Filtry
wszystkich: 919
wybranych: 740
Wyniki wyszukiwania dla: nanohydroxyapatite coatings
-
Chapter 13 : The influence of dispersion phase on composite coating properties after cold working
PublikacjaW pracy określono wpływ fazy dyspersyjnej Al2O3 na wybrane potencjalne właściwości powłok kompozytowych o osnowie niklowej. Powłoki Ni-Al-Al2O3 zostały nałożone na próbki stalowe przy użyciu technologii poddźwiękowego płomieniowego natryskiwania cieplnego. Następnie poddane zostały obróbce plastycznej na zimno i na gorąco poprzez walcowanie, a także prasowania na zimno na prasie hydraulicznej. Obróbka plastyczna jest metodą alternatywną...
-
The Effect of Texturing of the Surface of Concrete Substrate on the Pull-Off Strength of Epoxy Resin Coating
Publikacja -
Evaluation of organic coating systems for corrosion protection of industrial equipment using impedance spectroscopy
PublikacjaThe high economic impact of corrosion can be reduced by enhanced corrosion management and prevention based on appropriate means. This applies in particular to the protection of structures with organic protective coatings. Steel is subject to corrosion that reduces its service life and leads to destruction in most severe cases. The application of paints to metallic objects for corrosion control has been known for a long time and...
-
Damage tests of the single shell ship fuel tank with additional elastic protective coating
PublikacjaWejście na mieliznę lub kolizja średniej wielkości np. kontenerowca może doprowadzić do zanieczyszczenia środowiska Morza Bałtyckiego paliwem uwolnionym z rozszczelnionych, jednoposzyciowych zbiorników dennych, a ilość tego paliwa może być znaczna. W związku z tym podjęto prace badawcze zmierzające do opracowania sposobu obniżenia ryzyka rozlewu paliwa w wypadku kolizji poprzez wprowadzenie drugiej bariery ochronnej. Idea pomysłu...
-
Multispectral impedance quality testing of coil-coating system using principal component analysis
PublikacjaThe task of quality checking of the coil-coated system was undertaken using impedance spectroscopy. In order to properly characterize the system the new impedance spectrum was calculated as an averaged result of 12 experimental spectra obtained from 12 different places of the sample at the same time of immersion in 3% of NaCl. The experimental spectra were recorded for a 24-h period at 1 h intervals between starting points of each...
-
Functional fluorine-doped tin oxide coating for opto-electrochemical label-free biosensors
PublikacjaSensors operating in multiple domains, such as optical and electrochemical, offer properties making biosensing more effective than those working in a single domain. To combine such domains in one sensing device, materials offering a certain set of properties are required. Fluorine-doped tin oxide (FTO) thin film is discussed in this work as functional optically for guiding lossy modes and simultaneously electrochemically, i.e....
-
Biopolymers based paper coating with promoted grease resistivity, bio-degradable and mechanical properties
Publikacja -
Anticorrosive and antimicrobial efficiency of photopolymerizable phosphorus (meth)acrylate oligomers-based coating materials
Publikacja -
Optical-Fiber Microsphere-Based Temperature Sensors with ZnO ALD Coating—Comparative Study
PublikacjaThis study presents the microsphere-based fiber-optic sensor with the ZnO Atomic Layer Deposition coating thickness of 100 nm and 200 nm for temperature measurements. Metrological properties of the sensor were investigated over the temperature range from 100 °C to 300 °C, with a 10 °C step. The interferometric signal was used to monitor the integrity of the microsphere and its attachment to the connecting fiber. For the sensor...
-
Influence of porous coating on heat transfer during flow boiling of R22, R134a and R407C
PublikacjaPrzedstawiono wpływ pwłoki porowatej w pozionej rurce podczas wrzenia w przepływie i spadku ciśnienia czynników chłodniczych R22, R134a i R407C.
-
Using impedance spectroscopy to characterize and monitor protection aspects of organic coating systems on metal
PublikacjaOrganiczne powłoki ochronne stosowane są powszechnie do ochrony konstrukcji metalowych przed korozją i zużyciem mechanicznym. W pracy zaproponowano nowy typ sensora impedancyjnego, który może być zastosowany do ciągłej oceny właściwości barierowych i adhezyjnych systemów powłokowych w warunkach terenowych w sposób nieniszczący, bez konieczności stosowania naczyń z elektrolitem. Przedstawiono koncepcję czujnika oraz przykładowe...
-
Silica-Based Ionogels: Nanoconfined Ionic Liquid-Rich Fibers for Headspace Solid-Phase Microextraction Coupled with Gas Chromatography–Barrier Discharge Ionization Detection
PublikacjaIn this work, hybrid silica-based materials with immobilized ionic liquids (ILs) were prepared by sol–gel technology and evaluated as solid-phase microextraction (SPME) fiber coatings. High loadings of the IL 1-methyl-3-butylimidazolium bis(trifluoromethylsulfonyl)imide ([C4MIM][TFSI]) were confined within the hybrid network. Coatings composition and morphology were evaluated using scanning electron microscopy and energy dispersive...
-
Method of managing drill cuttings from shale gas formations
PublikacjaProposed management method of drill cuttings involves recycling for the expanded clay production. A theoretical presentation of the possibility, choosing planning path based on similarity between the materials used in the manufacture of expanded clay and oily cuttings. Application for the main stages of manufacture of expanded clay production of drill cuttings from shale gas extraction. Introduced into circulation solid waste partly...
-
On bounded load routings for modeling k-regular connection topologies
PublikacjaW pracy analizowane są problemy modelowania k-regularnych topologii sieci komputerowych z punktu widzenia routingu typu point-to-point. Zaprezentowane są algorytmy oraz przeprowadzona jest analiza złożoności obliczeniowej.
-
Effect of the Unit Pressure on the Selection Parameters of Intermetallic Coastings NiAl and Ni3Al after Platic Working
PublikacjaW artykule omówiono wpływ zgniotu na wybrane parametry warstwy międzymetalicznej NiAl i Ni3Al napawanej na stali C45 podanej obróbce plastycznej poprzez prasowanie na zimno.
-
Results of acoustic emission tests of corrosion protection degree of ship steel tanks covered by means of protective coatings (Phase I)
PublikacjaThis paper presents methods and results of the 1st series of tests of acoustic emission (AE) signals, aimed at assessing degree of corrosion protection of a tank made of hull structural steel, protected by means of a protective coating combined from polyurethane layer and concrete filler. The tests were carried outin compliance with a method specially elaborated for application to the work in question. In the method were used requirements...
-
Fuzzy reasoning approach to properties' determination of calcium phosphate coatings processed using ion beam assisted deposition on heated substrates
PublikacjaPraca przedstawia rozmyty system wnioskowania dla zamodelowania związków pomiędzy temperaturą podłoża oraz stosunkiem molowym Ca/P w gradientowej powłoce hydroxyapatytowej na podłożu tytanowym. Przeprowadzono symulację działania sterownika rozmytego na pomocą oprogramowania Matlab.
-
Solid State Conductivity of Optimized Polypyrrole Coatings on Iron Obtained from Aqueous Sodium Salicylate Solution Determined by Impedance Spectroscopy
PublikacjaIn this work the optimization procedure for corrosion resistance, surface analysis and electrical properties of PPy-Fe electrodes have been examined. Polypyrrole (PPy) film was electrochemically synthesized in a one step process from an aqueous solution of sodium salicylate and pyrrole with certain concentrations, different parameters and type of polymerization...
-
Artificial neural network model of hardness, porosity and cavitation erosion wear of APS deposited Al2O3 -13 wt% TiO2 coatings
Publikacja -
Osteoblast and bacterial cell response on RGD peptide‐functionalized chitosan coatings electrophoretically deposited from different suspensions on Ti13Nb13Zr alloy
PublikacjaMetallic materials for long-term load-bearing implants still do not provide high antimicrobial activity while maintaining strong compatibility with bone cells. This study aimed to modify the surface of Ti13Nb13Zr alloy by electrophoretic deposition of a chitosan coating with a covalently attached Arg-Gly-Asp (RGD) peptide. The suspensions for coating deposition were prepared in two different ways either using hydroxyacetic acid...
-
Evaluation of adhesion strength, corrosion, and biological properties of the MWCNT/TiO2 coating intended for medical applications
PublikacjaMulti-wall carbon nanotube (MWCNT) coatings are gaining increasing interest because of their special properties used in many science fields. The titania coatings are known for their improvement of osteoblast adhesion, thus changing the surface architecture. Bi-layer coatings comprising 0.25 wt% of the MWCNTs and 0.30 wt% of titania (anatase structure) were synthesized in a two-stage procedure using the electrophoretic deposition...
-
Solid Phase Micro-Extraction, a Versatile and Handy Tool in Environmental Trace Organic Analysis, Gets a New Class of Coatings, Polymeric Ionic Liquids
PublikacjaSolid phase microextraction (SPME) fundamentals, characteristics and application are described. The special stress is put on characteristics of sorbents used as SPME fiber coatings. Description of commercially available fibers and the present-day trends in development of new sorbents for SPME are given. Discussion is focused on possibility of application of ionic liquids (IL) and polymeric ionic liquids (PIL) as SPME fiber coatings....
-
Deterioration and Protection of Concrete Elements Embedded in Contaminated Soil: A Review
PublikacjaCoating materials are considered one of the most antique materials of human civilization; they have been used for decoration and the protection of surfaces for millennia. Concrete structures—due to their permanent exposure to different types of environments and contaminants—require the use of coatings that contribute to its preservation by reducing the corrosion of its components (steel and aggregates). This article intends to...
-
High temperature oxidation behavior of SUS430 SOFC interconnects with Mn-Co spinel coating in air
PublikacjaIn this study, SUS430 alloy is evaluated for its high temperature corrosion properties as a possible material for interconnects of solid oxide fuel cells (SOFCs). Samples are coated with Mn-Co by commercial physical vapor deposition (PVD) process and oxidized in air for 1250 h at 800 °C. A dense cubic Mn-Co-Fe spinel layer is formed on the surface, showing great effect on corrosion reduction compared with the samples without coating....
-
Preparation and Characterization of Microsphere ZnO ALD Coating Dedicated for the Fiber-Optic Refractive Index Sensor
PublikacjaWe report the fabrication of a novel fiber-optic sensor device, based on the use of a microsphere conformally coated with a thin layer of zinc oxide (ZnO) by atomic layer deposition (ALD), and its use as a refractive index sensor. The microsphere was prepared on the tip of a single-mode optical fiber, on which a conformal ZnO thin film of 200 nm was deposited using an ALD process based on diethyl zinc (DEZ) and water at 100 °C....
-
Aluminide Thermal Barrier Coating for High Temperature Performance of MAR 247 Nickel Based Superalloy
Publikacja -
Improving carboxymethyl cellulose edible coating using ZnO nanoparticles from irradiated Alternaria tenuissima
Publikacja -
Zirconia-based mixed potential sensor with Pt electrode prepared by spin-coating of polymeric precursor
PublikacjaMany types of yttria-stabilized zirconia (YSZ) based gas sensors have been explored extensively in recent years. Great attention have been directed to mixed-potential-type gas sensors. It is due to growing concerns with environmental issues. Not without a significance is the fact of very attractive performance of this type of sensor allowing to detect low concentration of pollutant gases. In this paper two types of YSZ based mixed-potential...
-
Suspension and process parameters selection for electrophoretic deposition of Mn–Co spinel coating on steel interconnects
PublikacjaMetallic interconnect coatings, consisting of MnCo2O4 spinel, were effectively applied to Crofer 22 APU using the electrophoretic deposition (EPD) method in both H2O: ethanol and pure ethanol solvents. The primary goal of this method was to prevent chromium migration, minimize evaporation, and control the oxidation rate. The study aimed to assess the quality, adhesion, and thickness of the Mn–Co coating, with the objective of...
-
Electrochemical behaviour of Cr coating in acidic sulphate solution studied by cyclic polarization and impedance spectroscopy
PublikacjaOdporność korozyjną powłok chromowych w 0.01 M H2SO4 zbadano metodami woltamperometrii cyklicznej i spektroskopii impedancyjnej. Stwierdzono, że właściwości ochronne powłoki chromowej w kontakcie z powietrzem wzrastają dzięki tworzeniu się warstwy tlenkowej zapełniającej defekty w powłoce. W trakcie polaryzacji anodowej następuje częściowe roztwarzanie tej warstwy i penetracja agresywnego środowiska do podłoża (stali), co powoduje...
-
Underwater Electrochemical Offshore Tests of a Paint Coating Applied in Water on the Legs of an Oil Production Platform
PublikacjaThis paper presents the methodology developed for underwater measurements using electrochemical impedance spectroscopy (EIS) technique, aimed at determining the resistance of an epoxy coating applied in seawater to the legs of an oil production platform. Performing such underwater tests in an offshore environment was technically challenging. The results of measurements obtained on the platform were confronted with comparative results...
-
Buckling Analysis of a Micro Composite Plate with Nano Coating Based on the Modified Couple Stress Theory
PublikacjaThe present study investigates the buckling of a thick sandwich plate under the biaxial non-uniform compression using the modified couple stress theory with various boundary conditions. For this purpose, the top and bottom faces are orthotropic graphene sheets and for the central core the isotropic soft materials are investigated. The simplified first order shear deformation theory (S-FSDT) is employed and the governing differential...
-
Elastic protection coasting for ship tanks to increase environment protection level
PublikacjaW opracowaniu przedstawiono ideę nowego rozwiązania dla podniesienia bezpieczeństwa zbiorników paliwowych statków, polegającą na wprowadzeniu do zbiornika drugiej - elastycznej bariery ochronnej opartej na warstwie wypełniacza.
-
The concept of weighted mean friction angle in bearning capacity of footings of sands
PublikacjaZagadnienie średniej ważonej kąta tarcia wewnętrznego w nośności fundamentów posadowionych w gruntach niespoistych.
-
Optimized Stress and Geometry Control of Spherical structures under Lateral Loadings
PublikacjaIn this paper, a numerical model of a double-layer spherical structure has been examined under lateral loadings. When the structure has been distorted due to loadings, the dislocated joints have been moved to their original positions utilizing the adjustment techniques based on the force method. Meanwhile, the members’ internal forces were kept in the desired domain. Optimization techniques were also implemented in order to minimalize...
-
Lasing thresholds of plasmon and grating modes of coated silver nanowire gratings
Publikacja -
Size effects in problems of footings on sand within micro-polar hypoplasticity.
PublikacjaW artykule przedstawiono obliczenia efektów skali na nośność fundamentu na piasku. Obliczenia wykonano przy pomocy mikropolarnego prawa hipoplastycznego. W obliczeniach wykorzystano stochastyczne rozkłady początkowego wskaźnika porowatości według rozkładu Gaussa oraz różne wymiary fundamentu.
-
Problemy z powłokami antykorozyjnymi na elementach wyposażenia obiektów mostowych
PublikacjaOpisano problem wadliwości zabezpieczenia antykorozyjnego w zakresie malarskich powłok ochronno-dekoracyjnych wykonywanych na stalowych elementach barier zabezpieczonych uprzednio poprzez ocynkowanie metodą zanurzeniową na gorąco. Wykorzystując przykłady pochodzące z różnych obiektów przedstawiono powtarzający się problem delaminacji powłok malarskich, niezależny od rodzaju zastosowanych wyrobów lakierniczych oraz znacznego rozwoju...
-
Problemy z powłokami antykorozyjnymi na elementach wyposażenia obiektów mostowych
PublikacjaPrzedstawiono problem wadliwości zabezpieczenia antykorozyjnego w zakresie malarskich powłok ochronno - dekoracyjnych wykonywanych na stalowych elementach barier zabezpieczonych uprzednio poprzez ocynkowanie metodą zanurzeniową. Wykorzystując przykłady pochodzące z różnych obiektów przedstawiono powtarzający się problem delaminacji powłok malarskich, niezależny od rodzaju zastosowanych wyrobów lakierniczych oraz znacznego rozwoju...
-
Electrophoretic co-deposition of Fe2O3 and Mn1,5Co1,5O4: Processing and oxidation performance of Fe-doped Mn-Co coatings for solid oxide cell interconnects
PublikacjaThe “in-situ” Fe-doping of the manganese cobalt spinel was achieved by electrophoretic co-deposition of Mn1,5Co1,5O4 and Fe2O3 powders followed by a two-step reactive sintering treatment. The effects on the coating properties of two different Fe-doping levels (5 and 10 wt.% respectively) and two different temperatures of the reducing treatment (900 and 1000 °C) are discussed. Samples with Fe-doped coatings demonstrated a lower...
-
Properties of Spark Plasma Sintered Compacts and Magnetron Sputtered Coatings Made from Cr, Mo, Re and Zr Alloyed Tungsten Diboride
Publikacja -
Powłoki fluoropolimerowe oraz przeciwzatarciowe w łożyskach foliowych smarowanych wodą = Fluoropolymer and anti-friction coatings for water-lubricated foil bearings
PublikacjaW artykule przedstawiono krótką charakterystykę oraz wyniki badań tribologicznych wybranych powłok fluoropolimerowych oraz przeciwzatarciowych. Badania zużycia powłok przeprowadzono pod kątem zastosowania w oryginalnym łożysku foliowym smarowanym wodą. Na podstawie analizy wyników wyłoniono trzy powłoki do potencjalnego zastosowania w łożyskach foliowych smarowanych wodą.
-
Ni/cerium Molybdenum Oxide Hydrate Microflakes Composite Coatings Electrodeposited from Choline Chloride: Ethylene Glycol Deep Eutectic Solvent
PublikacjaCerium molybdenum oxide hydrate microflakes are codeposited with nickel from a deep eutectic solvent-based bath. During seven days of exposure in 0.05 M NaCl solution, the corrosion resistance of composite coating (Ni/CeMoOxide) is slightly reduced, due to the existence of some microcracks caused by large microflakes. Multielemental analysis of the solution, in which coatings are exposed and the qualitative changes in the surface...
-
Iron doped manganese cobaltite spinel coatings produced by electrophoretic co-deposition on interconnects for solid oxide cells: Microstructural and electrical characterization
PublikacjaWe report a systematic microstructural and electrical characterization of iron doped Mn–Co spinel coatings processed by electrophoretic co-deposition of Mn1.5Co1.5O4 and Fe2O3 powders on Crofer 22 APU and AISI 441 steel substrates. Iron addition to Mn–Co spinel coating leads to a reduction of the area specific resistance on both substrates, after 3200 h at 750 °C. The Fe doped Mn–Co coating both leads to a thinner oxide scale and...
-
Biological properties of chitosan/Eudragit E 100 and chitosan/poly(4-vinylpyridine) coatings electrophoretically deposited on AgNPs-decorated titanium substrate
PublikacjaThe objective of the study was the determination of the response, in contact with human osteoblast-like MG-63 cells, of electrophoretically deposited coatings composed of chitosan (CS), Eudragit E 100 (EE100), or poly(4- vinylpyridine) (P4VP) on a silver nanoparticle (AgNPs)-decorated titanium substrate. Before deposition, the substrate was coated with silver by electro-reduction of silver nitrate. The coatings deposition was carried...
-
Influence of dispersed phase content on the mechanical properties of electroless nanocomposite Ni-P/Si3N4 and hybrid Ni-P/Si3N4/graphite layers deposited on the AW-7075 alloy.
PublikacjaThe article presents the results of mechanical testing of Ni-P/Si3N4 nanocomposite and hybrid Ni-P/Si3N4/graphite coatings deposited on AW-7075 aluminum alloy using the chemical reduction method. In terms of mechanical testing, microhardness was measured, and surface roughness and adhesion of the coatings to the aluminum substrate were determined using the “scratch test” method. The surface morphology of the deposited layers was...
-
Effective yttrium based coating for steel interconnects of solid oxide cells: Corrosion evaluation in steam-hydrogen atmosphere
PublikacjaThis work describes manufacture, analysis and test of a new well conducting corrosion-protection coating that can be applied on steel types with high chromium content. Electrolytic deposition of yttrium salts is used to form thin (<100 nm) coatings on both flat steel sheets (material: Crofer 22 APU) and its properties are proven on woven wire-meshes (materials from two different sources: SUS316 and SUS316L). The oxide scale on...
-
The development of an indirect ELISA for the detection of goose parvovirus antibodies using specific VP3 subunits as the coating antigen
PublikacjaIn Poland, the leader in goose production in Europe, goose parovirus infection, or Derzsy’s disease (DD), must be reported to the veterinary administration due to the serious economic and epizootic threat to waterfowl production. Prophylactic treatment for DD includes attenuated live or inactivated vaccines. Moreover, the control of DD includes the monitoring of maternal derived antibody (MDA) levels in the offspring and antibody...
-
A new type of (TiZrNbTaHf)N/MoN nanocomposite coating: Microstructure and properties depending on energy of incident ions
PublikacjaA novel (TiZrNbTaHf)N/MoN nanocomposite coatings, which consist of the nitride of the high-entropy alloy and the binary nitride, were synthesized by vacuum-arc deposition at various substrate biases. The elemental composition, chemical bonding state, phase structure, microstructure and mechanical properties of the coatings were studied by high-resolution experimental methods: SIMS, GDMS, XPS, XRD, HR-TEM and nano-indentation. It...
-
Nanocomposites of Graphene Oxide—Silver Nanoparticles for Enhanced Antibacterial Activity: Mechanism of Action and Medical Textiles Coating
Publikacja