Filtry
wszystkich: 632
wybranych: 509
Wyniki wyszukiwania dla: CIRCULAR WAVEGUIDE
-
Shielded HMSIW-Based Self-Triplexing Antenna With High Isolation for WiFi/WLAN/ISM Band
PublikacjaThis article presents a novel design of a miniaturized self-triplexing antenna (STA) based on the shielded half-mode substrate integrated waveguide (S-HMSIW) for WiFi/WLAN/ISM-band applications. The S-HMSIW is constructed by assembling one row of vias and an open slot at the open-ended side of the conventional HMSIW. This configuration increases the quality factor and minimizes unwanted radiation loss, which allows for achieving...
-
Design and Characterization of a Planar Structure Wideband Millimeter-Wave Antenna with Wide Beamwidth for Wearable off-body Communication Applications
PublikacjaThis letter presents the design of a planar single-layer wideband antenna featuring wide beamwidth has well as high and stable in-band gain. The proposed antenna is a planar monopole fed by a bottom-grounded coplanar waveguide to realize wide beamwidth in both the xz- and yz-planes. Simultaneous optimization of all adjustable antenna parameters, carried out at the full-wave electromagnetic simulation level. The constructive interference...
-
Wpływ zbrojenia polimerowymi włóknami rozproszonymi na wybrane właściwości mieszanek mineralno-asfaltowych
PublikacjaW artykule przedstawiono wybrane wyniki badań mieszanek mineralno-asfaltowych zbrojonych polimerowymi włóknami rozproszonymi. Ocenie poddano mieszankę włókien zbrojących aramidowo-poliolifenowych pod kątem wpływu ich zastosowania na właściwości niskotemperaturowe i odporności na deformacje trwałe mieszanek mineralno-asfaltowych. Właściwości niskotemperaturowe oceniano na podstawie testu zginania próbek belkowych oraz na podstawie...
-
The application of nonlinear curvature sections in the turnout diverging track
PublikacjaThe paper presents the analytical method of modelling the diverging track of railway turnout with nonlinear curvature sections. These sections were used for smoothing the graph of curvature in the extreme areas of turnout. The problem of the curvature distribution was identified with the use of differential equations. The resulting solutions are of universal nature for example the ability of assuming any values of curvature at...
-
Imaging of Increasing Damage in Steel Plates Using Lamb Waves and Ultrasound Computed Tomography
PublikacjaThis paper concerns inspection of steel plates, with particular emphasis on the assessment of in-creasing damage. Non-destructive tests were performed on four plates, one of which was un-damaged, while the remaining three had a defects in the form of circular holes with a diameter of 2, 5, and 10 cm. Guided Lamb waves were used in the research, and the image reconstruction was performed using ultrasound computed tomography. The...
-
A material model of asphalt mixtures based on Monte Carlo simulations
PublikacjaThe paper aims to numerically reflect mineral-asphalt mixture structure by a standard FEM software. Laboratory test results are presented due to bending tests of circular notched elements. The result scatter is relatively high. An attempt was made to form a random aggregate distribution in order to obtain various results corresponding to laboratory tests. The material structure calibration, its homogenization and finite element...
-
Zastosowanie odcinków nieliniowej krzywizny w torze zwrotnym rozjazdu kolejowego
PublikacjaW pracy została przedstawiona analityczna metoda kształtowania toru zwrotnego rozjazdu kolejowego posiadającego na swojej długości odcinki nieliniowej krzywizny. Odcinki te służą łagodzeniu wykresu krzywizny w skrajnych strefach rozjazdu W omawianej metodzie dokonano identyfikacji problemu rozkładu krzywizny za pomocą równań różniczkowych. Uzyskane rozwiązania mają charakter uniwersalny; m. in. pozwalają na przyjmowanie dowolnych...
-
Integrated controller for ultra high frequency technique laboratory
PublikacjaDepartment of Microwave and Antenna Engineering decided to modernize the laboratory of Ultra High Frequency Techniques. The main change was to replace measurement of the field distribution inside rectangular waveguides by analysing the fields around striplines. This involved the need to overcome several technical and conceptual problems. Precise positioning of the probe and reading the field distribution near the stripline is important...
-
On modelling and non-linear elasto-plastic analysis of thin shells with deformable junctions
PublikacjaThe undeformed base surface of the irregular thin shell is modelled by the union of a finite number of regular smooth surface elements joined together along spatial curvilinear surface edges. The equilibrium conditions are formulated by postulating an appropriate form of the principle of virtual work, where also deformability of shell junctions is taken into account. The PVW is then discretised by C1 finite elements and the incremental-iterative...
-
Preliminary studies on the effect of feed speed on the colour change of wood
PublikacjaThis paper presents the results of preliminary analyses of the effect of cutting parameters on changes in the colour of wood. Beech wood cut with use circular saw was analysed. The cutting parameter tested was the feed speed, represented by the feed per tooth. Sawing processes with different feed per tooth ranging from 0.0008 mm to 0.09 mm were analysed. It was observed that over the entire range of feed rate per tooth analysed,...
-
Nowe kierunki usuwania azotu w oczyszczalniach ścieków
PublikacjaW 2015 roku Komisja Europejska przyjęła nową strategię gospodarki o obiegu zamkniętym (ang. Circular Economy), której celem jest efektywne wykorzystanie zasobów, a także zwiększenie roli gospodarki odpadami. Działania prowadzone w ostatnich latach w sektorze oczyszczania ścieków były ukierunkowane na rozwój efektywnej, niskoemisyjnej gospodarki zasobami, sprzyjającej wzrostowi bezpieczeństwa energetycznego i poprawie stanu jakości...
-
Projektowanie układów geometrycznych toru z zastosowaniem optymalizacji wielokryterialnej
PublikacjaW pracy przedstawiono metodę projektowania odcinków trasy kolejowej położonych w łuku, dostosowaną do techniki mobilnych pomiarów satelitarnych. Rozwiązanie problemu projektowego wykorzystuje zapis matematyczny i polega na wyznaczeniu uniwersalnych równań opisujących całość układu geometrycznego. Odbywa się to sekwencyjnie, obejmując kolejne fragmenty tegoż układu. Procedura projektowania ma charakter uniwersalny, gdyż w ogólnym...
-
Projektowanie łuków koszowych dostosowane do pomiarów satelitarnych
PublikacjaW pracy przedstawiono nową metodę projektowania rejonu zmiany kierunku trasy kolejowej, dostosowaną do techniki ciagłych pomiarów satelitarnych. Metoda ta może się okazać szczególnie przydatna podczas projektowania regulacji osi istniejącego toru, kiedy określenie obu kierunków głównych trasy okazuje się niemożliwe. Jedynym rozwiązaniem staje się wówczas wprowadzenie do układu geometrycznego dwóch łuków kołowych o różnym promieniu,...
-
Techniki zwiększania efektywności metody elementów skończonych poprzez redukcję dziedziny obliczeniowej z wykorzystaniem własności geometrii struktur
PublikacjaWspółczesna elektronika ze względu na swój szybki rozwój wymaga od nas efektywnego modelowania zjawisk polowych. Celem rozprawy jest zwiększanie efektywności metody elementów skończonych poprzez redukcję dziedziny obliczeniowej z wykorzystaniem własności geometrii struktur oraz jej hybrydyzację z użyciem technik analitycznych. Rozprawa zawiera przegląd stanu wiedzy na temat dostępnych obecnie technik modelowania jak również opis...
-
Hydrogen production from ethanol In nitrogen microwave plasma At atmospheric pressure
PublikacjaHydrogen seems to be one of the most promising alternative energy sources. It is a renewable fuel as it could be produced from e.g. waste or bio-ethanol. Furthermore hydrogen is compatible with fuel cells and is environmentally clean. In contrast to conventional methods of hydrogen production such as water electrolysis or coal gasification we propose a method based on atmospheric pressure microwave plasma. In this paper we present...
-
Optimum shape of turnout diverging track with segments of variable curvature
PublikacjaIn the paper an attempt has been made to focus on shaping the variable curvature in the diverging track of the railway turnout. Basing on some earlier studies, solutions provided with a circular arc in the mid-zone, and in the extreme regions with segments of non-linear curvature of equal length and zero curvature at the start and end of the turnout, have been assumed as models. The most advantageous type of curvature has been...
-
The effect of a belt position in the spindle driving system on critical rotational speeds
PublikacjaThe aim of this paper was to examine how the belt pulley position affects critical rotational speeds of the modernized spindle of the sliding table saw Fx3. Methodology of determination of critical rotational speeds of the spindle in a function of the spindle design features and its driving system is presented. Spindles in these kind of machine tools are mainly driven with V-belts, and the pulleys on the spindles might be positioned:...
-
Design of compound curves adapted to the satellite measurements
PublikacjaThe paper deals with a novelty related to the design of a region for an alternative railway track direction adequate for mobile satellite measurements. The new approach may become particularly useful in the design of the existing track axis control when the determination of both the main track directions becomes impossible. The only solution in that case is to apply to the geometrical system two circular arcs of a different radius,...
-
The methodology of design of satellite working mechanism of positive displacement machine
PublikacjaIn this paper is described a methodology of design of satellite mechanism consisting of two noncircular gears (externally toothed rotor and internally toothed curvature) and circular gears (satellites). In the presented methodology is assumed that the rotor pitch line is known, and the curvature pitch line is necessary to designate. The presented methodology applies to mechanisms for which the number of the curvature humps is at...
-
Numerical simulation of natural convection of Glycol-Al2O3 nanofluids from a horizontal cylinder
PublikacjaThis paper deals with natural convection around a circular cylinder with constant heat flux in a cavity using computational fluid dynamics. As fluids ethylene glycol and a mixture of ethylene glycol with Al2O3 nanoparticles (mass concentrations of nanoparticles: 0.1% and 1%) are chosen. Rayleigh number ranges from 3104 to 3105. The nanofluids are modeled with single-phase approach. For the investigated range of nanoparticle concentration, the...
-
Edge-Guided Mode Performance and Applications in Nonreciprocal Millimeter-Wave Gyroelectric Components
PublikacjaThe analogies between the behavior of gyromagnetic and gyroelectric nonreciprocal structures, the use of the simple transfer matrix approach, and the edge-guided (EG) wave property, supported in a parallel plate model for integrated magnetized semiconductor waveguide, are investigated in those frequency regions, where the effective permittivity is negative or positive. As with their ferrite counterparts, the leakage of the EG waves...
-
UWB Microstrip Antennas on a Cylindrical Surfaces
PublikacjaConformal antennas are becoming popular due to their many advantages and possibilities of applications they offer. The advantages of using antennas with a curved surface arise not only from the possibility of integrating them with the object on which they are mounted on but also from the increase, relatively to planar antennas, of their visible angular range. The circular antenna arrays, or arrays of radiators located on the surface...
-
Analysis of turnouts with non-linear curvature of diverging track for different train running speeds
PublikacjaThe paper deals with the issue of shaping a variable curvature in the diverging track of the railway turnout. Solution without a circular arc in the central zone, comprising two zones of non-linear curvature, of the same length, having zero curvature values at the end points, was adopted as a model, on the basis of the previously conducted dynamic tests. Optimum type of curvature was selected from the point of view of the kinematic...
-
Ultrasonic Tomography of Brick Columns Based on FEM Calculations
PublikacjaUltrasonic tomography is one of the most developed method of non-destructive testing. Despite being used mainly in medicine, it is becoming more and more popular as a method for monitoring of structural elements. It allows to examine the internal structure and technical condition of the tested element. This paper investigates the influence of crosssectional geometry on an obtained tomographic image. Wave propagation signals were...
-
The influence of water and mineral oil on volumetric losses in the displacement pump for offshore and marine applications
PublikacjaIn this paper volumetric losses in a positive displacement pump supplied with water and mineral oil are described and compared. The experimental tests were conducted using a prototype of a satellite pump (with a non-circular tooth working mechanism). In this paper the sources of volumetric losses in this pump are characterised. On this basis, a mathematical model of these losses has been presented. The results of the calculation...
-
Smoothed transition curve for railways
PublikacjaThe work draws attention to the existing situation in the area of transition curves used in the geometric layouts of the railway track. Difficulties in the practical implementation and maintenance of very small horizontal ordinates of the transition curve and the ordinates of the gradient due to cant in the initial section, appearing on smooth transition curves, were indicated. The main reason for this situation was the excessive...
-
Inhibition of amyloid fibril formation of hen egg white lysozyme by trimethylamine N-oxide at low pH
PublikacjaIn vitro inhibition of the formation of fibrous aggregates of proteins (amyloids) has gained increasing attention due to the number of diseases associated with protein misfolding and fibrillation. An interesting group of compounds for which pronounced activity against this phenomenon can be expected consists of low molecular weight substances (osmolytes) which have the ability to change protein stability. Here we investigate the...
-
Participatory co-design approach for Greencoin educational tool shaping urban green behaviors.
PublikacjaOur main goal is to prepare assumptions of the Greencoin (GC) cybernetic system, implying pro-ecological attitudes and behavior of city residents. We used qualitative methods, including a literature review and action research -workshops attended by academics, representatives of private and business sectors, urban movements, municipal institutions’ partners, and residents. Our results defined functionalities of the GC, identified...
-
Sustainable energy system combined biogas-feedSolid Oxide Fuel Cell and Microalgae technology
PublikacjaIn the new frontier of energy and environmental safety, new efficient and clean safe energy conversion systems are required. In this sense, the present work is framed within the context of Circular Economy and proposes a multidisciplinary study for the development of more efficient, economically viable and non-polluting energy conversion systems, based on the synergetic combination of different technologies: fuel cells, biofuels,...
-
Modelling of Longitudinal Elastic Wave Propagation in a Steel Rod Using the Discrete Element Method
PublikacjaThe paper deals with the issue of modelling elastic wave propagation using the discrete element method (DEM). The case of a longitudinal wave in a rod with a circular cross-section was considered. A novel, complex algorithm consisting of the preparation of models and simulation of elastic waves was developed. A series of DEM models were prepared for simulations, differing in discretisation and material parameters. Additional calculations...
-
Compact Dual-Polarized Corrugated Horn Antenna for Satellite Communications
PublikacjaIn this paper, a structure and design procedure of a novel compact dual-polarized corrugated horn antenna with high gain and a stable phase center for satellite communication is presented. The antenna incorporates an Ortho-Mode Transducer (OMT), a mode converter, and a corrugated structure. The compact OMT section is designed to be fed by standard WR-75 waveguides. The proposed compact design utilizes only ten corrugated slots...
-
Ultra-Compact Self-Quadruplexing Microfluidically Frequency Reconfigurable Slot Antenna Using Half-Mode SIW
PublikacjaIn this brief, the design of an ultra-compact self-quadruplexing frequency reconfigurable antenna (SQFRA) utilizing a half-mode substrate-integrated waveguide (HMSIW) and microfluidic channels is discussed. Four HMSIW cavities fed by four microstrip lines and slots are used to construct a highly compact antenna. The microstrip feedings to the HMSIW cavities are applied in such a way that the proposed antenna exhibits self-quadruplexing...
-
Design and Optimization of Metamaterial-Based 5G Millimeter Wave Antenna for Gain Enhancement
PublikacjaIn this brief, a low profile, broadband, high-gain antenna array based on optimized metamaterials (MMs) with dual-beam radiation is reported for 5G millimeters wave (mm-wave) applications. The design is a simple bow tie operating at a 5G band of 28 GHz. It consists of two bow ties with substrate integrated waveguide (SIW)-based power splitter. A broad impedance bandwidth of 26.3−29.8 GHz is obtained by appropriately combining the...
-
A Microwave Sensor with Operating Band Selection to Detect Rotation and Proximity in the Rapid Prototyping Industry
PublikacjaThis paper presents a novel sensor for detecting and measuring angular rotation and proximity, intended for rapid prototyping machines. The sensor is based on a complementary split-ring resonator (CSRR) driven by a conductor-backed coplanar waveguide. The sensor has a planar topology, which makes it simple and cost-effective to produce and accurate in measuring both physical quantities. The sensor has two components, a rotor, and...
-
Analityczna weryfikacja dokładności komercyjnych programów komputerowych wspomagających projektowanie układów geometrycznych toru
PublikacjaW pracy podjęto próbę wyjaśnienia kwestii uzyskiwanej dokładności w projektowaniu układów geometrycznych toru z wykorzystaniem komercyjnych programów komputerowych typu CAD. Użytkownikowi najczęściej nie są znane zasady działania tych programów, w tym również wykorzystywane algorytmy obliczeniowe. Opisano w sposób ogólny funkcjonowanie dwóch wiodących programów. Przedstawiono własną, analityczną metodę projektowania układów torowych,...
-
Zjawisko przesłuchu w wieloprzewodowych prowadnicach koplanarnych
PublikacjaCelem pracy jest analiza zjawiska przesłuchu na bliskim i dalekim końcu sprzężonych linii koplanarnych (ang. Coupled Coplanar Waveguides C-CPW) i sprzężonych linii koplanarnych z centralnie umieszczonym uziemionym paskiem (ang. Coupled Coplanar Waveguides with central Grounded Strip C-CPWGS) o skończonej długości przy pobudzeniu falą prostokątną. Wymagało to stworzenia modeli numerycznych rozpatrywanych prowadnic i poddania ich...
-
New transition curve adapted to railway operational requirements
PublikacjaThe paper points to the limited possibilities of improving the existing situation in the area of transition curves used in geometrical layouts of the railway track. Difficulties in the practical implementation and maintenance of very small horizontal ordinates of the transition curve and the ordinates of the gradient due to cant in the initial section, appearing on smooth transition curves, were indicated. The main reason for this...
-
Inverse and forward surrogate models for expedited design optimization of unequal-power-split patch couplers
PublikacjaIn the paper, a procedure for precise and expedited design optimization of unequal power split patchcouplers is proposed. Our methodology aims at identifying the coupler dimensions that correspond to thecircuit operating at the requested frequency and featuring a required power split. At the same time, thedesign process is supposed to be computationally efficient. The proposed methodology involves two typesof auxiliary models (surrogates):...
-
Application of fracture mechanics for energetic effects predictions while wood sawing
PublikacjaIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (power) could be considered from a point of view of modern fracture mechanics. Cutting forces may be employed to determine not only toughness...
-
Self-Association of Amphotericin B: Spontaneous Formation of Molecular Structures Responsible for the Toxic Side Effects of the Antibiotic
PublikacjaAmphotericin B (AmB) is a lifesaving antibiotic used to treat deep-seated mycotic infections. Both the pharmaceutical activity and highly toxic side effects of the drug rely on its interaction with biomembranes, which is governed by the molecular organization of AmB. In the present work we present detailed analysis of self-assembly of AmB molecules in different environments, interesting from the physiological standpoint, based...
-
Energy and valuable organic products recovery from anaerobic processes
PublikacjaChapter 8 contains: Introduction, Energy balance in wastewater treatment plants and potential energy recovery, Potential valuable products recovery, Anaerobic processes focused on liquid products recovery; Anaerobic digestion (AD) processes focused on gaseous products recovery, Processes enhancing energy and valuable organic products recovery, Conclusions and perspectives. Anaerobic processes offer different pathways for the recovery...
-
Numerical Modelling of Forced Convection of Nanofluids in Smooth, Round Tubes: A Review
PublikacjaA comprehensive review of published works dealing with numerical modelling of forced convection heat transfer and hydrodynamics of nanofluids is presented. Due to the extensive literature, the review is limited to straight, smooth, circular tubes, as this is the basic geometry in shell-and-tube exchangers. Works on numerical modelling of forced convection in tubes are presented chronologically in the first part of the article....
-
Estimation of fracture toughness and shear yield stress of orthotropic materials in cutting with rotating tools
PublikacjaThe cutting force is an energetic effect of splitting material, and might be considered from a point of view of modern fracture mechanics. Forecasting of the shear plane angle in cutting broaden possibilities for modelling of the cutting process even for thin uncut chips. Such mathematical model has been developed here for description of the orthotropic materials’ cutting on the base of fracture theory, and includes work of separation...
-
CFFT columns in road through railroad crossings
PublikacjaThere were 12801 road through railroad one-level crossings in Poland in 2018. 215 accidents happened at them in 2018. In order to increase safety in rail and road traffic two-level crossings should be used. They are definitely safer and make the traffic more smooth. In the design and construction of two-level intersections of railway and road or path columns of circular cross-section are often used. They can be successfully replaced...
-
Multiaxial Fatigue Behaviour of SLM 18Ni300 Steel
PublikacjaFatigue behaviour of SLM 18Ni300 steel under proportional bending-torsion loading is studied. The fatigue tests are conducted under pulsating loading conditions using tubular specimens with a transversal circular hole. Three ratios of the normal stress to shear stress are considered, namely σ/τ=4,σ/τ=2 and σ/τ = 4/3. Crack initiation sites were found for two diametrically opposite points around the hole, whose locations are governed...
-
DETERMINATION OF THE HYDROXYL NUMBER OF GROUND TIRE RUBBER PARTICLES VIA MODIFIED TEST METHOD FOR ISOCYANATE GROUPS
PublikacjaNowadays, considering the environmental trends and law regulations associated with the circular economy, it is very important to seek for the methods of by-products and waste utilization. The example of such material, which requires the attention and recycling method is ground tire rubber generated during recycling of post-consumer car tires. It can be introduced into various polymer matrices as a filler, but to enhance its effectivity...
-
Shielded HMSIW-based frequency-tunable self-quadruplexing antenna using different solid/liquid dielectrics
PublikacjaThis article proposes a frequency-tunable self-quadruplexing antenna based on a shielded half-mode substrate integrated waveguide (S-HMSIW). In order to reduce the size of the HMSIW cavity resonator and to obtain quad-band characteristics, a modied E-shaped slot is engraved on the top of the metal. The experimental validation is carried out after analyzing the data using a circuit model. Flexibility of each resonant frequency is...
-
Design and Optimization of Metamaterial-based Highly-isolated MIMO Antenna with High Gain and Beam Tilting Ability for 5G Millimeter Wave Applications
PublikacjaThis paper presents a wideband multiple-input multiple-output (MIMO) antenna with high gain and isolation, as well as beam tilting capability, for 5G millimeter wave (MMW) applications. A single bow-tie antenna fed by a substrate-integrated waveguide (SIW) is proposed to cover the 28 GHz band (26.5–29.5 GHz) with a maximum gain of 6.35 dB. To enhance the gain, H-shaped metamaterial (MM)-based components are incorporated into the...
-
Highly Miniaturized Self-Diplexed U-Shaped Slot Antenna Based on Shielded QMSIW
PublikacjaThis article presents an efficient yet simple design approach to highly miniaturized cavity-backed self-diplexing antenna (SDA) with high-isolation. The structure employs a shielded quarter-mode substrate integrated waveguide (QMSIW). Two U-shaped slots are engraved on the top conducting plane, which realize two frequency bands and significant size reduction. The slots are excited by two independent 50Ω orthogonal feed-lines to...
-
Compact, Order Extensible and Wide-Stopband Bandpass Filter Based on SIW Cavity with Rectangular Ring Slot
PublikacjaThis article introduces novel architectures of bandpass filters (BPFs) using a substrate integrated waveguide (SIW) cavity with a rectangular ring slot (RRS) for compact size, extensible order, and broad stopband responses. Two bandpass filters, which demonstrate a second-and a fourth-order Chebyshev response, respectively, are realized by employing identical cavities with RRS, without increasing the physical size of the circuit....