2D scanning electron microscope and manual 2D digital microscope. The discrete element method was used to directly...
-
Further development of the poroelastic road surface within the new Polish project SEPOR
PublikacjaRoad surfaces have a direct impact on noise generated by rolling tyres, the main and dominant source of noise of moving vehicles. Road surface texture, porosity and stiffness/elasticity govern the pavement contribution to tyre/road noise the most. An experimental PoroElastic Road Surface (PERS) is a wearing course with a high content of interconnected voids (pores) and with an elastic behavior due to the use of small particles...
-
Heat exchange enhancement of jet impingement cooling with the novel humped-cone heat sink
PublikacjaJet impingement cooling technology is applicable to control temperature of devices, where very high heat flux is generated within a small area. This paper is about the improvement of the jet impingement cooling efficiency by the heat sink geometry modification. Two reference cases were sourced from the literature – flat heat sink and modified one with cone in the jet stagnation region. Such a change improves cooling capability...
-
Optimization of the System for Determining the Volume of Tissue Needed for Breast Reconstruction
PublikacjaThis article presents techniques for reconstructing surfaces and volume calculations using a point cloud generated from 3D imaging. The main objective of this article was to optimize the voxel size for the most accurate representation of the surface of the female breast. We experimented with different methods for determining volume using images from the Intel D435i camera. In addition, we designed application and measurement station...
-
3D-Breast System for Determining the Volume of Tissue Needed for Breast Reconstruction
Publikacja3D imaging systems can be used to effectively determine breast volumes for surgical applications. This article presents methods for surface reconstruction and volume determination based on the point cloud created by 3D imaging. Such a system would be used to accurately estimate breast volume in patients classified for breast reconstruction surgery at plastic surgery centers. To develop such a system, various methods of determining...
-
Long-distance quantum communication over noisy networks without long-time quantum memory
PublikacjaThe problem of sharing entanglement over large distances is crucial for implementations of quantum cryptography. A possible scheme for long-distance entanglement sharing and quantum communication exploits networks whose nodes share Einstein-Podolsky-Rosen (EPR) pairs. In Perseguers et al. [Phys. Rev. A 78, 062324 (2008)] the authors put forward an important isomorphism between storing quantum information in a dimension D and transmission...
-
Fluorine ions in photocatalysts’ synthesis: an obstacle or an ally? The investigation of photocatalysts in Ti-O-F system
PublikacjaTitanium(IV) oxide (TiO2) is one of the most promising photocatalysts, which is expected to be applied in the photocatalytic degradation of xenobiotics. For sustainable development and green chemistry approach recently, much effort has been paid to enhance TiO2 photocatalytic activity in UV-vis light by modifying its structure. The photocatalytic process’s complexity cannot be simply described as electron-hole pairs generations...
-
Wear estimation of current collector contact strips by analysis of a 3D scanning results
PublikacjaThe technical condition of current collector contact strips is very important when operational reliability of railway transportation is considered. The authors proposed a novel measurement system based on a 3D camera to register the shape and dimensions of the current collector contact strips surface. The system was installed above the railway track for tests in target ambient. During the trial operation a few dozen of contact...
-
Images revealing the effect of local femtosecond laser ablation of conductive poly(lactic acid) 3D printed electrodes
Dane BadawczeThe dataset reveals the images of the femtosecond laser (FSL) ablation at the surface of commercially available carbon black-filled poly(lactic acid) 3D printed electrode. The process is used for the increase of the charge transfer of this electrode in electrochemical studies.
-
A three-dimensional meso-scale approach to concrete fracture based on combined DEM with x-ray micro-CT images
PublikacjaArtykuł omawia wyniki numeryczne uzyskane stosując 3-wymiarowy mezoskopowy model do opisu pękania w betonie na poziomie kruszywa w belce z nacięciem podczas zginania. Do obliczeń użyto metodę elementów dyskretnych. Beton został opisany jako materiał 4-fazowy złożony z kruszywa, zaprawy, makro-porów i stref przejściowych miedzy kruszywem a zaprawą. Kształt i położenia kruszywa przyjęto na podstawie skanów z mikro-tomografu. Uzyskano...
-
Caffeine detection using CB-PLA electrode after Nd:YAG laser ablation in He atmosphere
Dane BadawczeThe dataset contains electrochemical studies in form of cyclic voltammetry (CV) and differential pulse voltammetry (DPV) of laser-activated 3D printed CB-PLA electrodes. The ablation of the 3D-printed CB-PLA electrodes was carried out using a pulsed LaserBlast 500 Nd:YAG laser (Quantel, France) operating at 1064 nm and a 6 ns pulse duration.
-
"3D-Breast System for Determining the Volume of Tissue Needed for Breast Reconstruction"
PublikacjaThis article presents methods for surface reconstruction and volume determination based on the point cloud created by 3D imaging. Such a system would be used to accurately estimate breast volume in patients classified for breast reconstruction surgery at plastic surgery centers. To develop such a system, various methods of determining volume, based on images from the Intel D435i camera, were tested. In addition, an application...
-
Seafloor characterisation using multibeam data: sonar image properties, seabed surface properties and echo properties
PublikacjaIn the paper, the approach to seafloor characterisation is presented. The multibeam sonars, besides their well verified and widely used applications like high resolution bathymetry and underwater object detection and imaging, are also the promising tool in seafloor characterization and classification, having several advantages over conventional single beam echosounders. The proposed approach relies on the combined, concurrent use...
-
The electrochemical studies of CB-PLA surface activation by electrolysis in 1M NaOH
Dane BadawczeThe dataset contains the electrochemical studies performed under different conditions of surface activation of the CB-PLA 3D printed electrodes. The activation was performed by electrolysis in 1M NaOH solution under cycling polarization with different anodic or cathodic overpotentials (data in different subfolders). The file names contain the exact...
-
Structural analysis and physico-chemical characterization of mononuclear manganese(II) and polynuclear copper(II) complexes with pyridine-based alcohol
PublikacjaTwo novel manganese(II) and copper(II) complexes, mononuclear [Mn(H2O)2(2-(CH2)2OHpy)2](NO3)2 (1) and polynuclear [Cu(SO4)(2-(CH2)2OHpy)2]n (2), based on 2-(hydroxyethyl)pyridine (2-(CH2)2OHpy) were synthesised and fully characterised using X-ray structure analysis as well as spectroscopic, magnetic and thermal methods. Both central metal ions Mn(1) and Cu(1) are coordinated by two N,O-donor 2-(CH2)2OHpy ligands and possess an...
-
An unusual four-nuclear Pb(II)-pyrrole-2-carboxylato polymer: The effect of the lone pair and non-covalent interactions on the supramolecular assembly and fluorescence properties
PublikacjaThe reaction of Pb(NO3)2 with 1H-pyrrole-2-carboxylic acid (2prCOOH) leads to the formation of a new four-nuclear Pb(II) polymer, [Pb4(2prCOO)8(H2O)]n, which has been characterized by CHN, FT-IR, TG, PL and single-crystal X-ray diffraction methods. In view of the primary Pb–O bonds, Pb1 and Pb3 show hemidirected pentagonal pyramidal geometries, while Pb2 and Pb4 display hemidirected octahedral geometries. The topology of the strongest...
-
Performance of a new commercial high-definition 3D patient specific quality assurance system for CyberKnife robotic radiotherapy and radiosurgery
PublikacjaConventional two dimensional and low-definition measurement techniques for dosimetric verification of radiotherapy treatment deliveries are no longer adequate in the era of hypofractionation and extremely high dose gradients. New quality assurance (QA) tools with 3D capability and high definition are urgently needed. The purpose of this study was to evaluate the performance of one of the first such commercial systems as applied...
-
SIMULATIONS OF FRACTURE IN CONCRETE BEAMS UNDER BENDING USING A CONTINUUM AND DISCRETE APPROACH
PublikacjaThe paper describes two-dimensional meso-scale results of fracture in notched concrete beams under bending. Concrete was modelled as a random heterogeneous 4-phase material composed of aggregate particles, cement matrix, interfacial transitional zones and air voids. Within continuum mechanics, the simulations were carried out with the finite element method based on a isotropic damage constitutive model enhanced by a characteristic...
-
Surface Roughness Evaluation in Thin EN AW-6086-T6 Alloy Plates after Face Milling Process with Different Strategies
PublikacjaLightweight alloys made from aluminium are used to manufacture cars, trains and planes. The main parts most often manufactured from thin sheets requiring the use of milling in the manufacturing process are front panels for control systems, housing parts for electrical and electronic components. As a result of the final phase of the manufacturing process, cold rolling, residual stresses remain in the surface layers, which can influence...
-
Texture or Linker? Competitive Patterning of Receptor Assembly toward Ultra-Sensitive Impedimetric Detection of Viral Species at Gold-Nanotextured Titanium Surfaces
PublikacjaIn this work, we study the electrodes with a periodic matrix of gold particles pattered by titanium dimples and modified by 3-mercaptopropionic acid (MPA) followed by CD147 receptor grafting for specific impedimetric detection of SARS-CoV-2 viral spike proteins. The synergistic DFT and MM/MD modeling revealed that MPA adsorption geometries on the Au–Ti surface have preferential and stronger binding patterns through the carboxyl...
-
Contact with coupled adhesion and friction: Computational framework, applications, and new insights
PublikacjaContact involving soft materials often combines dry adhesion, sliding friction, and large deformations. At the local level, these three aspects are rarely captured simultaneously, but included in the theoretical models by Mergel et al., (2019). We here develop a corresponding finite element framework that captures 3D finite-strain contact of two deformable bodies. This framework is suitable to investigate sliding friction even...
-
Experimental validation of the rolling resistance measurement method including updated draft standard
PublikacjaThe main objective of ROSANNE is the harmonisation and standardisation of the measurement of skid resistance, noise emission and rolling resistance of road pavements. Regarding rolling resistance characterisation, a draft for standardization of a harmonized procedure for classification of road surfaces across Europe has been prepared within WP3 (deliverable 3.5). The procedure deals with the direct measurement on real roads of...
-
Naturally-derived hydrogels for 3D pancreatic tumor models: A short review
PublikacjaStatistics suggest a high proportion of mortality rate by pancreatic cancer, which is a solid tumor characterized by high heterogeneity and the presence of a complex extracellular matrix. The very low effectiveness of pancreatic cancer treatment roots in the high metastatic potential and drug resistance of this tumor. Therefore, the quest for efficient cellular models enabling precise mimicking in vivo conditions, and anticancer...
-
Pozyskiwanie i wizualizacja geodanych - (WILiŚ, GiK, st. II, sem. 1) - rok 2022/2023
Kursy OnlineCelem przedmiotu jest zapoznanie studenta z możliwościami wykorzystania języków skryptowych Python\ArcGIS Pro do pozyskiwania i wizualizacji geodanych. Po zakończeniu przedmiotu student zna podstawowe funkcje dostępne w Python\ArcGIS Pro, potrafi poprawnie wizualizować dane pomiarowe w przestrzeni 2D oraz 3D, zna funkcje niezbędne do wykonania zaawansowanych wizualizacji oraz ich edycji.
-
MODELLING OF CONCRETE FRACTURE AT AGGREGATE LEVEL USING DEM BASED ON X-RAY mu CT IMAGES OF INTERNAL STRUCTURE
PublikacjaThe paper describes two-dimensional meso-scale numerical results of fracture in notched concrete beams under quasi-static three-point bending. Concrete was modelled as a random heterogeneous 4-phase material composed of aggregate particles, cement matrix, interfacial transitional zones (ITZs) and air voids. As a numerical approach, the discrete element method (DEM) was used. The concrete micro-structure in calculations was directly...
-
Structural motifs in the Cu(II), Mn(II) and Zn(II) complexes based on N,N,N-donor dipodal or N,N,N,N-donor tripodal ligands obtained in situ: Synthesis, crystal structures and xanthine oxidase inhibition properties
PublikacjaA series of four novel transition metal complexes, [Cu(NCS)2L1] (1), [Mn(NCS)2L1] (2) where L1 = bis(1-(3,5-dimethylpyrazolyl)methyl)amine, [Mn(NCS)2L2] (3) and [Zn(NCS)L2]2[Zn(NCS)4] (4) where L2 = tris(1-(3,5-dimethylpyrazolyl)methyl)amine, has been obtained in situ by a one-step, one-pot synthetic path starting from 1-hydroxymethyl-3,5-dimethylpyrazole (L). The isolated complexes were fully characterised by elemental analysis,...