Filters
total: 412
filtered: 237
Search results for: scan
-
Laser scanning as a source of information in the analysis of the facades of heritage at risk – the mansion in Kliczewo Male
Publication -
Sensitivity calibration procedures in optical‐CT scanning of BANG®3 polymer gel dosimeters
Publication -
Inner-Tube Chirality Determination for Double-Walled Carbon Nanotubes by Scanning Tunneling Microscopy
Publication -
Algorithm for Automatic Wear Estimation of Railway Contact Strips Based on 3D Scanning Results
PublicationElectric rail vehicles use current collection system which consists of overhead contact line and a current collector (pantograph) mounted on the roof of a vehicle. A pantograph is equipped with contact strips, which slide along the contact wire, ensuring steady electric contact. Contact strips are made of carbon layer, fixed to an aluminum carrier. The carbon layer wears down due to friction. Using overly worn contact strips increases...
-
Modes of Failure Analysis in Reinforced Concrete Beam Using Laser Scanning and Synchro-Photogrammetry
PublicationThe following paper reveal the limitations and possibilities of terrestrial laser scanning technology adaptation in diagnostics of reinforced concrete beams. In this paper, authors present potential spectrum of TLS use in modes of failure analysis of R-C beams and determines under which conditions the laser technologies might be applied. Research was carried out at the Regional Laboratory of Structural Engineering at Gdansk University...
-
High performance filtering for big datasets from Airborne Laser Scanning with CUDA technology
PublicationThere are many studies on the problems of processing big datasets provided by Airborne Laser Scanning (ALS). The processing of point clouds is often executed in stages or on the fragments of the measurement set. Therefore, solutions that enable the processing of the entire cloud at the same time in a simple, fast, efficient way are the subject of many researches. In this paper, authors propose to use General-Purpose computation...
-
Experimental investigations of damage evolution in concrete during bending by continuous micro-CT scanning
PublicationThe paper describes experimental investigation results of fracture in notched concrete beams under quasi-static three-point bending. To visualize 3D fracture in concrete under bending, an extended X-ray micro-computed tomography system was used, i.e. the tomography system SkyScan 1173 was connected to the loading machine ISTRON 5569. This combined system enabled to shot images of deforming concrete beams during a continuous deformation...
-
Bridge Non-Destructive Measurements Using a Laser Scanning during Acceptance Testing: Case Study
PublicationOwing to the recent proliferation of inventory works on roads and railways, bridge acceptance tests have increased exponentially. These tests’ results are often misinterpreted owing to the use of various measuring equipment types, rendering integrated interpretation problematic. It is also problematic that adjusting the measurement method is difficult when the structure’s response to load is uncertain. Therefore, it is important...
-
Application scanning laser measurements and wavlet transform for dmagae detection in composite wind turbine blade
PublicationW pracy przedstawiono wyniki pomiarów postaci drgań własnych kompozytowej łopaty turbiny wiatrowej. Przedstawiono wyniki detekcji uszkodzeń oparte o analize falkową zmierzonych form drgań.
-
The use of terrestrial laser scanning in monitoring and analyses of erosion phenomena in natural and anthropogenically transformed areas
Publication -
Positional Scanning Identifies the Molecular Determinants of a High Affinity Multi-Leucine Inhibitor for Furin and PACE4
Publication -
Application of the Msplitmethod for filtering airborne laser scanning data-sets to estimate digital terrain models
PublicationALS point cloud filtering involves the separation of observations representing the physical terrain surface from those representing terrain details. A digital terrain model (DTM) is created from a subset of points representing the ground surface. The accuracy of the generated DTM is influenced by several factors, including the survey method used, the accuracy of the source data, the applied DTM generation algorithm, and the survey...
-
3D Object Shape Reconstruction from Underwater Multibeam Data and Over Ground Lidar Scanning
PublicationThe technologies of sonar and laser scanning are an efficient and widely used source of spatial information with regards to underwater and over ground environment respectively. The measurement data are usually available in the form of groups of separate points located irregularly in three-dimensional space, known as point clouds. This data model has known disadvantages, therefore in many applications a different form of representation,...
-
ARTIFICIAL MODEL IN THE ASSESSMENT OF THE ALGORITHM OF OBJECTS RECORDED BY LASER SCANNING SHAPE DETECTION (ALS/TLS)
PublicationBrief description of the study and used methods. Brief description of the study and used As part of the preparatory work aimed to create the application solution allowing for the automation of searching objects in data, obtained in the scanning process using ALS (Airborne Laser Scanning) or TLS (Terrestrial Laser Scanning), the authors prepared a artificial (synthetic, theoretical) model of space, used for the verification of operation...
-
Implementation of spatial information for monitoring and analysis of the area around the port using laser scanning techniques
PublicationNowadays, maritime infrastructure is heavily exploited, which requires monitoring. The article presents the implementation of spatial information which are point clouds for monitoring and analysis of the area around the port (buildings and wharves). For this study, point clouds coming from terrestrial (TLS) and airborne laser scanning (ALS), each of them having different accuracy, were used. An important part of the analysis was...
-
In vivo imaging of the human eye using a two-photon excited fluorescence scanning laser ophthalmoscope
PublicationBACKGROUND. Noninvasive assessment of metabolic processes that sustain regeneration of human retinal visual pigments (visual cycle) is essential to improve ophthalmic diagnostics and to accelerate development of new treatments to counter retinal diseases. Fluorescent vitamin A derivatives, which are the chemical intermediates of these processes, are highly sensitive to UV light; thus, safe analyses of these processes in humans...
-
Differential scanning calorimetry as a tool to assess the oxidation state of cold-pressed oils during shelf-life
Publication -
Authenticity Assessment from Sesame Seeds to Oil and Sesame Products of Various Origin by Differential Scanning Calorimetry
Publication -
DSC Melting Profile of Cold-Pressed Hemp Seed Oil as an Authenticity Fingerprint Influenced by Scanning Rate
Publication -
ROYAL CHAPEL IN GDANSK. STUDY OF FACILITY INVENTORY WITH THE USAGE OF LASER SCANNING WITHIN THE FRAMES OF STUDENT PROJECT
PublicationThis article presents the photogrammetric works carried out during the architectural inventory of the Royal Chapel in the Main Town of Gdansk (Poland). The facility has the status of a monument of architecture and since decades it is covered by geodetic monitoring, realized with the participation of the Department of Geodesy of Faculty of Civil and Environmental Engineering of Gdańsk University of Technology . For several years,...
-
Application of Msplit method for filtering airborne laser scanning data sets to estimate digital terrain models
PublicationALS point cloud filtering involves the separation of observations representing the physical terrain surface from those representing terrain details. A digital terrain model (DTM) is created from a subset of points representing the ground surface. The accuracy of the generated DTM is influenced by several factors, including the survey method used, the accuracy of the source data, the applied DTM generation algorithm, and the survey...
-
Crystallization kinetics study of dynamically vulcanized PA6/NBR/HNTs nanocomposites by nonisothermal differential scanning calorimetry
PublicationInvestigation of crystallization behavior and kinetics of thermoplastic elastomer nanocomposites was the subject of limited works because of complexities associated with semiexperimental modeling of such phenomenon in a system containing components having completely different behavior in the molten state. Nonisothermal crystallization kinetics of dynamically vulcanized PA6/NBR/HNTs thermoplastic elastomer nanocomposites was mathematically...
-
On Decomposition-Based Surrogate-Assisted Optimization of Leaky Wave Antenna Input Characteristics for Beam Scanning Applications
PublicationRecent years have witnessed a growing interest in reconfigurable antenna systems. Travelling wave antennas (TWAs) and leaky wave antennas (LWAs) are representative examples of structures featuring a great level of flexibility (e.g., straightforward implementation of beam scanning), relatively simple geometrical structure, low profile, and low fabrication cost. Notwithstanding, the design process of TWAs/LWAs is a challenging endeavor...
-
Evaluation of protective footwear fit for older workers (60+): A case study using 3D scanning technique
Publication -
Investigations on fracture in reinforced concrete beams in 3-point bending using continuous micro-CT scanning
PublicationThis study explores a fracture process in rectangular reinforced concrete (RC) beams subjected to quasi-static three-point bending. RC beams were short and long with included longitudinal reinforcement in the form of a steel or basalt bar. The ratio of the shear span to the effective depth was 1.5 and 0.75. The focus was on the load–deflection diagram and crack formation. Three-dimensional (3D) analyses of the size and distribution...
-
Flicker Noise in Resistive Gas Sensors—Measurement Setups and Applications for Enhanced Gas Sensing
PublicationWe discuss the implementation challenges of gas sensing systems based on low-frequency noise measurements on chemoresistive sensors. Resistance fluctuations in various gas sensing materials, in a frequency range typically up to a few kHz, can enhance gas sensing by considering its intensity and the slope of power spectral density. The issues of low-frequency noise measurements in resistive gas sensors, specifically in two-dimensional...
-
Thermodynamic study of new antiepileptic compounds by combining chromatography on the phosphatidylcholine biomimetic stationary phase and differential scanning calorimetry
Publication -
Evaluating aerial laser scanning for seafloor mapping automation Shallow seabed mapping based on airborne Lidar bathymetry
PublicationThis article presents a novel methodological approach to understand and assess the suitability of ALB for the automatic classification and mapping of the seabed. ALB allows recording of the depth below the Secchi disk.
-
Electrical and mechanical characterization of two-phase alloys by means of scanning probe microscopy in dynamic impedance spectroscopy mode
PublicationDynamic impedance spectroscopy, evaluated for measuring non-stationary systems, was used in combination with scanning probe microscope. Using this approach, localized impedance measurements in the AFM contact mode could be carried out. Additionally, impedance–force curves were made at each phase of investigated materials to illustrate the relation between impedance and the force applied to a probe. Therefore, correlation of electrical...
-
Discrimination of Selected Cold-Pressed and Refined Oils by Untargeted Profiling of Phase Transition Curves of Differential Scanning Calorimetry
Publication -
Processing of point cloud data retrieved from terrestrial laser scanning for structural modeling by Finite Element Method
PublicationFinite Element Method is one most popular contemporary method of strength analysis. The method is an advanced method for solving differential equations, based on discretization, which means that area is divided into finite elements. Each finite element has a solution of the equation approximated by specific functions and performing the actual calculations only for nodes of this division. Finite Element Method is widely used in...
-
Evaluation of water soil erosion processes in forest areas in the Western Sudetes using terrestrial laser scanning and GIS tools
Publication -
Microstructure–Property Relationship of Polyurethane Foams Modified with Baltic Sea Biomass: Microcomputed Tomography vs. Scanning Electron Microscopy
Publication -
Historic bridge modelling using laser scanning, ground penetrating radar and finite element methods in the context of structural dynamics
PublicationPraca dotyczy modelowania MES zabytkowej konstrukcji mostowej przy użyciu danych geometrycznych pochodzących ze skanowania laserowego oraz georadaru. Z uwagi na brak badań materiału budujcego most, przeprowadza się analize wrażliwości konstrukcji na zmiany modułu sprężystości granitu.
-
Microstructure–Property Relationship of Polyurethane Foams Modified with Baltic Sea Biomass: Microcomputed Tomography vs. Scanning Electron Microscopy
PublicationIn this paper, novel rigid polyurethane foams modified with Baltic Sea biomass were compared with traditional petro-based polyurethane foam as reference sample. A special attention was focused on complex studies of microstructure, which was visualized and measured in 3D with high-resolution microcomputed tomography (microCT) and, as commonly applied for this purpose, scanning electron microscopy (SEM). The impact of pore volume,...
-
SU‐FF‐T‐209: New Polymer Gel Dosimeter with High Refractive Index for Artifact‐Free Optical CT Scanning
Publication -
Scanning with Laser Beam over the TiO2 Nanotubes Covered with Thin Chromium Layers towards the Activation of the Material under the Visible Light
Publication -
Oxidative stability assessment of industrial and laboratory-pressed fresh raspberry seed oil (Rubus idaeus L.) by differential scanning calorimetry
Publication -
Assessment of Hemp Seed Oil Quality Pressed from Fresh and Stored Seeds of Henola Cultivar Using Differential Scanning Calorimetry
Publication -
Determining the Behavior of Water in Buttermilk Cheese with Polymerized Whey Protein Using Differential Scanning Calorimetry and Nuclear Magnetic Resonance Analysis
Publication -
Differential scanning calorimetry for authentication of edible fats and oils - What can we learn from the past to face the current challenges?
Publication -
The influence of the grid density of measurement points on damage detection in an isotropic plate by the use of elastic waves and laser scanning Doppler vibrometry
PublicationDamage detection in structural components, especially in mechanical engineering, is an 2 important element of engineering practice. There are many methods of damage detection, in which 3 changes in various parameters caused by the presence of damage are analysed. Recently, methods 4 based on the analysis of changes in dynamic parameters of structures, i.e. frequencies or mode shapes 5 of natural vibrations, as well as changes in...
-
Comparing Different Chemometric Approaches to Detect Adulteration of Cold-Pressed Flaxseed Oil with Refined Rapeseed Oil Using Differential Scanning Calorimetry
Publication -
Investigation of the Dynamism of Nanosized SOA Particle Formation in Indoor Air by a Scanning Mobility Particle Sizer and Proton-Transfer-Reaction Mass Spectrometry
PublicationTerpenes are VOCs of particular importance, since they are emitted from a wide range of indoor sources and are considered to be precursors of Secondary Organic Aerosol (SOA) formation. It has been proven that SOA particles, especially nanosized ones, pose a threat to human health. In this research, experiments with the application of an environmental chamber and real-time measurement techniques were carried out to investigate in...
-
Focused ion beam-based microfabrication of boron-doped diamond single-crystal tip cantilevers for electrical and mechanical scanning probe microscopy
PublicationIn this paper, the fabrication process and electromechanical properties of novel atomic force microscopy probes utilising single-crystal boron-doped diamond are presented. The developed probes integrate scanning tips made of chemical vapour deposition-grown, freestanding diamond foil. The fabrication procedure was performed using nanomanipulation techniques combined with scanning electron microscopy and focused ion beam technologies....
-
Surface roughness analysis of hardened steel after high‐speed milling
Publication -
Radiation dose distributions in three dimensions from tomographic optical density scanning of polymer gels: II. Optical properties of the BANG polymer gel
Publication -
Modes of Failure Analysis in Reinforced Concrete Beam Using Laser Scanning and Synchro-Photogrammetry - How to apply optical technologies in the diagnosis of reinforced concrete elements?
PublicationThe following paper reveal the limitations and possibilities of terrestrial laser scanning technology adaptation in diagnostics of reinforced concrete beams. In this paper, authors present potential spectrum of TLS use in modes of failure analysis of R-C beams and determines under which conditions the laser technologies might be applied. Research was carried out at the Regional Laboratory of Structural Engineering at Gdansk University...
-
Automated Analysis of Images from Confocal Laser Scanning Microscopy Applied to Observation of Calcium Channel Subunits in Nerve Cell Model Line Subjected Electroporation and Calcium
Publication -
Toward Mechanosynthesis of Diamondoid Structures: IX Commercial Capped CNT Scanning Probe Microscopy Tip as Nowadays Available Tool for Silylene Molecule and Silicon Atom Transfer
PublicationAccording to K. E. Drexler, advanced mechanosynthesis will employ advanced nanomachines, but advanced nanomachines will themselves be product of advanced mechanosynthesis. This circular relationship must be broken in SPM technology development. In the article, the possibility of use easy available commercial CNT tips to assembly silicon-based intermediate generations of nano-devices is considered. Mechanosynthesis of a target class...