Filtry
wszystkich: 841
wybranych: 719
Wyniki wyszukiwania dla: CIRCUIT MINIATURIZATION
-
Ceramic composites for single-layer fuel cells
PublikacjaComposite materials consisting of acceptor doped lanthanum orthoniobate electrolyte phase (La0.98Ca0.02NbO4) and Li2O:NiO:ZnO semiconducting phase were synthesized. The precursor powder of La0.98Ca0.02NbO4 was prepared in nanocrystalline (mechanosynthesis) and microcrystalline (solid-state synthesis) form. The composite can be applied in a single-layer fuel cell, because of the presence of two phases acting as an anode and a cathode...
-
A 1-nS 1-V Sub-1-µW Linear CMOS OTA with Rail-to-Rail Input for Hz-Band Sensory Interfaces
PublikacjaThe paper presents an operational transconductance amplifier (OTA) with low transconductance (0.62–6.28 nS) and low power consumption (28–270 nW) for the low-frequency analog front-ends in biomedical sensor interfaces. The proposed OTA implements an innovative, highly linear voltage-to-current converter based on the channel-length-modulation effect, which can be rail-to-rail driven. At 1-V supply and 1-Vpp asymmetrical input driving,...
-
Torque Transmitted by Multi-plate Wet Clutches in Relation to Number of Friction Plates and Their Dimensions
PublikacjaIn the paper results of experimental tests on multi-plate wet clutch torque capacity for various diameters and numbers of friction plates are presented. Construction of an apparatus for laboratory tests of wet clutch engagement, drag torque and maximum torque is shown. Methodology of maximum torque capacity experiment and hydraulic circuit diagram, which supplies a motor and an actuator for the experiment are described. Analytically...
-
Design Evolution of the Ultrasonic Piezoelectric Motor Using Three Rotating Mode Actuators
PublikacjaThe development process and experimental investigation of the multicell piezoelectric motor is presented in this paper. The proposed design consists of three individual cells integrated into the stator, double rotor, and a preload system. Those elements are combined into a symmetrical structure of the motor. The two new prototypes have been designed, simulated and tested. Finite element numerical analysis is carried out to obtain...
-
Polynomial description of dynamic impedance spectrogram—introduction to a new impedance analysis method
PublikacjaThis paper presents a polynomial description of spectrograms obtained using Dynamic Electrochemical Impedance Spectroscopy. A method to fit the polynomial degree correctly is discussed. A simple electrical system of a diode connected in parallel with a capacitor was used for testing. Dynamic impedance measurements during potentiodynamic polarization were conducted. This paper presents an alternative analysis method that allows...
-
A Direct Modulation for Matrix Converters based on the Onecycle Atomic operation developed in Verilog HDL.
PublikacjaThis paper presents a fast direct Pulse Width Modulation (PWM) algorithm for the Conventional Matrix Converters (CMC) developed in Verilog Hardware Description language (HDL). All PWM duty cycle calculations are performed in one cycle by an atomic operation designed as a digital module using FPGA basic blocks. The algorithm can be extended to any number of output phase. The improved version of the discontinuous Direct Analytic...
-
Superconductivity and itinerant ferromagnetism of Y9Co7 probed by ac susceptibility
PublikacjaThe ac magnetic susceptibility of a single crystal sample of the compound Y9Co7 has been measured in applied dc fields ranging from 0–6.7 kOe by utilizing a tunnel diode resonator circuit. In agreement with previous measurements on this material, a superconducting transition has been observed to occur at TSC ≈ 2.5 K. A broad maximum has been observed in the zero field susceptibility measurements from 2.5 K < T < 8 K and its behavior...
-
Computer-Aided Calculations of Earth Potential Rise in High Voltage Overhead Lines
PublikacjaHigh voltage overhead power lines with earth wires comprise towers made of conductive material. Some towers are in locations where people can be expected to be either for a long time or for a short time but very frequently. Evaluation of shock hazard near such towers requires calculation of line-to-earth short-circuit current, earth current and especially earth potential rise. Number of towers in high voltage power lines can exceed...
-
Inverse surrogate models for fast geometry scaling of miniaturized dual-band couplers
PublikacjaRe-design of microwave structures for various sets of performance specifications is a challenging task, particularly for compact components where considerable electromagnetic (EM) cross-couplings make the relationships between geometry parameters and the structure responses complex. Here, we address geometry scaling of miniaturized dual-band couplers by means of inverse surrogate modeling. Our approach allows for fast estimation...
-
Rapid multi-objective design optimisation of compact microwave couplers by means of physics-based surrogates
PublikacjaThe authors introduce a methodology for fast multi-objective design optimisation of miniaturised microwave couplers. The approach exploits the surrogate-based optimisation paradigm with an underlying low-fidelity model constructed from an equivalent circuit of the structure under consideration, corrected through implicit and frequency space mapping. A fast prediction tool obtained this way is subsequently optimised by a multi-objective...
-
Multi-objective optimization of compact UWB impedance matching transformers using Pareto front exploration and adjoint sensitivities
PublikacjaIn this paper, a technique for fast multi-objective optimization of impedance matching transformers has been presented. In our approach, a set of alternative designs that represent the best possible trade-offs between conflicting objectives (here, the maximum reflection level within a frequency band of interest and the circuit size) is identified by directly exploring the Pareto front. More specifically, the subsequent Pareto-optimal...
-
Longitudinally magnetized left-handed cylindrical ferrite coupled line junction for nonreciprocal devices
PublikacjaThis paper presents investigations of longitudinally magnetized left-handed cylindrical ferrite coupled line junction for nonreciprocal devices. The proposed junction is formed as a quasi periodic arrangement of N unit cells. Each unit cell is realized as a cascade of short cylindrical ferrite coupled lines with reactance circuit composed of series capacitors and parallel inductors. The left-handed cylindrical junction with π/4...
-
Low-cost EM-Simulation-based Multi-objective Design Optimization of Miniaturized Microwave Structures
PublikacjaIn this work, a simple yet reliable technique for fast multi-objective design optimization of miniaturized microwave structures is discussed. The proposed methodology is based on point-by-point identification of a Pareto-optimal set of designs representing the best possible trade-offs between conflicting objectives such as electrical performance parameters as well as the size of the structure of interest. For the sake of computational...
-
Nonlinear model of a synchronous generator for analysis of more electric aircraft power systems
PublikacjaA nonlinear model for studying a variable-speed synchronous generator (SG) in more electric aircraft (MEA) power system has been developed. The saturation effects of the SG magnetic circuit have been considered. The model has been implemented in the Synopys/Saber simulation environment. The modelling language MAST has been used to elaborate the SG model. The model exhibit a network with the same number of external terminals/ports...
-
Accurate modeling of quasi-resonant inverter fed IM drive
PublikacjaIn this paper wide-band modeling methodology of a parallel quasi-resonant dc link inverter (PQRDCLI) fed induction machine (IM) is presented. The modeling objective is early-design stage prediction of conductive electromagnetic interference (EMI) emissions of the considered converter fed IM drive system. Operation principles of the selected topology of PQRDCLI feeding IM drive are given. Modeling of the converter drive system is...
-
Frequency-dependent coupling model for microwave band-pass filter
PublikacjaThe goal of this work was to create a circuit model which represents frequency-dependent coupling between microwave resonators. Our models are designed for in-line filters. The frequency-dependent coupling enables one to realize a transmission zero which is not possible in classical approach with frequency independent inverters. In addition, the proposed model allows us to observe out-of-band behavior, e.g. spurious resonance....
-
Arylated carbon nanotubes for biobatteries and biofuel cells
PublikacjaSinglwalled carbon nanotubes (swcnts)covalently phenylated, napthylated or terphenylated were used for the construction of cathodes in a biobattery and in a biofuel cell. zn is the anode in the biobaterry and single-walled carbon nanotubes are covalently modified with glucose oxidase/catalase (swcnt-gox/cat) and the biofuel cell anode. the cell parameters were determined and the potentials of each of the electrodes under cell working...
-
Inline Waveguide Filter With Compact Frequency-Dependent Coupling Producing Two Additional Poles and Three Transmission Zeros
PublikacjaThis work reports a compact frequency-dependent coupling (FDC) structure introduced in a rectangular waveguide, which allows to generate two additional in-band transmission poles and three transmission zeros (TZs). This serves to increase the order/selectivity of the waveguide bandpass filter in a compact inline topology, thus without the need for any additional space/volume or cross coupling. The proposed FDC consists of a partial-height...
-
Highly-Compact Dual-Band Bandpass Waveguide Filter Based on Cross-Shaped Frequency-Dependent Coupling
PublikacjaThis work reports the design of an original class of highly-compact dual-band bandpass filter based on dual-mode waveguide resonators inter-coupled through a novel type of frequency-dependent coupling (FDC). The devised FDC consists of a cross-shaped metallic structure placed in the broad wall of a rectangular waveguide. This FDC produces two additional poles and three extra transmission zeros (TZs). Specifically, each pole is...
-
Review of Recent Advancement on Nature/Bio-inspired Antenna Designs
PublikacjaThis article presents an extensive examination of antennas rooted in nature and biology, showcasing their remarkable performance across a wide spectrum of frequencies—from microwave to terahertz. The limitations of traditional antenna design have become increasingly evident in the face of burgeoning demands for novel communication technologies. Conventional analytical-equation-based approaches struggle to deliver the combined performance...
-
Evaluation of Temperature Influence on Electrochemical Processes Occurring in a Lithium-Ion Supercapacitor with the Use of Dynamic Electrochemical Impedance Spectroscopy
PublikacjaIn order to obtain the full impedance characteristics of a lithium-ion capacitor as a function of temperature, the authors proposed the use of dynamic electrochemical impedance spectroscopy. Impedance tests were carried out under wide range of dynamic temperature changes for lithium-ion supercapacitors. Significant differences in electrochemical processes were observed as a result of working temperature. Moreover, the quality of...
-
A method of earth fault loop impedance measurement without unwanted tripping of RCDs
PublikacjaIn low-voltage networks, earth fault loop impedance (EFLI) measurement is the basis for assessing the effectiveness of automatic disconnection of supply. Such a measurement is performed during initial and periodical verification, especially in a TN low-voltage network. Nowadays, due to widespread application of residual current devices (RCDs), such test is difficult in many circuits because RCDs operate during the test. In this...
-
Symmetrical power line conditioner - basic properties
PublikacjaIn this paper the basis of analytical modelling of the UPQC arrangements (Unified Power Quality Conditioner) in d-q rotating coordinates, as well as select results of investigations conducted on the simplified small power laboratory model, were talked over. In short form power balance as well as fundamental dependences and analytical model with regard of decoupling circuits, were investigated. Applied method for DC link capacitance...
-
Modeling and experimental investigation of the small UPQC systems
PublikacjaIn this paper the basis of analytical modelling of the UPQC arrangements (Unified Power Quality Conditioner) in d-q rotating coordinates, as well as select results of investigations conducted on the simplified small power laboratory model were talked over. In short form power balance as well as fundamental dependences and analytic model with regard of decoupling circuits were investigated. Applied method for DC link capacity selection...
-
Analog fault signature based on sigma-delta modulation and oscillation-test methodology.
PublikacjaW artykule dokonano przeglądu prac z zakresu testowania układów elektronicznych metodą oscylacyjną. Wskazując na niedostatki aktualnie stosowanej techniki testowania oscylacyjnego zaproponowano nową sygnaturę uszkodzeń dla układów analogowych. Proponowany parametr diagnostyczny jest wydobywany z odpowiedzi czasowej oscylatora testującego, w układzie złożonym z detektora szczytowego, modulatora sigma-delta oraz licznika rewersyjnego....
-
Evidence for consolidation of neuronal assemblies after seizures in humans
PublikacjaThe establishment of memories involves reactivation of waking neuronal activity patterns and strengthening of associated neural circuits during slow-wave sleep (SWS), a process known as "cellular consolidation" (Dudai and Morris, 2013). Reactivation of neural activity patterns during waking behaviors that occurs on a timescale of seconds to minutes is thought to constitute memory recall (O'Keefe and Nadel, 1978), whereas consolidation...
-
A Compact Basis for Reliable Fast Frequency Sweep via the Reduced-Basis Method
PublikacjaA reliable reduced-order model (ROM) for fast frequency sweep in time-harmonic Maxwell’s equations by means of the reduced-basis method is detailed. Taking frequency as a parameter, the electromagnetic field in microwave circuits does not arbitrarily vary as frequency changes, but evolves on a very low-dimensional manifold. Approximating this low-dimensional manifold by a low dimension subspace, namely, reduced-basis space, gives...
-
Designing efficient A-D-A1-D-A type fullerene free acceptor molecules with enhanced power conversion efficiency for solar cell applications
PublikacjaThe achievement of highly efficient power conversion efficiency (PCE) is a big concern for non-fullerene organic solar cells (NF-OSCs) because PCE can depend on numerous variables. Here, new five novel acceptor molecules without fullerenes were developed and investigated using DFT (density functional theory) and TD-DFT (time dependent-density functional theory). Compared to the recently synthesized molecule (PZ-dIDTC6), the developed...
-
Microfluidic SIW-Based Tunable Self-Diplexing Antenna for Sub-6 GHz Band Applications
PublikacjaThis work introduces a novel frequency tunable self-diplexing antenna (SDA) design based on substrate integrated waveguide (SIW) technology. A modified A-shaped slot is employed on the cavity’s top plane, which is excited by two independent 50 Ω microstrip feed lines to operate at each resonant frequency. The frequency flexibility of the proposed antenna allows for fine-tuning at each resonance frequency. The frequency flexibility...
-
Shielded HMSIW-Based Self-Triplexing Antenna With High Isolation for WiFi/WLAN/ISM Band
PublikacjaThis article presents a novel design of a miniaturized self-triplexing antenna (STA) based on the shielded half-mode substrate integrated waveguide (S-HMSIW) for WiFi/WLAN/ISM-band applications. The S-HMSIW is constructed by assembling one row of vias and an open slot at the open-ended side of the conventional HMSIW. This configuration increases the quality factor and minimizes unwanted radiation loss, which allows for achieving...
-
Rapid multi-objective design of integrated on-chip inductors by means of Pareto front exploration and design extrapolation
PublikacjaIdentification of the best trade-offs between conflicting design objectives allows for making educated design decisions as well as assessing suitability of a given component or circuit for a specific application. In case of inductors, the typical objectives include maximization of the quality factor and minimization of the layout area, as well as maintaining a required inductance at a given operating frequency. This work demonstrates...
-
Regularized Local Multivariate Reduced-Order Models With Nonaffine Parameter Dependence
PublikacjaThis paper addresses a singular problem, not yet discussed in the literature, which occurs when parametric reduced-order models are created using a subspace projection approach with multiple concatenated projection bases. We show that this technique may lead to the appearance of localized artifacts in the frequency characteristics of a system, even when the reduced-order projection basis is rich enough to describe the original...
-
On the Dynamics of a Visco–Piezo–Flexoelectric Nanobeam
PublikacjaThe fundamental motivation of this research is to investigate the effect of flexoelectricity on a piezoelectric nanobeam for the first time involving internal viscoelasticity. To date, the effect of flexoelectricity on the mechanical behavior of nanobeams has been investigated extensively under various physical and environmental conditions. However, this effect as an internal property of materials has not been studied when the...
-
Vehicle detector training with labels derived from background subtraction algorithms in video surveillance
PublikacjaVehicle detection in video from a miniature station- ary closed-circuit television (CCTV) camera is discussed in the paper. The camera provides one of components of the intelligent road sign developed in the project concerning the traffic control with the use of autonomous devices being developed. Modern Convolutional Neural Network (CNN) based detectors need big data input, usually demanding their manual labeling. In the presented...
-
Experimental verification of visual method for measuring displacements of contact line elements
PublikacjaThe increase of rail vehicles speed, as well as the increase of their power, puts high demands on the power delivery system for traction vehicles The most critical point in the vehicle's power supply circuit is the contact between the current collector and contact wires. Ensuring a reliable co-operation of the current collector and contact line, requires technical development...
-
Design of Intelligent Low-Voltage Load Switch for Remote Control System in Smart Grid
PublikacjaCurrent low-voltage load switches do not support remote disconnect/connect and real-time monitoring of a disconnect/connect state. Addressing to these issues, this paper presents a low-voltage load switch for a smart remote control system, which uses a one-chip microcontroller board and a DC step motor drive mechanism and provides the feedback on the switch status also. Arrears disconnect and full-pay connect control is implemented...
-
Identification of the mechanical properties of the skin by electromechanical impedance analysis of resonant piezoelectric actuator
PublikacjaThis paper is devoted to the analysis and verification of developed piezoelectric sensor/actuator for measuring the mechanical properties of soft tissues, especially human skin. The key element of the measurement structure is an electromechanical system that uses both the reverse piezoelectric effect (vibration generation – stimulation of the tissues in the appropriate frequency range) and direct piezoelectric effect (system response...
-
Quality Evaluation of Agricultural Distillates Using an Electronic Nose
PublikacjaThe paper presents the application of an electronic nose instrument to fast evaluation of agricultural distillates differing in quality. The investigations were carried out using a prototype of electronic nose equipped with a set of six semiconductor sensors by FIGARO Co., an electronic circuit converting signal into digital form and a set of thermostats able to provide gradient temperature characteristics to a gas mixture. A volatile fraction...
-
Comparison of state feedback and PID control of pressurizer water level in nuclear power plant
PublikacjaThe pressurizer water level control system in nuclear power plant with pressurized water reactor (PWR) is responsible for coolant mass balance. The main control goal is to stabilize the water level at a reference value and to suppress the effect of time-varying disturbances (e.g. coolant leakage in primary circuit pipeline system). In the process of PWR power plant operation incorrect water level may disturb pressure control or...
-
Synchronous generator model taking into account the non-uniform saturation of the pole shoes
PublikacjaFor the evaluation of modern electric power systems with regard to their behavior, weight, and reliability a novel modeling and simulation tools have been developed. The paper presents circuit model of synchronous generator taking into account both the non-sinusoidal distribution of the stator and rotor winding, and non-uniform saturation of the pole shoes. This model is suitable for simulation of both salient and no-salient pole...
-
Common-Mode Voltage and Bearing Currents in PWM Inverters: Causes, Effects and Prevention
PublikacjaIn modern induction motor drives an increase of transistors' switching frequency and a decrease of switching times are the sources of some serious problems. The high dv/dt and the common mode voltage generated by the inverter PWM control results in the appearances of bearing currents, shaft voltages, motor terminal overvoltages, the decrease of motor efficiency, and electromagnetic interference. The aspects of common mode (CM)...
-
A 0.5 V Nanowatt Biquadratic Low-Pass Filter with Tunable Quality Factor for Electronic Cochlea Applications
PublikacjaA novel implementation of an analogue low-power, second-order, low-pass filter with tunable quality factor (Q) is presented and discussed. The filter feature is a relatively simple, buffer-based, circuit network consisting of eleven transistors operating in a subthreshold region. Q tuning is accomplished by injecting direct current into a network node, which changes the output resistance of the transistors and, as a result, modifies...
-
Design of Compact and Wideband Groove Gap Waveguide-Based Directional Couplers
PublikacjaThis paper proposes a compact cross-shaped groove gap waveguide structure for creating wideband and compact directional couplers with different coupling levels. Groove gap waveguide technology is applied to overcome fabrication challenges of printed and hollow waveguide structures in high frequency bands. The validity of the novel concept is demonstrated through the design and evaluation of several compact broadband directional...
-
Analiza przepływu gazu w kanałowych reduktorach ciśnienia podczas zwarć łukowych w rozdzielnicach SN
PublikacjaW artykule przedstawiono metodę obliczania ciśnienia i temperatury gazów podczas zwarcia łukowego wewnątrz przedziału wyłącznika rozdzielnicy średniego napięcia z wykorzystaniem modelu termodynamicznego procesów towarzyszących zwarciom łukowym wewnątrz rozdzielnic z izolacją powietrzną. Następnie, w oparciu o mechanikę płynów lepkich, przedstawiono metodę obliczania rozkładu prędkości i ciśnienia gazu w kanałowych reduktorach ciśnienia...
-
Wizyjny system monitoringu stanu nakładek stykowych odbieraków prądu
PublikacjaEksploatowane do niedawna w Polsce nakładki pantografów kolejowych były wykonywane w postaci styków miedzianych. Na początku 2011 r. przeprowadzono kompleksową zmianę typu nakładek stykowych, stosowanych przez operatorów korzystających z infrastruktury PKP PLK S.A., z miedzianych na metalizowane węglowe. Wraz z wprowadzeniem nakładek węglowych istnieje potrzeba opracowania nowych metod diagnostyki tego istotnego elementu toru zasilania...
-
Nowe rozwiązania metodyczne i techniczne w zakresie techniki mikroekstrakcji do fazy stracjonarnej
PublikacjaSample preparation has been recognized as a critical step of the analytical process, being even considered as the bottleneck of the overall process. Enrichment of target compounds, transfer of the analytes into a solvent compatible with the analytical instrumentation, minimization of potential interferences, and efficient sample clean-up, are among the main aims of sample preparation techniques. In this regard, liquid-liquid extraction...
-
Solventless and solvent-minimized sample preparation techniques for determining currently used pesticides in water samples: A review
PublikacjaThe intensification of agriculture means that increasing amounts of toxic organic and inorganic compounds are entering the environment. The pesticides generally applied nowadays are regarded as some of the most dangerous contaminants of the environment. Their presence in the environment, especially in water, is hazardous because they cause human beings to become more susceptible to disease. For these reasons, it is essential to...
-
Conception and design of a hybrid exciter for brushless synchronous generator. Application for autonomous electrical power systems = Koncepcja i projekt hybrydowej wzbudnicy bezszczotkowego generatora synchronicznego. Zastosowanie w autonomicznych systemach elektroenergetycznych
PublikacjaIn this paper a hybrid excitation system for a brushless synchronous generator working with variable speed in an autonomous energy generation system (e.g. airplane power grid) has been presented. A conception of a dual-stator hybrid exciter has been proposed. Comparison study of classical and hybrid exciter has been carried out. For the electromagnetic calculation two approaches have been applied: an analytical approach (based...
-
Cross-Bonding of MV Cable Lines for Energy Losses Decrease
PublikacjaCurrently, almost all medium voltage cable lines (MV) operate with the return wires earthed at both ends of the cable. Such a way of operation causes that during normal states of operation as well as during disturbances, e.g. short-circuits, in the return wires induce currents whose values mainly depend on the currents flowing in the phase wires. These currents in normal operating states are a source of additional energy losses...
-
Fault-tolerant performance of the novel five-phase doubly-fed induction generator
PublikacjaThe article presents the concept of a new design of a multi-phase doubly-fed induction generator (DFIG). The innovative design approach uses a five-phase power supply from the rotor side of the generator with a three-phase classic stator power supply. Modern three-phase doubly-fed induction generators are the dominant choice for Wind Energy Conversion Systems (WECS). Solutions of this type are sensitive to the loss of at least...