Wyszukiwarka
Wyniki wyszukiwania dla: stress evaluation
-
Residual stress evaluation in oil pipeline.
PublikacjaPrzedstawiono metodę pomiaru rozkładu naprężeń w ropociągu z wykorzystaniem efektu Barkhausena. Opisano procedurę pomiaru oraz kalibracji metody. Wynik potwierdzono w jednym punkcie metodą Mathar´a
-
Preparation to ball on disk test Initial contact stress evaluation
Dane BadawczeEvaluation of initial contact stress in tests on wear of Al6061 alloy in ball on disk tribological testing. Research on the reinforcing effect of aluminium alloy injection reinforcement with TiN and WC powders in laser remelted surface layer.
-
Progress in the post weld residual stress evaluation using Barkhausen effect meter with a novel rotating magnetic field probe
PublikacjaWe report the progress in post weld residual stress evaluation using Barkhausen effect (BE) meter with rotating magnetic field probe. The novel probe of the BE meter contains two C-core electromagnets and searching coil with ferrite antenna. This meter allows automatic measurements of BE intensity envelopes at different angles of magnetizing field. The full process of measurement at given position of the probe takes about only...
-
Fatigue damage evaluation of organic coatings subjected to mechanical stress
PublikacjaZnaczna liczba konstrukcji ulega niszczeniu zmęczeniowemu w wyniku oddziaływania cyklicznych naprężeń mechanicznych. Jednakże w dziedzinie organicznych powłok ochronnych czynnik ten pozostaje niedoceniany. W pracy dokonano porównania wpływu cyklicznych naprężeń mechanicznych na nowe i pre-eksponowane (w podwyższonej temperaturze lub promieniowaniu UV) powłoki epoksydowe.
-
FT-Raman spectroscopy as a tool in evaluation the response of plants to drought stress
Publikacja -
Discussion of “CPT Evaluation of Yield Stress Profiles in Soils” by Shehab S. Agaiby and Paul W. Mayne
PublikacjaVeryfication of the procedure to estimate overconsolidation ratio in sands using the results of mini-cone penetration tests in centrifuge.
-
A fast procedure of stress state evaluation in magnetically anisotropic steels with the help of a probe with adjustable magnetizing field direction
PublikacjaThe paper presents a novel approach to the stress state evaluation issue. It deals with a strongly (magnetically) anisotropic materials for which a direct interpretation of the Barkhausen effect (BE) intensity would lead to erroneous results. In such a case one has to take into account both the measured BE intensity and the orientation of the magnetisation direction relative to the magnetic easy axis. For the in plane stress distribution...
-
Efficacy of coping with work-related stress by firemen
PublikacjaThe aim of this study was efficacy of coping with work-related stress by firemen with reference to subjective health evaluation. Theoretical model of process of stress by Lazarus was applied. The group consistent of 230 line-duty firemen. Participation in traumatic events and sense of coherence both directly and indirectly, by stress, affected the health among firemen. In stress confrontation a wider array of task and emotional...
-
Stress anisotropy characterisation with the help of Barkhausen effect detector with adjustable magnetic field direction
PublikacjaIn the paper we describe a novel apparatus for the measurement of the Barkhausen noise (BN) angular dependence, which in turn may be indicative of the stress induced anisotropy of magnetic properties. Such dependence can be further used for the stress distribution evaluation. The change of magnetization direction in the material is obtained by varying the magnetic flux density in two perpendicular yokes of the apparatus. We present...
-
Isoprostanes-Biomarkers of Lipid Peroxidation: Their Utility in Evaluating Oxidative Stress and Analysis
PublikacjaIsoprostanes (IsoPs) are key biomarkers for investigating the role of free radical generation in the pathogenesis of human disorders. To solve IsoPs-related problems with regard to isoprostanes, analytical tools are required. This paper reviews the problems and trends in this field focusing on the methodology for assaying biomarkers in exhaled breath condensate (EBC) samples. A large amount of work has been done in the qualitative...
-
Discussion of Derivability of Local Residual Stress Level from Magnetic Stray Field Measurement
PublikacjaThe NDT procedure dubbed ‘metal magnetic memory’ method and the related ISO 24497 standard has found wide industrial acceptance in some countries, mainly in Russia and China. The method has been claimed by some researchers (Roskosz and Bieniek in NDT&E Int 45:55–62, 2012; Wilson et al. in Sens Actuators A 135:381–387, 2007) as having potential for quantitative determination of local residual stress state in engineering structures,...
-
The effect of job-related stress on psychological well-being = Wpływ stresu zawodowego na dobrostan psychiczny
PublikacjaThe aim of the investigation was to evaluate the effect of job stress factors on psychological well-being of firemen. Goldberg's GHQ-12 for well-being evaluation, the Perceived Job Stress Questionnaire by Dudek et al. for job stress assessment, and indicator of participation in traumatic events were used. 19% of the firemen were qualified to the group with increased risk of mental disorders. Occupational stress had a strong impact...
-
Application of the Barkhausen effect probe with adjustable m agnetic field direction for stress state determination in the P91 ste el pipe
PublikacjaThe paper presents the results of application of a novel Barkhausen effect (BE) probe with adjustable magnetizing field direction for the stress level evaluation in ferromagnetic materials. The investigated sample was in a form of a pipe, made of P91 steel that was anisotropic due to the production process. The measurements were performed before and after welding, revealing the influence of welding process on the residual stress...
-
The Dominant Influence of Plastic Deformation Induced Residual Stress on the Barkhausen Effect Signal in Martensitic Steels
PublikacjaThe paper presents the results of investigation of the influence of plastic deformation on the magnetic properties of martensitic steel (P91 grade). The properties of the hysteresis loops as well as of the Barkhausen effect (BE) signal are analysed for both tensile and compressive loading up to ε = 10% of plastic deformation. The choice of the steel and of the deformation range is unique, since for such combination one can expect...
-
Optimal shape and stress control of geometrically nonlinear structures with exact gradient with respect to the actuation inputs
PublikacjaThis paper presents an efficient and robust optimization methodology for stress and shape control of actuated geometrically nonlinear elastic structures, applied to 3D trusses. The actuation inputs, modeled as prescribed strains, serve as the optimization variables. The objective is to minimize total actuation while satisfying several constraints: (i) actuation bounds in each actuated element and (ii) target ranges for nodal displacements...
-
Mariusz Kaczmarek dr hab. inż.
OsobyReceived M.Sc., Eng. in Electronics in 1995 from Gdansk University of Technology, Ph.D. in Medical Electronics in 2003 and habilitation in Biocybernetics and Biomedical Engineering in 2017. He was an investigator in about 13 projects receiving a number of awards, including four best papers, practical innovations (7 medals and awards) and also the Andronicos G. Kantsios Award and Siemens Award. Main research activities: the issues...
-
Drought stress memory and subsequent drought stress tolerance in plants
Publikacja -
Psychosocial stress and cortisol stress reactivity predict breast milk composition
Publikacja -
Ellipticity in couple-stress elasticity
PublikacjaWe discuss ellipticity property within the linear couple-stress elasticity. In this theory, there exists a deformation energy density introduced as a function of strains and gradient of macrorotations, where the latter are expressed through displacements. So the couple-stress theory could be treated as a particular class of strain gradient elasticity. Within the micropolar elasticity, the model is called Cosserat pseudocontinuum...
-
Biharmonic reduced stress.
PublikacjaRozpatrywane jest wieloosiowe naprężenie o biharmonicznych składowych. Aproksymuje ono m.in. naprężenie w rufowej części kadłuba statku przy regularnym falowaniu morskim. Celem pracy jest zamodelowanie tego naprężenia jednoosiowym naprężeniem zredukowanym. Dla uniknięcia zniekształcenia widma naprężenia wyznaczono biharmoniczne naprężenie zredukowane. W tym celu wykorzystano hipotezę uśrednionej energii odkształcenia postaciowego.
-
Evaluation of thermal cracking probability for asphalt concretes with high percentage of RAP
PublikacjaThe paper presents determination of the probability of thermal cracking of asphalt mixtures with different reclaimed asphalt pavement (RAP) content on the basis of laboratory tests and analytical evaluation using thermal stress development method. Probability was evaluated taking into consideration: the type and gradation of the mixture and the quality and content of RAP. Thermal stresses were determined using two models: elastic and...
-
Some problems of slide bearing material fatigue evaluation.
PublikacjaA slide bearing alloy resistance against fatigue failures have been investigated for three different lubricants, different heat loadings and different stress ratio κ values. The research methods and data handling procedures for determination of particular parameter effects on fatigue strength have been described and analysed for experiments that were set and performed in laboratory tester SKMR-2. Main and interaction effects of...
-
Calculations of notch stress factor of a thin-walled spreader bracket fillet weld with the use of a local stress approach
PublikacjaPresence of geometric notches in welded joints causes concentration of strains and stresses, therefore reducing fatigue strength of such joints. This article presents an analysis of stress concentrations in a fillet weld of a spreader mounting bracket on a small sailing yacht. The aim of this article is to direct the attention of designers, manufacturers and regulatory bodies to issues of fatigue cracks that form in brackets fastening...
-
Resonant DC link inverters for AC motor drive systems – critical evaluation
PublikacjaIn this survey paper, resonant and quasiresonant DC link inverters are reexamined for AC motor drive applications. Critical evaluation of representative topologies is based on simulation and waveform analysis to characterize current/voltage stress of components, control timing constraints and feasibility. A special concern over inverter common-mode voltage and voltage gradient du/dt limitation capacity is discussed for motor bearing...
-
EXPERIMENTAL EVALUATION OF DLC/STEEL SLIDING CONTACTS’ OPERATIONAL ENVELOPE
PublikacjaIn an industrial project concerning sliding bearings, a sliding pair was selected of high alloy steel vs. industrial grade DLC coated high alloy steel as a basis for an innovative design of high performance sliding bearings lubricated with a synthetic oil for use in geared transmission units. The development process required credible data on the ultimate resistance of the sliding pair to very high contact stress. An experimental...
-
Determinants of stress in the company perfecting quality
Publikacja -
The Influence of Oxidative Stress on Thyroid Diseases
Publikacja -
Evaluation of reformer tubes degradation after long term operation
PublikacjaPurpose of this paper is to show the effect of long-term service at elevated temperatures on microstructural changes of cast steel reformer tubes made of the alloy IN-519 (24%Cr, 24%Ni, Nb). The relationship between mechanical properties and microstructure degradation is discussed. Investigations were performed on five tubes taken from ammonia reformer furnace. Tubes worked at temperature of 880C and 3,2 MPa pressure. The operation...
-
Stress Monitoring System for Individuals with Autism Spectrum Disorders
PublikacjaIn this article, a stress monitoring system tailored for individuals with Autism Spectrum Disorders (ASD) and developed for the educational institution is presented. People with ASD face problems with effective stress management due to their high self-perceived levels of stress, poor ability to cope with it, and dificulties with the accurate detection of the source of stress. Consistently, being able to measure stress appears to...
-
On the effective properties of foams in the framework of the couple stress theory
PublikacjaIn the framework of the couple stress theory, we discuss the effective elastic properties of a metal open-cell foam. In this theory, we have the couple stress tensor, but the microrotations are fully described by displacements. To this end, we performed calculations for a representative volume element which give the matrices of elastic moduli relating stress and stress tensors with strain and microcurvature tensors.
-
Stress analysis of a strip under tension with a circular hole
PublikacjaThe paper addresses stress analysis of a strip with a circular hole under uniform uniaxial tension based oncircumferential stress expressionρπ. Stresses are analyzed in the infinite-length strips under tension with holes, the ratioof the hole radiusa to the strip half-widthb is either equal to:κ =a/b = 0.1 orκ = 0.5. Circumferential stresses aredetermined in selected cross-sections of the strip. The stress diagrams display local...
-
Propagation of acoustic pulses in some fluids with yield stress
PublikacjaThis study is devoted to the derivation of approximate equations governing acoustic pulses in flows with yieldstress, including some time-dependent flows with a slow dependence on time of yield stress and apparent viscosity. Themodeling of yield stress and apparent viscosity in the vicinity of a zero deformation rate allows us to consider a thixotropicfluid as a Bingham plastic with coefficients that are dependent on time. The...
-
A hyperelastic model for soils with stress-induced and inherent anisotropy
PublikacjaIn this paper, modelling of the superposition of stress-induced and inherent anisotropy of soil small strain stiffness is8presented in the framework of hyperelasticity. A simple hyperelastic model, capable of reproducing variable stress-induced9anisotropy of stiffness, is extended by replacement of the stress invariant with mixed stress–microstructure invariant to10introduce constant inherent cross-anisotropic component. A convenient...
-
Stress Detection of Children With ASD Using Physiological Signals
PublikacjaThis paper proposes a physiological signal-based stress detection approach for children with autism spectrum disorder (ASD) to be used in social and assistive robot inter- vention. Electrodermal activity (EDA) and blood volume pulse (BVP) signals are collected with an E4 smart wristband from children with ASD in different countries. The peak count and signal amplitude features are derived from EDA signal and used in order to detect...
-
Stress analysis of the bridge hangers in terms of the fatigue verification
PublikacjaThe paper presents the results of numerical stress analysis of the bridge rod hangers. Two types of hangers were taken into account, i.e. the bolted hanger and the welded hanger. A detailed FEM shell models of the connection area between the hanger and the bridge span have been developed. Local stress concentration effects have been investigated in terms of fatigue verification.
-
Effects of mechanical stress on electrical arameters and noise of supercapacitors
PublikacjaResults of noise and electrical parameters measurements of prototype electrochemical double layer capacitors (EDLC) are reported at the presence of selected mechanical stress. This issue is of great importance due to future applications in wearable technology. The measurement results are compared, and we may conclude than flicker noise is more sensitive to any stress than other considered electrical parameters.
-
Effect of power frequency on the stress state of disc actuator
PublikacjaThis paper presents the concept of determining the optimum frequency of coil supply in inductive-dynamic drive. As a criterion to obtain the sought frequency, the smallest value of reduced stress in the disc was assumed while maintaining the desired dynamics. The disc stress is determined on the basis of solution of vibrating thin plate equation. Magnetic pressure acting on the disc is obtained from a hybrid circumferentially-field...
-
Towards detecting programmers’ stress on the basis of keystroke dynamics
PublikacjaThe article describes the idea of detecting stress among programmers on the basis of keystroke dynamics. An experiment with a group of students of artificial intelligence classes was performed. Two samples of keystroke data were recorded for each case, the first while programming without stress, the second under time pressure. A number of timing and frequency parameters were calculated for each sample. Then statistical analysis...
-
Effect of power frequency on the stress state of disc actuator
PublikacjaThe paper presents the concept of determinig the optimum frequency of coil supply in inductive-dynamic drive. As a criterion to obtain the sought frequency, the smallest value of reduced stress in the disc was assumed while maintaining the desired dynamics.
-
A Review: Structural Shape and Stress Control Techniques and their Applications
PublikacjaThis review article presents prior studies on controlling shape and stress in flexible structures. The study offers a comprehensive survey of literature concerning the adjustment and regulation of shape, stress, or both in structures and emphasizes such control’s importance. The control of systems is classified into three primary classes: nodal movement control, axial force control, and controlling the two classes concurrently....
-
Stress analysis of suspended rail vehicle bogie
PublikacjaNiniejsza publikacja została poświęcona analizie wytrzymałościowej wybranych elementów wózka – osi zestawu kołowego i ramy. Obliczenia osi wykonano w oparciu o metodę analityczną przy rozpatrzeniu różnych materiałów jej wykonania. Do sprawdzenia wytrzymałości ramy wykorzystano metodę elementów skończonych, a obciążenie wyznaczono zgodnie z wytycznymi normy PN-EN 13749. Sam wózek jest częścią podwieszanego elektrycznego zespołu...
-
Stress-opioid interactions: a comparison of morphine and methadone
Publikacja -
Persistent oxidative stress in colorectal carcinoma patients
Publikacja -
Oxidative Stress as an Important Contributor to the Pathogenesis of Psoriasis
Publikacja -
Impact of the medical clothing on the thermal stress of surgeons
Publikacja -
Fatigue criterial parameters of variable amplitude stress.
PublikacjaPrzedstawiono oryginalne kryterialne parametry zmęczeniowe naprężenia o zmiennej amplitudzie. Dla ich wyznaczenia założono, że wydatkowana w procesie zmęczenia energia jest proporcjonalna do energii sprężystego odkształcenia postaciowego. Jeżeli przyrost zniszczenia spowodowanego przez nj cykli naprężenia o stałej amplitudzie aj jest odniesiony do energii sprężystego odkształcenia postaciowego przekazanej jednostkowej objętości...
-
Design, synthesis, and biological evaluation of tetrahydroquinolinones and tetrahydroquinolines with anticancer activity
PublikacjaColorectal cancer (CRC) is the most commonly diagnosed cancer in Europe and the United States and the second leading cause of cancer related mortality. A therapeutic strategy used for the treatment of CRC involves targeting the intracellular levels of reactive oxygen species (ROS). In this study, we synthesized a series of novel tetrahydroquinolinones and assessed their ability to inhibit CRC growth and proliferation by evoking...
-
Joanna Rymaszewska prof. dr hab. n. med.
OsobyCV Joanna Rymaszewska Wroclaw University of Science and Technology, Wroclaw, Poland +48 601 98 26 24, joanna.rymaszewska@pwr.edu.pl orcid.org/0000-0001-8985-3592 2023 → Professor of Wroclaw University of Science and Technology (WUST), Poland 2011 → 2023 Professor of Wroclaw Medical University (WMU), PL 2016 → 2022 Head of the Department of Psychiatry, Wroclaw Medical University 2016 → 2022 Head of the Clinic of Psychiatry,...
-
Intelligent microbearing project with memory of stress-strain history
PublikacjaTaking into account the increasing need of intelligent micro-bearing with memory, this paper presents the optimization, simulation and practical application of operating parameters(load carrying capacity, friction forces, friction coefficient, wear), simulation for hydrodynamic HDD micro-bearing with curvilinear nano-grooved journal profile. One of the reason of such journal profile is that this journal profile contributes to the...
-
The carbohydrate glycosylphosphatidylinositol anchor chain under mechanical stress
PublikacjaCarbohydrates have quite complicated micro heterogenic structure which may undergo different structural transitions. Due to their extreme flexibility it is very difficult to investigate such structural changes experimentally. In these studies we want to predict what structural and conformational changes are possible in the carbohydrate