Search
Filters
total: 2106
filtered: 1912
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: REINFORCEMENT CONCRETE SUPPORT
-
Minimal transverse reinforcement of reinforced concrete members
PublicationW pierwszej części pracy omówiono zagadnienia dotyczące minimalnego zbrojenia na ścinanie elementów żelbetowych w kontekście norm europejskich oraz pozaeuropejskich. W drugiej części pracy dokonano analizy wyników badań eksperymentalnych dotyczących nośności elementów bez zbrojenia poprzecznego, które stanowią podstawę do weryfikacji zaleceń normowych w zakresie minimalnego zbrojenia na ścinanie.
-
Effectiveness of Concrete Reinforcement with Recycled Tyre Steel Fibres
Publication -
The Application of Fibres from Recycled Postconsumer Tyres for Concrete Reinforcement
PublicationPoland as a Member State is obliged to implement the EU specific environmental legislation focused on the reduction, transport and treatment of waste. The Landfill Directive prohibited the landfilling of whole tyres and their by-products. Although the EU Directive of Waste limits the use of tyres as secondary fuel, Poland is still the EU leader in burning tyres in cement kilns. Post-consumer tyres are utilised in a number of...
-
Fibres from recycled post-consumer tyres for concrete reinforcement
PublicationW pracy przedstawiono aktualną sytuację dot. wykorzystania drutu stalowego z recyklingu opon samochodowych. Przedstawiono wyniki badań przeprowadzonych w laboratorium Katedry Konstrukcji Betonowych i Technologii Betonu nad zastosowaniem włókien stalowych z recyklingu do zbrojenia betonu. Otrzymane wyniki porównano z próbkami fibrobetonu uzyskanego na bazie przemysłowo produkowanych włókien stalowych.
-
Evaluation of reinforcement corrosion rate in concrete structures by electrochemical noise measurements
PublicationW pracy przedstawiono wyniki obliczeń rezystancji polaryzacyjnej w układzie złożonym z dwóch elektrod (ze stali węglowej oraz elektrody odniesienia), umieszczonych w otulinie betonowej. Szybkość korozji ulega zmianom uzależnionym od stopnia nasiąknięcia betonu roztworem zawierającym jony chlorkowe. Zmiany rezystancji polaryzacyjnej elektrody stalowej oceniane są na podstawie pomiarów prądowego i potencjałowego szumu elektrochemicznego....
-
Experiments and calibration of a bond-slip relation and efficiency factors for textile reinforcement in concrete
PublicationTextile reinforcement yarns consist of many filaments, which can slip relative each other. At modelling of the global structural behaviour, interfilament slip in the yarns, and slip between the yarns and the concrete can be considered by efficiency factors for the stiffness and strength of the yarns, and by applying a bond-slip relation between yarns and concrete. In this work, an effective and robust method for calibration of...
-
Influence of effective width of flange on calculation and reinforcement dimensioning of beam of reinforced concrete frame
PublicationThe paper analyses the influence of modelling the cross-section of a beam in two-storey reinforced concrete frame of industrial warehouse with dimensions: 18.0 m × 32.0 m using bar elements on the results of bending moments, the value of elastic deflection and the dimensioning of reinforcement due to bending. Six options were considered: a beam as a rectangular section and five T-beam variants with different definitions of effective...
-
The influence of reinforcement on load carrying capacity and cracking of the reinforced concrete deep beam joint
PublicationThe paper presents the results of experimental research of the spatial reinforced concrete deep beam systems orthogonally reinforced and with additional inclined bars. Joint of the deep beams in this research was composed of the longitudinal deep beam with a cantilever suspended at the transversal deep beam. The cantilever deep beam was loaded throughout the depth and the transversal deep beam was loaded at the mid-span by longitudinal...
-
The vibration-based assessment of the influence of elevated temperature on the condition of concrete beams with pultruded GFRP reinforcement
PublicationConcrete beams reinforced with glass fiber reinforced polymer (GFRP) bars subjected to elevated temperature have been experimentally studied. The influence of high temperatures on GFRP-reinforced concrete beams condition has been check both, destructively and nondestructively. The nondestructive tests foresaw vibration-based tests to obtain the natural frequency values after exposure to varying temperatures. The vibration-based...
-
Experimental and numerical assessment of size effect in geometrically similar slender concrete beams with basalt reinforcement
PublicationW artykule przedstawiono doświadczalne i numeryczne wyniki badań efektu skali w geometrycznie podobnych smukłych belkach betonowych ze zbrojeniem bazaltowym. Doświadczenia zostały symulowane stosując metodę elementów skończonych w oparciu o model sprężysto-plastyczny z degradacją sztywności i nielokalnym osłabieniem. Otrzymano dobrą zgodność wyników doświadczalnych z numerycznymi.
-
FE analysis of size effects in reinforced concrete beams without shear reinforcement based on stochastic elasto-plasticity with non-local softening.
PublicationW artykule przedstawiono wyniki analizy MES dotyczącej deterministycznego i statystycznego efektu skali w żelbetowych belkach bez zbrojenia na ścinanie. W analizie zastosowano prawo sprężysto-plastyczne z nielokalnym osłabieniem. Wyniki analizy porównano z doświadczeniami i modelem skali Bazanta.
-
Corrosion behavior of concrete produced with diatomite and zeolite exposed to chlorides
PublicationChloride induced reinforcement corrosion is widely accepted to be the most frequent mechanism causing premature degradation of reinforced concrete structures. The electrochemical impedance of reinforcing steel in diatomite- and zeolite-containing concrete exposed to sodium chloride was assessed. Chemical, physical and mineralogical properties of three concrete samples (20% diatomite, 20% zeolite, and a reference containing neither)...
-
Modelling reinforced concrete beams under mixed shear-tension failure with different continuous FE approaches
PublicationThe paper presents quasi-static numerical simulations of the behaviour of short reinforced concrete beams without shear reinforcement under mixed shear-tension failure using the FEM and four various constitutive continuum models for concrete. First, an isotropic elasto-plastic model with a Drucker-Prager criterion defined in compression and with a Rankine criterion defined in tension was used. Next, an anisotropic smeared crack...
-
Tests of bond between concrete and steel bars – literature background and program of own research
PublicationThis article deals with the issue of the bond between concrete and reinforcement. The bond is crucial for reinforced concrete elements because it is possible to transfer forces (stresses) from concrete to the reinforcement. Basic information related to the cooperation of concrete and rebars was recalled in the article. Selected issues concerning theoretical and numerical analysis as well as experiments of the bond phenomenon were...
-
Experimental and numerical investigations for GPR evaluation of reinforced concrete footbridge
PublicationThe GPR method has increasingly found application in non-destructive testing of reinforced concrete structures. This paper presents the new approach of modelling of the electromagnetic wave propagation for reinforced concrete structures with a complex system of the reinforcement. Simulations of the GPR field were performed on a three-dimensional model of a footbridge using the FDTD method. Numerical maps were compared with results...
-
Investigations on fracture in reinforced concrete beams in 3-point bending using continuous micro-CT scanning
PublicationThis study explores a fracture process in rectangular reinforced concrete (RC) beams subjected to quasi-static three-point bending. RC beams were short and long with included longitudinal reinforcement in the form of a steel or basalt bar. The ratio of the shear span to the effective depth was 1.5 and 0.75. The focus was on the load–deflection diagram and crack formation. Three-dimensional (3D) analyses of the size and distribution...
-
Force transfer and stress distribution in short cantilever deep beams loaded throughout the depth with a various reinforcement
PublicationDeep beams used as the main reinforced concrete structural elements which taking over the load and stiffening construction are often found in high-rise buildings. The architecture of these buildings is sometimes sophisticated and varied, arouse the admiration of the majority of recipients, and thus causing an engineering challenge to correctly design the structural system and force transfer. In such structures is important to shape...
-
Electrochemical investigations on the corrosion behaviour of reinforcing steel in diatomite- and zeolite-containing concrete exposed to sulphuric acid
PublicationCorrosion is a major concern for most structural applications. Its detrimental effect significantly reduces the life of metallic components. This paper presents the results of an experimental investigation of corrosion in the steel reinforcement of concrete samples having three different substituents: 20% diatomite, 20% zeolite, and a reference without zeolite or diatomite. All concrete specimens were subjected to a solution of...
-
Condition of Reinforced Concrete Structures and Their Degradation Mechanism at the Former Auschwitz Concentration and Extermination Camp
PublicationThis paper presents the results of investigations on reinforced concrete structures present in the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp. Field inspection employing the non-destructive method of reinforcement potential measurement according to the ASTM-C 876–15 standard, followed by laboratory investigations performed on genuine historic reinforced concrete samples collected from the...
-
Verification of selected calculation methods regarding shear strength in beams without web reinforcement
PublicationThe purpose of the article was to compare selected calculation methods regarding shear strength in reinforced concrete beams without web reinforcement. Several calculation methods were tested. This included codes: PN-EN 1992-1-1:2008, ACI 318-14 and fib Model Code for Concrete Structures 2010. The analysis also consists of authorial methods published in technical literature. Calculations of shear strengths were made based on experimental...
-
Application of gpr method in diagnostics of reinforced concrete structures
PublicationThis paper presents an application of the ground penetration method (GPR) for diagnostics of reinforced concrete structures. In situ measurements were conducted for three civil engineering structures: the ground floor structure, the abutment of the railway viaduct and the concrete well. The dual polarized ground penetrating radar with the antenna operating at a center frequency of 2 GHz was used for GPR surveys. Three different...
-
Experimental Investigations of Fracture Process Using DIC in Plain and Reinforced Concrete Beams under Bending
PublicationThe fracture behaviour of concrete and reinforced concrete beams under quasi-static three-point bending was comprehensively investigated with experiments at laboratory scale. The eight various concrete mixes were tested. The influence of the shape, volume and size of aggregate particles and reinforcement on concrete fracture under bending was studied. Displacements on the surface of concrete beams were measured by means of the...
-
3D X-ray Micro-CT Analysis of Rebar Corrosion in Reinforced Concrete Subjected to a Chloride-Induced Environment
PublicationThe paper presents experimental investigations of the concrete cover protective ability to coun-teract rebar corrosion in reinforced concrete cubes. To study and quantify the consequences of corrosion a reinforced concrete sample was subjected to chloride-induced environment in order to get corroded and combined with un-corroded sample. Chloride-accelerated technique can in-duce a high degree of corrosion within at a controlled...
-
Shear resistance of low height precast concrete lintels
PublicationThe scope of the paper is to investigate analytically and determine experimentally the shear resistance of low height reinforced precast concrete lintels. The chosen procedures included in national and international standards applied for the design of structural concrete elements to an estimation of shear behaviour of reinforced concrete elements are described. The characteristic and designed shear strength of precast concrete...
-
Remote sensing and photogrammetry techniques in diagnostics of concrete structures
PublicationRecently laser scanning technologies become widely used in many areas of the modern economy. In the following paper authors show a potential spectrum of use Terrestrial Laser Scanning (TLS) in diagnostics of reinforced concrete elements. Based on modes of failure analysis of reinforcement concrete beam authors describe downsides and advantages of adaptation of terrestrial laser scanning to this purpose, moreover reveal under which...
-
A novel formulation of 3D spectral element for wave propagation in reinforced concrete
PublicationThe paper deals with numerical simulations of wave propagation in reinforced concrete for damage detection purposes. A novel formulation of a 3D spectral element was proposed. The reinforcement modelled as the truss spectral element was embedded in the 3D solid spectral finite element. Numerical simulations have been conducted on cuboid concrete specimens reinforced with two steel bars. Different degradation models were considered...
-
3-D finite-difference time-domain modelling of ground penetrating radar for identification of rebars in complex reinforced concrete structures
PublicationThis paper presents numerical and experimental investigations to identify reinforcing bars using the ground penetrating radar (GPR) method. A novel element of the paper is the inspection of different arrangements of reinforcement bars. Two particular problems, i.e. detection of few adjacent transverse bars and detection of a longitudinal bar located over or under transverse reinforcement, have been raised. An attention was also...
-
Experimental investigations on concrete beams reinforced with CFRP lamellas
PublicationPaper presents experimental investigation made on two concrete beams reinforced with internal Carbon Fibre Reinforced Polymer (CFRP) lamellas (i.e. strips, bands). The reinforcement geometrical arrangement was similar as in normal concrete beams reinforced with steel bars and stirrups. The beams were destroyed by the shear forces, as intended. Obtained load-carrying capacities were lower as expected: below 40% of a calculated value....
-
Remote sensing in laboratory diagnostics of reinforced concrete elements – current development and vision for the future
PublicationContinuous emergence of new concrete types and kinds of reinforcement, as well as technological solutions in the field of structural engineering have made great demand for diagnostic tests of reinforced concrete elements. New challenges and problems facing people require new more efficient tools for laboratory diagnostics than those commonly used. Remote sensing may be the answer to this demand. In this paper the author describes...
-
Remote sensing in laboratory diagnostics of reinforced concrete elements – current development and vision for the future
PublicationContinuous emergence of new concrete types and kinds of reinforcement, as well as technological solutions in the field of structural engineering have made great demand for diagnostic tests of reinforced concrete elements. New challenges and problems facing people require new more efficient tools for laboratory diagnostics than those commonly used. Remote sensing may be the answer to this demand. In this paper the author describes...
-
Load-carrying capacity of axially loaded concrete-filled steel tubular columns made of thin tubes
PublicationAn experimental investigation was conducted on 30 CFST columns. An influence of the following factors on load-carrying capacity of the investigated columns was analyzed: the column slenderness (l1 = 42, l2 = 27 and l3 = 15), the tube thickness (the reinforcement ratio was equal to 4% or 6%), the way of applying the load to CFST columns (through the concrete core or through the entire cross-section), the bond strength between a...
-
Effect of coarse grain aggregate on strength parameters of two-stage concrete
Publication. Two-stage concrete (TSC) is a special type of concrete that the method of its construction and implementation is different from conventional one. In TSC, coarse aggregate particles are first placed in the formwork and voids between them are subsequently injected with a special cementations mixture. TSC has been successfully used in many applications, such as underwater construction, casting concrete sections congested with reinforcement...
-
Mechanical and radiation shielding properties of concrete reinforced with boron--basalt fibers using Digital Image Correlation and X--ray micro--computed tomography
PublicationThe paper presents experimental investigations of the radiation shielding, mechanical and fracture properties of concrete reinforced with 5 kg/m3 of novel basalt fibers infused with boron oxide (BBF). However, further studies concerning other dosages i.e. 1 kg/m3, 10 kg/m3, 15 kg/m3 and 20 kg/m3 are currently carried out. Experiments with neutron source revealed that addition of BBF as a dispersed concrete reinforcement could improve...
-
Experimental tests of reinforced concrete deep-beams
PublicationThe paper presents results of experimental research of the reinforced concrete deep beam with a spatial arrangement. Tested structural elements consist of the cantilever deep beam loaded on the height and transverse deep beam with hanging on it another one. The analysis includes crack morphology, effort of steel and load distribution. The article verified effectiveness of two different kind of reinforcement in both tested deep...
-
The effect of multiaxial geocomposite reinforcement on fatigue performance and crack propagation delay in double-layered asphalt beams
PublicationThe presented study investigates the effect of a recently developed multiaxial geocomposite made of polypropylene geogrid and non-woven fabric on the delay of crack propagation, based on four-point bending tests of large asphalt concrete beams – both for reinforced and non-reinforced specimens. Several approaches are described in this study, including analysis of stiffness modulus decrease and analysis of crack propagation using...
-
Flexural behaviour of concrete slabs reinforced with FRP bars in experiments and according to aci ACI 440.1R guide
PublicationThe paper presents research conducted on two concrete slabs reinforced with the carbon composite bars and two other concrete slabs reinforced with basalt composite bars. The carbon bars were plain, while the basalt ones were ribbed. The slabs were experimentally investigated in the flexural state of effort with the concentrated forces applied. The results are compared with the analytical solution proposed in the guide ACI 440.1R-06...
-
Fatigue Performance of Double-Layered Asphalt Concrete Beams Reinforced with New Type of Geocomposites
PublicationThe reinforcement of asphalt layers with geosynthetics has been used for several decades, but proper evaluation of the influence of these materials on pavement fatigue life is still a challenging task. The presented study investigates a novel approach to the reinforcement of asphalt layers using a new type of geogrid composite, in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions is bonded...
-
A 95-Year-Old Concrete Arch Bridge: From Materials Characterization to Structural Analysis
PublicationThe structural analysis of a 95-year-old concrete arch bridge located in Jagodnik (Poland) is performed in this paper, in order to check its behavior under today’s traffic loads. The mechanical properties of both the concrete and the reinforcement are investigated by testing cores and bar stubs extracted from the bridge. Structural analysis confirms that the bridge meets today’s load requirements in terms of bearing capacity, serviceability...
-
Diagnostics of pillars in St. Mary’s Church (Gdańsk, Poland) using the GPR method
PublicationThe main goal of this study was non-destructive evaluation of pillars in the St. Mary’s Church (Gdańsk, Poland) using the ground penetrating radar (GPR) technique. The GPR inspection was conducted on four brick masonry pillars and five pillars strengthened by reinforced concrete jacketing. Data were acquired with a 2 GHz antenna along longitudinal and transverse profiles. The study involved the estimation of the electromagnetic...
-
Monitoring system of the road embankment
PublicationThe paper presents the monitoring system of the embankment supported on concrete columns and overlaid by a load transfer platform (LTP) with the embedded steel grid. This field investigation was to study the complex inter-action between the columns, the LTP layer, and steel reinforcement via full-scale in situ measurements during erection of the embankment. The study was focused on the behaviour of steel reinforcement and the behaviour...
-
Wpływ ukształtowania zbrojenia na zarysowanie i nośność żelbetowego węzła tarczowego ze wspornikiem
PublicationPraca ma charakter eksperymentalno-teoretyczny i dotyczy zagadnień związanych z żelbetowymi tarczami pracującymi w przestrzennym układzie konstrukcji budynków. Celem niniejszej dysertacji było określenie wpływu głównych parametrów jakimi są sposób ukształtowania zbrojenia i smukłość ścinania na zarysowanie i nośność żelbetowego przestrzennego węzła tarczowego ze wspornikiem. Na podstawie aktualnego stanu wiedzy, opracowano program...
-
Detection and Imaging of Debonding in Adhesive Joints of Concrete Beams Strengthened with Steel Plates Using Guided Waves and Weighted Root Mean Square
PublicationStrengthening of engineering structures is an important issue, especially for elements subjected to variable loads. In the case of concrete beams or slabs, one of the most popular approaches assumes mounting an external reinforcement in the form of steel or composite elements by structural adhesives. A significant disadvantage of adhesive joints is the lack of access to the adhesive film for visual condition assessment, thus, there...
-
Damage Analysis of Tensioning Cable Anchorage Zone of a Bridge Superstructure, Using CDP Abaqus Material Model
PublicationNumerical analysis of the tensioning cables anchorage zone of a bridge superstructure is presented in this paper. It aims to identify why severe concrete cracking occurs during the tensioning process in the vicinity of anchor heads. In order to simulate the tensioning, among others, a so-called local numerical model of a section of the bridge superstructure was created in the Abaqus Finite Element Method (FEM) environment. The...
-
Textile reinforced concrete members subjected to tension, bending, and in-plane loads: Experimental study and numerical analyses
PublicationTextile reinforced concrete has raised increasing research interest during the last years, mainly due to its potential to be used for freeform shell structures involving complex load situations. Yet, most experimental work has focused on test setups with primarily uniaxial loading. In the current work, such setups are complemented with a novel test setup of deep beams, including in-plane bending and shear. Further, nonlinear finite...
-
Non-Destructive Diagnostics of Concrete Beams Strengthened with Steel Plates Using Modal Analysis and Wavelet Transform
PublicationExternally bonded reinforcements are commonly and widely used in civil engineering objects made of concrete to increase the structure load capacity or to minimize the negative effects of long-term operation and possible defects. The quality of adhesive bonding between a strengthened structure and steel or composite elements is essential for effective reinforcement; therefore, there is a need for non-destructive diagnostics of adhesive...
-
Load effect impact on the exploitation of concrete machine foundations used in the gas and oil industry
PublicationMachine foundations is a critical topic in the gas and oil industry, which design and exploitation require extensive technical knowledge. Machine foundations are the constructions which are intended for mounting on it a specific type of machine. The foundation has to transfer dynamic and static load from machine to the ground. The primary difference between machine foundations and building foundations is that the machine foundations...
-
Improvement of the load capacity of the road overpass as a result of repairs after breakage caused by vehicle impacts
PublicationDamage of spans of the overpass caused by impact of underpassing vehicles are a frequent case. Objects that use prefabricated load-bearing elements that are not designed for such impacts are particularly exposed. After impact, such parts suffer extensive damage that need repair. Taking advantages of this recovery actions it is worth to perform strengthening that will protect object against possible future impacts. In this study...
-
Laboratory fatigue assessment of large geocomposite-reinforced double-layered asphalt concrete beams
PublicationGeosynthetic reinforcement of asphalt layers has been used for several decades. Evaluation of the influence of these materials on pavement fatigue life is still ongoing, especially for new types of geocomposites. This paper presents the evaluation of fatigue performance of large asphalt concrete beams reinforced with a new type of composite in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions...
-
Laboratory fatigue assessment of large geocomposite-reinforced double-layered asphalt concrete beams
PublicationGeosynthetic reinforcement of asphalt layers has been used for several decades. Evaluation of the influence of these materials on pavement fatigue life is still ongoing, especially for new types of geocomposites. This paper presents the evaluation of fatigue performance of large asphalt concrete beams reinforced with a new type of composite in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions...
-
Badania eksperymentalne strefy przypodporowej żelbetowych belek częściowo sprężonych
PublicationThis project refers to the study the shear zone, under full and partial prestressing in comparison to beams with passive reinforcement.For comparison, variable parameters have been determined:- a/d (from 1,5 to 3,5) - it's shear span to effective depth of the beam . Assuming constant geometrical quantities, "a" is variable.- 26 beams had no vertical shear reinforcement, and the other 26 had closed stirrups.- prestressing intensity...