Search
Filters
total: 1376
filtered: 987
Search results for: SHIP IC ENGINE
-
Robustly feasible integral LQ-MPC controller for output tracking in constrained linear systems
PublicationW pracy rozważany jest regulator predykcyjny typu dual-mode MPC z liniowo kwadratowym wskaźnikiem jakości w aplikacji do krzepkiego śledzenia wyjść liniowego obiektu dyskretnego w obecności addytywnych zakłóceń. W celu zapewnienia dopuszczalności sterowań regulatora wykorzystano teorię zbiorów niezmienniczych. W celu polepszenia śledzenia wyjść i odrzucenia zakłóceń w regulatorze wykorzystano działanie całkujące (integral control)....
-
Wykorzystanie środowiska ekspertowego do projektowania wybranych podsystemów energetycznych statków
PublicationW artykule przedstawiono koncepcję wykorzystania badań symulacyjnych oraz systemu ekspertowego z bazą wiedzy do wspomagania projektowania podsystemów energetycznych statków. Opisano przykładową strukturą steru strumieniowego oraz poszczególne jej elementy składowe.This paper presents a concept of application of simulation investigations and an expert system with a knowledge-base and data-base to improve design procedures of a ship...
-
Navigational decision support system during approach manoeuvre in emergency STS transfer operation
PublicationThe paper is concerned with the problem of safe trajectory planning for approaching during emergency STS (Ship to Ship) transfer operation with oil spill. The safe trajectory means that the way points does not cross in the area of the environment with the static and dynamic obstacles and at the same time satisfies ship's stopping and speed deceleration performance. The evolutionary path planning algorithm is used to determine trajectory...
-
Structural analysis of a wheeled tractor oriented towards damage diagnostics
PublicationThis study analyses the structure of a wheeled tractor whith the aim of evaluating the available options for diagnosing four types of defects affecting the vehicle's functions, exhaust gas emissions, engine performance and safety.
-
Analysis of diagnostic informativeness of the exhaust temperature of a naval gas turbine
PublicationThe conducted investigations aimed to carry out an analysis of the possibility that the failures identification in the automatic control system of a gas turbine engine could be worked out on the basis of measurements of the exhaust stream temperature behind the gas generator. The exhaust temperature represents a basic control parameter, enabling technical state evaluation of the engine within the operation process, which is observed...
-
A socially responsible university - an attempt to approach the system
PublicationIt is the author's thesis that social responsibility of university is an integrated system of both knowledge management (KM), quality management (QM) and organizational development (OD) processes. The author determined that the university "bond" is an institutional culture (IC). An integrated system is the way to create university an open system co-operated and co-opetited with stakeholders. The stakes are high in game - both students...
-
Ocena wpływu dawki DME na wybrane wskaźniki procesu spalania w dwupaliwowym silniku o zapłonie samoczynnym
PublicationPrzedmiotem rozprawy jest analiza wpływu różnej ilości odparowanego DME wprowadzonego do kolektora dolotowego na wybrane wskaźniki spalania DME/ON dla wielu punktów pracy, turbodoładowanego silnika o zapłonie samoczynnym. Jako punkty pracy silnika, wybrano punkty najbardziej reprezentujące cykl jazdy WLTP dla samochodu Volkswagen Golf IV. Analizę procesu współspalania przeprowadzono z wykorzystaniem danych pomiarowych, uzyskanych...
-
A decision-making system supporting selection of commanded outputs for a ship's propulsion system with a controllable pitch propeller
PublicationThe ship's operators have to make decisions regarding the values of commanded outputs (commanded engine speed and pitch ratio) which ensure maximum vessel speed and minimum fuel consumption. Obviously, the presented decision problems are opposed. Therefore, there is a need for a compromise solution that enables more flexible vessel voyage planning. This paper deals with development of a computer-aided system supporting selection...
-
Zastosowanie redundancji w siłowniach okrętowych statków oceanotechnicznych
PublicationSystemy wytwarzania energii i napędu statków oceanotechnicznych muszą mieć bardzo wysoki poziom niezawodności. Utrata zdolności do wykonywania funkcji przez ich elementy strukturalne z reguły powoduje bardzo wysokie straty ekonomiczne. Straty te mogą być zwiększone przez niemożność wykorzystania tzw. okna pogodowego, skutkującego odłożeniem w czasie zaplanowanych operacji oceanotechnicznych. W celu zapewnienia niezawodnej realizacji...
-
The Hough transform in the classification process of inland ships
PublicationThis article presents an analysis of the possibilities of using image processing methods for feature extraction that allows kNN classification based on a ship’s image delivered from an on-water video surveillance system. The subject of the analysis is the Hough transform which enables the detection of straight lines in an image. The recognized straight lines and the information about them serve as features in the classification...
-
Adaptive system for recognition of sounds indicating threats to security of people and property employing parallel processing of audio data streams
PublicationA system for recognition of threatening acoustic events employing parallel processing on a supercomputing cluster is featured. The methods for detection, parameterization and classication of acoustic events are introduced. The recognition engine is based onthreshold-based detection with adaptive threshold and Support Vector Machine classifcation. Spectral, temporal and mel-frequency descriptors are used as signal features. The...
-
Variations of Ship’s Deck Elevation Due to Stochastic Process of Containers Loading
PublicationThe stochastic process of container loading is described in the paper with special emphasis to ship motion when she is lying at a quay. The 3 DOF system was applied to describe rolling, pitching and heaving of a vessel which may cause a significant variations of momentary deck elevation. The realistic range of such variations are assessed for a variety of cargo locations on-board and a phase shift between two independent gantries...
-
Influence of lubricating oil improvers on performance of crankshaft seals
PublicationThis paper presents an original method for checking influence of lubricating oil improvers on performance of crankshaft seals of combustion piston engine. Crankshaft seals were tested with the use of a modified friction node of T-02 four- ball apparatus in laboratory conditions. The tests were conducted according to a worked-out algorithm. Their results confirmed usefulness of the method for determining „harmful” performance...
-
Integrated controller for ultra high frequency technique laboratory
PublicationDepartment of Microwave and Antenna Engineering decided to modernize the laboratory of Ultra High Frequency Techniques. The main change was to replace measurement of the field distribution inside rectangular waveguides by analysing the fields around striplines. This involved the need to overcome several technical and conceptual problems. Precise positioning of the probe and reading the field distribution near the stripline is important...
-
Development of an Analytical Protocol for Determination of Cyanide in Human Biological Samples Based on Application of Ion Chromatography with Pulsed Amperometric Detection
PublicationA simple and accurate ion chromatography (IC) method with pulsed amperometric detection (PAD) was proposed for the determination of cyanide ion in urine, sweat, and saliva samples. The sample pretreatment relies on alkaline digestion and application of Dionex OnGuard II H cartridge. Under the optimized conditions, the method showed good linearity in the range of 1–100 μg/L for urine, 5–100 μg/L for saliva, and 3–100 μg/L for sweat...
-
Importance of model tests in design and operation of watercraft for example CTO
PublicationShip Hydromechanics Division is a specialized research and development department of Ship Design and Research Centre conducting tests and research in the field of hydromechanics, connected with design and operation of ships and other floating structures, in scope of: predictions, numerical analyses, designs of - hull shape optimized with respect to the ship’s functions with the application of modern design tools, screw propellers...
-
Shipping Low Frequency Noise and Its Propagation in Shallow Water
PublicationOne of the most significant factor influencing acoustical climate of the sea is underwater noise generated by moving ships. If the considered sea area has features of the shallow water, namely the wave frequency fulfils relation f < 10c/h, where c denotes phase speed of sound, and h is depths of the sea, then in certain distance from the wave source specific image of sound pressure distribution in the mean of wave modes appears....
-
Impact of trajectory simplification methods on modeling carbon dioxide emissions from ships
PublicationModels of ship fuel consumption and emissions play an essential role in estimating global shipping’s greenhouse gas emissions. They are also widely used for verification of reported CO2 emissions for systems like EU MRV (Monitoring, Reporting and Verification) or IMO DCS (Data Collection System). Such models achieve high accuracy using historical spatiotemporal information about each ship from AIS data. However, this approach requires substantial...
-
The instantaneous frequency rate spectogram
PublicationAn accelerogram of the instantaneous phase of signal components referred to as an instantaneous frequency rate spectrogram (IFRS) is presented as a joint time-frequency distribution. The distribution is directly obtained by processing the short-time Fourier transform (STFT) locally. A novel approach to amplitude demodulation based upon the reassignment method is introduced as a useful by-product. Additionally, an estimator of energy...
-
Stirling engines powered by renewable energy sources
PublicationStirling engine is a device that produces mechanical energy using heat from any source of energy, without the need of combustion of any fuel inside the device. Renewable energy sources, which are mostly low-temperature energy sources, can be used to produce mechanical and electrical energy in Stirling engines. The paper presents an overview of the existing prototype Stirling engines designed for using of low-temperature energy...
-
Centrifugal magnetic fluid seals
PublicationSeals perform an important and at times overlooked function in a lubricant system. They prevent or minimize the movement of the lubricant between two surfaces and also minimize the level of contamination in the system. Seals are divided into static and dynamic types. Static seals operate in systems where the mating surfaces do not move relative to each other. In contrast, dynamic seals operate under conditions where the mating surfaces...
-
Wybrane problemy ochrony żeglugi (Maritime Security)
Publicationprzedstawiono zagadnienia ochrony żeglugi w aspekcie uwarunkowań związanych z radiokomunikacją morską. Opisano Międzynarodowy Kodeks Ochrony Statków i Urządzeń Portowych - ISPS (International Ship and Port Facility Security Code) i Statkowy System Alarmowania - SSAS (Ship Security Alert System) oraz także scharakteryzowano system AIS (Automated Information System) i System Identyfikacji i Śledzenia Dalekiego Zasięgu - LRIT (Long...
-
Application of theory of semi-Markov processes to determining distribution of probabilistic process of marine accidents resulting from colission of ships
PublicationIn this paper is presented possible application of the theory of semi-Markov processes to elaborating an eight-state model of the process of occurrence of serviceability state and unserviceability states of sea-going ships making critical manoeuvres during their entering and leaving the ports. In the analysis it was taken into account that sea-going ships are in service for a very long time t (t → ∞). The model was elaborated to...
-
SAMOCHÓD SPORTOWY DUOMOTO NAPĘDZANY DWOMA SILNIKAMI SPALINOWYMI
PublicationPrzedstawiono zaprojektowany i zbudowany przez zespół czterech dyplomantów Wydziału Mechanicznego Politechniki Gdańskiej samochód sportowy napędzany dwoma silnikami. Jeden z nich umieszczono z przodu pojazdu. Przekazuje on moment obrotowy na koła osi przedniej poprzez zespolony układ napędowy. Drugi silnik, usytuowany ztyłu pojazdu, w identyczny sposób przekazuje moment napędowy na koła osi tylnej....
-
Validation of atmospheric aerosols sampling in equivalent fractions
PublicationPhysical properties and chemical composition of atmospheric aerosols are of extreme importance, in many fields of interest, namely the Environment even with legal implications. Atmospheric sampling poses inherent problems with consequent demands on sampling optimisation, with sampling strategies requiring validation. In this work a study was conducted aiming at validating the collection of atmospheric aerosols in equivalent fractions....
-
Widening of the electroactivity potential range by composite formation – capacitive properties of TiO2/BiVO4/PEDOT:PSS electrodes in contact with an aqueous electrolyte
PublicationComposites based on the titania nanotubes were tested in aqueous electrolyte as a potential electrode material for energy storage devices. The nanotubular morphology of TiO2 was obtained by Ti anodization. TiO2 nanotubes were covered by a thin layer of bismuth vanadate using pulsed laser deposition. The formation of the TiO2/BiVO4 junction leads to enhancement of pseudocapacitance in the cathodic potential range. The third component,...
-
Application Isssues of the Semi-Markov Reliability Model
PublicationPredicting the reliability of marine internal combustion engines, for instance, is of particular importance, as it makes it possible to predict their future reliability states based on the information on the past states. Correct reliability prediction is a complex process which consists in processing empirical results obtained from operating practice, complemented by analytical considerations. The process of technical state changes...
-
ECU calibration for gaseous dual fuel supply system in compression ignition engines
PublicationThe dual fuel (DF) combustion mode is proven solution that allows to improve or get at the same level engine performance and reduce toxic compounds in exhaust gases which is confirmed by researchers and end-users. DF combustion mode uses two fuels gaseous fuel as a primary energy source and a pilot quantity of diesel fuel as ignition source. However, in order, to fully take advantage of the potential of the dual fuel mode, DF system...
-
Postquarter-Point Case of Ship’s Side-Berthing and Its Influence on Marine Fender Pitch
PublicationThis paper presents a critical analysis of some selected codes and practical recommendations used as basic rules in the design procedures of modern marine fender systems. The first part of the discussion pertains to the existing equations used in calculating the eccentricity coefficient in the ship’s kinetic energy equation and the maximum allowable fender pitch (spacing) in a set of fenders installed along a quay wall. A new approach...
-
A framework for onboard assessment and monitoring of flooding risk due to open watertight doors for passenger ships
PublicationPost-accident safety of ships is governed by damage stability, affected by watertight subdivisions which limit accidental flooding. This is important for passenger ships with watertight doors (WTDs) often fitted in the bulkheads. Awareness of the ship flooding risk due to open WTDs and the conditions under which the associated risk level changes are prerequisites for proactive risk mitigation. Accident risk is often expressed as...
-
Magnetic signature reproduction of ferromagnetic ships at arbitrary geographical position, direction and depth using a multi-dipole model
PublicationThe reproduction of magnetic signatures is an important issue concerning the safety of ship traffic, as well as the identification and classification of vessels. Moreover, military applications of magnetic signatures and their reproduction refer to the activation or protection against activation of magnetic naval mines. Previous works on this subject focused on recording and replicating the signatures under the same conditions...
-
TEORIA DECYZYJNYCH PROCESÓW SEMI-MARKOWA I JEJ ZASTOSOWANIE W PROJEKTOWANIU I EKSPLOATACJI OKRĘTOWYCH SILNIKÓW GŁÓWNYCH I INNYCH URZĄDZEŃ SIŁOWNI OKRĘTOWYCH
PublicationW referacie zaprezentowano znaczenie teorii procesów semi-Markowa w naukach technicznych, zwłaszcza w teorii niezawodności urządzeń technicznych, teorii bezpieczeństwa ich działania oraz statystycznej teorii podejmowania decyzji eksploatacyjnych. W referacie wyeksponowano także przydatność teorii procesów semi-Markowa w teorii i praktyce eksploatacji wspomnianych urządzeń technicznych na przykładzie tak istotnych urządzeń w transporcie...
-
Fractional Order Dynamic Positioning Controller
PublicationImproving the performance of Dynamic Positioning System in such applications as station keeping, position mooring and slow speed references tracking requires improving the position and heading control precision. These goals can be achieved through the improvement of the ship control system. Fractional-order calculus is a very useful tool which extends classical, integer-order calculus and is used in contemporary modeling and control...
-
Relation-based Wikipedia Search System for Factoid Questions Answering
PublicationIn this paper we propose an alternative keyword search mechanism for Wikipedia, designed as a prototype solution towards factoid questions answering. The method considers relations between articles for finding the best matching article. Unlike the standard Wikipedia search engine and also Google engine, which search the articles content independently, requiring the entire query to be satisfied by a single article, the proposed...
-
Balancing energy processes in turbine engines
PublicationThe article discusses the issue of balancing energy processes in turbine engines in operation in aeronautic and PDULQHSURSXOVLRQV\VWHPVZLWKWKHDLPWRDQDO\VHDQGHYDOXDWH EDVLFRSHUDWLQJSDUDPHWHUV7KH¿UVWSDUWSUHVHQWV the problem of enormous amounts of energy needed for driving fans and compressors of the largest contemporary turbofan engines commonly used in long-distance aviation. The amounts of the transmitted power and the effect RIÀRZSDUDPHWHUVDQGFRQVWUXFWLRQDOSURSHUWLHVRIWKHHQJLQHV RQWKHLUSHUIRUPDQFHDQGUHDOHI¿FLHQF\DUH evaluated....
-
The realization of ASON/GMPLS control plane
PublicationASON (Automatic Switched Optical Network) is a concept of optical network recommended in G.8080/Y.1304 by ITU-T. Control Plane of this network could be based on GMPLS (Generalized Multi-Protocol Label Switching) protocols like RSVP-TE, OSPF-TE, LMP. This solution is named ASON/GMPLS. In this chapter we present the control plane problems and proposes ASON/GMPLS network realization that are tested on testbed consists of three and...
-
Study of Noise Propagation for Small Vessels
PublicationThe paper presents the results of the noise propagation analysis in ship structures tested in a number of AHTS (Anchor Handling Tug Supply) vessels. Statistical Energy Analysis (SEA) based on numerical model developed specially for the purpose of this numerical investigation were conducted. This numerical model enabled the analysis of both the structural elements and the acoustic spaces. For the detailed studies 47 points fixed...
-
ENERGY ANALYSIS OF THE PROPULSION SHAFT FATIGUE PROCESS IN A ROTATING MECHANICAL SYSTEM PART III DIMENSIONAL ANALYSIS
PublicationThis article presents the third and last part of the problem of diagnosing the fatigue of marine propulsion shafts in terms of energy with the use of the action function, undertaken by the authors. Even the most perfect physical models of real objects, observed under laboratory conditions and developed based on the results of their research, cannot be useful in diagnostics without properly transferring the obtained results to the...
-
Manoeuvring forces on azimuthing podded propulsor model
PublicationThis paper presents the preliminary part of comprehensive manoeuvring open- water tests of a gas carrier model. The paper focuses on open water experiments with an azimuthing podded propulsor. The test program was carried out in the cavitation tunnel and the large towing tank of Ship Hydromechanics Division, Ship Design and Research Centre, Gdańsk. The pod was tested as a pushing unit with a 161.3 mm diameter propeller. Steering...
-
Validation of atmospheric aerosols parallel sampling in a multifold device
PublicationIn this work, particulate matter was collected using an active sampling system consisting of a PM10 (<10 μm) inlet coupled to a multifold device containing six channels, connected to a vacuum pump. Each channel was equipped with a filter holder fitted with adequately chosen filters. The system was fixed on a metallic structure, which was placed on the roof of the laboratory building, at the Faculty of Sciences, in Lisbon. Sampling...
-
A solid phase extraction–ion chromatography with conductivity detection procedure for determining cationic surfactants in surface water samples
PublicationA new analytical procedure for the simultaneous determination of individual cationic surfactants (alkyl benzyl dimethyl ammonium chlorides) in surface water samples has been developed. We describe this methodology for the first time: it involves the application of solid phase extraction (SPE – for sample preparation) coupled with ion chromatography–conductivity detection (IC-CD – for the final determination). Mean recoveries of...
-
Analiza warunków pracy silnika spalinowego lokomotywy na biegu jałowym
PublicationW trakcie eksploatacji lokomotyw z silnikami spalinowymi obserwowany jest znaczny udział pracy silnika spalinowego w stanie biegu jałowego. Dlatego też średnia wartość strumienia paliwa zużywanego przez silnik spalinowy lokomotywy w tym stanie będzie miała istotny wpływ na efektywność energetyczną układu napędowego. Wyznaczaniu wartości tego parametru musi towarzyszyć jednoznaczna klasyfikacja warunków pracy układu napędowego lokomotywy....
-
Experimental research on over-laminated steel sandwich panel connection to determine the form of fatigue failure
PublicationThe novel means of transport need to meet rising both the economic and ecologic requirements. In recent years the International Maritime Organization (IMO) introduced new measure of ship energy efficiency (the EEDI index), as well as new regulations regarding higher quality of fuel (so called Tier limits). It resulted in much higher interest of the technological development of ships. One of the solution having great potential is...
-
Towards evaluation of the Second Generation Intact Stability Criteria - examination of a fishing vessel vulnerability to surf-riding, based on historical capsizing
PublicationThe Second Generation Intact Stability Criteria (SGISC) are the latest achievements in the field of intact ship stability assessment. The criteria are the result of massive international cooperative efforts and extensive research that lasted more than 15 years. Even though they are based on a solid scientific foundation, the trial period has commenced to collect user experience and further validation. One of possible approaches...
-
Classification of Sea Going Vessels Properties Using SAR Satellite Images
PublicationThe aim of the project was to analyze the possibility of using machine learning and computer vision to identify (indicate the location) of all sea-going vessels located in the selected area of the open sea and to classify the main attributes of the vessel. The key elements of the project were to download data from the Sentinel-1 satellite [1], download data on the sea vessels [2], then automatically tag data and develop a detection...
-
Prediction of manoeuvring abilities of 10000 DWT pod-driven coastal tanker
PublicationThis paper aims to present a new approach in the prediction of manoeuvring abilities of pod-driven ships. A new mathematical model of motions based on MMG methodology was developed and a new type of description of forces acting on azimuth drives is presented. Captive model tests of medium-size coastal tanker and pod open water tests were carried out in CTO S.A. (Ship Design and Research Centre S.A.) to obtain hull hydrodynamic derivatives...
-
An Efficient Framework For Fast Computer Aided Design of Microwave Circuits Based on the Higher-Order 3D Finite-Element Method
PublicationIn this paper, an efficient computational framework for the full-wave design by optimization of complex microwave passive devices, such as antennas, filters, and multiplexers, is described. The framework consists of a computational engine, a 3D object modeler, and a graphical user interface. The computational engine, which is based on a finite element method with curvilinear higher-order tetrahedral elements, is coupled with built-in...
-
Ewolucyjne planowanie bezpiecznych trajektorii statków oparte na zmodyfikowanym diagramie Cockcrofta.
PublicationArtykuł przedstawia kontynuację badań autora nad planowaniem bezpiecznych trajektorii statków za pomocą algorytmów ewolucyjnych. Prezentowana metoda poszukuje optymalnego zbioru bezpiecznych trajektorii wszystkich statków biorących udział w spotkaniu. Bieżąca wersja metody zakłada ograniczoną widoczność i obowiązywanie Prawidła 19 Międzynarodowych Przepisów o Zapobieganiu Zderzeniom na Morzu (MPZZM) zamiast Prawideł 11 – 18. Artykuł...
-
Quasi-Static Response
PublicationConcern for the quasi-static response of ship and offshore structures, as required for safety and serviceability assessments. Attention shall be given to uncertainty quantification of quasi-static load and response analysis approaches, and their limitations, including exact and approximate methods for derivation of different acceptance criteria.
-
Broadband communication solutions for maritime ITSs: Wider and faster deployment of new e-navigation services
Publicationn its initial part, the paper presents an overview of popular technologies and systems currently developed or employed in maritime communication. These solutions are used to provide both ship-to-ship and ship-to-shore communication for the purpose of supporting specific services, often dedicated to maritime safety and e-navigation. Utility of such communication systems have been thoroughly verified over the years and their strengths...