Search
Filters
total: 99
filtered: 98
Chosen catalog filters
Search results for: HEAT PUMP
-
New Design of Axial Piston Pump with Displaced Swash Plate Axis of Rotation for Hydro-Mechanical Transmissions
PublicationThis paper presents a prototype design of an axial piston pump with displaced swash plate axis of rotation in two directions of discharge with electronic control intended for installation on a hydraulic-mechanical gearbox dedicated to working machines. The effect of displacement of the swash plate rotation axis on dead space volume and volumetric efficiency is presented. The construction and principle of operation of the capacity...
-
Design Equation for Stirring Fluid by a Stream Pump in a Circulating Tank
PublicationA circulating tank is a very useful theoretical scheme for many fluid-flow objects in several branches of engineering. The motion of the fluid in such objects can be induced in different ways. A stream pump provides an especially interesting possibility; however, the quantitative description of such devices shows some shortcomings. Such a device is analogous to a jet pump, thus has similar advantages (simplicity of construction,...
-
Experimental Research of an Axial Piston Pump with Displaced Swash Plate Axis of Rotation
PublicationThe article describes the influence of displacement of the swash plate rotation axis on the efficiency of axial piston pumps. The dead space volume was defined as the volume of the working chamber in the extreme position of the piston at the end of the pumping phase and its variability was determined as a function of the position of the axis of rotation of the swash plate and the swing angle of swash plate. The influence of swash...
-
New generation of the satellite hydraulic pumps
PublicationHydraulic satellite machines are known and produced in many versions, recognizable by the number of humps on their inner rotor and external gear, and therefore by the number of cooperating gears (satellites). All known shapes were however designed on the base of preliminary assumption that rotor’s and external gear’s pitch lines are formed by merging arcs, tangent to each other in the. This assumption makes calculations easier,...
-
In Situ Verification of Numerical Model of Water Hammer in Slurries
PublicationThis paper presents a numerical model of transient flow in a pressure slurry pipeline network with verification based on in situ measurements. The model, primarily verified in laboratory conditions, has been extended and applied to the case of a large and complex slurry pipeline network in Poland. In the model, the equivalent density concept was applied. In situ experiments were performed for various unsteady flow episodes, caused by...
-
Calculation Program Supporting Switched Capacitor DC-DC Charge Pump Design (CP Design Calculator) - PartI: Preface
PublicationPrzedmiot badań i motywy podjęcia pracy. Metoda badawcza. Nota historyczna nt. konwertera Fibonacciego (Fibonacci multiplier) i pompy ładunkowej Makowskiego ("Makowski charge pump"). Przewidywane cele pracy. Podziękowania
-
New satellite pumps
PublicationStosowanie Maszyn company from Katowice was initiator and originator of newest original high pressure satellite pumps series of types PSM. Construction solution, research and development of these pumps have been conducted by Team of Hydraulics and Pneumatics of Gdansk University of Technology in cooperation with this company within the confines of research project nr R0300103 (source of funds: Ministry of Science and Higher Education)....
-
Metodyka badań rozwojowych nowego typu silników i pomp satelitowych
PublicationResearch and development of new type satellite motors and satellite pumps SM with small geometrical displacement, from 5 to 73 cm3/rev, has been conducted in cooperation with Stosowanie Maszyn company from Katowice (manufacturer of motors and pump SM). The improvement of construction of those machines, especially construction of axial compensation and construction of fluid distribution channels have been the main problem of research...
-
The Discrete-Continuous, Global Optimisation of an Axial Flow Blood Pump
PublicationThis paper presents the results of the discrete-continuous optimisation of an axial flow blood pump. Differential evolution (DE) is used as a global optimisation method in order to localise the optimal solution in a relatively short time. The whole optimisation process is fully automated. This also applies to geometry modelling. Numerical simulations of the flow inside the pump are performed by means of the Reynolds-Average Navier-Stokes...
-
Discrete-continuous optimisation of an axial flow blood pump
PublicationThis paper presents results of discrete-continuous optimisation of an axial flow blood pump. Evolution Strategies (ES) are used as a global optimisation method in order to localise the optimal solution in relatively short time. The whole optimisation process is fully automated. This also applies to geometry modelling. Numerical simulations of the flow inside the pump is performed by means of the Reynolds-Average Navier-Stokes...
-
Field tests on hydrodynamic and hybrid operation of a bi-directional thrust bearing of a pump-turbine
PublicationIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Because of bi-directional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Field Tests on Hydrodynamic and Hybrid Operation of a Bidirectional Thrust Bearing of a Pump-Turbine
PublicationIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Due to the bidirectional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Volumetric and torque efficiency of pumps during start-up in low ambient temperatures
PublicationThe volumetric, torque and total efficiency of hydraulic pumps change during start-up in low ambient temperatures, as well as in thermal shock conditions, un-til they reach the set conditions. The time to reach steady-state conditions de-pends on many parameters: ambient temperature, flow rate, fluid temperature, design of hydraulic units. The author carried out tests of hydraulic pumps in the Hydraulics Laboratory of the Faculty...
-
Selection of drive engines for dredge pumps
PublicationThis paper presents the principles of selecting drive engines for dredge pumps, formulated by this author. In order to formulate them influence of drive engines on dredge pump characteristics and dredger effectiveness, have been analyzed. Also, an analysis of results of the author's operational investigations concerning energy consumption and parameters of excavated soil transport on board dredgers has been performed.
-
Investigation method and mathematical model of pressure losses in hydraulic rotary motor
PublicationTis paper presents a way of determining the coefcient k of the pressure losses Δp (fow drag) in internal ducts 8 Mp of SWSB-63 hydraulic motor. Te coefcient is determined at a fow rate equal to the theoretical capacity Q of the Pt pump feeding the motor , the losses are related to the nominal pressure p in the hydraulic system. Te investigations n followed a model of energy performance of hydraulic rotary motor, proposed by...
-
Methodology of experimental research on efficiency of hydro-mechanical automatic gearbox
PublicationThe article shortly describes the design and principle of operation of the hydromechanical gearbox and presents the methodology and design of test stands used for testing hydromechanical proto-type gearbox developed at Technical University of Gdansk. The article presents an approach according to which, in order to obtain reliable measurement data, it is necessary to separate the tests of the hydraulic and mechanical parts of the...
-
Comparison of experimental results with simulation studies of "digital" hydrostatic transmission
PublicationThe publication presents the results of experimental research on a "digital" hydrostatic transmission conducted at INOE 2000 IHP within the framework of the grant "Method of effective use of the digital hydraulics concept in multi-source hydrostatic drive systems". The primary goal of the research is to compare the effectiveness (efficiency) of using different methods of controlling the pump capacity and the hydraulic motor capacity...
-
An application for a new type of pneumatic engine concept
PublicationHeavy trucks are often equipped with loading and unloading systems like dock levellers with swing lip or telescopic lip. Most of these devices require hydro-electrical energy supply systems (eg. the pump that presses the working substance to the actuators must be propelled by electric engine.) The space taken by pump with electric engine can be reduced on condition that a new type of pneumatic drive will be considered. It is possible...
-
On the durability of the hydraulic satellite motor working mechanism in overload condition
PublicationThe paper presents the newest construction of the hydraulic satellite pump/motor. In this study, the fracture of the hydraulic satellite motor working mechanism is investigated. Factors influencing the durability of satellite working mechanism have been described. The durability of the hydraulic satellite motor working mechanism at a load, corresponding to a pressure of 15 MPa supplied with refined rapeseed oil is very low. Analyses...
-
Introducing agile practices into development processes of safety critical software
PublicationIn this paper we present AgileSafe - a method which supports introduction of agile practices into safety-critical software development processes. To represent safety assurance constraints resulting from the regulatory context, AgileSafe uses assurance case patterns. The knowledge base of AgileSafe helps the user to select the agile practices relevant for the considered software development project. The corresponding assurance case...
-
R&D of satellite pumps and motors with small geometrical displacement supplied with oil and non-flammable liquids
PublicationThe newest construction of satellite motors and self-suction satellite pumps with small geometrical displacement have been described in this article. The characteristics of volumetric and total efficiency of one satellite motor, selected from the series, supplied with oil have been presented. These characteristics have been compared with the orbital motors' characteristics. The remaining specifications of these motors were also...
-
Comparative in vitro research of the Human Aortic Bioprosthesis
PublicationE valuate of the usefulness and reliability of structures based on the analysis of recorded parameters determining the flow through the Human Aortic Bioprosthesis (HAB) have been dealt with. By flow parameters changes determining the performance environment of prosthesis analyzed change of the motion dynamics of the valve leaflets as a function of pressure, thereby determining the degree of alignment of the prosthesis to the performance...
-
Simulation of large thrust-bearing performance at transient states, warm and cold start-up
PublicationThe start-up of a large hydrodynamic thrust bearing of a vertical hydrogenerator is one of the most critical situations during the lifetime of a bearing. Hydrodynamic load capacity is low due to low speed and higher thermal deformations of the pad. A new approach to the simulation of a hydrodynamic bearing is shown in this article. A combination of finite elements method and computational fluid dynamics is used to perform the transient...
-
Two Time-Scale Hierarchical Control of Integrated Quantity and Quality in Drinking Water Distribution Systems
PublicationThe paper considers a feedback optimising control of drinking water distribution systems (DWDS). Although the optimised pump and valves scheduling and disinfectant injection control attracted considerable attention over last two decades most of the contributions were limited to an open-loop optimisation repetitively performed during the DWDS operation. Also, while a strong interaction between the water quantity and quality exists...
-
Chemosensitization of multidrug resistant Candida albicans by the oxathiolone fused chalcone derivatives
PublicationThree structurally related oxathiolone fused chalcone derivatives appeared effective chemosensitizers, able to restore in part sensitivity to fluconazole of multidrug-resistant C.albicans strains. Compound 21 effectively chemosensitized cells resistant due to the overexpression of the MDR1 gene, compound 6 reduced resistance of cells overexpressing the ABC-type drug transporters CDR1/CDR2 and derivative 18 partially reversed fluconazole...
-
Voriconazole-Based Salts Are Active against Multidrug-Resistant Human Pathogenic Yeasts
PublicationVoriconazole (VOR) hydrochloride is unequivocally converted into VOR lactates and valinates upon reaction with silver salts of organic acids. This study found that the anticandidal in vitro activity of these compounds was comparable or slightly better than that of VOR. The Candida albicans clinical isolate overexpressing CaCDR1/CaCDR2 genes, highly resistant to VOR, was apparently more susceptible to VOR salts. On the other hand,...
-
Energy Loss Coefficients ki in a Displacement Pump and Hydraulic Motor used in Hydrostatic Drives
PublicationThe article aims at defining and analysing the energy loss coefficients in design solutions of rotating displacement machines, with a piston machine as an example. The energy losses observed in these machines include mechanical loss, volumetric loss, and pressure loss. The scale and relations between these losses in different machines depend on machine design and manufacturing quality, and on operating parameters. The operating...
-
Lab-in-syringe as a practical technique for automatic microextraction: Evaluation by Blue Applicability Grade Index
PublicationLab-in-syringe (LIS) is a powerful automatic technique that is derived from sequential injection analysis. In LIS, a computer-controlled syringe pump is employed, and its syringe barrel serves as a mixing, reaction, and/or extraction chamber. Until now, the LIS concept has been efficiently employed for the automation of solid-phase microextraction and liquid-phase microextraction protocols as a front-end to a plethora of chromatographic...
-
Compensation of pressure peaks in pwk-type hydraulic pumps
Publicationhydraulic axial pumps equipped with cam-driven commutation unit (pwk pumps) proved their high efficiency up to 55 mpa and ability to work self-sucking, even at high speed. displacement of pwk pump may easily be changed by moving its control cam. full discharge from hydrostatic forces makes such control possible by direct action of a low-energy actuator like proportional electromagnet or stepping motor. that eliminates heavy and...
-
Influence of Gaps’ Geometry Change on Leakage Flow in Axial Piston Pumps
PublicationAxial piston pumps are the core elements of most medium and high-pressure hydraulic systems. High volumetric efficiency and high working pressures are the main advantages of this type of pumps. Therefore it is necessary to accurately calculate the leakage flow through the gaps to design efficient high-pressure pump. The main difficulty of such calculations is the fact, that the gaps change their geometry during pumping process....
-
Synthesis Methods and Favorable Conditions for Spherical Vaterite Precipitation: A Review
PublicationVaterite is the least thermodynamically stable anhydrous calcium carbonate polymorph. It exists very rare in nature, e.g. in some rock formations or as a component of biominerals produced by some fishes, crustaceans or birds. Synthetic vaterite particles are proposed as carriers of active substances in medicines, additive in cosmetic preparations as well as adsorbents. Also, their utilization as a pump for microfluidic flow is...
-
Validation of atmospheric aerosols parallel sampling in a multifold device
PublicationIn this work, particulate matter was collected using an active sampling system consisting of a PM10 (<10 μm) inlet coupled to a multifold device containing six channels, connected to a vacuum pump. Each channel was equipped with a filter holder fitted with adequately chosen filters. The system was fixed on a metallic structure, which was placed on the roof of the laboratory building, at the Faculty of Sciences, in Lisbon. Sampling...
-
APPLICATION OF THE THEORY OF SEMI-MARKOV PROCESSES TO DETERMINE A LIMITING DISTRIBUTION OF THE PROCESS OF CHANGES OF ABILITY AND INABILITY STATES OF FUEL SUPPLY SYSTEMS IN HEAVY FUEL DIESEL ENGINES
PublicationThe paper presents applicability of the theory of semi-Markov processes to determine a limiting distribution of the process of changes of technical states of fuel systems for marine engines running on heavy fuel oils. The proposed study of this process includes the components of such fuel systems like: 1 - injectors, 2 - high pressure hoses, 3 - injection pumps, 4 - low pressure hoses, 5 – fine filters, 6 - coarse filters, 7 – fuel-feed...
-
Influence of Properties of Hydraulic Fluid on Pressure Peaks in Axial Piston Pumps’ Chambers
PublicationThe article concentrates on the research of the pressure peaks in a working chamber of an axial piston pump. The main focus of the article is the influence of fluid properties on the pressure peaks value. Experimental and analytical methods were used to determine the impact of the fluid density, viscosity, compressibility and aeration. The article describes the pressure peak generation process and explains the theoretical basis...
-
Arterial cannula shape optimization by means of the rotational firefly algorithm
PublicationThe article presents global optimization results of arterial cannula shapes by means of the newly modified firefly algorithm. The search for the optimal arterial cannula shape is necessary in order to minimize losses and prepare the flow that leaves the circulatory support system of a ventricle (i.e. blood pump) before it reaches the heart. A modification of the standard firefly algorithm, the so-called rotational firefly algorithm,...
-
DIGITAL HYDRAULICS CIRCUIT BASED ON PWM FUNCTION FOR CONTROLLING HYDRAULIC ACTUATOR POSITION
PublicationHydraulic systems are used in many different industries, such as multi-source hydrostatic drive systems. In traditional hydraulic systems, a proportional servo valve is used to control the position of hydraulic actuators. The low energy efficiency and high cost of these control valves are two major problems with these systems. Digital hydraulics is one of the most unique ideas on how to solve these problems. Researchers like digital...
-
Portable exhaled breath analyzer employing fluctuation-enhanced gas sensing method in resistive gas sensors
PublicationThis paper presents a portable exhaled breath analyser, developed to detect selected diseases. The set-up employs resistive gas sensors: commercial MEMS sensors and prototype gas sensors made of WO3 gas sensing layers doped with various metal ingredients. The set-up can modulate the gas sensors by applying UV light to induce physical changes of the gas sensing layers. The sensors are placed in a tiny gas chamber of a volume...
-
Low-Voltage LDO Regulator Based on Native MOS Transistor with Improved PSR and Fast Response
PublicationIn this paper, a low-voltage low-dropout analog regulator (ALDO) based on a native n-channel MOS transistor is proposed. Application of the native transistor with the threshold voltage close to zero allows elimination of the charge pump in low-voltage regulators using the pass element in a common drain configuration. Such a native pass transistor configuration allows simplification of regulator design and improved performance,...
-
Properties of New Composite Materials Based on Hydroxyapatite Ceramic and Cross-Linked Gelatin for Biomedical Applications
PublicationThe main aim of the research was to develop a new biocompatible and injectable composite with the potential for application as a bone-to-implant bonding material or as a bone substitute. A composite based on hydroxyapatite, gelatin, and two various types of commercially available transglutaminase (TgBDF/TgSNF), as a cross-linking agent, was proposed. To evaluate the impacts of composite content and processing parameters on various...
-
Starter for Voltage Boost Converter to Harvest Thermoelectric Energy for Body-Worn Sensors
PublicationThis paper examines the suitability of selected configurations of ultra-low voltage (ULV) oscilla-tors as starters for a voltage boost converter to harvest energy from a thermoelectric generator (TEG). Important properties of particularly promising configurations, suitable for on-chip imple-mentation are compared. On this basis, an improved oscillator with a low startup voltage and a high output voltage swing is proposed. The applicability...
-
Geometric working volume of a satellite positive displacement machine
PublicationThis article describes a method for determining the geometric working volume of satellite positive displacement machines (pump and motor). The working mechanism of these machines is satellite mechanism consisting of two non-circular gears (rotor and curvature) and circular gears (satellites). Two variants of the satellite mechanism are presented. In the first mechanism, the rolling line of the rotor is a sinusoid "wrapped" around...
-
Comparative study of numerical modelling and experimental investigation for vessel-docking operations
PublicationA comparative study between numerical modelling and experimental investigation is performed to validate the developed numerical method for simulating floating dock operations with a vessel on board. Both model-scale and full-scale experimental tests are performed on floating docks with a vessel on board, and the draughts using draught meters, floating positions and bending of the floating dock are measured. The present numerical...
-
Chemical Theory of Machines, basic principles of strength with examples of calculations
PublicationThis book encompasses the essential range of information on technical aspects of mechanical design. It was written primarily for the students and staff of chemistry faculties of technical universities, yet it may also be utilized by everyone, who ether would like to try or already enjoys designing, but cannot take advantage of typical stress & machine construction handbooks. These handbooks often require familiarity with the concepts...
-
Magnetic field mapping along a NV-rich nanodiamond-doped fiber
PublicationIntegration of NV−-rich diamond with optical fibers enables guiding quantum information on the spin state of the NV− color center. Diamond-functionalized optical fiber sensors have been demonstrated with impressive sub-nanotesla magnetic field sensitivities over localized magnetic field sources, but their potential for distributed sensing remains unexplored. The volumetric incorporation of diamonds into the optical fiber core allows...
-
Mechanisms of azole resistance among clinical isolates of Candida glabrata in Poland
PublicationCandida glabrata is currently ranked as the second most frequently isolated aetiological agent of human fungal infections, next only to Candida albicans. In comparison with C. albicans, C. glabrata shows lower susceptibility to azoles, the most common agents used in treatment of fungal infections. Interestingly, the mechanisms of resistance to azole agents in C. albicans have been much better investigated than those in C. glabrata....
-
Correlation between the number of Pro-Ala repeats in the EmrA homologue of Acinetobacter baumannii and resistance to netilmicin, tobramycin, imipenem and ceftazidime
PublicationAcinetobacter baumannii coccobacilli are dangerous to patients in intensive care units because of their multidrug resistance to antibiotics, developed mainly in the past decade. This study aimed to examine whether there is a significant correlation between the number of Pro-Ala repeats in the CAP01997 protein, the EmrA homologue of A. baumannii, and resistance to antibiotics. A total of 79 multidrug-resistant A. baumannii strains...
-
Load effect impact on the exploitation of concrete machine foundations used in the gas and oil industry
PublicationMachine foundations is a critical topic in the gas and oil industry, which design and exploitation require extensive technical knowledge. Machine foundations are the constructions which are intended for mounting on it a specific type of machine. The foundation has to transfer dynamic and static load from machine to the ground. The primary difference between machine foundations and building foundations is that the machine foundations...
-
Combinated treatment of landfill leachates with wastewater in a sequencing batch reactor (SBR)
PublicationSanitary landfill leachates are treated usually by multistage systems using physical, chemical and biological processes. One of the most economic and efficient method is combined treatment of landfill leachates with municipal wastewater in a sequencing batch reactor (SBR. The main advantage of such co-treatment is that landfill leachates variability (in quality and quantity) do not influence the effectiveness of biological processes....