Wyszukiwarka
Filtry
wszystkich: 736
Wyniki wyszukiwania dla: RATE COEFFICIENT
-
Wpływ kierunku rozchodzenia się fali detonacyjnej oraz współczynnika asymetrii na rozkład prędkości odkształceń w kotlinie walcowniczej podczas asymetrycznego walcowania pasma Al-Cu. The influences of the direction of explosion wave and asymetrical coefficient at the distribution of strain rate in the roll cap of bimetallic plate Al-Cu of rolling process.
PublikacjaPrzedstawiono symulacje komputerowe walcowania blach Al-Cu łączonych wybuchowo. Symulacje przeprowadzono dla procesu walcowania w walcarce o średnicy walców D=150 mm z indywidualnym napędem walców roboczych. W ramach badań numerycznych określony został wpływ kierunku rozchodzenia się fali detonacyjnej na rozkład prędkości odkształcenia w kotlinie walcowniczej asymetrycznie walcowanej blachy bimetalowej Al-Cu.
-
Natural ventilation performance of family building in cold climate during windless time
PublikacjaIn this paper, the field measurements results are presented on the stack ventilation effect. The paper presents the results of performance (air change rate ACH) natural ventilation for building with inlet gap measured for the transitional season (between heating and summer season). The measurements were performed during a windless time. The house was located in northern Poland, in a cold climate region. The measurement system...
-
The unstable thermoelectric effect in non-stoichiometric Cu2Se during the non-equilibrium phase transition
PublikacjaThe superionic α ↔ β phase transition in Cu1.96Se thermoelectric material is investigated by means of thermal analysis (DSC) and measurements of Seebeck coefficient and electrical conductivity. Results of the DSC measurements with 1–10 K/min heating and cooling rates show that the material is close to the equilibrium phase composition during the transformation. However, the kinetic limitation of the process exists, which is indicated...
-
Refined theoretical study of radiative association: Cross sections and rate constants for the formation of SiN
PublikacjaRadiative association of silicon mononitride (SiN) in its two lowest molecular electronic states is studied through quantum and classical dynamics. Special attention is paid to the behavior of the cross section at high collision energies. A modified expression for the semiclassical cross section is presented which excludes transitions to continuum states. This gives improved agreement with quantum mechanical perturbation theory...
-
Does migration lead to economic convergence in an enlarged European market?
PublikacjaThis paper examines the relationship between migration and convergence for the enlarged internal market of the European Union (EU27) for the period 1990-2007. The impact of migration on growth is estimated in two ways: by including the migration rate in a growth regression and examining its impact on the convergence coefficient; and from the actual coefficient on migration, which can be interpreted as the effect of migration on...
-
A facile strategy for reclaiming discarded graphite and harnessing the rate capabilities of graphite anodes
PublikacjaGraphite negative electrodes are unbeaten hitherto in lithium-ion batteries (LiBs) due to their unique chemical and physical properties. Thus, the increasing scarcity of graphite resources makes smart recycling or repurposing of discarded graphite particularly imperative. However, the current recycling techniques still need to be improved upon with urgency. Herein a facile and efficient hydrometallurgical process is reported to...
-
Formation of carbon monoxide by radiative association: a quantum dynamical study
PublikacjaRate coefficients for the formation of carbon monoxide (CO) by radiative association of carbon and oxygen atoms are computed using quantum dynamical simulations. At temperatures above 10 K CO radiative association is dominated by C(3P) and O(3P) approaching on the A1Π potential energy curve. The rate coefficient is estimated as k=A(T/300 K)αexp−β/T with A= 1.39 × 10−18 cm3 s−1, α=−0.016 and β= 92.2 for temperatures between 6 and...
-
Effect of oxygenation time on signal of a sensor based on ionic liquids
PublikacjaThe paper presents an oxygen sensor based on ionic liquids and solid electrodes. The following ionic liquids have been employed: [BMIM][BF4], [HMIM][Cl], [BMIM][N(CN2)]. Minimum time of the sensor exposure to analyte, after which the signal (current intensity) was stable, has been evaluated. An impact of volumetric flow rate of analyte on the sensor exposure time and signal has been determined. A product of permeability coefficient...
-
A New Direct-Sequence Spread Spectrum Signal Detection Method for Underwater Acoustic Communications in Shallow-Water Channel
PublikacjaDirect-Sequence Spread Spectrum (DSSS) is one of the modulation and coding techniques used in Underwater Acoustic Communication (UAC) systems for reliable data transmision even at low signal levels. However, in a shallow water channel, there is a strong multipath propagation which causes a phase fluctuation of the received signal, affecting the performance of the spread-spectrum system. The article presents a differential method...
-
Poly(hydroxybutyrate-co-hydroxyvalerate) as a biodegradable binder in a negative electrode material for lithium-ion batteries
PublikacjaIn this work, graphite-based negative electrode for lithium-ion battery consisting a novel and biodegradable binder poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) is compared with standard graphite electrode with polyvinylidene fluoride (PVDF) as a binder. The rate and cycling performance of lithium ion insertion/extraction of electrodes with PHBV in a half-cell configuration are evaluated. Moreover, on the basis of the electrochemical...
-
Vibrational Quenching of Optically Pumped Carbon Dimer Anions
PublikacjaCareful control of quantum states is a gateway to research in many areas of science such as quantum information, quantum-controlled chemistry, and astrophysical processes. Precise optical control of molecular ions remains a challenge due to the scarcity of suitable level schemes, and direct laser cooling has not yet been achieved for either positive or negative molecular ions. Using a cryogenic wire trap, we show how the internal...
-
Ab initio chemical kinetics of Isopropyl acetate oxidation with OH radicals
PublikacjaGlobal reactivity descriptors of isopropyl acetate (IPA) and thermo-kinetic aspects of its oxidation via OH radicals have been studied. Transition state theory (TST) was utilized to estimate the bimolecular rate constants. Ten oxidation pathways have been investigated, and all of them are exothermic. The potential energy diagram has been sketched using different pre- and post-reactive complexes for all reaction pathways. Rate coefficient...
-
Using wearable device for biomedical signal acquisition and processing
PublikacjaIn this paper we present the research conducted on synchronous measurements of biosignals. The experiment was conducted to evaluate the possibility of estimating vital signs based on eye tracking. Method: The eGlasses platform was used for acquisition of ECG, respiration rate, eye and pupil movement and blood pressure. Data were acquired in three 5 min. intervals during which a subject was performing certain tasks. The signals...
-
Treatment of landfill leachate in a constructed free water surface wetland system over a decade – Identification of disturbance in process behaviour and removal of eutrophying substances and organic material
PublikacjaAn 8 ha free water surface wetland system in Örebro, Sweden, which has sediment traps followed by 10 ponds for treatment of landfill leachate in the methanogenic stage, was studied from 2003 to 2012. The wetland was irregularly loaded and the leachate characteristics showed high temporal and spatial variability, so Multivariate Statistical Process Control was chosen as the diagnostic tool for detecting anomalies prior to assessing...
-
INWESTYCJE ALTERNATYWNE – OPŁACALNOŚĆ A RYZYKO
PublikacjaW rozprawie określono pojęcie oraz miejsce inwestycji alternatywnych na rynku inwestycyjnym. Wskazane zostały atrybuty tych inwestycji. Zbudowano klasyfikację inwestycji alternatywnych w podziale na kategorie oraz typy wraz ze wskazaniem powiązań pomiędzy poszczególnymi produktami. Dokonano autorskiego podziału analizowanych inwestycji na aktywne i pasywne. Zbadano stopę zwrotu i ryzyko pięćdziesięciu inwestycji alternatywnych,...
-
Cylindrical orifice testing in laminar flow with the orifice diameter ratio β = 0.5
PublikacjaThe paper presents the results of an experimental study of a cylindrical orifice with the orifice diameter ratio β = 0.5 and the flow opening length‑to‑diameter ratio L/d = 1, with hydraulic oil flowing in the DN50 measuring channel. The measurements of the values characterising the oil flow were made in the laminar flow regime, for the Reynolds numbers ranging between Re = 100 to 950. Based on the experimental tests, standard...
-
Comparison of heat transfer characteristics in surface cooling using microjets with water, ethanol and HFE7100 as test fluids
PublikacjaAccurate control of cooling parameters is required in ever wider range of technical applications. It is known that reducing the dimensions of the size of nozzle leads to an increase in the economy of cooling and improves its quality. Present study describes research related to the design and construction of the nozzles and microjet study, which may be applied in many technical applications such as in metallurgy, electronics, etc....
-
Influence of temperature on the activity of anammox granular biomass.
PublikacjaThe aim of this study was to determine a short-term and long-term effect of temperature on the anammox rate and determination of temperature coefficients in the Arrhenius and Ratkowsky equations. The short-term effects of temperature on the anammox granular biomass were investigated in batch tests at ten different temperatures in the range of 10–55 °C. The maximum overall nitrogen removal rate of 1.3 gN gVSS−1·d−1 was observed...
-
Flow boiling of R1233zd(E) in a 3 mm vertical tube at moderate and high reduced pressures
PublikacjaThe results of flow boiling of R1233zd(E) in a 3 mm vertical stainless steel tube are presented at moderate and high saturation temperatures. Integral flow characteristics in the form of pressure drop and heat transfer coefficient are discussed for saturation temperatures ranging from 115 to 145 °C (corresponding reduced pressures from 0.2 to 0.7), mass velocity of 800 kg/m2s and heat flux of 20 kW/m2. All of the obtained heat...
-
Comparison of various flow maldistribution quantification methods in mini heat exchangers
PublikacjaThe aim of study is to compare various flow maldistribution quantification methods, using velocity, mass flow rate, pressure, and temperature. An experimentally validated numerical study has been prepared and a heat exchanger with 34 semi-circular channels with a diameter of 3.1 mm has been tested. The minichannels were heated from the bottom with a heat flux of 50, 60, 70, and 80 kW/m2. The cases for various inlet velocities of...
-
Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites
PublikacjaHybrid aluminium metal matrix composites have the potential to replace single reinforced aluminium metal matrix composites due to improved properties. Moreover, tribological performance is critical for these composites, as they have extensive application areas, such as the automotive, aerospace, marine and defence industries. The present work aims to establish the tribological characteristics of Al7068/Si3N4/BN hybrid metal matrix...
-
Ozone nanobubble technology as a novel AOPs for pollutants degradation under high salinity conditions
PublikacjaConventional water treatment systems frequently exhibit diminished efficiency at high salinity - a significant issue especially for real industrial effluents - mostly due to the creation of intricate structures between pollutants and salts. One of the primary obstacles associated with high salinity conditions is the generation of by-products that pose additional hurdles for treatment. In this work, we have investigated the novel...
-
Partition of friction heat between sliding semispaces due to adhesion-deformational heat generation
PublikacjaAnalytical expressions of heat-partition coefficient and contact temperatures for two sliding semispaces with account for adhesion-deformational heat generation and contact heat exchange have been obtained. The rate of deformational heat generation is assumed to decay exponentially with increase of distance from the interface. It has been shown that heat-generation configuration and the intensity of contact heat exchange have impact...
-
Zastosowanie addytywów w separacji pianowej białek serwatkowych i białek mlecznych
PublikacjaZaproponowano proces separacji pianowej do wydzielania białek ze strumieni poprodukcyjnych przemysłu mleczarskiego Ponadto zaproponowano zastosowanie w separacji pianowej białek serwatkowych i mlecznych addytywów dopuszczonych ustawą do stosowania w żywności. Jako cel pracy przyjęto uzyskanie wyników uzasadniających wybór takich addytywów, które intensyfikują przebieg i polepszają wynik procesu separacji pianowej białek. W części...
-
SORPTION OF SELECTED CHLORINATED SOLVENTS ON PLANT DEBRIS COLLECTED IN A CITY PARK
PublikacjaDebris from deciduous trees in the form of park green waste was investigated as a potential biosorbent for the removal of chlorinated solvents from water. The sorption properties of beech leaves and cupules, oak leaves and acorns, birch leaves and lime leaves (all tree species common for a moderate climate) in a non-modified form were investigated with regard to the removal of perchloroethylene, 1,1,2-trichloroethane and 1,1,1,2-tetrachlorothane....
-
Numerical simulation of cold flow and combustion in a swirl stabilized combustor
PublikacjaA numerical simulation model was developed to investigate the cold flow and combustion using Ansys FLUENT 2021R1. The governing equations were solved using the pressure-based method, and pressure–velocity coupling was performed using the SIMPLE method. To model the turbulent process, the RSM model was used. Non-premixed model is chosen to solve the chemical kinetics between fuel and oxigen. Radiation heat transfer was calculated...
-
Degradation of bisphenol S – a contaminant of emerging concern - by synergistic ozone and percarbonate based AOP
PublikacjaDegradation of bisphenol S was studied using ozone activated by sodium percarbonate and the effectiveness of optimized process was compared with the peroxone process. The influence of several factors including sodium percarbonate concentration, ozone dose, pH, and water matrix were investigated. A synergetic coefficient of 3.84 was achieved for the combination of sodium percarbonate and ozone, confirming the effectiveness of this...
-
Experimental investigation on straight and u-bend double tube heat exchanger with active and passive enhancement methods
PublikacjaAuthors in this work want to demonstrate the possibility to increase the heat transfer efficiency by using simple wire coil inserts to create turbulent flow in the boundary layer as well as air blowing into the annulus of the pipe. In the study, Wilson plot approach was applied in order to estimate heat transfer coefficients for all heat exchanger (HX) configurations. The study focuses on experimental values of heat transfer coefficient...
-
Decoupled Kalman filter based identification of time-varying FIR systems
PublikacjaWhen system parameters vary at a fast rate, identification schemes based on model-free local estimation approaches do not yield satisfactory results. In cases like this, more sophisticated parameter tracking procedures must be used, based on explicit models of parameter variation (often referred to as hypermodels), either deterministic or stochastic. Kalman filter trackers, which belong to the second category, are seldom used in...
-
TiO2 and Reducing Gas: Intricate Relationships to Direct Reduction of Iron Oxide Pellets
PublikacjaIn response to the imperative for sustainable iron production with reduced CO2 emissions, this study delves into the intricate role of TiO2 in the direct reduction of iron oxide pellets. The TiO2-dependent reducibility of iron oxide pellets utilizing H2 and CO gas across varied temperatures and gas compositions is thoroughly investigated. Our findings unveil the nuanced nature of the TiO2 effect, underscored by its concentration-dependent...
-
The effect of aeration mode (intermittent vs. continuous) on nutrient removal and greenhouse gas emissions in the wastewater treatment plant of Corleone (Italy)
PublikacjaThe paper reports the results of an experimental study aimed at comparing two configurations of a full-scale wastewater treatment plant (WWTP): conventional activated sludge (CAS) and oxic-settling-anaerobic process (OSA) with intermittent aeration (IA). A comprehensive monitoring campaign was carried out to assess multiple parameters for comparing the two configurations: carbon and nutrient removal, greenhouse gas emissions, respirometric...
-
Graphene-based Silicone rubber Nanocomposites: Preparation, Characterization, and Properties
PublikacjaThis study aims to understand better the mechanical, thermal, and tribological behavior of silicone rubber nanocomposites. Graphite, exfoliated graphite, reduced graphene oxide, ionic liquid modified graphene oxide, silane-modified graphene oxide, fumed silica, and other fillers were used in this study. Adding graphene-based fillers to the silicone rubber matrix substantially improves the nanocomposite's mechanical, thermal, and...
-
Flow maldistribution and its mitigation in mini heat exchangers
PublikacjaIn the present paper, a detailed numerical investigation has been carried out to analyze the flow maldistribution in 50 parallel 1 mm x 1 mm rectangular minichannels and 1 mm depth minigap section with rectangular, trapezoidal, triangular or concave mani-folds in Z-type flow configuration (16 different cases). The working medium was ethanol and the mass flow rate was 5×10-4 kg/s. Both sections was heated from the bottom side. Heat...
-
Highly stable CsFAPbIBr perovskite solar cells with dominant bulk recombination at real operating temperatures
PublikacjaMixed-cation mixed-halide perovskite solar cells have been characterized in DC at different temperatures (from −20 °C up to 50 °C) and the time evolution of the device efficiency has been assessed using different degradation protocols (indoors and outdoors). The completely planar p–i–n structure is ITO/CuNiOx/PTAA/CsFAPbIBr/PCBM/PEI/Ag. Pristine current–voltage characteristics barely show hysteresis, at any temperature. Open circuit...
-
Impact of strontium non-stoichiometry of SrxTi0.3Fe0.7O3-δ on structural, electrical, and electrochemical properties for potential oxygen electrode of intermediate temperature solid oxide cells
PublikacjaThis work presents the results of a comprehensive study on the impact of the A-site non-stoichiometry of SrxTi0.3Fe0.7O3-δ (x = 0.90, 0.95, 1.00, 1.05) ceramics on their physicochemical properties. The materials were fabricated by the conventional solid-state reaction method and their structure was determined by X-ray diffractometry, X-ray photoelectron spectroscopy and electron microscopy. Their sintering and thermal expansion...
-
A new viscoelastic method of calculation of low-temperature thermal stresses in asphalt layers of pavements
PublikacjaThe paper presents a new method of calculation of thermal stresses in asphalt layers of pavements induced by cooling or heating. The method, developed by the author, is based on the analytical solution for the linear viscoelastic Burgers model extended numerically for the case of asphalt layers whose rheological parameters are strongly dependent on temperature. The coefficient of thermal expansion and Poisson’s ratio may optionally...
-
Thermohydraulic maldistribution reduction in mini heat exchangers
PublikacjaA detailed numerical investigation has been carried out to analyze the flow maldistribution in 50 parallel 1 mm × 1 mm rectangular minichannels and 1 mm depth minigap section with rectangular, trapezoidal, triangular or concave manifolds in Z-type flow configuration. The working medium was ethanol and the mass flow rate was 5 × 10−4 kg/s. Both sections were heated from the bottom side. Heat flux of 10 000 W/m2 and 5000 W/m2 was...
-
A comparative study on the decolorization of Tartrazine, Ponceau 4R, and Coomassie Brilliant Blue using persulfate and hydrogen peroxide based Advanced Oxidation Processes combined with Hydrodynamic Cavitation
PublikacjaDecolorization of Ponceau 4R, Tartrazine, and Coomassie Brilliant Blue (CBB) was studied using hybrid processes of hydrodynamic cavitation (HC) with potassium persulfate (KPS) and hydrogen peroxide (H2O2). The different properties of these dyes such as hydrophobicity, molecular structures, and molecular weights provided this opportunity to investigate the effects of these factors by comparing the decolorization values of the dyes....
-
Selected design and construction aspects of supercritical steam generators for high temperature reactors = Wybrane aspekty konstrukcyjne i projektowe generatorów pary nadkrytycznej ogrzewanych z reaktorów wysokotemperaturowych
PublikacjaW artykule zaprezentowano uwarunkowania projektowe i konstrukcyjne nadkrytycznego generatora pary (jednoprzepływowego) wykorzystującego do ogrzewania hel z reaktorów HTR i VHTR. Wymiennik helikoidalny jest preferowany dla zwiększenia wymiany ciepła i zwartości. Badano własności czynników wymieniających ciepło z parą w obszarach przy- i nadkrytycznych. Analizowano korelacje, aby wybrać najbardziej wiarygodne. Przedyskutowano najbardziej...
-
Kinetic characterization of hydrogen sulfide inhibition of suspended anammox biomass from a membrane bioreactor
PublikacjaThe inhibition effects of hydrogen sulfide (H2S) on anammox-enriched biomass from a laboratory membrane reactor were analyzed in a series of batch respirometric experiments. The determined half maximal inhibitory concentration (IC50) was 4.67 mg H2S-S L−1 at the constant pH = 7.0 and the total sulfide concentration varying between 1 and 15 mg TS-S L−1. In another test, the IC50 was found to be 4.25 mg H2S-S L−1 under a constant...
-
Co-simulation strategy of transient CFD and heat transfer in building thermal envelope based on calibrated heat transfer coefficients
PublikacjaThe paper presents a strategy to develop a fully transient numerical model of a heat transfer in building, using a transient CFD model of indoor air and a thermal envelope model, running in a co-simulation. The strategy relies on the utilization of RANS with a high-Re turbulence model and a wall function, which enables to use a coarse computational mesh limiting the computational time. Since wall functions give invalid heat transfer...
-
Artificial neural network prophecy of ion exchange process for Cu (II) eradication from acid mine drainage
PublikacjaThe removal of heavy metal ions from wastewater was found to be significant when the cation exchange procedure was used effectively. The model of the cation exchange process was built using an artificial neural network (ANN). The acid mine drainage waste’s Cu(II) ion was removed using Indion 730 cation exchange resin. Experimental data from 252 cycles were recorded. In a column study, 252 experimental observations validated the...
-
Plasmon resonance in a TiO2-Au NPs structures
Dane BadawczeInvestigated structures were deposited on a pre cleaned Corning 1737 glass substrates, which provided flat optical transmission characteristics and high transmission coefficient in a visible light range. Plasmonic nanostructures were formed as a result of thermal annealing. For gold films with thickness of 2.8 nm depiction a table-top dc magnetron sputtering...
-
Assessment of Surface Water Resources Based on Different Growth Scenarios, for Borkena River Sub-basin, Awash River Basin, Ethiopia
PublikacjaThe total annual river flow at the Awash Kombolcha sub-basin of the Borkena river station was estimated to be 4.6 billion cubic meters by 2019-2030. The current average annual flow at the exit measurement station is 544.5Mm3 of the water resources available in the study area. The monthly peak flow of the Borkena River occurs from July to September. In addition, the highest monthly average flow is in August and the lowest is...
-
The influence of crude glycerol and castor oil-based polyol on the structure and performance of rigid polyurethane-polyisocyanurate foams
PublikacjaIn this work, biopolyol obtained from two types of industrial crops’ processing products: crude glycerol and castor oil was used for preparation or rigid polyurethane-polyisocyanurate foams. Bio-based polyol was obtained via crude glycerol polymerization and further condensation of resulting polyglycerol with castor oil. Rigid polyurethane-polyisocyanurate foams were prepared at partial substitution (0–70 wt.%) of petrochemical...
-
Comparative Study of Balancing SRT by Using Modified ASM2d in Control and Operation Strategy at Full-Scale WWTP
PublikacjaDetailed knowledge on the composition of the influent going into the wastewater treatment system is essential for the development of a reliable computer model. In the context of WWTPs (wastewater treatment plants), the wastewater characteristics are not only important for activated sludge system modelling, but also have an impact on the appropriate control of single unit operations. The aim of this study was to evaluate the concepts...
-
The harmonic distortion of voltage waveforms in the ship's electrical power system
Dane BadawczeThe dataset is a part of the research results on the quality of supply voltage on bus bars of the ship's electrical power system's main switchboard in different states of ship exploitation. The attached dataset contains the results of a harmonic distortion analysis expressed by the total harmonic distortion (THD) coefficient of voltage waveforms recorded...
-
Low temperature growth of diamond films on optical fibers using Linear Antenna CVD system
PublikacjaIt is not trivial to achieve a good quality diamond-coated fibre interface due to a large difference in the properties and composition of the diamond films (or use coating even) and the optical fibre material, i.e. fused silica. One of the biggest problems is the high temperature during the deposition which influences the optical fibre or optical fibre sensor structure (e.g. long-period gratings (LPG)). The greatest advantage of...
-
Elucidating charge transfer process and enhancing electrochemical performance of laser-induced graphene via surface engineering with sustainable hydrogel membranes: An electrochemist's perspective
PublikacjaLaser-induced graphene (LIG) has emerged as a promising solvent-free strategy for producing highly porous, 3D graphene structures, particularly for electrochemical applications. However, the unique character of LIG and hydrogel membrane (HM) coated LIG requires accounting for the specific conditions of its charge transfer process. This study investigates electron transfer kinetics and the electroactive surface area of LIG electrodes,...
-
CO2 capture using steam ejector condenser under electro hydrodynamic actuator with non-condensable gas and cyclone separator: A numerical study
PublikacjaThe concept for condensation of steam and CO2 separation in a negative CO2 emission gas power plant involves the utilization of a steam ejector condenser (SEC) for direct-contact condensation of vapor with inert gas (CO2) on a spray of subcooled liquid, integrated with a separator to produce pure CO2. Due to the increasing diffusion resistance and reduced convective heat transfer between the steam and subcooled water phases...