Filtry
wszystkich: 1209
wybranych: 934
Wyniki wyszukiwania dla: SHANNON CAPACITY
-
Vibro piles performance prediction using result of CPT
PublikacjaVibro piles belong to the group of full displacement piles with an expanded base, characterised by a very high load capacity, especially in non-cohesive soils. The problem is to adopt a reliable method for the determination of full load–settlement (Q–s) curve. A frequent difficulty is the determination of the load capacity limit based on the static load test because the course of the load–settlement curve is of a linear nature....
-
Zagrożenie katastrofą budowlaną Mostu Uniwersyteckiego w Bydgoszczy. Analiza i badania
PublikacjaMost Uniwersytecki został zamknięty po 7 latach od oddania do użytku. Powodem były błędy projektowe ujawnione w przeglądzie w roku 2020, potwierdzone teoretycznymi analizami nośności. Bezpośrednim powodem zamknięcia przeprawy było stwierdzenie zagrożenia katastrofą budowlaną. W roku 2021, zgodnie z zaleceniem i koncepcją ekspercką, krytyczne elementy konstrukcji mostu zostały wzmocnione. W styczniu 2022 most został przywrócony...
-
The electronic characterization of the cubic Laves-phase superconductor CaRh2
PublikacjaWe present the synthesis and experimental characterization of the electronic properties of the cubic Laves phase superconductor CaRh2. Its crystal structure was confirmed by powder X-ray diffraction and its ambient temperature lattice parameter (a = 7.5326(6) Å) is in good agreement with the literature. Magnetization, resistivity and heat-capacity measurements indicate that CaRh2 is a moderate-coupling type-II superconductor (λe-p = 0.89)...
-
Implementacja pomierzonych imperfekcji geometrycznych powłokicylindrycznej do modelu obliczeniowego
PublikacjaThis paper presents the method of implementation of the geometrical imperfections used by the author during the experimental and numerical research into the load-carrying capacity of cylindrical steel shells subjected to uniform circumferential compression.
-
Investigation and operation problems of metal tanks in Poland
PublikacjaThe paper consists of three parts concerned with steel cylindrical, vertical tank for liquid fuel. In the first part the present trends in tank design and building in Poland are described. The main are: · reduction of environment contamination danger caused by tank leakage and hydrocarbons evaporation, · increasing capacity of new tanks (100000 m3 and more) due to economic factor - reduction of steel amount per m3 of storage capacity....
-
New ceramic materials derived from pyrolyzed poly(1,2-dimethylsilazane) and starch as a potential anode for Li-ion batteries
PublikacjaNewmaterialswere obtained by pyrolysis of starch (S) and poly(1,2-dimethylsilazane) (PSN) (weight ratio: PSN/S 30/70) at temperature a) 500 °C, b) 700 °C and c) 900 °C. Ceramic materials were characterized by infrared spectroscopy, TGA, Raman spectroscopy and SEM. New Si\O and shifted Si\C stretching vibration modes emerged confirming direct interaction between silicon originating fromsilazane and oxygen coming fromstarch. The...
-
Novel methods for diagnosis of pulmonary microangiopathy in diabetes mellitus
PublikacjaLung microangiopathy is a little known negative influence of diabetes mellitus on the functioning of the lungs. In current medical practice lung microangiopathy is diagnosed by comparing two measurements of lung diffusing capacity - one with the subject standing and one with the subject lying. The necessity to take two measurements is inconvenient. In lung microangiopathy we observe a reduction of diffusing capacity, lung flow...
-
Thermodynamic Characteristics of Phenacetin in Solid State and Saturated Solutions in Several Neat and Binary Solvents
PublikacjaThe thermodynamic properties of phenacetin in solid state and in saturated conditions in neat and binary solvents were characterized based on differential scanning calorimetry and spectroscopic solubility measurements. The temperature-related heat capacity values measured for both the solid and melt states were provided and used for precise determination of the values for ideal solubility, fusion thermodynamic functions, and...
-
Characterization of 1,3-alternate calix[4]arene-silica bonded stationary phases and their comparison to selected commercial columns by using principal component analysis
PublikacjaTwelve calix[4]arene stationary phases in 1,3-alternate conformation, synthesized in the authors laboratory, were characterized in terms of their surface coverage, hydrophobic selectivity, aromatic selectivity, shape selectivity, hydrogen bonding capacity and ion-exchange capacity. The set of tests commonly used for evaluation of commercially available stationary phases was applied to assess fundamental chromatographic properties...
-
ANALIZA PRZEPUSTOWOŚCI WYBRANEGO UKŁADU TOROWEGO W PRZESTRZENI CZĘŚCIOWO – UPORZĄDKOWANEJ
PublikacjaNa sieci kolejowej istotny wpływ na płynność ruchu mają odpowiednio usytuowane odcinki odstępowe. Z podobną sytuacją mamy do czynienia przy modernizacji stacji kolejowych i tworzeniu nowych rozwiązań, w których należy uwzględnić prognozy rozwoju ruchu na danym elemencie sieci kolejowej. Jednak w przypadku stacji sytuacja staje się dużo bardziej skomplikowana i kosztowna, gdyż poprawa przepustowości wymaga istotnych zmian organizacyjnych...
-
Hard carbon derived from rice husk as low cost negative electrodes in Na-ion batteries
PublikacjaHere, we report the synthesis of hard carbon materials (RH) made from natural rice husk through a single pyrolysis process and their application as an anode in sodium-ion batteries. The studies show that the electrochemical properties of RHs are affected by the treatment temperatures, which determine the materials morphology, in particular, their degree of graphitization and extent of continuous channels (nanovoids). The latter...
-
Report of Eurocode 7 application for pile foundation design in Poland
PublikacjaThe EC7 rules of geotechnical design are in use in Poland for several years, even though there is no National annex. With regard to pile foundations, there are valid EC7 recommendations concerning design approaches, load partial coefficients, correlation coefficients and capacity partial coefficients. Polish designers can be quite flexible when it comes to choose a method for static, bearing capacity and settlement calculations....
-
Effective Short -term Forecasting of Wind Farms Power
PublikacjaForecasting a specific wind farm's generation capacity within a 24 hour perpective requires both a reliable forecast of wind, as well as supporting tools. This tool is a dedicated model of wind farm power. This model should include not only general rules of wind to mechanical energy conversion, but also the farm's specific features. This paper present analytical, statistical, and neuron models of wind farm power. The study is based...
-
Wykorzystanie metod symulacyjnych w modelowaniu morsko – lądowych łańcuchów dostaw na przykładzie DCT
PublikacjaArtykuł jest kolejnym etapem badań w zakresie modelowania lądowo – morskich łańcuchów dostaw. Badania miały na celu sprawdzenie płynności operacyjnej w terminalu kontenerowym na podstawie symulacji ruchu jednostek w założonym czasie z wykorzystaniem metody Monte Carlo. Płynność operacyjna terminalu była badana w oparciu o wskaźnik zajętości placu składowego przy założonych początkowych poziomach wypełnienia placu oraz zapotrzebowanie...
-
Rapana venosa consumption improves the lipid profiles and antioxidant capacities in serum of rats fed an atherogenic diet
PublikacjaIn the recent years, the consumption of seafood has increased. There are no results on the studies of Rapana venosa (Rv) as a supplementation to the diets. We hypothesized that Rv would increase antioxidant capacity and reduce blood lipids, based on the composition of bioactive compounds and fatty acids. Therefore, the aim of this investigation was to evaluate in vitro and in vivo actions of Rv from contaminated (C) and non-C (NC)...
-
The Impact of EU Funds on the Development of Business Environment Institutions – Research Results in Pomeranian Voivodeship in Poland
PublikacjaThe paper presents the main findings of the research conducted to assess the impact of EU funds on development of business environment infrastructure in Pomeranian Voivodeship in Poland, and – indirectly – on the growth of the innovation capacity of Pomeranian entrepreneurs. The research shows that support of ROP PV 2007-2013 contributed to the creation of multifunctional business infrastructure throughout the Pomorskie Voivodship,...
-
The influence of accumulation area and the length of pedestrian route on functioning of roundabouts with traffic signals
Publikacjatraffic volumes. This kind of intersection is commonly used in the centres of Polish cities on multilane roads and fairly common in the case of tram lines running through a central island. The increase of traffic flow volumes on left turn and U-turn has made this type of roundabout difficult to operate. Small storage areas around central islands are critical places that significantly influence the capacity of this kind of intersection....
-
ACTIVATED BIOCHAR AS AN ADSORBENT OF ORGANIC POLLUTANTS FOR WATER AND WASTEWATER TREATMENT
PublikacjaThe use of biomass, especially waste biomass, as an alternative energy source is a very important issue today. Pyrolysis is a process of thermal degradation of raw material and one of its products is biochar. This product is mainly distinguished by its high carbon content, and by improving its quality through activation, it can be more widely used. Activated biocarbon has a strongly developed surface and porous structure, and as...
-
Advanced super-hydrophobic polymer-based porous absorbents for the treatment of oil-polluted water
PublikacjaThe threat of environmental pollution caused by spilled oil is rapidly increasing along with the expansion of oil exploration, the development of maritime activities and industrial growth. Oil spill incidents usually affect seriously the ecosystem and human life. Therefore, the treatment and recovery of the oil spill have been considered as an ultra-important issue to protect the environment and to minimize its negative impacts...
-
Structural Reliability Assessment Of Corroded Tanker Ship Based On Experimentally Estimated Ultimate Strength
PublikacjaThis work deals with the reliability assessment of a tanker ship hull structure subjected to a vertical bending moment and corrosion degradation. The progressive collapse and ultimate load carrying capacity are estimated based on experimentally tested scaled box-shaped-specimens. The translation of the strength estimate of the scaled specimen to the real tanker ship hull structure is performed based on the dimensional theory developing...
-
Analysis and evaluation of grouping methods for effective cutting tool operation
PublikacjaThis article presents the possibilities for using cluster analysis in the assignment of machine tools in automated manufacturing systems. Based on the similarity of manufacturing processes in the system, cutting tools have been grouped. The objective was to obtain groups of similar objects, which could potentially ensure the reduction of the frequency and time of setups, optimizing the maintenance of tool resources and improving...
-
Modular power converter topologies for energy storage and electric power distribution systems
PublikacjaThis paper describes selected issues concerning realization of energy storage system (ESS) designed to operate in power distribution system. In order to achieve scalability of the system a modular approach is proposed. In addition to this different configuration of the system are analyzed, where depending on requirements and application a scalability in power, in energy capacity of energy storage resource and both in power and...
-
Soft – Partial Frequency Reuse Method for LTE-A
PublikacjaIn the paper a novel SPFR frequency reuse method is proposed which can be used for improvement of physical resources utilization efficiency in LTE-A. The proposed method combines both SFR and PFR giving the possibility of more flexible use of frequency band in different regions of a cell. First, a short study on the problem of frequency reuse in cells is discussed including bibliography overview....
-
Nano Tin/Tin Oxide Attached onto Graphene Oxide Skeleton as a Fluorine Free Anode Material for Lithium-Ion Batteries
PublikacjaHerein, we show a composite formation method of tin/tin oxide nanoparticles with graphene oxide and CMC based on laser ablation technique as an electrode material for energy storage devices. The material exhibited a three-dimensional conducting graphene oxide network decorated with tin or tin oxide nanoparticles. The structure, homogeneous distribution of nanoparticles, and direct contact between inorganic and organic parts were...
-
Wpływ imperfekcji geometrycznych na bezpieczeństwo montażu i naprawy zbiorników cylindrycznych metoda podbudowy
PublikacjaW pracy zajęto się wyznaczeniem nośności granicznej zbiorników stalowych o osi pionowej montowanych lub naprawianych z zastosowaniem hydraulicznego systemu podnoszenia konstrukcji. Podniesiony zbiornik jest szczególnie narażony na utratę stateczności, a obciążenie wiatrem utrudnia prowadzenie prac. Jakiekolwiek deformacje blach, szczególnie w pobliżu zamocowań podnośników mogą w znacznym stopniu obniżyć obciążenie krytyczne konstrukcji....
-
Biodegradability of simulant fluids and crude oil in aquatic environment
PublikacjaBiodegradowalność symulantów płynów była oceniana poprzez pomiar CO2 (EPA 560/6-82-003). Badaniu poddawane były emulsyjne i nieemulsyjne symulanty ropy oraz lekka ropa naftowa typu A z Północnej Ameryki. Uzyskane wyniki wskazują na łatwą biodegradowalność obu symulantów w porównaniu do badanej ropy naftowej.
-
Analysis of electricity generation variability in 2019 with special consideration of electrical energy generation from wind sources.
PublikacjaThis article presents issues related to the broadly understood development of wind energy. The state of the art of wind energy in the world has been discussed. This paper also shows issues related to factors affecting the development of renewable energy sources and their impact on the natural environment on the basis of available research. The focus is, however, on the critical analysis of phenomena in the data of the Transmission...
-
Influence of geometrical imperfections on stresses in cylindrical shells
PublikacjaResults of the numerical analysis of the shells of storage tanks of 50 000 m3 capacity with geometrical imperfections are presented in the paper. Results were verified by tensometric tests performed on the real tank. It was recognized that real geometrical imperfections cause increase of stresses in the tank construction by 30%.
-
Ground anchors diagnostic process based on elastic wave propagation method
PublikacjaThe paper is focused on analysis of elastic wave propagation in the context of diagnostics of ground anchors. Numerical simulations were performed to assess the possibility of evaluation of the anchorage quality. It was assumed that the quality and the load capacity of the anchor system directly depend on the length, on which mortar and steel cooperate.
-
Technical and Economic Analysis of an Intermediate Size Photovoltaic Power Plant. Case Study
PublikacjaThe article presents an analysis of the construction of a photovoltaic power plant with an installed capacity of about 30 kW. The principles of selecting the basic elements of the plant are shown. The impact of a high constant price on the profitability of the project is highlighted. The article also describes the existing mechanisms for subsidizing the investment.
-
Analysis of The Behavior of Foundations of Historical Buildings
PublikacjaThe article is devoted to the analysis of the behavior of the foundations of historic buildings. Some basic aspects of foundation engineering are discussed, with an emphasis placed on its development, applied techniques, and materials. Several different approaches and methods for the analysis of foundations of historical buildings are presented. A particular analysis has been focused on an example of a typical stone foundation...
-
Shear Cap Size Selection Method Based on Parametric Analysis of ACI-318 Code and Eurocode 2 Standard
PublikacjaThe scope of the paper is to propose a method for determining the size of shear caps in a slab–column-connections-reinforced concrete structure. Usually, shear heads are used to enhance slab–column connection, especially when the transverse reinforcement does not give the required punching shear load capacity. The dimensions of the shear head should provide the punching shear resistance of the connection inside and outside the...
-
Overheating of underground power cable line due to its partial exposition to solar radiation
PublikacjaCurrent-carrying capacity of underground power cable lines depends, among others, on thermal resistivity of the soil and cables layout: trefoil formation, flat formation with or without spacing. If conditions for heat transfer in the ground are favorable, the current-carrying capacity is relatively high. Therefore, it generates risk of the power cables overheating, if part of the cable line is located vertically in the air, to...
-
Uproszczone metody obliczania wyboczenia silosów z blachy falistej wzmocnionych słupami na podstawie analizy MES i wyników doświadczalnych
PublikacjaRozprawa doktorska dotyczy zagadnienia stateczności i nośności granicznej stalowych silosów z płaszczem z blachy falistej wzmocnionych pionowymi słupami. Przeprowadzono zaawansowane analizy numeryczne MES oraz badania doświadczalne dotyczące wyboczenia/stateczności analizowanych silosów. Analizy numeryczne zostały przeprowadzone w zakresie liniowej oraz nieliniowej analizy stateczności, z uwzględnieniem wstępnych imperfekcji geometrycznych...
-
Strategien der NSZZ Solidarność. Ein kurzer Abriss über bewährte Verfahrensweisen
PublikacjaDuring the recent years, the difficulties faced by trade unions to maintain their representation base and capacity to regulate employment relations have provoked numerous discussions. The issue of declining trade union membership, as well as density, has been repeatedly addressed by major trade unions including NSZZ “S”.
-
Design of radio communication systems for unmanned transport applications
PublikacjaIn the paper the principle of OFDMA-based radio communication systems design for unmanned transport applications is presented. The concept of system radio interface is analysed and its basic parameters proposal are considered. In the last part of the paper some air interface characteristics useful for optimization of throughput and system capacity are considered.
-
Comparison of Cadmium Cd2+ and Lead Pb2+ Binding by Fe2O3@SiO2‐EDTA Nanoparticles – Binding Stability and Kinetic Studies
PublikacjaThis study describes the synthesis and characterization of ethylenediaminetetraacetic acid (EDTA) functionalized magnetic nanoparticles of 20 nm in size – Fe3O4@SiO2‐EDTA – which were used as a novel magnetic adsorbent for Cd(II) and Pb(II) binding in aqueous medium. These nanoparticles were obtained in two‐stage synthesis: covering by tetraethyl orthosilicate and functionalization with EDTA derivatives. Nanoparticles were characterized...
-
Evolution of charge density wave order in continuous solid solutions Lu(Ni1-xCox)C2
PublikacjaPseudo-ternary solid solutions, Lu(Ni1-xCox)C2 (0 ≤ x ≤ 1), were studied by means of powder X-ray diffraction, differential thermal analysis as well as electrical resistivity and heat capacity measurements. The crystal structure of the Lu(Ni1-xCox)C2 series, as investigated by means of X-ray powder diffraction, is of structure type CeNiC2, space group Amm2, Pearson symbol oS8. The structural analysis reveals a non-monotonous evolution,...
-
N-doped graphene quantum dot-decorated MOF-derived yolk-shell ZnO/NiO hybrids to boost lithium and sodium ion battery performance
PublikacjaSurface engineering at the nanoscale to obtain robust interface between metal oxides and quantum dots is essential for improving the performance and stability of battery materials. Herein, we designed and prepared novel N-doped graphene quantum dot-modified ZnO/NiO anode materials with a well-defined yolk-shell structure for lithium and sodium-ion batteries. NG QDs were assembled on the ZnO/NiO microspheres using three different...
-
CaO-based high temperature CO2 sorbents – Literature review
PublikacjaThe use of CaO-based adsorbents has a high potential to capture CO2 from various systems due to its high reactivity with CO2, high capacity, and low cost of naturally derived CaO. The application of CaO-based sorbents to remove carbon dioxide is based on a reversible reaction between CaO and CO2. However, multiple carbonation/calcination cycles lead to a rapid reduction in the sorption capacity of natural CaO, and therefore efforts...
-
A facile strategy for reclaiming discarded graphite and harnessing the rate capabilities of graphite anodes
PublikacjaGraphite negative electrodes are unbeaten hitherto in lithium-ion batteries (LiBs) due to their unique chemical and physical properties. Thus, the increasing scarcity of graphite resources makes smart recycling or repurposing of discarded graphite particularly imperative. However, the current recycling techniques still need to be improved upon with urgency. Herein a facile and efficient hydrometallurgical process is reported to...
-
Structure redetermination, transport and thermal properties of the YNi3Al9 compound
PublikacjaSingle crystals of completely ordered variant of the YNi3Al9 compound were grown by self-flux method with excess of aluminum. The crystal structure of the title compound was redetermined from single crystal X-ray diffraction data. The structure adopts ErNi3Al9 type, space group R32, parameters of the unit cell a = 7.2838(2) Å, c = 27.4004(8) Å. The growth of relatively large single crystals of the YNi3Al9 compound, having completely...
-
Moment resistance of I-section end-plate roof girder splices; a case study
PublikacjaThis article deals with the problem of determining the resistance of end-plate connections. A nonlinear FEM model of the joint was constructed in order to predict its carrying capacity. A standard code procedure was done as well. The analyses have been done to assess atypical end-plate joints designed and constructed as a part of roof structures.
-
Modelling the loss of time caused by traffic incidents on motorways
PublikacjaFor each road incident important factors like location, capacity reduction, traffic management, duration of road incidents and amount of traffic should be defined. All performer operations and effects of incidents affect the capacity of the road, average speed, time loss, vehicle queues and traffic jams. In the article road incidents were divided into planned and unexpected. Statistical analysis prepared using the database of traffic...
-
Superconductivity in the intermetallic compound Zr5Al4
PublikacjaPolycrystalline Zr5Al4 was synthesized using the arc-melting method. Powder X-ray diffraction confirms the previously reported crystal structure of the Ti5Ga4-type P63/mcm with lattice parameters: a = 8.4312(6) A , and c = 5.7752(8) A . Electrical resistivity and low-temperature magnetic susceptibility measurements indicate that Zr5Al4 exhibits superconducting behavior below 2 K. The normalized heat capacity jump at Tc= 1.82 K...
-
Experimental Testing of Innovative Cold-Formed "GEB" Section / Badania Eksperymentalne Innowacyjnego Kształtownika Giętego Na Zimno Typu „Geb“
PublikacjaOne of the major advantages of light gauge steel structures made of cold-formed steel sections is their low weight, so manufacturers are increasingly using the possibilities of those sections for the production of typical single-storey steel structures systems. Well known profiles, such as Z, C and the so called hat sections that have been studied and described in the literature, are used mainly as purlins or truss components....
-
Elementary analysis and energetic potential of the sludge from the Gdynia Dębogórze and Lębork wastewater treatment plants
PublikacjaThe paper aims to show the results of the elementary analysis of the sewage sludges from wastewater treatment plants in Gdynia Dębogórze and Lębork as well as measurements of the heat of combustion and the calculated calorific values according to regulation PN-93/Z-15008, taking into account water content and the composition of sewage sludge at different utilisation stages. The results presented in this paper are based on the analysis...
-
Innovative cold-formed GEB section under compression
PublikacjaCold-formed steel sections extensively affect the modern steel construction industry. Not only are they used as secondary elements like purlins or sheeting, but also they can serve as primary load-bearing members in fabricated steel panels and trusses. A new cross-section called shortly a GEB may serve as that member. However, its existence of the metal building structures industry depends on the exact, optimal dimensional parameters...
-
Removal of nonsteroidal anti-inflammatory drugs and analgesics from wastewater by adsorption on cross-linked β-cyclodextrin
PublikacjaWe present a method using the material in the form of cross-linked β-cyclodextrin (CD) showing high efficiency in the simultaneous removal of hazardous pollutants from sewage, such as diclofenac (DIC), ibuprofen (IBU), ketoprofen (KETO), naproxen (NAPR), salicylic acid (SALI) and tramadol (TRAM). The material is stable and particularly easy to regenerate. The sorbent probably remembers the shape of the contaminants, which increases...
-
Single crystal growth and physical properties of MCo2Al9 (M= Sr, Ba)
PublikacjaSingle crystals of SrCo2Al and BaCo2Al9 were grown using a self-flux method. A LeBail analysis of the powder X-ray diffraction patterns show that both compounds crystallize in a hexagonal (P6/mmm) crystal structure with lattice parameters: a = 7.8995(1) Å, c = 3.9159(1) Å for SrCo2Al9, and a = 7.9162(2) Å, c = 3.9702(1) Å for BaCo2Al9 aluminide. The low temperature analysis of the heat capacity measurements give a Sommerfeld...