Filtry
wszystkich: 589
-
Katalog
- Publikacje 506 wyników po odfiltrowaniu
- Czasopisma 11 wyników po odfiltrowaniu
- Wydawnictwa 1 wyników po odfiltrowaniu
- Osoby 9 wyników po odfiltrowaniu
- Projekty 10 wyników po odfiltrowaniu
- Kursy Online 15 wyników po odfiltrowaniu
- Wydarzenia 4 wyników po odfiltrowaniu
- Dane Badawcze 33 wyników po odfiltrowaniu
Wyniki wyszukiwania dla: ETHENE
-
Photocatalysts for Solar Energy Conversion
PublikacjaPhotocatalytic oxidation over suspended solid photocatalysts (e.g., titanium dioxide) has been proposed as a sustainable process for treatment and purification of water and wastewater as well as the process for photoconversion of solar energy to hydrogen, methane, and other low hydrocarbons. Solar radiation could be used to drive heterogeneous electrochemical reactions at the surface of an optically active photocatalyst (e.g.,...
-
Pulsed UV-irradiated Graphene Sensors for Ethanol Detection at Room Temperature
PublikacjaA graphene-based gas sensor fabricated in a FET (GFET) configuration and its sensitivity towards ethanol and methane is reported. Detection of ethanol at the level of 100 ppm was observed under pulsed UV irradiation and after cleaning by UV light in the N2 ambient. Reduction of the frequency of UV irradiation pulses resulted in increased changes in sensor resistance in the presence of ethanol. Improved sensing behavior was ascribed...
-
Sewage sludge pretreatment by low thermal disintegration for better efficacy of sludge digestion process
PublikacjaThe wastewater water treatment plant (WWTP) sector and it is developing technologies strive to be implement circular economy. The methane production from the sludge digestion process constitute promising source of the renewable energy for WWTP and approaching circular economy assumptions. For this reason, the objective of the study was to examine the modification of sludge characteristics due to the low temperature pretreatment....
-
Numerical simulation of natural convection of Glycol-Al2O3 nanofluids from a horizontal cylinder
PublikacjaThis paper deals with natural convection around a circular cylinder with constant heat flux in a cavity using computational fluid dynamics. As fluids ethylene glycol and a mixture of ethylene glycol with Al2O3 nanoparticles (mass concentrations of nanoparticles: 0.1% and 1%) are chosen. Rayleigh number ranges from 3104 to 3105. The nanofluids are modeled with single-phase approach. For the investigated range of nanoparticle concentration, the...
-
t-SNE Highlights Phylogenetic and Temporal Patterns of SARS-CoV-2 Spike and Nucleocapsid Protein Evolution
Publikacja -
Standard IEC 61850 w sieci rozdzielczej średniego napięcia CERN
PublikacjaArtykuł stanowi skrótowy opis wyników pracy autora w okresie od 01.10.2009 do 30.09.2010 w Engineering Department, High-Voltage Section w CERN. Przedstawiono system zasilania elektroenergetycznego obiektów CERN wraz automatyką ATS w sieci 18 kV. Zdefiniowano założenia dla automatyki w ramach planowanych modernizacji sieci średniego napięcia, wskazując na wymóg zgodności ze standardem IEC 61850. Zaproponowano trójpierścieniową topologię...
-
Oxygen sensitivity of hydrogenesis’ and methanogenesis’
PublikacjaIn the chapter, results of dark fermentation of sour cabbage in presence of oxygen with concentrations 2-9% are presented. The presence of oxygen in such concentration inhibits methanogesis (and methane production more than 2 times) and increases hydrogen production 6 times. It also shortens the fermentation process above 40%.
-
BDNF and Cortisol integrative system – Plasticity vs. degeneration: Implications of the Val66Met polymorphism
Publikacja -
Multi-state vibronic interactions in the fluorobenzene radical cation: The importance of quadratic coupling terms
PublikacjaThe multi-mode multi-state vibronic interactions in the set of X^2B_1 - D^2A_1 electronic states of the monofluoro benzene radical cation are investigated theoretically, based on a quadratic vibronic coupling approach. The underlying ionization potentials and coupling constants are obtained from ab initio coupled-cluster calculations. Previous investigations (relying on the linear coupling approach) are extended by including all...
-
eTEE 2017
Kursy Online -
Bioactive and bioavailability of minerals in rats loaded with cholesterol and kiwi fruit
PublikacjaThe aim of this study was to compare the content of polyphenols (TP), minerals, ascorbic acid (AA) and total antioxidant capacities (TAC) of conventional and organic kiwifruit ‘Hayward’ treated with ethylene after harvest and to determine their influence on plasma TAC, mineral content in the liver and bioavailability (RBV — relative bioavailability value) in rats fed diet containing cholesterol. Organic and conventionally grown...
-
Synthesis, structure and properties of novel poly(hydroxyurethane)s obtained by non-isocyanate route
PublikacjaNon-isocyanate polyurethanes (NIPUs) can be synthesized by polyaddition of five-membered bis(cyclic carbonate)s and primary diamines. NIPUs are an alternative for the commonly used (in the form of foams, elastomers, coatings or fibers) in the industry polyurethanes obtained using toxic and moisture sensitive diisocyanates, polyols and low-molecular weight chain extenders. The main aim of this work was to synthesize non-isocyanate...
-
The Influence of Low-Temperature Disintegration on the Co-Fermentation Process of Distillation Residue and Waste-Activated Sludge
Publikacja: Innovative low-temperature disintegration (process temperature 55 ◦C and oxygen concentration 0.2 mg/dm3 ) can be an economically rational technology to intensifying energy production from renewable sources. The proposed process can achieve a degree of disintegration—under optimal conditions—of about 50%, which is excellent when compared with other methods of feed pre-treatment. The low-temperature disintegration of distillation...
-
TOTAL CROSS SECTIONS FOR ELECTRON SCATTERING FROM SELECTED HYDROCARBONS: THE SUBSTITUTIONAL AND ADDITIVITY EFFECTS
PublikacjaTotal cross sections (TCS) for electron scattering from selected alkyne molecules, ethylene and its derivatives are compared. All cross sections have been measured in a wide energy range, from about 1 eV up to 370 eV, with the same electrostatic electron spectrometer. The substitutional and additivity effects are indicated and discussed.
-
Unusual behavior of secondary amine group as a leaving group
PublikacjaIn our recent project we focused on reactivity of2,2-dimethyl-4,6-dioxane-1,3-dione carbamoilo- and thiocarbamoylo- derivatives as a ketenesource. Meldrum`s acid derivatives after thermal decomposition gives substituted keteneswith stoichiometric yield, that can be trapped with various spectrum of nucleophiles likealcohols, thiols, amine, imines etc. In case of5-[3-(dimethylamino)-sulfanyl-propyliden]-2,2-dimethyl-1,3-dioxane-4,6-dione...
-
Ordered TiO2 nanotubes: the effect of preparation parameters on the photocatalytic activity in air purification process
PublikacjaVertically ordered TiO2 nanotube arrays were synthesized by anodic oxidation of titanium foil in glycerol, ethylene glycol and water-based electrolytes. The effect of electrolyte composition, anodization voltage, ultrasonic treatment and calcination time on the morphology of the resulting thin films, as well as on their photocatalytic activity in toluene removal, used as a model volatile organic compound, was investigated. Toluene,...
-
TOTAL CROSS SECTION MEASUREMENTS FOR ELECTRON SCATTERING ON METHYL FORMATE (HCOOCH3) MOLECULE: METHYLATION EFFECT
PublikacjaWe present the absolute total cross section (TCS) for electron scattering from the methyl formate (HCOOCH3) molecule measured in the 10-300 eV energy range, with electrostatic electron spectrometer working in the linear transmission mode. Comparison of TCS for the HCOOCH3 molecule with that measured earlier for the formic acid (HCOOH) compound manifests the methylation effect i.e. the response of the electron scattering dynamics...
-
Study of Aliphatic Polyurethanes by the Low-Field 1H NMR Relaxometry Method with the Inversion of the Integral Transformation
PublikacjaIn this paper, the distributions of the 1H nuclear magnetic resonance (NMR) spin–lattice and spin–spin relaxation times are used to characterize the mobility of different sections of macromolecules of aliphatic polyurethanes and the cross-linking density of polymer chains. The NMR relaxometry method with inversion of integral transformation is applied to study the effect of poly (ethylene glycol) and glycerol phosphate calcium...
-
Investigation of Thermoplastic Polyurethanes Synthesized via Two Different Prepolymers
PublikacjaThe man aim of this work was to investigate the effect of the molecular weight of polyols, mixture of prepolymers, and [NCO]/[OH] molar ratio used during the prepolymer chain extending step on the chemical structure, thermomechanical and mechanical properties, and thermal stability of thermoplastic poly(ether-urethane)s In this work thermoplastic poly(ether-urethane)s were synthesized by using polyols with a various molecular weight,...
-
Influence of Storage Time and Temperature on the Toxicity, Endocrine Potential, and Migration of Epoxy Resin Precursors in Extracts of Food Packaging Materials
PublikacjaThe aim of the present study was to establish a standard methodology for the extraction of epoxy resin precursors from several types of food packages (cans, multi-layered composite material, and cups) with selected simulation media (distilled water, 5% ethanol, 3% dimethyl sulfoxide, 5% acetic acid, artificial saliva) at different extraction times and temperatures (factors). Biological analyses were conducted to determine the acute...
-
Przegląd rodzajów chiralnych faz stacjonarnych oraz możliwości ich zastosowań w chromatografii cieczowej
PublikacjaChromatograficzne rozdzielanie związków optycznie czynnych ma ogromne znaczenie nie tylko w przemyśle farmaceutycznym, ale i agrochemicznym, a także w badaniach naukowych różnego rodzaju. W niniejszym opracowaniu scharakteryzowano komercyjnie dostępne chiralne fazy stacjonarne na bazie, cyklodekstryn, polisacharydów, makrocyklicznych antybiotyków, eterów koronowych, a także fazy proteinowe, ligandowymienne, jonowymienne oraz fazy...
-
Mechanizmy oszczędzania zużycia energii przez urzadzenia sieciowe
PublikacjaOmówiono zużycie energii elektrycznej przez urzšdzenia IT, w szczególnoci przez urzšdzenia sieciowe. Dokonano przeglšdu metod oszczędzania energii, w tym APM, ACPI, WOL, Power Management for ADSL. Przeanalizowano możliwoć wykorzystania mechanizmu autonegocjacji stosowanego w sieciach Ethernet do przełšczania szybkoci transmisji w celu oszczędzania zużycia energii.
-
One-step formation of n-alkenyl-malonamides and n-alkenyl-thiomalonamides from carbamoyl meldrum's acids.
PublikacjaA one-pot synthesis for the preparation of N-alkenyl-malonamides and N-alkenyl-thiomalonamides was developed. 5-[Hydroxy/mercapto(aryl/alkylamino)methylene]-2,2-dimethyl-1,3-dioxane-4,6-dione act as a source of ketenes that react with the tautomeric form of alkyl-(2-phenyl-propylidene)-amines. A possible [2+2] or [4+2] cycloaddition product of ketene to imines was not observed.
-
Mesophilic and thermophilic dark fermentation course analysis using sensor matrices and chromatographic techniques
PublikacjaProduction of biofuels from biomass is expected to benefit the society and the environment. At present, bio waste residues processing includes hydrolysis, dark fermentation, photofermentation, pyrolysis, gasification, and chemical synthesis. As the composition and the chemical structure of organic substances affect the efficiency of mentioned processes, it is believed that the glucose concentration is a crucial parameter for the...
-
Determination of Hydroxy Groups in the Modified Epoxy Oligomers Using IR-Spectroscopy
PublikacjaThe use of IR-spectroscopy has been proposed to determine the content of hydroxy groups in the modified functional oligomers based on bisphenol A diglycidyl ether. Apart from hydroxy groups the investigated oligomers contain epoxy or peroxy, carboxy or acrylic groups.
-
Wpływ produkcji butelek z tworzyw sztucznych na środowisko naturalne. Cz. I. Zastosowanie metody oceny ReCiPe 2016 w celu identyfikacji problemów środowiskowych
PublikacjaDokonano oceny wpływu opakowań na środowisko naturalne. Głównym celem było przeprowadzenie analizy cyklu życia (LCA) butelki do napojów wykonanej z poli(tereftalanu etylenu) (PET). Za jednostkę funkcjonalną przyjęto łącznie 1000 szt. butelek PET o pojemności 1 L. Granica przyjętego systemu obejmowała kroki od momentu dostarczenia preform do zakładu produkcyjnego aż do ich prawidłowego ukształtowania w procesie produkcyjnym. Z systemu...
-
Characterization of Optical and Electrical Properties of Transparent Conductive Boron-Doped Diamond thin Films Grown on Fused Silica
PublikacjaA conductive boron-doped diamond (BDD) grown on a fused silica/quartz has been investigated. Diamond thin films were deposited by the microwave plasma enhanced chemical vapor deposition (MW PECVD). The main parameters of the BDD synthesis, i.e. the methane admixture and the substrate temperature were investigated in detail. Preliminary studies of optical properties were performed to qualify an optimal CVD synthesis and film parameters...
-
The XRD diffraction patterns of as-preapred (La0.3Sr0.6Ce0.1)0.9FexTi(1-x)O3-δ (x=0.1, 0.2 and 0.3) materials
Dane BadawczeThe (La0.3Sr0.6Ce0.1)0.9FexTi(1-x)O3-δ (x=0.1, 0.2 and 0.3) materials were synthesized via the Pechini method. First, the reagents in the form of nitrates were weighed and dissolved in DI water. In another beaker, a stoichiometric amount of titanium (IV) butoxide (Ti(OBu)4) was mixed together with reagent-grade ethylene glycol (EG), and citric acid...
-
The XRD diffraction patterns of as-prepared (La0.3Sr0.6Ce0.1)0.9Me0.1Ti0.9O3-δ (Me= Co, Fe, Ni) materials
Dane BadawczeThe (La0.3Sr0.6Ce0.1)0.9Me0.1Ti0.9O3-δ (Me= Co, Fe, Ni) materials were synthesized via the Pechini method. First, the reagents in the form of nitrates were weighed and dissolved in DI water. In another beaker, a stoichiometric amount of titanium (IV) butoxide (Ti(OBu)4) was mixed together with reagent-grade ethylene glycol (EG), and citric acid (CA)...
-
The XRD diffraction patterns of as-prepared (La0.3Sr0.6Ce0.1)0.9Ni0.05Me0.05Ti0.9O3-δ (Me= Co, Fe, Cu) materials
Dane BadawczeThe ((La0.3Sr0.6Ce0.1)0.9Ni0.05Me0.05Ti0.9O3-δ (Me= Co, Fe, Cu) materials were synthesized via the Pechini method. First, the reagents in the form of nitrates were weighed and dissolved in DI water. In another beaker, a stoichiometric amount of titanium (IV) butoxide (Ti(OBu)4) was mixed together with reagent-grade ethylene glycol (EG), and citric acid...
-
The XRD diffraction patterns of as-prepared (La0.3Sr0.6Ce0.1)0.9FexMeyTi(1-x-y)O3-δ materials (Me=Ni,Co)
Dane BadawczeThe (La0.3Sr0.6Ce0.1)0.9FexMeyTi(1-x-y)O3-δ materials (Me=Ni,Co) were synthesized via the Pechini method. First, the reagents in the form of nitrates were weighed and dissolved in DI water. In another beaker, a stoichiometric amount of titanium (IV) butoxide (Ti(OBu)4) was mixed together with reagent-grade ethylene glycol (EG), and citric acid (CA)...
-
BDNF Val66Met Polymorphism, the Allele-Specific Analysis by qRT-PCR - a Novel Protocol
Publikacja -
On the Microstructure, Microhardnessand Wear Behavior of Gray Cast Iron Surface Layer after Laser Strengthening
Publikacja -
Evaluation of the Surface Topography of Ti6Al4V Alloy after the Finish Turning Process under Ecological Conditions
Publikacja -
Hydrogen Production via Biomethane Reforming in DBD Reactor
PublikacjaProduction of hydrogen from CH4:CO2 (70%:30%) mixture simulating dry biogas in a DBD reactor supplied with AC of 1.0-2.0 kHz or nanosecond negative pulses is presented. We have found that hydrogen production and methane conversion degree increase linearly with discharge power in the range of up to 50 W. Nanosecond voltage pulses are much more efficient in hydrogen production than sine AC voltage
-
The Effect of Long Term Service at Elevated Temperatures on Microstructure Degradation of Austenitic Reformer Tubes
PublikacjaThe paper analyses the relationship between an increase of the inner diameter of tubes made of Manaurite XM cast steel and transformations occurring in their microstructure due to long-lasting operation in methane reformer. Examinations included metallographic analysis with light microscope (LM), scanning electron microscope (SEM) and microanalysis of the chemical composition of precipitates (EDX). It was indicated that there is...
-
Chromium-Catalyzed CO2–Epoxide Copolymerization
PublikacjaIminopyrrole, aminopyrrole, and aminophosphine ligands were complexed with various chromium sources, producing eight complexes that were tested for their catalytic behavior toward epoxide–CO2 copolymerization. As elucidated by MALDI-TOF-MS, copolymerizations afforded polycarbonates and poly(ether-carbonates) exhibiting linear or cyclic topologies.
-
Standardy zasilania urządzeń sieci ethernetowych przez kable transmisyjne
PublikacjaW pracy wskazano na problemy zasilania urzadzeń sieciowych, w szczególności konieczność budowania dedykowanych systemów zasilających. Przedstawiono standard IEEE 802.3af (komercyjna nazwa - Power over Ethernet (PoE))specyfikujący zasady zasilania urządzeń końcowych przez standardowe kable ethernetowe. Omówiono zasady zasilania urzdzeń proponowane w standardzie PoE, wskazano na ograniczenia wprowadzone przez IEEE 802.3af, zaprezentowano...
-
Rigid polyurethane foams with different flame retardants and their physical and mechanical properties
PublikacjaRigid polyurethane foams (PUFs) containing 3, 6 or 9 % of one of of two selected fire retardants (FR): oligomeric ethyl ethylene phosphate (Fyrol PNX) and expandable graphite (EG) were prepared, inspected and compared to foam without that fillers as the control. The thermal stability of PUFs was described by horizontal test according to norm: UL 94 HB. Compressive strength and physical properties (density, fragility and water absorption)...
-
Wastes from Agricultural Silage Film Recycling Line as a Potential Polymer Materials
PublikacjaThe recycling of plastics is currently one of the most significant industrial challenges. Due to the enormous amounts of plastic wastes generated by various industry branches, it is essential to look for potential methods for their utilization. In the presented work, we investigated the recycling potential of wastes originated from the agricultural films recycling line. Their structure and properties were analyzed, and they were...
-
Thermoplastic polyurethanes with glycolysate intermediates from polyurethane waste recycling
PublikacjaThe polyol is a major component in polyurethane formulations and therefore introducing to the formulation recycled polyol (obtained during decomposition process) allows decreasing the usage of pure petrochemical components. In this work, thermoplastic polyurethanes were prepared using various mixtures of a petrochemical macrodiol poly(ethylene-butylene adipate)diol (PEBA) and a recycled glycolysate intermediate, called glycolysate...
-
Teoretyczno-doświadczalne modelowanie konwekcji wymuszonej nanocieczy
PublikacjaPrzedłożona rozprawa doktorska dotyczy badań eksperymentalnych oraz numerycznych konwekcji wymuszonej nanocieczy. Badane nanociecze wytworzone były z cieczy bazowych takich jak woda demineralizowana i mieszaniny wody z glikolem etylenowym w trzech proporcjach objętościowych 90:10, 80:20 i 60:40. Jako nanocząstki użyto Al2O3, a wytworzone nanociecze miały koncentracje masowe 0,1%, 1% i 5%. Wyznaczono eksperymentalnie dynamiczny...
-
When migrant men become more involved in household and childcare duties – the case of Polish migrants in Norway
Dane BadawczeIn our two studies, we focus on egalitarian attitudes towards genderrelations manifested by the readiness to share and actual share ofhousehold duties by Polish migrant couples in Norway, where wecompare their household arrangements with Polish couples inPoland to verify whether the migration to socio-democraticwelfare state country might encourage...
-
Novel Polyurethanes as Antifouling Paint Matrices
PublikacjaThe new poly(ester-ether urethane)s (PEEUR) were prepared in two stage synthesis from formerly obtained oligo(alkylene ester-ether)diols (OAEE) and 4,4‘-diphenylmethane diisocyanate (MDI). PEEUR samples were subjected to crosslinking with styrene in the presence of radical polymerization initiators: methyl ethyl ketone peroxide (MEKPO) or cobalt 2-ethyl cyclohexanoate (EtHCo). Crosslinked PEEUR were characterized by their physicochemical...
-
Synthesis of malonylenamides and thiomalonylenamides
Publikacja5-[Hydroksyl(aryl(amino))methylene]-2,2-dimethyl-1,3-dioxane-4,6-dione is convenient source of ketenes which can be trapped with various nucleophiles like alcohols, thiols and amines. In reaction between in situ generated ketene and enolizable imines we can easily obtain corresponding malonylenamides. This facile method can be used to obtain thiomalonylenamides using 5-[sulfhydrylo(alkyl(amino))methylene]-2,2-dimethyl-1,3-dioxane-4,6-dione...
-
Non-isocyanate Polyurethanes
PublikacjaThe main aim of this chapter is to present a general overview of the NIPU synthesis method (i.e., polycondensation and polyaddition), and to describe structure and properties of selected intermediates and final polymeric products. The focus is on five-membered ring cyclic carbonate intermediates, which were obtained by cycloaddition of carbon dioxide to selected glycidyl ethers and thiol-ene coupling of unsaturated cyclic carbonates...
-
Air flow phenomena in the model of the blind drift
PublikacjaIn the presented paper, Particle Image Velocimetry (PIV) has been used to investigate flow pattern and turbulent structure in the model of blind drift. The presented model exist in mining, and has been analyzed to resolve ventilation issues. Blind region is particularly susceptible to unsafe methane accumulation. The measurement system allows us to evaluate all components of the velocity vector in channel cross-section simultaneously....
-
Piotr Jaskuła dr hab. inż.
OsobyI am a Faculty member (Associate Professor, Highway and Transportation Research Department) at the Faculty of Civil and Environmental Engineering, Gdansk University of Technology, Poland).My main research interests include: pavement structures, interlayer bonding, pavement materials, recycling of road pavements, asphalt mixtures, bitumens, construction and maintenance of pavement structures.My lectures at the University include:...
-
GTR/Thermoplastics Blends: How Do Interfacial Interactions Govern Processing and Physico-Mechanical Properties?
PublikacjaIn this work, GTR/thermoplastics blends (in ratio 50/50 and 75/25 wt.%) were prepared by melt-compounding in an internal mixer. During research, trans-polyoctenamer rubber (TOR), ethylene-vinyl acetate copolymer (EVA), ethylene-octene copolymer (EOC), and linear low-density polyethylene (LLDPE), were used in their thermoplastic phase. Microstructure and processing-performance property interrelationships of the studied materials...
-
Experimental study on the effect of selected sterilization methods on mechanical properties of polylactide FFF specimens
PublikacjaPurpose: Biodegradable polymers are widely used in personalized medical devices or scaffolds for tissue engineering. The manufacturing process should be finished with sterilization procedure. However, it is not clear how the different sterilization methods have an impact on the mechanical strength of the three-dimensional (3D)-printed parts, such as bone models or personalized mechanical devices. This paper aims to present the...