Wyszukiwarka
Filtry
wszystkich: 1066
wybranych: 863
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: FLUIDIC POCKETS
-
Modelowanie przepływu oleju pomiędzy klockami wzdłużnego łożyska ślizgowego
PublikacjaW pracy przedstawiono model MES wzdłużnego łożyska ślizgowego, wykonany przy pomocy programu ANSYS. Prezentowany model umożliwia badanie przypadków smarowania zanurzeniowego oraz smarowania wymuszonego. Przedstawiono korzyści stosowania technik CFD (Computational Fluid Dynamic) pozwalających na obserwację ruchu oleju pomiędzy klockami łożyska ślizgowego w przypadku nietypowych konstrukcji systemów smarowania.
-
Free-surface elevation in open vortex flow controls
PublikacjaRotational form of fluid motion is complex, but very important in science and technology. The paper is devoted to the hydraulic mechanism of flow in open vortex flow controls, or regulators. The velocity field was described by the kinematic model, and intensity of rotation - by means of the energy balance between the input and dissipation. In consequence some algebraic expresions were obtained, which can be useful in approximated...
-
A novel concept of enhanced direct-contact condensation of vapour- inert gas mixture in a spray ejector condenser
PublikacjaAn analytical model of direct steam condensation (DCC) in the novel idea of spray ejector condenser (SEC) in the presence of inert gas has been developed. It is based on continuity, momentum and energy equations for the steam-carbon dioxide mixture and direct contact condensation mechanisms due to heat transfer and concentration. Crucial in the process of DCC is atomisation of the motive fluid in the ejector. The effect of atomised...
-
Influence of concentration on contact angle of water-Cu nanofluid on glass substrate
PublikacjaIn the paper the results of an experimental investigation of influence of nanoparticle concentration on contact angle of water-Cu nanofluid on glass substrate have been presented. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight. In the present study copper was applied as nanoparticle while distilled, deionized water was used as a base fluid. The mean diameter of nanoparticle is estimated to be 50...
-
Analysis of different tillage implements with respect to reduced fuel consumption, tractor operating speed and its wheel slippage
PublikacjaNowadays the prices of agricultural farm produced products are increasing with ant-speed and the prices of input for raising crops are increasing with rocket-speed. Therefore, there is a dire need to conduct some important studies to innovate the techniques which can lower the costs of crop production. In this context, this study was conducted to evaluate the consumption of fuel at different tillage implements, tractor operating...
-
System zabezpieczenia emerytalnego a starzenie się społeczeństwa w Polsce.
PublikacjaNowy porządek demograficzny w Polsce będący m.in. efektem drugiego przejścia demograficznego, nawiązuje do przemian wzorca płodności (spadek liczby urodzeń, opóźnienie momentu podjęcia decyzji odnośnie posiadania dzieci oraz przesunięcie dominanty wieku rodzenia). Proces odtwarzania pokoleń utrzymuje się tym samym na poziomie poniżej prostej zastępowalności pokoleń. Zmianom tym towarzyszy nieprzerwanie wydłużanie się ludzkiego...
-
Pressure drop related to flow maldistribution in a model minichannel plate heat exchanger
PublikacjaThe paper describes the issues related to the pressure drop that accompanies the phenomenon of maldistribution of working fluid between the channels of a model minichannel plate heat exchanger. The research concerns a single exchanger's plate containing 51 (in every geometry) parallel rectangular minichannels of hydraulic diameters 461 µm, 571 µm, 750 µm and 823 µm. In addition, the more complex geometry has been investigated,...
-
Experimental Verification of the CFD Model of the Squeeze Film Lifting Effect
PublikacjaAbstract: The presented study shows the results of the research into the squeeze film levitation phenomena. The system introduced in the investigation is composed of a vibrating surface, air squeeze film, and the surface of the body freely suspended over the film. The use of the CFD (Computational Fluid Dynamics) model used in the system allows us to determine the steady state, periodic behavior of the air film (described by Navier–Stokes,...
-
Teoretyczno-doświadczalne modelowanie konwekcji wymuszonej nanocieczy
PublikacjaPrzedłożona rozprawa doktorska dotyczy badań eksperymentalnych oraz numerycznych konwekcji wymuszonej nanocieczy. Badane nanociecze wytworzone były z cieczy bazowych takich jak woda demineralizowana i mieszaniny wody z glikolem etylenowym w trzech proporcjach objętościowych 90:10, 80:20 i 60:40. Jako nanocząstki użyto Al2O3, a wytworzone nanociecze miały koncentracje masowe 0,1%, 1% i 5%. Wyznaczono eksperymentalnie dynamiczny...
-
Flow Maps and Flow Patterns of R1233zd(E) in a Circular Minichannel at Low, Medium and High Values of Saturation Pressure
PublikacjaThere is a gap in knowledge regarding the flow pattern of low-boiling working fluids in the range of high saturation temperatures (above 120°C) and medium and high reduced pressures (0.5-0.9). Data are present in the literature for similar values of reduced pressures, but for lower values of saturation temperature. This is due to the existing refrigeration applications of these working fluids. At high values of reduced pressure,...
-
The compositional space of exhaled breath condensate and its link to the human breath volatilome
PublikacjaBreath analysis is commonly understood to target gaseous or volatile organic compounds (VOCs) for the characterization of different pathologies. Targeted analysis is most effective if a working hypothesis can be based on a plethora of data. The recently published volatilome builds an optimal basis for organizing powerful target sets. However, the origin and pathways of biosynthesis of many VOCs are not known, which complicates...
-
Assessment of toxic and endocrine potential of substances migrating from selected toys and baby products
PublikacjaAnalysis of literature data shows that there is limited information about the harmful biological effects of mixture of compounds from the EDC group that are released from the surface of toys and objects intended for children and infants. One of the tools that can be used to obtain such information is appropriate bioanalytical tests. The aim of this research involved determining whether tests that use living organisms as an active...
-
Tesla Friction-Type Micro Turbine For Small-Scale Cogeneration
PublikacjaTesla turbine is rarely used in professional power installations due to its specific work characteristics and relatively low internal efficiency. However, it has some potential to be applied in micro-power plants operating in distributed co-generation systems, also working in an organic Rankine cycle. This paper presents results from numerical calculations of flow in three models of Tesla disk turbines assuming nitrogen as a working...
-
THE POSSIBILITY OF USE OF LASER-MODIFIED Ti6Al4V ALLOY IN FRICTION PAIRS IN ENDOPROSTHESES
PublikacjaThe purpose of this paper is to show results of laser treatment at cryogenic conditions of the Ti6Al4V alloy used for orthopedic applications. That modification process ought to bring beneficial changes of microstructure and residual stresses in the surface layer. The paper presents the abrasive wear of the base and laser remelted material in association with ceramics Al2O3. Despite the surface cracking after laser treatment the...
-
Wykorzystanie tomografii komputerowej przy analizie jakości zacementowania - migracja gazu
PublikacjaArtykuł przedstawia opis zjawiska znanego w wiertnictwie otworowym jako migracja gazu. Opisano główne przyczyny powstawania tego negatywnego zjawiska polegającego na przepływie gazów a także płynów w zaczynie cementacyjnym lub kamieniu cementowym. Przygotowano próbki imitujące zacementowany odcinek rur okładzinowych. Skupiono się na wykorzystaniu tomografii komputerowej, oraz analizie zrekonstruowanego trójwymiarowego obrazu, w...
-
Performance of the flat plate solar collector operated with water-Al2O3 nanofluid
PublikacjaThis paper shows the experimental results of the performance a flat plate solar collector with water-Al2O3 nanofluid as a working fluid. The weight fractions of nanoparticles were 0.1%, 0.2% and 0.4%. The volume flow rate of nanofluid varied from 60 l/h to 170 l/h. The results show that application of nanofluids instead of pure water resulted in higher efficiency of the tested flat plate solar collector for given range of thermal...
-
Thermal Self-Action of Acoustic Beams Containing Several Shock Fronts
PublikacjaThermal self-action of an acoustic beam with one discontinuity or several shock fronts is studied in a Newtonian fluid. The stationary self-action of a single sawtooth wave with discontinuity (or some integer number of these waves), symmetric or asymmetric, is considered in the cases of self-focusing and self- defocusing media. The results are compared with the non-stationary thermal self-action of the periodic sound. Thermal self-action...
-
Cyanides in the environment—analysis—problems and challenges
PublikacjaCyanide toxicity and their environmental impact are well known. Nevertheless, they are still used in the mining, galvanic and chemical industries. As a result of industrial activities, cyanides are released in various forms to all elements of the environment. In a natural environment, cyanide exists as cyanogenic glycosides in plants seeds. Too much consumption can cause unpleasant side effects. However, environmental tobacco smoke...
-
Studies of the Interaction Dynamics in Albumin-Chondroitin Sulfate Systems by Recurrence Method
PublikacjaThe physicochemical basis of lubrication of articular cartilage is still not fully understood. However, the synergy between components of the synovial fluid can be a crucial factor that could explain this phenomenon. This work presents a nonlinear data analysis technique named the recurrence method, applied to the system involving two components of synovial fluid: albumin and chondroitin sulfate (CS) immersed in a water environment....
-
The thermal effort during marine steam turbine flooding with water
PublikacjaThe work discussed an extreme case of cooling a steam turbine. The ship's steam turbine was used as an example. In marine transport units with low-speed engines dominate, however, there are also units with steam turbines. An example of analysed marine steam turbine is shown in Fig. 1. When considering the issue of cooling steam turbines, it is necessary to estimate the extreme conditions that may occur during operation of the turbine....
-
The Processing Procedure for the Interpretation of Microseismic Signal Acquired from a Surface Array During Hydraulic Fracturing in Pomerania Region in Poland
PublikacjaHydraulic fracturing is a procedure of injecting high pressure fluid into the wellbore in order to break shell rock and facilitate gas flow. It is a very costly procedure and, if not conducted properly, it may lead to environmental pollution. To avoid costs associated with pumping fluid outside the perspective (gas rich) zone and improve one’s knowledge about the reservoir rock, microseismic monitoring can be applied. The method...
-
A novel in vivo approach to assess strains of the human abdominal wall under known intraabdominal pressure
PublikacjaThe study concerns mechanical behaviour of a living human abdominal wall. A better mechanical understanding of a human abdominal wall and recognition of its material properties is required to find mechanically compatible surgical meshes to significantly improve the treatment of ventral hernias. A non-invasive methodology, based on in vivo optical measurements is proposed to determine strains of abdominal wall corresponding to...
-
Effect of Ion and Binding Site on the Conformation of Chosen Glycosaminoglycans at the Albumin Surface
PublikacjaAlbumin is one of the major components of synovial fluid. Due to its negative surface charge, it plays an essential role in many physiological processes, including the ability to form molecular complexes. In addition, glycosaminoglycans such as hyaluronic acid and chondroitin sulfate are crucial components of synovial fluid involved in the boundary lubrication regime. This study presents the influence of Na+, Mg2+ and Ca2+ ions...
-
Deformable model of a butterfly in motion on the example of Attacus atlas
PublikacjaInsect wings can undergo significant chordwise (camber) as well as spanwise (twist) deformation during flapping flight but the effect of these deformations is not well understood. The shape and size of butterfly wings leads to particularly large wing deformations, making them an ideal test case for investigation of these effects. High-speed videogrammetry was used to capture the wing kinematics and deformations. The movements of...
-
Computer animation system based on rough sets and fuzzy logic
PublikacjaA fuzzy logic inference system was created, based on the analysis of animated motion features. The objective of the system is to facilitate the creation of high quality animation by analyzing personalized styles contained in numerous animations. Sequences portraying a virtual character acting with a differentiating personalized style (natural or exaggerated) and various levels of fluidity were prepared and subjectively evaluated....
-
Instantaneous Heating and Cooling Caused by Periodic or Aperiodic Sound of Any Characteristic Duration in a Gas with Vibrational Relaxation
PublikacjaThermodynamic relaxation of internal degrees of a molecule's freedom in a gas occurs with some characteristic time. This makes wave processes in a gas behave differently depending on the ratio of characteristic duration of perturbations and the relaxation time. In particular, generation of the secondary non-wave modes by intense sound in a nonlinear flow dependens on frequency. These kinds of interaction are considered in this...
-
Hysteresis curves for some periodic and aperiodic perturbations in gases
PublikacjaEvolution of sound in a medium whose properties irreversibly vary in the course of wave propagation, is studied. For example, a gas that is a particular case of a Newtonian fluid is considered. Hysteresis curves, pictorial representations of irreversible attenuation of the sound energy, in the plane of thermodynamic states are plotted. The irreversible losses in internal energy are proportional to the total attenuation and depend...
-
Thermal Self-Action Effects of Acoustic Beam in a Gas with Reversible or Irreversible Chemical Reaction
PublikacjaThermal self-action of acoustic beam in a gas where an exothermic chemical reaction takes place, is studied. This kind of thermal self-action differs from that in a newtonian fluid. In dependence on the type of a chemical reaction, reversible or not, heating or cooling of a medium occurs. A beam in the case of the irreversible reaction may be unusually self-focusing. The self-action effects relating to wave beams containing shock...
-
Experimental and theoretical study of surface cooling using a single microjet
PublikacjaPrzedstawiono wyniki badań eksperymentalnych intensyfikacji wymiany ciepła przy pomocy pojedynczych strug wody i powietrza.Uzyskana na podstawie wyników korelacja, opisująca współczynnik przejmowania ciepła, posłużyła do weryfikacji modelu opracowanego wcześniej przez Mikielewicza (2007).
-
HIERARCHICAL CYCLES IN MODERN POWER SYSTEMS – EXERGY ANALYSIS UNDER PART LOADS
PublikacjaThe aim of the paper is to investigate thermodynamic efficiency of advanced hierarchic power cyclesunder partial loads by using of exergy analyze. Advanced hierarchical power systems arecomposed of few energy conversion cycles, most common are steam and gas cycles in various configurations, but they may contain fuel cells, ORC, lithium bromide absorption chillers and others. Moreover hierarchical cycles can be powered by several...
-
An advanced thermal-FSI approach of an evaporation of air heat pump
PublikacjaThe paper presents selected problems of numerical modeling of an advanced thermal-FSI approach of evaporator of air heat pomp. The example of a fin-tube evaporator has been studied, focusing on obtaining of heat exchanger characteristics applying two-phase flow model for the in-tube refrigerant flow. Special attention is given to heat transfer between separated medium for different air velocity and changed refrigerant mass flow...
-
ENHANCED EVAPORATION OF THE DROPLETS OF CONDENSATE IN THE ASYMMETRICAL SHOCK WAVE ZONE
PublikacjaIn the low-pressure part of steam turbine, the state path usually crosses the saturation line in penultimate stages [4,5]. The formation and evolution of these droplets lower the performance of the wet stages of the turbines, and their effects on the efficiency are collectively known as wetness losses [4]. Nowadays, due to work of steam turbines at partial load, process of homogeneous and heterogeneous condensation still is current....
-
Estimation of the steam condensation flow via CFD methods
PublikacjaThe results of numerical simulations to predict the performance of different steam models have been presented. All of the considered models of steam condensation have been validated on the base of benchmark experiment employing expansion in nozzle and next on the low pressure part of the steam turbine stage. For numerical analysis three models have been finally used – the ideal steam model without condensation, an equilibrium steam...
-
INFLUENCE OF SURFACE CURVATURE ON SESSILE DROPLET CONTACT ANGLE OF NANOFLUIDS
PublikacjaThis paper deals with change in contact angle of droplets of three nanofluids, i.e. water-Al2O3, water-TiO2 and water-Cu. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight. Although dispersants were not used to stabilize the suspension, the solutions tested exhibited satisfactory stability. Ultrasonic vibration was used in order to stabilise the dispersion of the nanoparticles. Experimental measurements...
-
On the internal efficiency of a turbine stage: classical and CFD definitions
PublikacjaAlmost entire fleet of steam turbines in Poland was designed between 1950 – 1980 with the use of the so-called zero dimensional (0D) calculation tools. For several years, design and modernization of the turbines occur in assistance with the state of the art methods that describe working fluid flow field based on 3D models and CFD codes. This cooperation between 0D and 3D codes requires exchange of overall, integral information...
-
Clean gas technologies - towards zero-emission repowering of Pomerania.
PublikacjaThe main aim this work is to show the different thermodynamic cycles which improve efficiency and/or decrease emission like: Cheng cycle, Szewalski cycle, LOTHECO cycle, hybrid pSOFC/GT cycle, inverse Brayton cycle, low-emission cycle and zero-emission cycle. For that purpose, cycles and results of analysis are first studied and, secondly, new concept is presented. The role of coupled analysis 0D and 3D in cycle’s devices is also...
-
Design and distribution of air nozzles in the biomass boiler assembly
PublikacjaDue to energy crisis as well as increasing pollution of the environment, renewable energy sources usage increases all over the world. These facts encouraged authors to start research over developing a uniform biomass boiler calculation model. This paper presents a design of biomass boiler assembly created for ORC (Organic Rankine Cycle) unit since these systems could achieve strong position in energy industry....
-
Enhancement of the Brayton cycle efficiency by water or steam utilization
PublikacjaIn the paper, thermodynamic analysis of two modifications of a Brayton cycle into enhancement cycles with water/steam injection are discussed. The first one deals with a STIG modified system with both interstage compressed air cooling and air heating (heat regeneration) before combustion chamber. The second one, mainly devoted to higher steam/air ratio, is connected with separate steam production in a HRSG. The analysis has been...
-
Investigation of R 22 and R 134a flow boiling in enhanced tubes
PublikacjaPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła i spadków ciśnienia podczas wrzenia w przepływie R22 oraz R134a. Do badań użyto dwie rurki o rozwiniętej wewnętrznej powierzchni, tj. rurkę śrubowo-formowaną i rurkę niskożebrowaną oraz dwie rurki gładkie, jako rurki referencyjne. Eksperymenty przeprowadzono przy temperaturze nasycenia ok. zero stopni Celsjusza i końcowym stopniu suchości ok. 0.7. Wyniki badań eksperymentalnych...
-
Influence of gas parameters alteration on the form of gas-flow-impact appearing in long transportation pipelines
PublikacjaPrzy szybkich zamknięciach przepływu w długich liniach transportowych gazu, obserwuje się znaczne przesterowania ciśnienia, towarzyszące zjawiskom udarowym, wywołane zarówno falą uderzeniową jak i odbitą. Głównym czynnikiem wpływającym na postać fali uderzeniowej i jej amplitudy, jest szybkość zamykania zaworu odcinającego określona stałą czasową serwomotoru sterującego zaworem. Ponieważ obserwuje się zmiany właściwości chemicznych...
-
Experimental investigations of hydraulic jump created by a two-phase impin-ging jet on a solid surface
PublikacjaPrzedstawiono rezultaty badań eksperymentalnych powstawania uskoku hydraulicznego tworzonego przez dwufazową strugę uderzającą.
-
Theoretical investigations into flows in rotor blade shroud clearance
PublikacjaPrzedstawiono wyniki obliczeń programem Fluent przepływów w uszczelnieniu nadbandażowym stopnia turbinowego przy różnym mimośrodowym położeniu osi wirnika względem osi korpusu. Wyznaczone numerycznie rozkłady ciśnienia w uszczelnieniu i generowane tam siły aerodynamiczne porównano z rezultatem badań przeprowadzonych na powietrznej turbinie modelowej.
-
Analysis of transient heat transfer operation in tube wall.Selected papers from the International Conference on Turbines of Large Output devoted to 100th Anniversary of Prof. Robert Szewalski Birthday.
PublikacjaW pracy przedstawiono zachowanie się wymiennika ciepła stosowanego w układzie regeneracji turbin parowych w niestacjonarnych warunkach pracy.
-
An impact of ambient parameters change on steam and gas turboset control. The International Conference on ''Turbines of Large Output'' devoted to 100th Anniversary of prof. Robert Szewalski Birthday.
PublikacjaPorównano wpływ zmian parametrów otoczenia (ciśnienia i temperatury) na charakterystyki turbiny parowej i gazowej. Na tej podstawie zbadano wpływ tych parametrów na charakterystyki układu kombinowanego parowo-gazowego. Przedstawiono, w związku z tym, koncepcję kompensatora wpływu zmian parametrów otoczenia na charakterystyki układu kombinowanego parowo-gazowego.
-
On Application of Selected Methods of Artificial Intelligence in Expert Systems for Thermal and Flow Diagnostics
PublikacjaPrzedyskutowano problem wspomagania przez systemy ekspertowe decyzji eksploatacyjnych służb nadzoru obiegów turbin parowych. Uwagę skupiono na realizacji jednego z zadań tych systemów, polegającemu na określenie rozmiaru eksploatacyjnej degradacji parametrów geometrycznych układów łopatkowych turbin. Dyskusję przeprowadzono na przykładzie jednego z komponentów metod sztucznej inteligencji: wybranego typu sztucznej sieci neuronowej...
-
Volute scroll as an alternative to guide vanes at inlet to turbine.
PublikacjaW pracy przedstawiono alternatywny sposób zasilania turbin parowych poprzez zastosowanie podwójnej spirali zasilającej. Przedstawiono model jednowymiarowy obliczania przepływu przez spirale oraz zamieszczono wyniki obliczeń typu 3D. Pokazano jak zależy parametr nierównomierności rozkładu prędkości na wylocie od sposobu kształtowania przekroju spiral.
-
STUDY ON THE EFFECTIVENESS OF THE TURBINE CONDENSER AIR EXTRACTION SYSTEM USING HYDRO EJECTORS
PublikacjaThe aim of the paper is to investigate the effectiveness of the 18K380 steam turbine condenser air extraction system using hydro ejectors. Motivation for the analysis is a need of improvement of the energy conversion ratio of the power plant. To achieve this goal it is necessary to establish efficiency of each subsystem of the energy cycle. The air extraction system is not a highly power consuming system but it has great impact...
-
A role of the heat and work uncompensatedtransformations in the balance of entropy and theturbomachinery efficiency
PublikacjaIn the paper we have presented a procedure of estimating a role of the uncompensated transformation of heat and work in ow of viscous and heat conducting uid. The procedure was introduced by Professor Romuald Puzyrewski and is essential in local, in time and space, balance of entropy. Furthermore this unique approach leads to redenition the eciency of uid-ow machinery in three-dimensional modeling using CFD (Computational Fluid...
-
Kinetic analysis of the stage for a high speed steam turbine
PublikacjaThis article analyzes possibilites of resonances within a control stage for a high speed steam turbine. This stage hase been based on assembling of a single blade to a rotating disk and increasing of rigidity of the system by using of a bandage. In the analysis will be nd a possiblity of resonance frequency, and mistuning by showing safety working ranges. The calculations have bean used the3D modal and harmonic analysis by the...
-
How much a geometrical model of a honeycomb seal can be simpli ed in the CFD calculation
PublikacjaThis paper presents the inuence of geometry simplication on the results obtained in the computational fluid dynamics simulation. The subject of simulation was part of the honeycomb seal located at the inlet to high pressure part of a steam turbine. There were three different geometrical models assumed in the calculations. First one was two-dimensional case and two others were three dimensional, one with the radius of curvature...