Filters
total: 296
filtered: 278
Search results for: STEEL FIBRE-REINFORCED CONCRETE
-
Dynamic tests of composite footbridge segment – experimental and numerical studies
PublicationExperimental dynamic tests and numerical simulations of a 3 meters long segment of a footbridge made of polymer composites are presented in the paper. The span-length is reduced, however dimensions of cross-section are the same as the target footbridge. The segment structure is made of sandwich panels, which consist of fibre reinforced polymer (GFRP) laminates (skins) and a PET foam (core). The first part of the paper contains...
-
Impact resistance of plain and twill fabric in GFRP measured by active thermography
PublicationThis paper discusses the impact resistance of glass-fibre reinforced polymer (GFRP) composites depending on the type of reinforcement – plain or twill weave. The values of impact energy were: 3J, 10J and 15J. Specimens featuring twill weave transferred higher force during the impact as compared with plain weave specimens. It was observed that an increase of impact energy was accompanied by an increase of the disproportion in...
-
Experimental Study of Dapped-End Beams Subjected to Inclined Load
PublicationThis paper presents the results of an experimental investigation of the reinforced concrete (RC) dapped-end beams loaded with inclined forces, compared to identical ones loaded with vertical forces only. Such a load may occur in, for example, Gerber's joints or in dapped-end beams supported on corbels, where the vertical gravitation force is additionally completed with horizontal forces caused by temperature differences, shrinking,...
-
Dome over the Gdynia seaport building
PublicationThe paper presents the description of structure and the selected problems of the technical condition, as well as the strength analysis of the thin-walled reinforced concrete shell which has been making a covering of the main hall of the Gdynia Seaport Building through the last 80 years. The rectangle projection of four single curvature shells of the dome was shaped out of mutual perpendicular intersection of two cylindrical shells. The...
-
Local buckling of composite channel columns
PublicationThe investigation concerns local buckling of compressed flanges of axially compressed composite channel columns. Cooperation of the member flange and web is taken into account here. The buckling mode of the member flange is defined by rotation angle a flange about the line of its connection with the web. The channel column under investigation is made of unidirectional fibre-reinforced laminate. Two approaches to member orthotropic...
-
Validation Process for Computational Model of Full-Scale Segment for Design of Composite Footbridge
PublicationExperimental tests and numerical simulations of a full-scale segment of a foot and cycle bridge made of polymer composites are presented in the paper. The analysed structure is made of sandwich panels, which consist of glass fibre reinforced polymer (GFRP) multi-layered laminate faces and a PET foam (obtained from recycling) core. The dimensions of the segment cross-section are the same as for the target footbridge; however, span...
-
Soil-structure interaction effects on modal parameters of office buildings with different number of stories
PublicationThe paper summarizes the results of a numerical investigation designed to study the soil-structure interaction effects on modal parameters of three office buildings. The reinforced-concrete 4-storey, 8-storey, and 12-storey office buildings, each with additional two levels of embedded basements, represent low, medium, and high-rise structures, respectively. In order to conduct this research, detailed finite-element structure models...
-
Evaluating the influence of radiative heat flux on convective heat transfer from a vertical plate in air using an improved heating plate
PublicationThis article examines the influence of radiative heat flux on the accuracy of the results of free convective heat transfer in air. In order to carry out these tests, based on the experience gained during the operation of a plate heated on one side, compensated by a reverse heat loss flux counter-heater, a unique double-sided heating sandwich plate was designed and built, consisting of three thin epoxy resin plates reinforced with...
-
Retrievable strain measuring system in screw displacement piles - readings and results interpretation problems
PublicationStatic load tests on foundation piles are generally carried out in order to determine load – displacement characteristic of the pile. For more detailed information, e.g. force distribution along the shaft, load transfer mechanism and characteristics of soil-structure interaction (unit resistance curves t-z, q-z) additional pile instrumentation is required. Most popular techniques focus on direct concrete strain measurements and...
-
Application of Shape Memory Alloys in Retrofitting of Masonry and Heritage Structures Based on Their Vulnerability Revealed in the Bam 2003 Earthquake
PublicationFor decades, one of the most critical considerations of civil engineers has been the construction of structures that can sufficiently resist earthquakes. However, in many parts of the globe, ancient and contemporary buildings were constructed without regard for engineering; thus, there is a rising necessity to adapt existing structures to avoid accidents and preserve historical artefacts. There are various techniques for retrofitting...
-
Material characterisation of biaxial glass-fibre non-crimp fabrics as a function of ply orientation, stitch pattern, stitch length and stitch tension
PublicationDue to their high density-specific stiffnesses and strength, fibre reinforced plastic (FRP) composites are particularly interesting for mobility and transport applications. Warp-knitted non-crimp fabrics (NCF) are one possible way to produce such FRP composites. They are advantageous because of their low production costs and the ability to tailor the properties of the textile to the reinforcement and drape requirements of the application....
-
Shear Cap Size Selection Method Based on Parametric Analysis of ACI-318 Code and Eurocode 2 Standard
PublicationThe scope of the paper is to propose a method for determining the size of shear caps in a slab–column-connections-reinforced concrete structure. Usually, shear heads are used to enhance slab–column connection, especially when the transverse reinforcement does not give the required punching shear load capacity. The dimensions of the shear head should provide the punching shear resistance of the connection inside and outside the...
-
A universal NDT method for examination of low energy impact damage in CFRP with the use of TLC film
PublicationThe article presents an attempt to use a sheet of laminated thermochromic liquid crystal film (TLC film) for non-destructive testing of the impact damage (energy values: 1J, 2J, 3J and 4J) in carbon fibre-reinforced polymer (CFRP). This is a new, alternative NDT approach based on the thermo-optical effect. The main advantages of this method are a) the low cost of TLC film, b) the low cost of recording devices due to the usage of...
-
Optimized Computational Intelligence Model for Estimating the Flexural Behavior of Composite Shear Walls
PublicationThis article presents a novel approach to estimate the flexural capacity of reinforced concrete-filled composite plate shear walls using an optimized computational intelligence model. The proposed model was developed and validated based on 47 laboratory data points and the Transit Search (TS) optimization algorithm. Using 80% of the experimental dataset, the optimized model was selected by determining the unknown coefficients of...
-
Numerical Study on Seismic Response of a High-Rise RC Irregular Residential Building Considering Soil-Structure Interaction
PublicationThe objective of the present study is to investigate the importance of soilstructure interaction effects on the seismic response of a high-rise irregular reinforced-concrete residential building. In order to conduct this research, a detailed three-dimensional structure model was subjected to various earthquake excitations, also including a strong mining tremor. Soil-foundation flexibility was represented using the spring-based...
-
Application of guided waves in the evaluation of steel-concrete adhesive connection
PublicationThe aim of the paper is the application of guided waves in the evaluation of a condition state of adhesive connection between steel and concrete. The study concerns a push-out specimen consisting of two steel plates glued to opposite faces of a concrete cube with the use of structural adhesive. Wave propagation in the specimen without external load is investigated both experimentally and numerically. The second stage of the investigation...
-
Wave Method for Structural Health Monitoring: Testing Using Full-Scale Shake Table Experiment Data
PublicationAn algorithm of the wave method for structural health monitoring (SHM) is tested and calibrated using shake table experiment data of a full-scale, seven-story, reinforced-concrete building slice. The method is based on monitoring changes in the velocity of waves propagating vertically through the structure, identified by least-squares (LSQ) fit of beam models. The experiment was conducted by a team from the University of California,...
-
Influence of the Shear Cap Size and Stiffness on the Distribution of Shear Forces in Flat Slabs
PublicationThe scope of this paper is to investigate analytically and numerically the influence of shear cap size and stiffness on the distribution of shear forces in flat slabs in a slab–column-connections-reinforced concrete structure. The effect of support (shear cap) stiffness on the calculation of the length of the shear control perimeter according to the available methods is presented. Based on the analysis, the authors indicate in...
-
Aluminium Profile Reinforced with Carbon Fibre: Numerical Analysis
Publication -
Guided wave propagation for assessment of adhesive bonding between steel and concrete
PublicationAdhesive bonding is becoming more increasingly important in joining of structural elements. In civil engineering, there is a growing interest in connection by adhesive bonding in steel-concrete flexural members. This study concerns the guided wave propagation technique applied to condition assessment of an adhesive connection between a steel member and a concrete beam. Various states of degradation were considered by producing...
-
Failure Monitoring and Condition Assessment of Steel-Concrete Adhesive Connection Using Ultrasonic Waves
PublicationAdhesive bonding is increasingly being incorporated into civil engineering applications. Recently, the use of structural adhesives in steel-concrete composite systems is of particular interest. The aim of the study is an experimental investigation of the damage assessment of the connection between steel and concrete during mechanical degradation. Nine specimens consisted of a concrete cube and two adhesively bonded steel plates...
-
Analysis of the Surface Stereometry of Alloyed Austenitic Steel after Fibre Laser Cutting using Confocal Microscopy
PublicationThe paper extends the concept of cut edge quality and examines the fibre laser cutting process. A Prima Power Platino Fiber Evo device with a reference speed (RS) of 3500 mm/min was used for laser cutting. In order to analyse the influence of the laser cutting speed on the cut edge quality of X5CrNi18-10 stainless steel sheets, macroscopic studies were conducted on a stereoscopic microscope and surface stereometry on a confocal...
-
Guided wave propagation in debonding detection in CFRP-reinforced steel plate-like structures
PublicationThe present study investigates the guided wave propagation in multilayered steel specimens reinforced with carbon fiber reinforced polymer (CFRP) through theoretical, numerical, and experimental means. The effectiveness of externally bonded reinforcement (EBR) relies heavily on the bonding quality between the CFRP and the substrate. Premature debonding, a prevalent and hazardous defect, can arise from suboptimal manufacturing processes,...
-
Influence of stirrups in a concrete shell on strengthening reinforced concrete column
PublicationTwelve concrete columns, with a 150x150mm square section and three columns with a circular section (d=200mm), are tested to investigate the effect of strengthening by RC jacket. Based on a confined concrete model for axial static loading, an analytical methods, reported in the literature are proposed to predict the behavior of columns with RC jacket. The results support the conception that the effect of strengthening depends...
-
Modification of cement-ash composites with steel fibre addition
PublicationPraca zawiera wyniki badań kompozytów cementowo-popiołowych, w których popiół zastosowano jako częściowy zamiennik cementu. Do kompozytów dodano niewielkie ilości dwóch rodzajów włókien stalowych. Zbadano właściwości techniczne kompozytów. Wytrzymałości kompozytów cementowo-popiołowych z włóknami stalowymi w stosunku do wytrzymałości kompozytów bez włókien po wszystkich okresach wiązania i twardnienia były wyższe od kilku do kilkudziesięciu...
-
Electrochemical investigations on the corrosion behaviour of reinforcing steel in diatomite- and zeolite-containing concrete exposed to sulphuric acid
PublicationCorrosion is a major concern for most structural applications. Its detrimental effect significantly reduces the life of metallic components. This paper presents the results of an experimental investigation of corrosion in the steel reinforcement of concrete samples having three different substituents: 20% diatomite, 20% zeolite, and a reference without zeolite or diatomite. All concrete specimens were subjected to a solution of...
-
Ultrasound monitoring for evaluation of damage in reinforced concrete
PublicationThe paper deals with automated monitoring of damage evolution in concrete elements subjected to three-point bending tests. The monitoring is based on the nonlinear interactions of traveling ultrasonic waves with micro-crack zones inside the concrete specimens and surface-breaking cracks. The developed procedure assumes semi-continuous ultrasonic testing during the element full loading cycle and generation of the power spectral...
-
Minimal transverse reinforcement of reinforced concrete members
PublicationW pierwszej części pracy omówiono zagadnienia dotyczące minimalnego zbrojenia na ścinanie elementów żelbetowych w kontekście norm europejskich oraz pozaeuropejskich. W drugiej części pracy dokonano analizy wyników badań eksperymentalnych dotyczących nośności elementów bez zbrojenia poprzecznego, które stanowią podstawę do weryfikacji zaleceń normowych w zakresie minimalnego zbrojenia na ścinanie.
-
Fragility analysis of structural pounding between adjacent structures arranged in series with various alignment configurations under near‑field earthquakes
PublicationA major cause of local to total damages is related to structural pounding in a large number of past earthquakes. In general, these collisions take place as a result of differences in the dynamic characteristics of the colliding structures. To acquire a better perception of the behavior of structures, in this paper, three structures featuring different heights are modeled in series and with various configurations next to each other...
-
Linear viscoelastic transversely isotropic model based on the spectral decomposition of elasticity tensors
PublicationThe linear viscoelasticity is still a useful model in the engineering for studying the behavior of materials loaded with different loading rates (frequencies). Certain types of materials reveal also an anisotropic behavior: fiber reinforced composites, asphalt concrete mixtures, or wood, to name a few. In general, researchers try to identify experimentally the dependence of engineering constants like: directional Young’s moduli...
-
DETECTION OF DEBONDING IN STEEL BARS EMBEDDED IN CONCRETE USING GUIDED WAVE PROPAGATION
PublicationThe paper presents a non-destructive diagnostic technique based on guided wave propagation phenomenon used to assess the adhesive bonding between a steel bar and a concrete cover. Double-layered cylindrical specimens with different levels of debonding and its location were investigated. The influence of bonding length on the excitation of multiple modes of longitudinal guided waves was analysed. Numerical simulations of guided...
-
Non-Destructive Diagnostics of Concrete Beams Strengthened with Steel Plates Using Modal Analysis and Wavelet Transform
PublicationExternally bonded reinforcements are commonly and widely used in civil engineering objects made of concrete to increase the structure load capacity or to minimize the negative effects of long-term operation and possible defects. The quality of adhesive bonding between a strengthened structure and steel or composite elements is essential for effective reinforcement; therefore, there is a need for non-destructive diagnostics of adhesive...
-
Parameter estimation of a discrete model of a reinforced concrete slab
Publication -
3D DEM simulations of fracture in reinforced concrete beams
PublicationArtykuł dotyczy zachowania się belki żelbetowej bez zbrojenia pionowego przy trzypunktowym zginaniu. Belka uległa zniszczeniu wskutek ścinania z powodu obecności nadmiernego zbrojenia podłużnego. Eksperymenty przeprowadzono w skali laboratoryjnej z wykorzystaniem systemu mikro-CT, a następnie odtworzono je w analizach numerycznych stosując metodą elementów dyskretnych 3D (DEM). Zastosowano 4-fazowy model betonu z mezostrukturą,...
-
RMS-based damage identification in adhesive joint between concrete beam and steel plate using ultrasonic guided waves
PublicationAdhesive joints have numerous applications in many branches of industry, such as civil engineering, automotive, aerospace and shipbuilding. As with most structural elements, adhesive joints can experience any damage mechanism, which induces the need for diagnostic testing. Ultrasonic waves are widely used for non-destructive inspection of many structures and their elements, including adhesive joints. Guided wave propagation method...
-
Experimental investigation of Steel–Concrete–Polymer composite barrier for the ship internal tank construction
PublicationTransportation of dangerous cargo by ships demands ensuring an appropriate protection level in case of an accident. Two of the most dangerous accident types resulting in an oil spill are grounding and ship to ship collision. The article presents results of research on a new composite construction for a ship hull that increases structural safety during collision. The concept of semi-elastic Steel–Concrete–Polymer structure is presented....
-
Detection and Imaging of Debonding in Adhesive Joints of Concrete Beams Strengthened with Steel Plates Using Guided Waves and Weighted Root Mean Square
PublicationStrengthening of engineering structures is an important issue, especially for elements subjected to variable loads. In the case of concrete beams or slabs, one of the most popular approaches assumes mounting an external reinforcement in the form of steel or composite elements by structural adhesives. A significant disadvantage of adhesive joints is the lack of access to the adhesive film for visual condition assessment, thus, there...
-
FE analysis of reinforced concrete corbels with enhanced continuum models
PublicationW artykule pokazano wyniki MES symulacji wsporników żelbetowych. Zachowanie wsporników modelowano przy zastosowaniu 3 różnych modeli betonu: sprężysto-plastycznego, degradacji sprężystej i rozmytych rys. Modele rozszerzono o długość mikrostruktury przy zastosowaniu teorii nielokalnej. Wyniki numeryczne porównano z doświadczeniami z literatury.
-
Efektywność skrępowania betonu w grubościennych słupach typu Concrete-Filled Steel Tube o przekroju kołowym
PublicationW słupach typu CFST w stanie granicznym dochodzi do zwiększenia wytrzymałości betonu rdzenia na skutek jego skrępowania. Zaistnienie tego zjawiska zależy od wielu czynników. Jednym z najważniejszych z nich jest sztywność obwodowa płaszcza stalowego. Jej wpływ na efektywność wzrostu wytrzymałości betonu rdzenia przebadano eksperymentalnie na grupie 48 grubościennych słupów CFST. Wykazano, że nadmierne zwiększanie grubości płaszcza...
-
Uniform corrosion monitoring of carbon steel in concrete
Publication -
Damage Detection of Steel-Concrete Composite Beam
Publication -
Uniform corrosion monitoring of carbon steel in concrete.
PublicationW przypadku korozji prętów zbrojeniowych w żelbecie zaobserwowane zostały obszary wzmożonego zaatakowania. Pomiar prądowego i napięciowego szumu elektrochemicznego umożliwia wyznaczenie szybkości korozji ogólnej a zmiany parametrów statystycznych przebiegów szumowych umożliwiają detekcję występowania przestrzennych rejonów intensyfikacji korozji. Przedstawione rezultaty, oparte na wykorzystaniu odpowiedniego układu zastępczego,...
-
Doraźna nośność słupów o przekroju kołowym z rur FRP wypełnionych betonem Badania, teoria, obliczanie
PublicationPraca ma charakter monografii opisującej aktualny stan wiedzy z zakresu badań, teorii i projektowania słupów CFFT (concrete-filled fiber-reinforced polymer tube). Celem prowadzonych przez autora prac studialnych i badań własnych, w tym eksperymentalnych, jest szczegółowa analiza doraźnej nośności i zachowania się słupów CFFT poddanych ściskaniu osiowemu i mimośrodowemu. W pierwszym rozdziale wyjaśniono motywację autora do podjęcia...
-
BEHAVIOR OF REINFORCED CONCRETE BEAMS CONTAINING LIGHTWEIGHT AGGREGATE IN THE TENSILE ZONE
Publication.
-
Experimental investigations of size effect in reinforced concrete beams failing by shear
PublicationW artykule omówiono wyniki doświadczalne efektu skali w zbrojonych betonowych belkach niszczących się przez ścinanie. Doświadczenia wykonano dla belek o różnych wymiarach ze zbrojeniem stalowym i bazaltowym. Podczas doświadczeń pomierzono siłę oraz szerokości lokalizacji i rys. Wyniki porównano z modelem skali wg Bazanta.
-
Numerical analysis of behaviour of reinforced concrete elements under eccentric compression
PublicationPrzedstawiono wyniki modelowania nośności elementów żelbetowych stosując metodę elementów skończonych. Do opisu betonu zastosowano sprężysto-plastyczne prawo materiałowe wg Druckera-Pragera. Do modelowania stali zbrojeniowej zastosowano sprężysto-plastyczne prawo materiałowe według von Misesa. Obliczenia wykonano dla ścian żelbetowych.
-
Effectiveness of Concrete Reinforcement with Recycled Tyre Steel Fibres
Publication -
Steel-fibrous concrete -experiments and a numerical discrete model
PublicationW książce przedstawiono wyniki doświadczalne i numeryczne dotyczące rys w elementach betonowych wzmocnionych włóknami stalowymi dla różnych problemów brzegowych quasi-statycznych. Obliczenia wykonano przy zastosowaniu własnego oryginalnego modelu sieciowego. W modelu beton z włóknami stalowymi był modelowany na poziomie mezo. W obliczeniach uwzględniono strefy kontaktu miedzy kruszywem a zaczynem oraz włóknami a zaczynem.
-
Tubular House - Form Follows Technology, Concrete Shell Structure with Inner Thermal Insulation
PublicationThe aim of this paper is the theoretical analysis of the possibilities and limitations of using an unconventional technology and the original architectural form stemming from it – the building with external construction and internal insulation. In Central European climatic conditions, the traditional solution for the walls of heated buildings relies on using external thermal insulation. This stems from building physics: it prevents...
-
Metric entropy and digital image correlation in deformation dynamics analysis of fibre glass reinforced composite under uniaxial tension
Publication