Filtry
wszystkich: 1415
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: deceleration capacity
-
MgPd2Sb : A Mg-based Heusler-type superconductor
PublikacjaWe report the synthesis and physical properties of a full Heusler compound, MgPd2Sb, which we found toshow superconductivity belowTc=2.2K. MgPd2Sb was obtained by a two-step solid-state reaction methodand its purity and cubic crystal structure [Fm-3m,a=6.4523(1) Å] were confirmed by powder x-ray diffrac-tion. Normal and superconducting states were studied by electrical resistivity, magnetic susceptibility, andheat...
-
Prototype design and development of low-load-roof photovoltaic modules for applications in on-grid systems
PublikacjaFour prototypes of lightweight photovoltaic modules for applications in on-grid systems have been designed, developed, manufactured and tested for compliance with relevant IEC standards. Selected, commercially available materials characterized by thermogravimetry, differential scanning calorimetry, dilatometry, scanning electron microscopy and nanoindentation technique were used in frameless, adhesively-bonded sandwich-structures...
-
Hydraulic resistance analyses of selected elements of the prototype Stirling engine
PublikacjaThe paper presents the results of simulation tests of hydraulic resistance and temperature distribution of the prototype Stirling alpha engine supplied with waste heat. The following elements were analyzed: heater, regenerator and cooler. The engine uses compressed air as a working gas. Analyses were carried out for three working pressure values and different engine speeds. The work was carried out in order to optimize the configuration...
-
Transdermal transport of collagen and hyaluronic acid using water in oil microemulsion
PublikacjaCollagen and hyaluronic acid (HA) are biopolymers that affect the appearance and condition of the skin. Delivery of these compounds into the skin is highly challenging since have a number of disadvantageous properties, such as high molecular weight and hydrophilicity. Here, we evaluated the transdermal penetration of low and high molecular weight collagen and HA from microemulsions. A number of microemulsion formulations, differing...
-
Debonding Size Estimation in Reinforced Concrete Beams Using Guided Wave-Based Method
PublikacjaThe following paper presents the results of the theoretical and experimental analysis of the influence of debonding size on guided wave propagation in reinforced concrete beams. The main aim of the paper is a development of a novel, baseline-free method for determining the total area of debonding between steel rebar embedded in a concrete cover on the basis of the average wave velocity or the time of flight. The correctness of...
-
Use of Bi-Temporal ALS Point Clouds for Tree Removal Detection on Private Property in Racibórz, Poland
PublikacjaTrees growing on private property have become an essential part of urban green policies. In many places, restrictions are imposed on tree removal on private property. However, monitoring compliance of these regulations appears difficult due to a lack of reference data and public administration capacity. We assessed the impact of the temporary suspension of mandatory permits on tree removal, which was in force in 2017 in Poland,...
-
Automation of the Road Gate Operations Process at the Container Terminal—A Case Study of DCT Gdańsk SA
PublikacjaThe future increased terminal capacity will result in more container movement through the road complex and rail siding, which are one of the most critical areas (potential bottlenecks) in the container terminal. Truck turnaround time is one of the major factors that customers take into account while deciding how many container volumes they will handle through the container terminal. To enable to optimize increased traffic with...
-
Optimization of combined heat and power (CHP) market allocation: The case of Poland
PublikacjaCombined heat and power (CHP), that is production of electricity and useful heat in a single thermodynamic process, is a way of primary energy saving and emission reduction. Therefore, promotion of the electricity from high-efficiency cogeneration (CHP-E) was encouraged in the European Union. However, CHP-E promotion mechanisms proved low effectiveness in certain countries, like Poland, where the prices of certificates of origin...
-
Gender and Digital Divide - Information and Communication Technologiesand their Impact on Equality
PublikacjaIn the entire Europe more women than men graduate from tertiaryeducation institutes. However, they are underrepresented in scientific and engineering disciplines. Women researchers still constitute a minority in the Government and Higher Education Sectors. A number of industry reports highlight a low number of women in IT occupations49. This has led to a variety of public policy measures, such as subsidies on community provision,...
-
Analysis of unsteady flow forces on the thermowell of steam temperature sensor
PublikacjaIn this paper, 3D numerical analysis of unsteady flow forces acting on the measuring sheath of steam temperature is presented. According to that purpose, the CFD (Computation Fluid Dynamic [1]) approach has been used. The nonstationary of fluid acting on the measuring sheath such as: Strouhal frequency, amplitude of pressure, structure of vortex, peak of pressure, field of pressure, field of velocity etc. are studied analytically...
-
Wettability of shale rock as an indicator of fracturing fluid composition
PublikacjaShales have become one of the main unconventional gas resources in the world. However, physicochemical properties of rocks are still at the center of research. There have been conducted major researches in wettability of shales by fluids and advances in understanding and control of shale rock wettability. Also influence of interfacial phenomena on a production capacity of reservoirs have been made. The aim of this study is to find...
-
Influence of pyrolysis atmosphere on the lithium storage properties of carbon-rich polymer derived SiOC ceramic anodes
PublikacjaPolymer derived carbon-rich SiOC ceramics are prepared from polysiloxane precursors through a pyrolysis process at 1000 °C using pure argon and argon/hydrogen mixture as pyrolysis atmosphere. The precursor is synthesized from a linear (Si–H)-containing polysiloxane cross-linked with divinylbenzene using hydrosilylation reaction in the presence of a platinum catalyst. Pyrolysis in Ar/H2 mixtures, compared to the treatment under...
-
Biomedical engineering of polysaccharide-based tissue adhesives: Recent advances and future direction
PublikacjaTissue adhesives have been widely used for preventing wound leaks, sever bleeding, as well as for enhancing drug delivery and biosensing. However, only a few among suggested platforms cover the circumstances required for high-adhesion strength and biocompatibility, without toxicity. Antibacterial properties, controllable degradation, encapsulation capacity, detectability by image-guided procedures and affordable price are also...
-
A model, design, and implementation of an efficient multithreaded workflow execution engine with data streaming, caching, and storage constraints
PublikacjaThe paper proposes a model, design, and implementation of an efficient multithreaded engine for execution of distributed service-based workflows with data streaming defined on a per task basis. The implementation takes into account capacity constraints of the servers on which services are installed and the workflow data footprint if needed. Furthermore, it also considers storage space of the workflow execution engine and its cost....
-
Health-Promoting Effects of Ethylene-Treated Kiwifruit ‘Hayward’ from Conventional and Organic Crops in Rats Fed an Atherogenic Diet
PublikacjaKiwifruit is a subtropical fruit that is very popular among consumers. Kiwifruit ‘Hayward’ (Actinidia deliciosa C.F. Liang et A.R. Ferguson) is an important source of bioactive compounds and possesses high antioxidant capacity, but its value can be changed during ripening. The aim of this study was to compare the levels of total polyphenols (TP), ascorbic acid (AA), and total antioxidant capacities (TACs) of ethylene-treated and...
-
(CsX)Cu5O2(PO4)2 (X = Cl, Br, I): A Family of Cu2+ S = 1/2 Compounds with Capped-Kagomé Networks Composed of OCu4 Units
PublikacjaThree new salt inclusion compounds (CsX)Cu5O2(PO4)2 (X = Cl, Br, I), phosphate analogues of the kagomé mineral averievite, are reported. Their crystal structures are composed of trigonal networks of corner-sharing OCu4 anion-centered tetrahedra, forming capped-kagomé planes, which can also be regarded as two-dimensional slices along the [111] direction of a pyrochlore lattice. Magnetization and heat capacity measurements reveal...
-
Preparation and Characterization of Nanomaterial Consisting of Silica Aerogel & Carbon Tested as an Electrode in Non-Aqueous Media Containing Lithium Salt.
PublikacjaSilica aerogel (SiO2ag) was combined with carbonaceous material in the pyrolysis process of hydrocarbons. The obtained nanocomposite SiO2ag/C was amorphous, partially preserving the porous structure of SiO2ag. The specific surface area changes from 445.6 m2/g for pure SiO2ag to 205.52 m2/g SiO2ag/C. The 29Si MAS-NMR shows a three-dimensional matrix with silicon atoms connected to other silicon atoms by four...
-
Rattling-enhanced superconductivity in MV2Al20 (M = Sc, Lu, Y) intermetallic cage compounds
PublikacjaPolycrystalline samples of four intermetallic compounds: MV2Al20 (M=Sc, Y, La, and Lu) were synthesized using an arc-melting technique. The crystal structures were analyzed by means of powder x-ray diffraction and Rietveld analysis, and the physical properties were studied by means of heat capacity, electrical resistivity, and magnetic susceptibility measurements down to 0.4 K. For ScV2Al20, LuV2Al20, and YV2Al20, superconductivity...
-
Investigation of stability and limit load of a truss overhead opened bridge
PublikacjaThe paper presents selected methods of determining stability and limit load of a truss top chord in opened bridges. These methods include linear buckling and non-linear static analysis based on the finite element method and algorithms based on design code procedures. The described methods were tested on an example of a steel footbridge situated in Straszyn. The results of stability analysis are compared. The results of geometrical...
-
Point cloud based surface analysis of prestressed concrete element in exceeded state of serviceability
PublikacjaBy definition, serviceability state is characterized by the fact that despite meeting the requirements associated with carrying capacity, the object is not suitable for use. Serviceability limit state refers to factors, such as durability, overall stability, fire resistance, cracking, excessive vibration. Perfect examples of exceeded serviceability state are the improper vibration of a skyscraper, which inhabitants may suffer from...
-
Using Redis supported by NVRAM in HPC applications
PublikacjaNowadays, the efficiency of storage systems is a bottleneck in many modern HPC clusters. High performance in the traditional approach – processing using files – is often difficult to obtain because of a model’s complexity and its read/write patterns. An alternative approach is to apply a key-value database, which usually has low latency and scales well. On the other hand, many key-value stores suffer from a limitation of memory...
-
Biosilica from sea water diatoms algae—electrochemical impedance spectroscopy study
PublikacjaHere, we report on an electrochemical impedance study of silica of organic origin as an active electrode material. The electrode material obtained from carbonized marine biomass containing nanoporous diatoms has been characterised by means of XRD, IR, SEM and EIS. Dif- ferent kinds of crystallographic phases of silica as a result of thermal treatment have been found. The electrode is electrochemically stable during subsequent cyclic...
-
Interdependence between Power Grids and Communication Networks: A Resilience Perspective
PublikacjaPower network resilience is increasingly dependent on communication networks. Besides traditional generation, power networks need to accommodate increasingly high penetration levels of dispersed micro generation, mostly based on renewable sources, and increasing and challenging demand, such as electric vehicles. At the same time the deployment of enabling technologies throughout the power grid makes available new demand resources...
-
Application of electrochemical impedance spectroscopy to monitoring discharging process of nickel/metal hydride battery.
PublikacjaThis paper presents the possibility of applying impedance analysis to cell diagnostics. In order to obtain characteristic curves of both electrodes of a NiMH battery simultaneously, a reference electrode was added into the circuit. The authors analysed the cell under three cases, i.e. when its properties are determined only by the state of the positive electrode, only by the state of the negative electrode, or when both electrodes...
-
The Effect of C45 Carbon Black-Phosphomolybdic Acid Nanocomposite on Hydrogenation and Corrosion Resistance of La2Ni9Co Hydrogen Storage Alloy
PublikacjaIn this paper, we analysed the influence of corrosion processes and the addition of a carbon black-heteropoly phosphomolybdic acid (C45-MPA) nanocomposite on the operating parameters of a hydride electrode obtained on the basis of the intermetallic compound La2Ni9Co. The electrochemical properties of negative electrodes for NiMH batteries were studied using galvanostatic charge/discharge curves, the potentiostatic method, and electrochemical...
-
Optimized Computational Intelligence Model for Estimating the Flexural Behavior of Composite Shear Walls
PublikacjaThis article presents a novel approach to estimate the flexural capacity of reinforced concrete-filled composite plate shear walls using an optimized computational intelligence model. The proposed model was developed and validated based on 47 laboratory data points and the Transit Search (TS) optimization algorithm. Using 80% of the experimental dataset, the optimized model was selected by determining the unknown coefficients of...
-
Optimization of adsorption of methyl orange from aqueous solution by magnetic CoFe2O4/ZnAl-layered double hydroxide composite using response surface methodology
PublikacjaThe CoFe2O4/ZnAl-layered double hydroxide (LDH) composite was successfully developed through a facile co-precipitation method, characterized, and applied as an effective adsorbent for the removal of methyl orange (MO) dye from aqueous solutions. The central composite design (CCD) of the response surface methodology (RSM) was employed to estimate and optimize process variables such as initial MO concentrations, solution pH, adsorbent...
-
Properties of some fruit wines
PublikacjaRecently wereported about theconsumption of redwines fromgrapes, havingseveral health properties. Thereare different types of wines that originated fromgrapesand other fruits. In the present study fruit wines frompersimmon, kiwifruit and pomegranatewereinvestigated and compared for theirantioxidant ability, usingcupricion reducingantioxidant capacity (CUPRAC)and the 2,2-diphenyl-1-picrylhydrazyl (DPPH)assays. To thefruit wines...
-
9,10-Dioxoanthracenyldithiocarbamates effectively inhibit the proliferation of non-small cell lung cancer by targeting multiple protein tyrosine kinases
PublikacjaAnthraquinones have attracted considerable interest in the realm of cancer treatment owing to their potent anticancer properties. This study evaluates the potential of a series of new anthraquinone derivatives as anticancer agents for non-small-cell lung cancer (NSCLC). The compounds were subjected to a range of tests to assess their cytotoxic and apoptotic properties, ability to inhibit colony formation, pro-DNA damage functions,...
-
Modeling of Electrified Transportation Systems Featuring Multiple Vehicles and Complex Power Supply Layout
PublikacjaThe paper proposes a novel approach to modeling electrified transportation systems. The proposed solution reflects the mechanical dynamics of vehicles as well as the distribution and losses of electric supply. Moreover, energy conversion losses between the mechanical and electrical subsystems and their bilateral influences are included. Such a complete model makes it possible to replicate, e.g., the impact of voltage drops on vehicle...
-
Seismic damage diagnosis in adjacent steel and RC MRFs considering pounding effects through improved wavelet-based damage-sensitive feature
PublikacjaThis paper aims to propose complex Morlet (cmorfb-fc) wavelet-based refined damage-sensitive feature (rDSF) as a new and more precise damage indicator to diagnose seismic damages in adjacent steel and Reinforced Concrete (RC) Moment Resisting Frames (MRFs) assuming pounding conditions using acceleration responses. The considered structures include 6- and 9-story steel and 4- and 8-story RC benchmark MRFs that are assumed to have...
-
Mechanical simulation of artificial gravity in torus-shaped and cylindrical spacecraft
PublikacjaLarge deformations and stress analyses in two types of space structures that are intended for people to live in space have been studied in this research. The structure under analysis is assumed to rotate around the central axis to create artificial gravitational acceleration equal to the gravity on the Earth's surface. The analysis is fully dynamic, which is formulated based on the energy method by using the first-order shear deformation...
-
Computationally-efficient design optimisation of antennas by accelerated gradient search with sensitivity and design change monitoring
PublikacjaElectromagnetic (EM) simulation tools are of primary importance in the design of contemporary antennas. The necessity of accurate performance evaluation of complex structures is a reason why the final tuning of antenna dimensions, aimed at improvement of electrical and field characteristics, needs to be based on EM analysis. Design automation is highly desirable and can be achieved by coupling EM solvers with numerical optimisation...
-
Nondestructive Testing of the Miter Gates Using Various Measurement Methods
PublikacjaWhen any problems related to civil engineering structures appear, identifying the issue through the usage of only one measuring method is difficult. Therefore, comprehensive tests are required to identify the main source. The strains and displacement measurements, as well as modal identification, are widely used in the nondestructive testing of structures. However, measurements are usually carried out at several points and confirm...
-
A multiparameter simulation-driven analysis of ship response when turning concerning a required number of irregular wave realizations
PublikacjaThe growing implementation of Decision Support Systems on modern ships, digital-twin technology, and the introduction of autonomous vessels cause the marine industry to seek accurate modeling of vessel response. Despite the contemporary 6DOF models can be used to predict ship motions in irregular waves, the impact of their stochastic realization is usually neglected and remains under-investigated. Especially in the case of turning, differences...
-
Injectable poloxamer/graphene oxide hydrogels with well‐controlled mechanical and rheological properties
PublikacjaAlthough significant progress has been made in the design and application of injectable hydrogels for biomedical applications, concurrent control of rheological and mechanical properties of injectable hydrogels has remained as an open challenge to the researchers. In this work, we introduce and put into practice a photo‐curable poloxamer (also known as Pluronic)/graphene oxide (Plu/GO) injectable hydrogel with well‐controlled rheological...
-
Numerical Investigation on Dynamic Performance of a Multi-storey Steel Structure Model and Comparison with Experimental Results
PublikacjaShaking table testing is the most commonly adopted method to simulate earthquake forces. This approach allows us to analyze the dynamic performance and provides a valuable insight into the dynamics of building structures, which helps to improve their future safety and reliability. The present study aims to conduct a numerical evaluation of dynamic response of a multi-storey steel structure model, which was previously examined during...
-
Numerical investigation on dynamic performance of a multi-storey steel structure model and comparison with experimental results
PublikacjaShaking table testing is the most commonly adopted method to simulate earthquake forces. This approach allows us to analyze the dynamic performance and provides a valuable insight into the dynamics of building structures, which helps to improve their future safety and reliability. The present study aims to conduct a numerical evaluation of dynamic response of a multi-storey steel structure model, which was previously examined during...
-
Mutual Coupling Reduction in Antenna Arrays Using Artificial Intelligence Approach and Inverse Neural Network Surrogates
PublikacjaThis paper presents a novel approach to reduce undesirable coupling in antenna arrays using custom-designed resonators and inverse surrogate modeling. To illustrate the concept, two stand-ard patch antenna cells with 0.07λ edge-to-edge distance are designed and fabricated to operate at 2.45 GHz. A stepped-impedance resonator is applied between the antennas to suppress their mutual coupling. For the first time, the optimum values...
-
Eksperymentalna weryfikacja procedury szacowania wytrzymałości młodego betonu wg normy ASTM C1074
PublikacjaW referacie przedstawiono metodę służącą oszacowaniu wytrzymałości betonu w trakcie procesu dojrzewania (ang. Maturity Method) bazującą na procedurze określonej zgodnie z amerykańską normą, która uwzględnia wpływ połączonych efektów temperatury i czasu na rozwój wytrzymałości betonu. Standardy ASTM C1074 zostały opracowane przez NBS (ang. National Bureau of Standards) z uwagi na powtarzające się wypadki na palcu budowy wynikające...
-
Improving Thermal Insulation Properties for Prefabricated Wall Components Made of Lightweight Aggregate Concrete with Open Structure
PublikacjaPorous concrete is commonly used in civil engineering due to its good thermal insulation properties in comparison with normal concrete and high compression strength in comparison with other building materials. An extremely porous concrete, called ‘lightweight aggregate concrete with open structure’ (LAC), is used in some German plants to produce prefabricated wall components. They are used mainly in hall buildings, e.g. supermarkets....
-
Permanent traffic count stations - expressway S6 Poland 2016
Dane BadawczeThe data includes traffic data from permanent traffic count stations located on the expressway S6 in the Tri-City Agglomeration area in Poland. The data covers the 12 months of 2016.
-
Video traffic data - Interchange Bielany (A4-5) - weaving, Poland
Dane BadawczeThe data includes video traffic data registered with 12 video cameras at weaving area (weaving section type A) of the Bielany interchange within A4 motorway in Poland (interchange of motorway A4 and nacional road 5), located in the Silesian Agglomeration.The data covers the one day: 07.06.2017 (motorway A4)
-
Video traffic data - Interchanges Wolnosci (86 - 94)
Dane BadawczeThe data includes video traffic data registered with 3 video cameras at entry or exit lanes of the Wolnosci interchange within 86 national road in Poland (interchange of national roads 86 and 94 ), located in the Silesian Agglomeration). The data covers the one days: 22.05.201 (national road 86).
-
Video traffic data - Interchange Slowackiego (S8-Slowackiego), Poland
Dane BadawczeThe data includes video traffic data registered with 4 video cameras at entry or exit lanes of the Slowackiego interchange within S8 expressway in Poland (interchange of expressway S8 and Slowackiego street), located in the Warsaw Agglomeration. The data covers the one day: 10-11.05.2017 (expressway S8).
-
Video traffic data - Interchange Tychy (1-44), Poland
Dane BadawczeThe data includes video traffic data registered with 8 video cameras at weaving area (weaving section type A) of the Tychy interchange within national road 1 in Poland (interchange of national roads 1 and 44), located in the Silesian Agglomeration. The data covers the two days:13-14.09.2017.
-
Video traffic data - Interchange Broniewskiego (S8-Broniewskiego), Poland
Dane BadawczeThe data includes video traffic data registered with 4 video cameras at entry or exit lanes of the Broniewskiego interchange within S8 expressway in Poland (interchange of expressway S8 and Broniewskiego street), located in the Warsaw Agglomeration. The data covers the two days: 10-11.05.2017 (expressway S8).
-
Wpływ zmian dopuszczalnych wartości parametrów geometrycznych i kinematycznych na podatność modernizacyjną układów torowych
PublikacjaPodatnością modernizacyjną nazywamy stopień przystosowania analizowanego odcinka linii kolejowej do zmiany prędkości eksploatacyjnej. Skala możliwych zmian prędkości (w sensie jej zwiększenia) jest wypadkową istniejącego układu geometrycznego linii w planie, ograniczeń lokalizacyjnych oraz dopuszczalnych wartości parametrów geometrycznych i inematycznych. Jakiekolwiek zmiany tych ostatnich wpływają bezpośrednio na obliczenie elementarnych...
-
Metal-Organic Framework (MOF)/Epoxy Coatings: A Review
PublikacjaEpoxy coatings are developing fast in order to meet the requirements of advanced materials and systems. Progress in nanomaterial science and technology has opened a new era of engineering for tailoring the bulk and surface properties of organic coatings, e.g., adhesion to the substrate, anti-corrosion, mechanical, flame-retardant, and self-healing characteristics. Metal-organic frameworks (MOFs), a subclass of coordinative polymers...
-
Influence of the Shear Cap Size and Stiffness on the Distribution of Shear Forces in Flat Slabs
PublikacjaThe scope of this paper is to investigate analytically and numerically the influence of shear cap size and stiffness on the distribution of shear forces in flat slabs in a slab–column-connections-reinforced concrete structure. The effect of support (shear cap) stiffness on the calculation of the length of the shear control perimeter according to the available methods is presented. Based on the analysis, the authors indicate in...